OR OR-TO-L ONNTION 240R SRIS TURS 1.27 mm (0.0 in.) pitch contact arrangement enables high-density mounting. ellows ensure stable contact preventing pins from bending. The bellows also have excellent stability with repeated insertion and extraction. ables and connectors are assembled by discrete wire I. onnectors on the cable side provide superb MI shielding/s protection with an inner-metal and outer-plastic dual cover. onforms to I 1284. Interface Tails are spaced in a four-row staggered arrangement (2.54 mm 1.905 mm) (0.100 in. 0.075 in.) for easy P board design. SPIITIONS Item Operating temperature range urrent rating Voltage rating ontact resistance Insulation resistance ielectric withstand voltage pplicable wire MTRILS Item Insulator onductor Plating 55 to +85 1 240 V mω max. ( 20 mv, 10 m) 1,000 MΩ min. ( 0 V) 7 V for 1 minute WG #28 and #30 stranded wires with φ0.5 to 0.65 mm (0.020 to 0.026 in.) insulation diameter Materials Polyester (UL94V-0) opper alloy ontact Gold plating Terminal Palladium plating ORRING O N-24 5 0-G / : Metal type (board side) or metal type for discrete wire I (cable side) G: Metal type for wire to wire heat bonded multi cable I S: over G: Gold plating : over : Wide-hole cover : 20, 26,,,, or 80 Unit type : Socket R: Plug : over Tail type 0: over 4: Straight 5: Right-angle 7: I 240 series ujitsu connector imensions are in millimeters (inches) www.fcai.fujitsu.com 1
STRIGHT SOKT IMNSIONS 2.7 (0.106) nd terminal 5.2 (0.204) 6.3 (0.248) 9.2 (0.2) 2-M2.6 (0.102) 5.8 (0.228) 3.4 (0.134) 1.3 (0.051) 0.3 (0.011) 1.27 (0.0) 0.4 (0.015) 1.905 (0.075) MOUNTING HOL LYOUT (OMPONNT SI) 26 and ±0.1 (±0.004) ±0.1 (±0.004) 1.27 ±0.1 (0.0 ±0.004 ) nd terminal 20,, and 80 ±0.1 (±0.004) ±0.1 (±0.004) 1.27 ±0.1 (0.0 ±0.004 ) nd terminal 2-φ2.8 (0.110) 2-φ2.8 (0.110) φ0.8 ±0.06 (0.031 ±0.004 ) φ0.8 ±0.06 (0.031 ±0.004 ) PTTRN INHIIT RS ROMMN PNL IMNSIONS 3.2 0 6.6 0.1 (0.259 0.004) ±0.1 (±0.004) 9.7 0 (0.381 0.004) ±0.1 ( ±0.004) R1.5 ±0.1 ( + 0.5) ±0.1 (( + 0.020) ±0.004 ) (R0.059 ±0.004 ) 8.1 ±0.1 (0.318 ±0.004 ) PRT NUMRS N IMNSIONS 20 26 80 N-244020-G/ N-244026-G/ N-2440-G/ N-2440-G/ N-2440-G/ N-244080-G/ 11.43 (0.4) 15.24 (0.600) 21.59 (0.8) 30.48 (1.200) 41.91 (1.6) 49.53 (1.9) 13.45 (0.529) 17.26 (0.679) 23.61 (0.929) 32. (1.279) 43.93 (1.729) 51.55 (2.029) 16.45 (0.647) 20.26 (0.797) 26.61 (1.047) 35. (1.397) 46.93 (1.847) 54.55 (2.147) 27.45 (1.080) 31.26 (1.231) 37.61 (1.480) 46. (1.830) 57.93 (2.280) 65.55 (2.580) 33.35 (1.312) 37.16 (1.462) 43.51 (1.712) 52.40 (2.062) 63.83 (2.512) 71.45 (2.812) 23.30 (0.917) 27.11 (1.067) 33.46 (1.317) 42.35 (1.667) 53.78 (2.117) 61.40 (2.417) imensions are in millimeters (inches) www.fcai.fujitsu.com 2
