E M C C o m p o n e n t s May 218 Chip beads For power line MP series (for automotive) MP212 212[85 inch]* * Dimensions code JIS[EIA]
(2/1) EMINDES FO USING THESE PODUCTS Before using these products, be sure to request the delivery specifications. SAFETY EMINDES Please pay sufficient attention to the warnings for safe designing when using this products. EMINDES The storage period is less than 12 months.be sure to follow the storage conditions (temperature:5 to 4 C, humidity:1 to 75% H or less). If the storage period elapses, the soldering of the terminal electrodes may deteriorate. Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). Before soldering, be sure to preheat components. The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 15 C. Soldering corrections after mounting should be within the range of the conditions determined in the specifications. If overheated, a short circuit, performance deterioration, or lifespan shortening may occur. When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal design. Carefully lay out the coil for the circuit board design of the non-magnetic shield type. A malfunction may occur due to magnetic interference. Use a wrist band to discharge static electricity in your body through the grounding wire. Do not expose the products to magnets or magnetic fields. Do not use for a purpose outside of the contents regulated in the delivery specifications. The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions set forth in the each catalog, please contact us. (1) Aerospace/aviation equipment (2) Transportation equipment (electric trains, ships, etc.) (3) Medical equipment (4) Power-generation control equipment (5) Atomic energy-related equipment (6) Seabed equipment (7) Transportation control equipment (8) Public information-processing equipment (9) Military equipment (1) Electric heating apparatus, burning equipment (11) Disaster prevention/crime prevention equipment (12) Safety equipment (13) Other applications that are not considered general-purpose applications When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing protection circuit/device or providing backup circuits in your equipment.
(3/1) Chip beads For power line Overview of Product compatible with ohs directive Halogen-free Compatible with lead-free solders AEC-Q2 FEATUES Noise reduction solution for power line. Compared to the MM series, has low direct current resistance for compatibility with large currents, optimal for low power consumption. Performs well even in signal lines where low direct current resistance is required. APPLICATION Various ECUs, powertrains, body controls, and car multimedia (telematics). PAT NUMBE CONSTUCTION MP 212 S 11 A T D25 Series name L W T dimensions Impedance Characteristic Material name Packaging style Internal code (mm) ( ) at 1MHz type 212 2. 1.25x.85 S 11 1 A T Taping D25 OPEATING TEMPEATUE ANGE, PACKAGE QUANTITY, PODUCT WEIGHT Type Operating temperature Temperature ranges Package quantity Individual weight Storage temperature C C (pieces/reel) mg MP212 55 to +125 55 to +125 4, 8 The storage temperature range is for after the circuit board is mounted. ohs Directive Compliant Product: See the following for more details.https://product.tdk.com/info/en/environment/rohs/index.html Halogen-free: indicates that Cl content is less than 9ppm, Br content is less than 9ppm, and that the total Cl and Br content is less than 15ppm.
(4/1) ECOMMENDED EFLOW POFILE Preheating Soldering Peak T4 Natural cooling T: Temperature T2 T3 t3 T3 T1 t1 t2 t: Time Preheating Soldering Peak Temp. Time Temp. Time Temp. Time T1 T2 t1 T3 t2 T4 t3 15 C 18 C 6 to 12s 23 C 3 to 6s 25 to 26 C 1s
(5/1) MATEIAL CHAACTEISTIC S material: Standard type that features impedance characteristics similar to those of a typical ferrite core. For signal line applications in which the blocking region is near 1MHz. Impedance values selected for effectiveness at 4 to 3MHz. TYPICAL MATEIAL IMPEDANCE CHAACTEISTICS 25 2 15 1 5 S 1 1 1 Frequency(MHz)
(6/1) SHAPE & DIMENSIONS 2.±.2.85±.2 1.25±.2.5±.3 Dimensions in mm ECOMMENDED LAND PATTEN 1.2.8 1.8 Dimensions in mm
(7/1) ELECTICAL CHAACTEISTICS CHAACTEISTICS SPECIFICATION TABLE Impedance DC resistance ated current Part No. [1MHz] ( ) Tolerance ( )max. (A)max. 3 ±1.1 6 MP212S3ATD25 1 ±25%.2 4 MP212S11ATD25 22 ±25%.4 3 MP212S221ATD25 33 ±25%.5 2.5 MP212S331ATD25 6 ±25%.1 2 MP212S61ATD25 1 ±25%.15 1.5 MP212S12ATD25 Please refer to the graph of rated current vs. temperature characteristics (derating) about the rating current at 85 C or more in temperature of the product. Measurement equipment Measurement item Product No. Manufacturer Impedance E4991A+16192A Keysight Technologies DC resistance Type-7556 Yokogawa Equivalent measurement equipment may be used. ated current vs. temperature characteristics (derating) 7 6 S3A ated current (A) 5 4 3 2 1 S11A S221A S331A S61A S12A 55 35 15 5 25 45 65 85 15 125 Temperature ( C)
(8/1) ELECTICAL CHAACTEISTICS VS. FEQUENCY CHAACTEISTICS (BY SEIES) MP212S series 12 11 MP212S221A 1 MP212S11A 9 MP212S3A 8 7 6 5 4 3 2 1 1 MP212S12A MP212S61A MP212S331A 1 1 1 1
(9/1) ELECTICAL CHAACTEISTICS,, VS. FEQUENCY CHAACTEISTICS MP212S3ATD25 MP212S11ATD25 MP212S221ATD25 5 4 3 2 1 1 1 1 1 1 14 12 1 8 6 4 2 1 1 1 1 1 3 25 2 15 1 5 1 1 1 1 1 MP212S331ATD25 MP212S61ATD25 MP212S12ATD25 4 35 3 25 2 15 1 5 1 1 1 1 1 7 6 5 4 3 2 1 1 1 1 1 1 12 1 8 6 4 2 1 1 1 1 1
(1/1) PACKAGING STYLE EEL DIMENSIONS 2.±.5 ø6min. 1. ø18±2. ø13±.2 ø21±.8 8.4 +2.. 14.4max. Dimensions in mm TAPE DIMENSIONS 1.5 +.1 2.±.5 4.±.1 B 3.5±.5 1.75±.1 8.±.3 A P1 K Dimensions in mm Type A B P1 K MP212 1.5±.2 2.3±.2 4.±.1 1.1max. 16min. Taping 2min. Drawing direction 3min. Dimensions in mm