H LG-60H series Features : Universal AC input / Full range (up to 305VAC) Built-in active PFC function Protections: Short circuit / Over current / Over voltage / Over temperature Cooling by free air convection OCP point adjustable through output cable or internal potentiometer IP67 / IP65 design for indoor or outdoor installations Class 2 power unit Three in one dimming function (1~10Vdc or PWM signal or resistance) Suitable for LED lighting and moving sign applications Compliance to worldwide safety regulations for lighting Suitable for dry / damp / wet locations 5 years warranty (Note.10) F 110 M M SELV IP65 IP67 ( for 48V,54V only) ( except for 48V,54V ) -15 A Blank : IP67 rated. Cable for I/O connection. A : IP65 rated. Output voltage and constant current level can be adjusted through internal potentiometer. B : IP67 rated. Constant current level adjustable through output cable with 1~10Vdc or 10V PWM signal or resistance. D (option) : IP67 rated. Timer dimming function, contact MEAN WELL for details. SPECIFICATION MODEL OUTPUT INPUT PROTECTION ENVIRONMENT SAFETY & EMC OTHERS NOTE DC VOLTAGE VOLTAGE ADJ. RANGE Note.6 13.5 ~ 17V CURRENT ADJ. RANGE LOAD REGULATION SETUP, RISE TIME HOLD UP TIME (Typ.) VOLTAGE RANGE FREQUENCY RANGE POWER FACTOR (Typ.) EFFICIENCY (Typ.) AC CURRENT (Typ.) INRUSH CURRENT(Typ.) LEAKAGE CURRENT OVER CURRENT OVER VOLTAGE OVER TEMPERATURE WORKING TEMP. WORKING HUMIDITY STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION Note.8 500ms, 80ms at full load Note.5 90 ~ 305VAC 127 ~ 431VDC UL8750, CSA C22.2 No. 250.0-08 (except for 48V, 54V), EN61347-1, EN61347-2-13 independent, IP65 or IP67, J61347-1, SAFETY STANDARDS Note.7 J61347-2-13 approved ; design refer to UL60950-1, TUV EN60950-1, EN60335-1 EMC IMMUNITY MTBF -15 15V Can be adjusted by internal potentiometer A type only 2.4 ~ 4A 16ms/230VAC 47 ~ 63Hz 230VAC /115VAC 16ms/115VAC at full load PF>0.98/115VAC, PF>0.95/230VAC, PF>0.92/277VAC at full load (Please refer to "Power Factor Characteristic" curve) 87.5% 89% 89.5% 90.5% 90.5% 0.64A / 115VAC 0.32A / 230VAC 0.3A / 277VAC COLD START 55A(t width=265 μs measured at I peak) at 230VAC <0.75mA / 277VAC - V 1.8 ~ 3A 95 ~ 108% Note.4 Protection type : Constant current limiting, recovers automatically after fault condition is removed Hiccup mode, recovers automatically after fault condition is removed 18 ~ 24V 23 ~ 30V 28 ~ 35V 35 ~ 43V 41 ~ 49V 48 ~ 58V 54 ~ 65V 59 ~ 68V Protection type : Shut down o/p voltage, re-power on to recover Shut down o/p voltage, re-power on to recover -40 ~ +70 (Refer to "Derating Curve") ~ 95% RH non-condensing -40 ~ +80, 10 ~ 95% RH ± 0.03%/ (0 ~ 60 ) -24 24V 1.5 ~ 2.5A 10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 / RH Compliance to EN55015, EN61000-3-2 Class C ( load) ; EN61000-3-3 Compliance to EN61000-4-2,3,4,5,6,8,11; EN61547, EN55024, light industry level (surge 4KV), criteria A 338K hrs min. MIL-HDBK-217F (25 ) -30 DIMENSION *61.5*36.8mm (L*W*H) PACKING 0.73Kg; pcs/15.6kg/0.9cuft 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. Please refer to "DRIVING METHODS OF LED MODULE". 