RIGHT-NGL SOKT [MTL SHLL] IMNSIONS 2.7 (0.106) 1.27 (0.0) 0.4 (0.015) nd terminal 9.4 (0.379) 6.3 (0.248) 2-M2.6 (0.102) 5.2 (0.204) 8.61 (0.338) 11.5 (0.452) 1.3 (0.051) 0.3 (0.011) 2-M2.6 (0.102) 3.9 (0.153) MOUNTING HOL LYOUT (OMPONNT SI) 26 and ±0.1 (±0.004) 1.27 ±0.1 (0.0 ±0.004 ) 20,, and 80 ±0.1 (±0.004) 1.27 ±0.1 (0.0 ±0.004 ) φ 0.8 ±0.06 (0.031 ±0.002 ) ±0.1 (±0.004) 2 φ 2.8 ±0.1 (0.110 ±0.004 ) PTTRN INHIIT RS φ0.8 ±0.06 (0.031 ±0.002 ) ±0.1 (±0.004) 2 φ 2.8 ±0.1 (0.110 ±0.004 ) ROMMN PNL IMNSIONS 3.4 0.1 3.8 0.1 ±0.1 (±0.004) 5.3 0 8.8 0 3.2 0 R1.5 ±0.1 ±0.1 ( ±0.004) (R0.059 ±0.004 ) ( + 0.5) ±0.1 (( + 0.020) ±0.004 ) 8.1 ±0.1 (0.318 ±0.004 ) PRT NUMRS N IMNSIONS 20 26 80 N-2420-G/ N-2426-G/ N-24-G/ N-24-G/ N-24-G/ N-2480-G/ 11.43 (0.4) 15.24 (0.600) 21.59 (0.8) 30.48 (1.200) 41.91 (1.6) 49.53 (1.9) 13.45 (0.529) 17.26 (0.679) 23.61 (0.929) 32. (1.279) 43.93 (1.729) 51.55 (2.029) 16.45 (0.647) 20.26 (0.797) 26.61 (1.047) 35. (1.397) 46.93 (1.847) 54.55 (2.147) 27.45 (1.080) 31.26 (1.231) 37.61 (1.480) 46. (1.830) 57.93 (2.280) 65.55 (2.580) 33.35 (1.312) 37.16 (1.462) 43.51 (1.712) 52.40 (2.062) 63.83 (2.512) 71.45 (2.812) 23.30 (0.917) 27.11 (1.067) 33.46 (1.317) 42.35 (1.667) 53.78 (2.117) 61.40 (2.417) imensions are in millimeters (inches) www.fcai.fujitsu.com 3
RIGHT-NGL SOKT [MTL SHLL] (WITH ORLOKS) IMNSIONS 2.7 (0.106) 1.27 (0.0) 0.4 (0.015) nd terminal 6.3 (0.248) 9.4 (0.370) 2-M2.6 (0.102) 5.2 (0.204) 1.3 (0.051) 11.5 (0.452) 16.3 (0.637) 0.3 (0.011) 3.1(0.122) 3.9 (0.153) MOUNTING HOL LYOUT (OMPONNT SI) 26 and ±0.1 (±0.004) 1.27 ±0.1 (0.0 ±0.004 ) 20,, and 80 ±0.1 (±0.004) 1.27 ±0.1 (0.0 ±0.004 ) φ 0.8 ±0.06 (0.031 ±0.002 ) ±0.1 (±0.004) 2 φ 2.8 ±0.1 (0.110 ±0.004 ) φ0.8 ±0.06 (0.031 ±0.002 ) ±0.1 (±0.004) 2 φ 2.8 ±0.1 (0.110 ±0.004 ) PTTRN INHIIT RS ROMMN PNL IMNSIONS 3.4 0.1 3.8 0.1 ±0.1 (±0.004) 5.3 0 8.8 0 3.2 0 ±0.1 ( ±0.004) R1.5 ±0.1 ( + 0.5) ±0.1 (( + 0.020) ±0.004 ) (R0.059 ±0.004 ) 8.1 ±0.1 (0.318 ±0.004 ) PRT NUMRS N IMNSIONS 20 26 80 N-2420-G/H N-2426-G/H N-24-G/H N-24-G/H N-24-G/H N-2480-G/H 11.43 (0.4) 15.24 (0.600) 21.59 (0.8) 30.48 (1.200) 41.91 (1.6) 49.53 (1.9) 13.45 (0.529) 17.26 (0.679) 23.61 (0.929) 32. (1.279) 43.93 (1.729) 51.55 (2.029) 16.45 (0.647) 20.26 (0.797) 26.61 (1.047) 35. (1.397) 46.93 (1.847) 54.55 (2.147) 27.45 (1.080) 31.26 (1.231) 37.61 (1.480) 46. (1.830) 57.93 (2.280) 65.55 (2.580) 33.35 (1.312) 37.16 (1.462) 43.51 (1.712) 52.40 (2.062) 63.83 (2.512) 71.45 (2.812) 23.30 (0.917) 27.11 (1.067) 33.46 (1.317) 42.35 (1.667) 53.78 (2.117) 61.40 (2.417) imensions are in millimeters (inches) www.fcai.fujitsu.com 4
