Contemporary Round Floor Mounted Tub Filler Thank you for selecting American-Standard... the benchmark of fine quality for over 00 years. To ensure that your installation proceeds smoothly-- please read these instructions carefully before you begin. Recommended Tools Installation Instructions 2064.95 Teflon Tape Pipe Wrench Channel Locks 5mm Hex wrench Electric Drill Phillips Screwdriver Level Flat Blade Screwdriver Adjustable Wrench Round Bubble Level 6mm Hex wrench Tubing Cutter ROUGHING-IN DIMENSIONS 7" (77mm) Certified to comply with ANSI A2.8. -5/6" (287mm) *Adequate floor support is required. The wood support must be a minimum of 2" (5mm) thick by 0" (254mm) wide. 2x6 lumber is NOTadequate for this application. IMPORTANT NOTICE TO THE INSTALLER! Please check with your local Code Authority for acceptable installation requirements for this Roman Tub set with hand shower. Some local codes may require a vacuum breaker and/or a pressure balanced mixing valve to be installed in conjunction with this product. 2-7/8" DIA. (48mm) 5-/8" MAX. (892mm) 47" MAX. (9mm) MOUNTING NUT LOCK WASHER 24" MAX. (609mm) 42" MAX. (067mm) 26-5/6" MAX. (684mm) WASHER LEVELING NUT MOUNTING SCREW 4-/4" x 4-/4" (20 x 20mm) /4" (9mm) ESCUTCHEON FINISHED FLOOR 4" DIA. (0mm) FINISHED FLOOR 2-/4" 70mm MIN. /2" NPT FEMALE THREAD 0" (254mm) MIN. FLOOR JOIST /2" NPT FEMALE THREAD PLASTER GUARD *2" MIN. (5 mm) *WOOD SUPPORT
2" (5mm) MIN. INSTALL TUB FILLER FLOOR SUPPORT CAUTION Turn off hot and cold water supplies before beginning. Note: Refer to Roughing-in Dimensions on page one for additional information. Adequate floor support is required. The WOOD SUPPORT () must be a minimum of 2" (5mm) thick by 0" (254mm) wide. 2x6 lumber is NOT adequate for this application. Locate WOOD SUPPORT () between floor joists keeping a minimum distance of 2-/4" (70mm) from the top surface of wood support to the finished floor. IMPORTANT: Use a ROUND BUBBLE LEVEL (2) to level the WOOD SUPPORT (). The WOOD SUPPORT () must be perfectly level. Secure WOOD SUPPORT () to floor joists. Check for level again. FINISHED FLOOR LINE 0"-2" (254-05mm) WOOD SUPPORT 2 ROUND BUBBLE LEVEL 2-/4" (70mm) MIN. 0" (254mm) MIN. FLOOR JOIST 2 INSTALL AND WATER SUPPLIES Sweat together Hot and Cold Supply assemblies. Apply sealing tape to threaded connections. Thread supply assemblies into rough-in valve inlets. The Hot inlet will be on the left when facing the front of the Tub Filler. Note: The Hot and Cold inlets are marked on the manifold. See View A. SEALING TAPE View A SUPPLY ASSEMBLY 2
INSTALL ROUGH-IN VALVE Locate the position on the wood support where the ROUGH-IN VALVE () will be installed. Use the ROUGH-IN VALVE () as a guide to mark the four mounting hole locations. Fig.. Remove ROUGH-IN VALVE () and drill four pilot holes of /8" (9mm) in diameter. Fig 2. Install the 4 MOUNTING SCREWS (2) into wood support. Install ROUGH-IN VALVE () onto the 4 MOUNTING SCREWS (2) and tighten NUTS & WASHERS (2) supplied. *Important: of ROUGH-IN VALVE () must face bath rim. Figure. NOTE: IF INSTALLING ON A CONCRETE SLAB Drill four pilot holes of 2.5mm (/2") in diameter. Insert a concrete anchor in each pilot hole. Install the 4 MOUNTING SCREWS (2) into the 4 concrete anchors. Tighten NUTS & WASHERS (2) supplied. * Concrete anchor not included. But available commercially. Concrete Anchor S2 (2mm) 2 FRON T FRON T Fig. 2 Fig. 4 LEVEL ROUGH-IN VALVE Check that top of the ROUGH-IN VALVE () is level in all directions. If the ROUGH-IN VALVE () is not level follow the steps below.. Loosen the four MOUNTING NUTS (2). 2. Adjust the LEVELING NUTS (2a) until the TUB FILLER is level in all directions.. Tighten the four MOUNTING NUTS (2) and check that thetub FILLER is still level. If adjustment is still required loosen MOUNTING NUTS (2) and adjust LEVELING NUTS (2a). Verify that the ROUGH-IN VALVE () is level and then fully tighten NUTS & WEASHERS (2). FINISH PLUMBING CONNECTIONS Complete all Hot and Cold supply connections. Turn on water supplies and ckeck for leaks. MOUNTING NUT 2 LOCK WASHER FLAT WASHER *FRO NT LEVELING NUT 2a MOUNTING SCREW