5. Derating may be needed under low input voltages. Please check the static characteristics for more details. 6. A type only. 7. Safety and EMC design refer to EN60598-1, CNS15233, GB7000.1, FCC part18. 8. Length of set up time is measured at cold first start. Turning ON/OFF the power supply may lead to increase of the set up time. 9. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again. 10. Refer to warranty statement. 11. To fulfill requirements of the latest ErP regulation for lighting fixtures, this LED power supply can only be used behind a switch without permanently connected to the mains. 1.2 ~ 2A -36 1 ~ 1.7A -42 0.87 ~ 1.45A -48 CONSTANT CURRENT REGION Note.4 9 ~ 15V 12 ~ V 14.4 ~ 24V 18 ~ 30V 21.6 ~ 36V 25.2 ~ 42V 28.8 ~ 48V RATED CURRENT 4A 3A 2.5A 2A 1.7A 1.45A 1.3A RATED POWER 60W 60W 60W 60W 61.2W 60.9W 62.4W RIPPLE & NOISE (max.) Note.2 150mVp-p 150mVp-p 150mVp-p 0mVp-p 0mVp-p 300mVp-p 300mVp-p 17 ~ 22V 22 ~ 27V 0.78 ~ 1.3A VOLTAGE TOLERANCE Note.3 ±2.0% ±1.0% ±1.0% ±1.0% ±1.0% ±1.0% ±1.0% LINE REGULATION ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% TOTAL HARMONIC DISTORTION SHORT CIRCUIT WITHSTAND VOLTAGE ISOLATION RESISTANCE EMC EMISSION 30V 27 ~ 33V ±1.5% ±1.0% ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% I/P-O/P:3.75KVAC I/P-FG:2KVAC O/P-FG:1.5KVAC 36V 33 ~ 40V 42V 40 ~ 46V 48V 44 ~ 53V THD< % when output loading at 115VAC/230VAC input and output loading 75% at 277VAC input -54 54V 32.4 ~ 54V 1.15A 62.1W 300mVp-p 49 ~ 58V 0.69 ~ 1.15A ±1.0% ±0.5% ±0.5%
Mechanical Specification Blank:(HLG -6 0H) Case No.957B Unit:mm SJTW 18AWG A Type:(-_A) IP67 ra ted. Cable for I/O connection. SJTW 18AWG Io ADJ Vo ADJ IP65 rated. Output voltage and constant current level can be adjusted through internal potentiometer. (Can access by removing the rubber stopper on the case.) B Type:(-_B) SJTW 18AWG UL 2517 18AWG DIM+(Blue) DIM-(White) File Name:-SPEC 14-05-30
D Type(option):(-_D) SJTW 18AWG IP67 rated. Timer dimming function, contact MEAN WELL for details. Block Diagram Fosc : 100KHz I/P FG EMI FILTER & RECTIFIERS PFC CIRCUIT O.T.P. O.L.P. POWER SWITCHING PWM & PFC CONTROL RECTIFIERS & FILTER O.L.P. DETECTION CIRCUIT +V -V DIM+ DIM- (B Type) O.V.P. Derating Curve Static Characteristics 100 80 60 40 230VAC Input only 100 90 80 70 60 50 40-40 -25-10 0 15 30 50 60 70 AMBIENT TEMPERATURE ( ) (HORIZONTAL) 90 100 125 135 145 155 165 175 180 0 230 305 INPUT VOLTAGE (V) 60Hz File Name:-SPEC 14-05-30
Power Factor Characteristic 1 0.9 9 0.9 8 0.9 7 0.9 6 0.9 5 0.9 4 0.9 3 0.9 2 0.9 1 0.9 0.8 9 0.8 8 0.8 7 0.8 6 0.8 5 0.8 4 Constant Current Mode 5 0 % 6 0 % 7 0 % 8 0 % 9 0 % 1 0 0 % LOAD (60W) 277V AC 230V AC 115V AC EFFICIENCY vs LOAD (48V Model) series possess superior working efficiency that up to 90.5% can be reached in field applications. 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 % LOAD DRIVING METHODS OF LED MODULE There are two major kinds of LED drive method "direct drive" an d "with LED driver". A typical LED power supply may either work in "constan t voltage mode (CV) or constant current mode (CC)" to drive the LEDs. Mean Well's LED power supply with CV+ CC characteristic can be operated at both CV mode (with LED driver, at area (A) and CC mode (direct drive, at area (B). 