T150C / T151C Configurator Customer Name: Machine Name\Model Number: Revision Number: Please note revision history details on last page for updates to existing configurators. Date: Contact Name: Contact Number: Customer Email: T151 T150 #74-1833 Coast Meridian Road, Port Coquitlam, BC, Canada V3C 6G5 Ph# (604) 944-9247 Fax# (604) 944-9267 Configurator Version 6.1 T150/T151 Configuration and Options 1 of 7 Toll Free 1-800-663-8806
Application Details Where on the Machine are you mounting the receiver: If you are mounting the receiver in an enclosure, what material is the enclosure made of: Typically, how far away from the receiver will the operator be using the transmitter: Feet Will the operator have direct line of sight to the receiver: Frequency Band Select the desired Radio Frequency Band (Check one). If you have unsure which frequency band to choose please discuss with your sales representative. 902-928MHz Radio Frequencies for North America. 900MHz typically gets 1500 Feet of range line of sight with an internal antenna. External antennas are available to extend this range. Please discuss options with your sales representative. 2.4-2.483 GHz Radio Frequencies for North, South America, European Union and Asia. 2.4GHz typically gets 900 Feet of range line of sight with an internal antenna. External antennas are available to extend this range. Please discuss options with your sales representative. Receiver Antenna Options Internal antenna (standard) External antenna, Indicate Length 6 foot lead 12 foot lead 20 foot lead T150/T151 Configuration and Options 2 of 7
Transmitter Options T150C OR T151C (Belt Clip Installed) Trigger Can be used as digital or proportional Potentiometer Potentiometer Transmitter Accessories Finger Guard (T150C Only) Magnet Battery Cover Waist Belt (T151C Only) Pendant Connector installed on transmitter (used to bypass the batteries and turn off radio transmissions) Batteries (4 x AA Alkaline) Batteries (4 x AA NiMH) T150/T151 Leather Holster Recharge Dash Cradle CCDOCK Transmitter Time Out Once turned on; the transmitter will remain on until the E-Stop or OFF switch are pressed. As a battery saving feature the transmitter will turn off if there have been no functions activated for: 10 Minutes 1 Hour 4 Hours No Time Out T150/T151 Configuration and Options 3 of 7
Receiver Cable Options Choose ONE of the receiver wiring options Receiver Cable with Pendant 10 Foot Receiver Cable 10 Foot Deutsch Connectors Pendant Connectors None Custom made output cable. See Output Cable Specification document. Pendant Cable Options Choose ONE of the pendant cable options 25 Pendant Cable 33 Pendant Cable 100 Pendant Cable 4 to 12 Pendant Coil None T150/T151 Configuration and Options 4 of 7
T150/T151 Faceplate Choose one of the T150C/T151C Transmitter Faceplates 1-6 Switch with E-Stop 1-7 Switch with E-Stop 1-6 Switch with Power ON/ OFF Note: Switch 7 is Power ON/OFF and must be installed. Digital Output Types (Indicate switch to Battery or Ground) Momentary Output is on while switch is active Latching Pressing the switch the first time turns on the output, the second press turns off the output. Two Button Latching Two switch positions one output. ON button turns on output OFF button turns off output. Proportional Output Types PWM (Pulse Width Modulation) E.g. Apitech 35Hz, 12 VDC Current Control E.g. HAWE 200-800mA, 12VDC Analog (Variable Voltage) E.g. 0-Battery, 0-10 VDC 4 20mA 0-95mA, +/- 95mA Please include part number and spec for proportional valves and outputs If any other output type is required please describe in table or special requirements. T150/T151 Configuration and Options 5 of 7
T150/T151 Label, Switch and Output Type Function Name SW # Switch Type Safety Interlock Type of Output As it will appear on the label Momentary Maintained Lift to Operate Potentiometer SW# + or - to be interlocked with Select from list on previous page or describe required output type. Example: Momentary switch to 12 VDC Trigger N/A N/A SW1 + SW1 SW1 - SW2 + SW2 SW2 - SW3 + SW3 SW3 - SW4 + SW4 SW4 - SW5 + SW5 SW5 - SW6 + SW6 SW6 - SW7 + SW7 SW7 - T150/T151 Configuration and Options 6 of 7
Special Requirements E-Stop Operation (What should the outputs do after the E-Stop is pressed?) Typically all outputs off : Out of Range Operation (What should the outputs do if there is a loss of link or the Transmitter batteries die?) Typically all outputs off : Please indicate any special requirements (i.e.: Special interlocks, time delays, any wishes you may have). T150/T151 Configuration and Options 7 of 7
Revision History Revision Number 2 Changed by Date Change Details Describe in detail exactly what has changed from the previous revision. Customer Sign-Off on Requirements and Label A sign-off of this configuration document and label (following page) is required before an order can be entered. The sign off is only required after the configurator is completed, reviewed and a label has been created and attached. Please print this page, fax (604-944-9267) or scan and email the signed document to your sales representative. Proposal # (to be completed by OMNEX) I, on behalf of, declare that all system requirements, I/O functionality (Name) (Company) and logic, and label artwork (following page), as defined in this document, are correct, and that all OMNEX safety features available for this system have been explained and are understood. (Signature) T150/T151 Configuration and Options 8 of 7