INSULTION ISPLMNT ONNTION (I) PLUG IMNSIONS ody nd terminal 1.27 (0.0) 6.4 (0.251) 7.5 (0.0) 9 (0.0) 4.5 (0.177) 12.7 (0.0) ssembly drawing ligner cover 1 7.9 (0.311) 3.9 (0.153) ligner cover 2 5 3.9 PRT NUMRS N IMNSIONS 20 26 80 Insulation diameter of applicable wire φ0.5 to 0.65 mm φ0.5 to 0.65 mm φ0.5 to 0.65 mm φ0.5 to 0.65 mm φ0.5 to 0.65 mm φ0.5 to 0.65 mm N-247R020-G/ N-247R026-G/ N-247R0-G/ N-247R0-G/ N-247R0-G/ N-247R080-G/ 21.24 (0.8) 25.05 (0.986) 31.40 (1.2) 40.29 (1.586) 51.72 (2.0) 59.34 (2.3) 17.55 (0.690) 21. (0.840) 27.71 (1.090).60 (1.440) 48.03 (1.890) 55.65 (2.190) 16.55 (0.651) 20. (0.801) 26.71 (1.051) 35.60 (1.401) 47.03 (1.851) 54.65 (2.151) 13.25 (0.521) 17.06 (0.671) 23.41 (0.921) 32.30 (1.271) 43.73 (1.721) 51.35 (2.021) 11.43 (0.4) 15.24 (0.600) 21.59 (0.8) 30.48 (1.200) 41.91 (1.6) 49.53 (1.9) -contact connectors for I of wires with φ0.8 mm (0.031 in.) to φ0.88 mm (0.035 in.) insulation diameter are also available. Specify a part number by replacing -G/ at the end with -G/. imensions are in millimeters (inches) www.fcai.fujitsu.com 5
RIGHT-NGL SOKT [LIGHTWIGHT TYP] IMNSIONS 6.2 (0.244) 2.7 (0.106) No.1 No.2 1.27 (0.0) 0.4 (0.015) 1.27 (0.0) 9.4 (0.370) M2.5 (0.098) 5.2 (0.204) 8.61 (0.338) 11.5 (0.452) 0.3 (0.011) 1.3 (0.051) M2.5 (0.098) 3.9 (0.153) MOUNTING HOL LYOUT (OMPONNT SI) ±0.1 (±0.004) 1.27 ±0.1 (0.0 ±0.004 ) ±0.1 (±0.004) 1.27 ±0.1 (0.0 ±0.004 ) No.1 No.2 No.3 φ 0.8 ±0.06 (0.031 ±0.002 ) 2 φ 2.8 ±0.1 (0.110 ±0.004 ) No.1 No.2 No.3 φ 0.8 ±0.06 (0.031 ±0.002 ) ±0.1 (±0.004) ±0.1 (±0.004) 2 φ 2.8 ±0.1 (0.110 ±0.004 ) PTTRN INHIIT RS ROMMN PNL IMNSIONS 5.3 0 ±0.1 (±0.004) ( + 0.5) ±0.1 (( + 0.020) ±0.004 ) R1.5 ±0.1 (R0.059 ±0.004 ) 3.4 0.1 3.8 0.1 ±0.1 (±0.004) 3.2 0 8.8 0 Recommended panel thickness t = 1 8.1 ±0.1 (0.318 ±0.004 ) PRT NUMRS N IMNSIONS N-24-L/L N-24-L/L 21.59 (0.8) 30.48 (1.200) 23.61 (0.929) 32. (1.279) 26.61 (1.047) 35. (1.397) 37.61 (1.480) 46. (1.830) 43.51 (1.712) 52.40 (2.062) 33.46 (1.317) 42.35 (1.667) This socket is 40% lighter than a socket with die cast shell. imensions are in millimeters (inches) www.fcai.fujitsu.com 6
