N-Channel 3 V (-S) MOSFET PROUCT SUMMARY V S (V) R S(on) () (MAX.) I (A) a Q g (TYP.) 3.84 at V GS = V 37.8.4 at V GS = 4.5 V 32.5 PowerPAK SC-7-6L Single S 4 5 6 8.2 nc FEATURES TrenchFET Gen IV power MOSFET % R g tested The highest continuous drain current capability in its class Very low R S -Q g FOM and Q gd elevate efficiency Increase power density of your design Material categorization: for definitions of compliance please see www.vishay.com/doc?9992 S 7 2 3 G Top View Bottom View Marking Code: AX Ordering Information: -T-GE3 (lead (Pb)-free and halogen-free) 2.5 mm 2.5 mm APPLICATIONS C/C converters and synchronous buck converters - Lower ringing voltage from soft turn-on - High efficiency from fast turn-off G - Lower shoot-through possibility Battery charging and protection Load switch S N-Channel MOSFET ABSOLUTE MAXIMUM RATINGS (T A = 25 C, unless otherwise noted) PARAMETER SYMBOL LIMIT UNIT rain-source Voltage V S 3 V Gate-Source Voltage V GS +2 / -6 T C = 25 C 37.8 T C = 7 C 36.3 Continuous rain Current (T J = 5 C) I T A = 25 C 6. a, b T A = 7 C 2.9 a, b A Pulsed rain Current (t = μs) I M 7 T C = 25 C 5.8 Continuous Source-rain iode Current I S T A = 25 C 2.9 a, b T C = 25 C 9 T C = 7 C 2 Maximum Power issipation P W T A = 25 C 3.5 a, b T A = 7 C 2.2 a, b Operating Junction and Storage Temperature Range T J, T stg -55 to +5 C Soldering Recommendations (Peak temperature) c, d 26 THERMAL RESISTANCE RATINGS PARAMETER SYMBOL TYPICAL MAXIMUM UNIT Maximum Junction-to-Ambient a, e t 5 s R thja 28 36 C/W Maximum Junction-to-Case (rain) Steady state R thjc 5.3 6.5 Notes a. Surface mounted on " x " FR4 board. b. t = 5 s. c. See solder profile (www.vishay.com/doc?73257). The PowerPAK SC-7 is a leadless package. The end of the lead terminal is exposed copper (not plated) as a result of the singulation process in manufacturing. A solder fillet at the exposed copper tip cannot be guaranteed and is not required to ensure adequate bottom side solder interconnection. d. Rework conditions: manual soldering with a soldering iron is not recommended for leadless components. e. Maximum under steady state conditions is 8 C/W. S6-266-Rev. A, 27-Jun-6 ocument Number: 6748 ARE SUBJECT TO SPECIFIC ISCLAIMERS, SET FORTH AT www.vishay.com/doc?9
SPECIFICATIONS (T J = 25 C, unless otherwise noted) PARAMETER SYMBOL TEST CONITIONS MIN. TYP. MAX. UNIT Static rain-source Breakdown Voltage V S V GS = V, I = 25 μa 3 - - V V S Temperature Coefficient V S /T J - 2.8 - I = 25 μa V GS(th) Temperature Coefficient V GS(th) /T J - -4.8 - mv/ C Gate-Source Threshold Voltage V GS(th) V S = V GS, I = 25 μa - 2.4 V Gate-Source Leakage I GSS V S = V, V GS = +2 V / -6 V - - ± na V S = 3 V, V GS = V - - Zero Gate Voltage rain Current I SS V S = 3 V, V GS = V, T J = 55 C - - μa On-State rain Current a I (on) V S 5 V, V GS = V - - A rain-source On-State Resistance a V GS = V, I = A -.7.84 R S(on) V GS = 4.5 V, I = 7 A -.9.4 Forward Transconductance a g fs V S = V, I = A - 35 - S ynamic b Input Capacitance C iss - 29 - Output Capacitance C oss V S = 5 V, V GS = V, f = MHz - 435 - pf Reverse Transfer Capacitance C rss - 3 - V S = 5 V, V GS = V, I = 2 A - 7.6 22 Total Gate Charge Q g - 8.2 6 nc Gate-Source Charge Q gs V S = 5 V, V