5 FINISH FLOOR INSTALLATION Complete the installation of the Finished Floor. Tile as close to the PLASTER GUARD () as you can. Caulk between Finished Floor and PLASTER GUARD (). FINISHED FLOOR ROUGH FLOOR 6 REMOVE EXPOSED PLASTER GUARD Cut the exposed part of the PLASTER GUARD () flush with the finished floor. Be careful not not damage the floor. FINISHED FLOOR 4
7 REMOVE RETAINING PLATE AND SCREWS Remove the SIX RETAINING PLATE SCREWS (4) with a (5mm) hex wrench. Remove RETAINING PLATE (5). 5mm HEX WRENCH 5 4 FINISHED FLOOR 8 REMOVE AND TEST PLUGS Note: Floor is not shown for clarity in this illustration. Remove the two TEST PLUGS (6) with a (6mm) hex wrench. 6mm HEX WRENCH 6 5
9 INSTALL TUB FILLER Before final installation, check that all sealing surfaces are clean and that the INLET HOSE O-RINGS (7) are not damaged. Important: INLET HOSE O-RINGS (7) can be damaged if caution is not used when installing. Match inlet hose marked with a blue dot with the hole on the manifold also marked with blue dot. (VIEW A ) 7 (VIEW A ) 8 Install the INLET HOSES (8) into the MANIFOLD MOUNTING BASE (9). 9 RED DOT BLUE DOT RED DOT () (VIEW A ) BLUE DOT () 9a INSTALL TUB FILLER Note: A minimum of four MOUNTING SCREWS (0) are required to secure the tub filler. All six are preferred. Install the MOUNTING SCREWS (0) through the MOUNTING PLATE () and into the manifold base. Do not fully tighten. Rotate the TUB FILLER (2) right or left to align with Tub. Tighten MOUNTING SCREWS (0) with 5mm Hex Wrench to secure TUB FILLER (2). 5mm HEX WRENCH 2 0 6
9b INSTALL SPOUT AND HAND SHOWER Align slot in RETAINING RING () with SET SCREW HOLE (4) in SPOUT (5). Install SPOUT (5) onto FAUCET BASE (6). Align SPOUT (5) with bath and tighten SET SCREW (7). (VIEW B ) Install SEALS (8) on both ends of the SPRAY HOSE (9). Connect the end with the hex to the DIVERTER (20) using an adjustable wrench. Hand tighten the connection to the HAND SHOWER (2). Note: When not in use, the HAND SHOWER (2) should be seated in the SHOWER HOLDER (22). 5 6 4 7 7 5 24 25 TEST INSTALLED FAUCET (VIEW B ) (VIEW B ) 22 Move HANDLE (2) onto off position and remove STREAM STRAIGHTENER (24) with KEY (25) supplied. Turn on water supplies and check all connections for leaks. Check MANIFOLD (26) connections for leaks. 28 20 8 2 Apply sealant to underside edge of ESCUTCHEON (27). Slide ESCUTCHEON (27) down to finished floor. Press into place. Clean up excess sealant. 9 Operate HANDLE (2) On to Off and Hot to Cold to flush water lines thoroughly. 2 Lift HAND SHOWER (2) from the HOLDER (22) and direct spray into tub. Rotate DIVERTER KNOB (28) and check HAND SHOWER (2) and SPRAY HOSE (9) connections for leaks. Rotate DIVERTER KNOB (28) back and place HAND SHOWER (2) into HOLDER (22). 27 Re-install STREAM STRAIGHTENER (24). APPLY SEALANT FINISHED FLOOR 26 7
Contemporary Round Floor Mounted Tub Filler MODEL NUMBER 2064.95 Replace the "YYY" with appropriate finish code POLISHED CHROME SATIN NICKEL 002 295 M964978-0070A AERATOR KIT M964980-0070A SPOUT SET SCREW AND SEAL KIT M964976-YYY0A ROUND SHOWER BRACKET KIT M964975-YYY0A ROUND DIVERTER KIT M95472-0070A CARTRIDGE M96265-0070A CARTRIDGE NUT M964972-YYY0A ROUND HANDLE KIT M96497-YYY0A ROUND HAND SHOWER AND HOSE M964979-0070A INLET ADAPTER O-RING KIT LINE FOR HELP For toll-free information and answers to your questions, call: (800) 442-902 Mon. - Fri. 8:00 a.m. to 8:00 p.m. EST Saturday 0:00 a.m. to 4:00 p.m. EST Product names listed herein are trademarks of AS America, Inc. AS America, Inc. 205 8 IN CANADA -800-87-069 (TORONTO -905-06-09) Weekdays 8:00 a.m. to 7:00 p.m. EST IN MEXICO 0-800-89-200