277VAC 230VAC 115VAC 100 60 (min.) (A) Constant Voltage area (B) Constant Current area (C) Hiccup Protection In the constant current region, the highest voltage at the output of the driver depends on the configuration of the end systems. Should there be any compatibility issues, please contact MEAN WELL. 50 100 Io (%) Typical LED power supply I-V curve File Name:-SPEC 14-05-30
DIMMING OPERATION (for B-type only) DIM+(Blue) DIM-(White) Built-in 3 in 1 dimming function, IP67 rated. Output constant current level can be a djusted through output cable by connecting a resistance or 1 ~ 10Vdc or 10V PWM signal between DIM+ and DIM-. Please DO NOT connect "DIM-" to "-V". Reference resistance value for output current adjustment (Typical) Resistance value Single driver Multiple drivers (N=driver quantity for synchroni zed dimming operation) Percentage of rated current 10KΩ 60KΩ 10K Ω/N K Ω/N 30K Ω/N 40K Ω/N 50K Ω/N 60K Ω/N 70K Ω/N 80K Ω/N 90K Ω/N 100K Ω/N 1V 2V 3V 4V 5V 6V 7V 8V 9V 10V KΩ % % 30KΩ 40KΩ 1 ~ 10 V dimming function for output current adjustment (Typical) Dimming value Percentage of rated current 50KΩ 70KΩ 10V PWM signal for output current adjustmen t (Typical): Frequency range :100Hz ~ 3KHz Duty value Percentage of rated current % % Dimming connection diagram for turning the lighting fixture ON/OFF : 80KΩ 90KΩ 100KΩ OPEN ----- 95%~ 108% OPEN 95%~ 108% OPEN 95%~ 108% Using the built-in dimming function on B-type model can't turn the lighting fixture totally dark. Please refer to the conne ction method below to achieve 0% brightness of the lighting fixture connecting to the LED power supply unit. Direct connecting to LEDs is suggested, but is not suitable for using additiona l drivers. N FG L Relay Switch Adjuster 10~100K Ohms resistance 1~10V DC Voltage 10V PWM Signal Green/ Yellow Brown Blue AC/L AC/N B Type DIM+ DIM- V(-) V(+) Blue White Black Red LED Lighting Fixture Using a switch and relay can turn ON/OFF the lighting fixture. 1.Output constant current level can be adjusted through output cable by connecting a resistance or 1~10Vdc or 10V PWM signal between DIM+ and DIM-. 2.The LED lighting fixture can be turned ON/OFF by the switch. File Name:-SPEC 14-05-30
WATERPROOF CONNECTION Waterproof connector Waterproof connector can be assembled on the output cable of to operate in dry/wet/damp or outdoor environment. AC source I/P O/P Size Pin Configuration (Female) Size Pin Configuration (Female) M12 Order No. Suitable Current 4-PIN 5A/PIN M12-04 10A max. 5-PIN 5A/PIN M12-05 10A max. M15 Order No. Suitable Current 2-PIN 12A/PIN M15-02 12A max. LED Lamp Cable Joiner 66 26 CJ04-1 suitable for 14AWG~16AWG CJ04-2 suitable for 18AWG~22AWG Up to four wires can be connected through this cable joiner by soldering or clamping by tools. LED Lamp O/P Wires CJ04 cable joiner can be purchased independently fo r user's own assembly. MEAN WELL order No. : CJ04-1, CJ04-2. File Name:-SPEC 14-05-30