NewHeights Presidente Reception Assembly Instructions Warranty: raproducts.com/warranty Failure to comply with or observe all assembly, safety, and operation instructions and warnings regarding use of this product may result in serious property damage or bodily injury. Make sure no obstacles are in the desk s path and all cords are of appropriate length for the desk. Always maintain a 1 clearance around the table to prevent pinching. Never assemble (or disassemble) the table or components with the table plugged into a power outlet. This product is for use on a nominal 120-volt circuit and has a grounding plug. Make sure that the product is connected to an outlet having the same configuration as the plug. No adapter should be used with this product. Instruction #53884 Dated: 01//2017
Tools Required for Assembly: Power Driver with Adjustable Torque #2 Phillips Head Driver Bit #2 Square Head Driver Bit 3/16 Hex Head Driver Bit or Allen Wrench May have extra hardware 1 2 3 4 52436 x4 51687 x24 53638 x4 53838 x8 5 6 7 8 51708 x45 50072 x4 52604 x1 52963 x2 9 53900 x4 Grommet Insert x4 K&A Manufacturing 800.298.4351 www.raproducts.com/install 2 of
1 2 5 52436 x4 51687 x24 51708 x8 x4 2 Back Panel (Inside) 1 x4 2 Kick Panel (Inside) 2 2 2 Install levelers x8 Install levelers 1 Left Side Panel Right Side Panel 1 Note: Use Upper Most Pilot Hole 3 5 5 x8 K&A Manufacturing 800.298.4351 www.raproducts.com/install 3 of
Left Side Panel 4 Back Panel Tighten cams to join side panels to back panel. Right Side Panel 5 Slide the weld nuts on the side brackets into the grooves at the front of the columns. K&A Manufacturing 800.298.4351 www.raproducts.com/install 4 of
6 53838 x8 4 51708 x8 5 Grommet Insert x4 3 5 Drive the wood screws #5 into the pilot holes. Then tighten the machine screws #3. Left hand shown. Right hand same. Back Panel 7 4 Kick Panel Tighten camlocks through holes in kick panel. Reversed Direction. Counter Clockwise = Tighten Clockwise = Loosen K&A Manufacturing 800.298.4351 www.raproducts.com/install 5 of
8 Slide the cross braces between the back panel and kick panel under the slim fix bolts. Raise up and engage the bolts into the cams. Tighten the camlocks. 9 Install control box temporarily connect switch, motor cables and power. Lower to lowest position and reset. Raise to highest position and disconnect all cables. Switch Motor Motor Power K&A Manufacturing 800.298.4351 www.raproducts.com/install 6 of
5 6 51708 x31 50072 x4 Modesty Panel 6 5 Install modesty panel, u-channel, control box, switch and switch clip. Power Cable Motor Cable Motor Cable Switch Cable 11 Wiring Diagram 12 End of Control Box Switch Motor Motor Power K&A Manufacturing 800.298.4351 www.raproducts.com/install 7 of
3 5 8 53638 x4 51708 x16 52963 x2 5 13 3 8 14 Loosely install weld nuts and bolts to back side of cross support, slide into short aluminum extrusions. K&A Manufacturing 800.298.4351 www.raproducts.com/install 8 of
9 53900 x4 15 9 Long screw #9 through outer most screw boss. Do not tighten screws until all are installed. Once all screws are installed, tighten four (4) cross support screws and four (4) long screws. Install cross support covers. 16 K&A Manufacturing 800.298.4351 www.raproducts.com/install 9 of
Grommet Insert x2 17 Install divider cover and worksurface grommet insert. 18 Lower table to lowest position to reset. Save for Reference Operation and Reset Procedure If you unplug or lose power and the table does not operate, follow the reset procedure. Reset Procedure: Unplug the power for 30 seconds and plug back in. Hold the down arrow until the unit reaches its lowest point. The control box is now in reset mode. If the workstation leg assemblies are at uneven heights, it usually is caused by an improperly installed hex rod. Disassemble one of the legs and make sure both ends of the hex rod are properly engaged in the hex drives near the tops of the leg assemblies. Troubleshooting: If you are having any problems with the table operation, contact RightAngle service at 800-298-4351 or orders@raproducts.com. K&A Manufacturing 800.298.4351 www.raproducts.com/install of