MI/S RSISTNT OVR IMNSIONS ssembly drawing of cover φ Outer cover able clamp Pan head machine screw Latch 42 (1.653) Inner cover (2) 11.5 Inner cover (1) (0.452) olor: Sand beige PRT NUMRS N IMNSIONS 20 26 80 N-240020-/S N-240026-/S N-2400-/S N-2400-/S N-2400-/S N-2400-/S N-240080-/S 19.95 (0.785) 23.76 (0.935) 30.11 (1.185) 39.00 (1.535).43 (1.985) 58.05 (2.285) 29.65 (1.167) 33.46 (1.317) 39.81 (1.7) 48.70 (1.917) 60.13 (2.7) 67.75 (2.667) 34. (1.358) 38.31 (1.8) 32.00 (1.259) 32.00 (1.259) 32.00 (1.259) 32.00 (1.259) 6.8 (0.2) 7.1 (0.280) 8.2 (0.323) 9.0 (0.354) 9.8 (0.386) 9.1 (0.358) 9.7 (0.382) *: The standard color of the MI/S resistant covers is sand beige, but black, ivory, and art gray are also available. Specify a part number as follows: lack: N-240 - /S-K0. Ivory: N-240 - /S-0. rt gray: N-240 - /S-0. :. : over type. WI-HOL OVR OR SSI LS IMNSIONS able inlet 38.2 (1.4) 19.7 (0.776) 12.4 (0.488) 42.0 (1.654) 33.0 (1.299) 18.5 (0.728) 16.5 (0.6) 49.9 (1.964) 11.5 (0.453) olor: Sand beige PRT NUMRS N IMNSIONS N-2400-/S N-2400-/S able inlet 12.45 11.00 11.05 9.40 R5.5 R4.7 *: The standard color of the MI/S resistant covers is sand beige, but black, ivory, and art gray are also available. Specify a part number as follows: lack: N-240 - /S-K0. Ivory: N-240 - /S-0. rt gray: N-240 - /S-0. :. : over type. imensions are in millimeters (inches) www.fcai.fujitsu.com 7
MI/S RSISTNT OVR, LTH-ON-HOO TYP IMNSIONS φ Outer cover able clamp Pan head machine screw Latch 42 (1.653) Innner cover (2) Innner cover (1) PRT NUMRS N IMNSIONS N-2400-/S N-2400-/S N-2400-/S 29.11 (1.146) 38.00 (1.496) 39.81 (1.567) 48.70 (1.917) 32.00 (1.259) 32.00 (1.259) 8.2 (0.223) 9.0 (0.223) 9.8 (0.223) 11.5 (0.223) 11.5 (0.223) 11.4 (0.223) imensions are in millimeters (inches) www.fcai.fujitsu.com 8
SSORY (UST P OR SOKT) (230R SRIS N 240R SRIS) Used to prevent dust from entering the contact section of a plug connector. IMNSIONS 15 3.8 (0.1) 1.3 (0.051) 1 (0.039) 9.1 (0.358) 4-R2 Material: Polypropylene olor: Sand beige 0-11 7.9 (0.311) PRT NUMRS N IMNSIONS 28 N-230028-11 N-2300-11 N-2300-11 N-2300-11 35.7 (1.406) 40.8 (1.606) 49.7 (1.957) 61.1 (2.406) 30.1 (1.185) 35.2 (1.386) 44.1 (1.7) 55.5 (2.185) PPLITIONS N-23 -G/ N-24 -G/ ust cap N-2300-11 imensions are in millimeters (inches) www.fcai.fujitsu.com 9
L SSMLY TOOLS The following tools are needed to assemble N-230/230R/240/240R series connectors. able aligner (semiautomatic cable aligner or hand tool) I tool 1. able ligner Item ody/ontroller Semiautomatic cable aligner ed daptor Hand tool N-237J N-K560--xxx N-237R N-247J N-M561-/ N-P560-2/ N-K560-R-xxx N-K560-K-xxx N-237T-T062/H N-247R N-P560-2/J N-K560-J-xxx N-247T-T061/H xxx indicates the number of. 2. Insulation isplacement onnection (I) tool Item N-237J N-237R N-237 N-247J N-247R N-247 Hand press N-237T-T109/H Head/Table N-237T-T064/H N-237T-T067/H N-237T-T075/H N-247T-T066/H N-247T-T0/H N-247T-T077/H able aligner Insulation displacement connection (I) tool imensions are in millimeters (inches) www.fcai.fujitsu.com 10