GS = 4.5 V, I = 2 A - 3. - Gate-rain Charge Q gd -.3 - Gate Resistance R g f = MHz.28.4 2.8 Turn-On elay Time t d(on) - 8 6 Rise Time t r V = 5 V, R L =.5-22 4 Turn-Off elay Time t d(off) I A, V GEN = V, R g = - 8 36 Fall Time t f - 8 6 Turn-On elay Time t d(on) - 2 25 ns Rise Time t r V = 5 V, R L =.5-3 45 Turn-Off elay Time t d(off) I A, V GEN = 4.5 V, R g = - 5 3 Fall Time t f - 3 26 rain-source Body iode Characteristics Continuous Source-rain iode Current I S T C = 25 C - - 2 Pulse iode Forward Current a I SM - - 4 A Body iode Voltage V S I S = A -.85.2 V Body iode Reverse Recovery Time t rr - 3 45 ns Body iode Reverse Recovery Charge Q rr - 2 35 nc I F = A, di/dt = A/μs, T J = 25 C Reverse Recovery Fall Time t a - 7 - ns Reverse Recovery Rise Time t b - 3 - Notes a. Pulse test; pulse width μs, duty cycle 2 %. b. Guaranteed by design, not subject to production testing. Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. S6-266-Rev. A, 27-Jun-6 2 ocument Number: 6748 ARE SUBJECT TO SPECIFIC ISCLAIMERS, SET FORTH AT www.vishay.com/doc?9
TYPICAL CHARACTERISTICS (25 C, unless otherwise noted) 7 V GS = V thru4v 8 I - rain Current (A) 56 42 28 4 V GS = 3 V I - rain Current (A) 6 4 2 T C = 25 C T C = 25 C T C =-55 C.5.5 2 V S - rain-to-source Voltage (V) 2 3 4 V GS - Gate-to-Source Voltage (V) Output Characteristics Transfer Characteristics.2 5 C iss R S(on) - On-Resistance (Ω).5..5 V GS = 4.5 V V GS = V C - Capacitance (pf) 2 9 6 3 C oss C rss 4 28 42 56 7 I - rain Current (A) 6 2 8 24 3 V S - rain-to-source Voltage (V) On-Resistance vs. rain Current and Gate Voltage Capacitance V GS - Gate-to-Source Voltage (V) 8 6 4 2 I = 2 A V S = 5 V V S = 8 V V S = 24 V 5 5 2 Q g - Total Gate Charge (nc) R S(on) - On-Resistance (Normalized).6.4.2..8 V GS = V, I = A V GS = 4.5 V, 7 A.6-5 -25 25 5 75 25 5 T J - Junction Temperature ( C) Gate Charge On-Resistance vs. Junction Temperature S6-266-Rev. A, 27-Jun-6 3 ocument Number: 6748 ARE SUBJECT TO SPECIFIC ISCLAIMERS, SET FORTH AT www.vishay.com/doc?9
TYPICAL CHARACTERISTICS (25 C, unless otherwise noted).3 I S - Source Current (A).. T J = 5 C T J = 25 C R S(on) - On-Resistance (Ω).25.2.5..5 T J = 5 C T J = 25 C..2.4.6.8..2 V S - Source-to-rain Voltage (V) 2 4 6 8 V GS - Gate-to-Source Voltage (V) Source-rain iode Forward Voltage On-Resistance vs. Gate-to-Source Voltage.7 3.5 I = 25 μa 25 V GS(th) (V).3. Power (W) 2 5.9 5.7-5 -25 25 5 75 25 5 T J - Temperature ( C) Threshold Voltage... Time (s) Single Pulse Power, Junction-to-Ambient I M limited Limited by R S(on) () I - rain Current (A) I limited μs ms ms ms. C, s, s T A = 25 C BVSS limited Single pulse.. V S - rain-to-source Voltage (V) () V GS > minimum V GS at which R S(on) is specified Safe Operating Area, Junction-to-Ambient S6-266-Rev. A, 27-Jun-6 4 ocument Number: 6748 ARE SUBJECT TO SPECIFIC ISCLAIMERS, SET FORTH AT www.vishay.com/doc?9