Semi-utomatic Tools able ligning Machine Main ody (N-M551-120, N-M551-220) over 2 over 1 Wires lamp lever pplicator Sinking comb lamp section pplicator Stand able key ed 1. Set the applicator on the stand. Set covers 1 and 2 in the applicator. 2. Push the wire into the sinking combs. 3. Set the applicator onto the installation table and begin cable alignment Head (N-H5-1/) Stand (N-5) Lock Lever Handle Guide Stopper pplicator (N-5-1/-xxx) I Tool (N-237T-T109/H, N-237T-T067/H locator) 4. Take the covers off the applicator. 5. Put covers together and pre-assemble them to the connector body. 6. onduct final aaembly as shown. N-240R SRIS I ROUN-L ONNTORS SOKT: N-247R***-G/ (***: 020, 026, 0, 0, 0,080) Pos No. pplied Wire (wire ia.: mm) onnector Part number Hand Tool able ligner Semi-uto I Tool 20 #28 to #30 (0.5 to 0.65) N-247R020-G/ N-247R080-G/ N-247T-T061/H (See below* ) HN PRSS: N-237T-T109/H H & Locator: N-237T-T067/H Semi-automatic-Medium Level ody: :N-M551-120 Head ssembly: :N-H5 pplicator: :N-5-1/J-***(***: 020, 028, 0, 0, 0, 080) Stand: :N-5 imensions are in millimeters (inches) www.fcai.fujitsu.com 11
ujitsu omponents International Headquarter Offices Japan ujitsu omponent Limited Gotanda-huo uilding 3-5, Higashigotanda 2-chome, Shinagawa-ku Tokyo 141-0022, Japan Tel: (81-3) 5449-7010 ax: (81-3) 5449-2626 mail: promothq@fcl.fujitsu.com Web: www.fcl.fujitsu.com North and South merica ujitsu omponents merica, Inc. 2. aribbean rive Sunnyvale, 94089 U.S.. Tel: (1-408) 745-4900 ax: (1-408) 745-4970 mail: components@us.fujitsu.com Web: http://us.fujitsu.com/components urope ujitsu omponents urope.v. iamantlaan 25 2132 WV Hoofddorp Netherlands Tel: (31-23) 5560910 ax: (31-23) 55609 mail: info@fceu.fujitsu.com Web: emea.fujitsu.com/components sia Pacific ujitsu omponents sia Ltd. 102 Pasir Panjang Road #01-01 itilink Warehouse omplex Singapore 118529 Tel: (65) 6375-8560 ax: (65) 6273-3021 mail: fcal@fcal.fujitsu.com www.fcal.fujitsu.com 2007 ujitsu omponents merica, Inc. ll rights reserved. ll trademarks or registered trademarks are the property of their respective owners. ujitsu omponents merica, Inc. or its affiliates do not warrant that the content of the datatasheet is error free. In a continuing effort to improve our products, ujitsu omponents merica, Inc. or its affiliates reserve the right to change specifications/datasheets witout prior notice. Rev. November 2, 2007. imensions are in millimeters (inches) www.fcai.fujitsu.com 12