TYPICAL CHARACTERISTICS (25 C, unless otherwise noted) 42 35 I - rain Current (A) 28 2 4 Package limited 7 25 5 75 25 5 T C - Case Temperature ( C) Current erating a 24 2.2 Power (W) 8 2 6 Power (W).76.32.88.44 25 5 75 25 5 T C - Case Temperature ( C). 25 5 75 25 5 T A - AmbientTemperature( C) Power, Junction-to-Case Power, Junction-to-Ambient Note a. The power dissipation P is based on T J (max.) = 5 C, using junction-to-case thermal resistance, and is more useful in settling the upper dissipation limit for cases where additional heatsinking is used. It is used to determine the current rating, when this rating falls below the package limit S6-266-Rev. A, 27-Jun-6 5 ocument Number: 6748 ARE SUBJECT TO SPECIFIC ISCLAIMERS, SET FORTH AT www.vishay.com/doc?9
TYPICAL CHARACTERISTICS (25 C, unless otherwise noted) uty Cycle =.5 Normalized Effective Transient Thermal Impedance.2...5.2 Single Pulse. -4-3 -2 Square Wave Pulse uration (s) Normalized Thermal Transient Impedance, Junction-to-Ambient - Notes: P M t t 2 t. uty Cycle, = t 2 2. Per Unit Base = R thja = 8 C/W 3. T JM - T A = P M Z (t) thja 4. Surface Mounted Normalized Effective Transient Thermal Impedance uty Cycle =.5.2..5. -4.2 Single Pulse -3-2 Square Wave Pulse uration (s) - Normalized Thermal Transient Impedance, Junction-to-Case maintains worldwide manufacturing capability. Products may be manufactured at one of several qualified locations. Reliability data for Silicon Technology and Package Reliability represent a composite of all qualified locations. For related documents such as package/tape drawings, part marking, and reliability data, see www.vishay.com/ppg?6748. S6-266-Rev. A, 27-Jun-6 6 ocument Number: 6748 ARE SUBJECT TO SPECIFIC ISCLAIMERS, SET FORTH AT www.vishay.com/doc?9
Package Information PowerPAK SC7-6L e b e b PIN PIN2 PIN3 PIN PIN2 PIN3 E E2 PIN6 PIN5 PIN4 PIN6 PIN5 PIN4 K3 K K2 K2 K K2 BACKSIE VIEW OF SINGLE A BACKSIE VIEW OF UAL Notes:. All dimensions are in millimeters 2. Package outline exclusive of mold flash and metal burr 3. Package outline inclusive of plating C A E K4 K L L E 2 K K E E3 z Z ETAIL Z SINGLE PA UAL PA IM MILLIMETERS INCHES MILLIMETERS INCHES Min Nom Max Min Nom Max Min Nom Max Min Nom Max A.675.75.8.27.3.32.675.75.8.27.3.32 A -.5 -.2 -.5 -.2 b.23.3.38.9.2.5.23.3.38.9.2.5 C.5.2.25.6.8..5.2.25.6.8..98 2.5 2.5.78.8.85.98 2.5 2.5.78.8.85.85.95.5.33.37.4.53.63.73.2.24.28 2.35.235.335.5.9.3 E.98 2.5 2.5.78.8.85.98 2.5 2.5.78.8.85 E.4.5.6.55.59.63.85.95.5.33.37.4 E2.345.395.445.4.6.8 E3.425.475.525.7.9.2 e.65 BSC.26 BSC.65 BSC.26 BSC K.275 TYP. TYP.275 TYP. TYP K.4 TYP.6 TYP.32 TYP.3 TYP K2.24 TYP.9 TYP.252 TYP. TYP K3.225 TYP.9 TYP K4.355 TYP.4 TYP L.75.275.375.7..5.75.275.375.7..5 T.5..5.2.4.6 ECN: C-743 Rev. C, 6-Aug-7 WG: 5934 ocument Number: 73 6-Aug-7 www.vishay.com
Application Note 826 RECOMMENE PA LAYOUT FOR PowerPAK SC7-6L Single.3 (.2).65 (.26).35 (.4).275 (.).55 (.22).475 (.9) 2.2 (.87).5 (.59).87 (.34).235 (.9).355 (.4).35 (.4).65 (.26).95 (.37).3 (.2) imensions in mm/(inches) Return to Index APPLICATION NOTE ocument Number: 7486 www.vishay.com Revision: 2-Jan-8
Legal isclaimer Notice Vishay isclaimer ALL PROUCT, PROUCT SPECIFICATIONS AN ATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR ESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, Vishay ), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer s technical experts. Product specifications do not expand or otherwise modify Vishay s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. 27 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVE Revision: 8-Feb-7 ocument Number: 9