E Small Tool Instruments and Reference Gages Gage Blocks Height Master Reference Gages Granite Surface Plates & Bench Comparator CERA/Steel Combination Gage Block Sets Step Master ZERO CERA BLOCK Ceramic Straight Master INDEX Gage Blocks E-2-4 Metric Rectangular Gage Block Set E-5,6 Inch Rectangular Gage Block Set E-7 Micrometer Inspection Gage Block Sets E-8 Bore Gage Calibration Kit E-8 Individual Metric Rectangular Gage Block E-, Individual Inch Rectangular Gage Block E- Rectangular Gage Block with CTE E-2 Rectangular Gage Block Accessories E-3-5 Metric Square Gage Block Set E-6 Inch Square Gage Block Set E-7 Individual Metric Square Gage Block E-8 Individual Inch Square Gage Block E- Square Gage Block Accessories E-2,2 Ceraston E-22 Maintenance Kit for Gage Block E-22 Step Master E-23 Made-to-Order Block & Reference E-23 Gage Block Comparator GBCD-25 E-24 Gage Block Comparator GBCD-A E-24 Height Masters Height Master E-25 Digital Height Master E-26 Riser Blocks E-27 Auxiliary Block Kit E-27 Universal Height Master E-28 High-Accuracy Check Master HMC-H E-2 CERA Straight Master SM-C E-3 Square Master E-3 Reference Gages Standard Scales E-32 Working Standard Scales E-32 High-Precision Square E-33 Spring Dividers and Calipers E-33 Combination Square Set E-34 Steel Rules E-35,36 Semi-Flexible Rules E-36 Thickness Gages E-37 Precision Levels E-37 Digital Universal Protractor E-38 Universal Bevel Protractor E-3 Bevel Protractor E-3 Radius Gages E-4 Pitch Gages E-4 Radius Gages-Sets E-4 Digital Protractor E-42 Digital Hand Tachometers E-43 Bench Center E-44 Granite Surface Plate Granite Surface Plate Accessories E-44 Black Granite Surface Plate E-45 Steel Stands E-46 E-
Gage Block SERIES 56 Precision gage blocks are the primary standards vital to dimensional quality control in the manufacture of parts. Mitutoyo offers a complete selection of gage blocks available in a choice of rectangular or square, metric or inch and steel or CERA (ceramic) types. Accuracy Mitutoyo gage blocks guarantee such a high accuracy that users can use them without anxiety. Mitutoyo has established a traceability system for our measurement products, up to the Metrology Management Center of the National Institute of Advanced Industrial Science and Technology (AIST), and we have been certified by the Japanese government as an accredited laboratory. Selecting Gage Blocks Select gage blocks in accordance with the combination range required. If a large length is required, add a long block set. Select gage blocks in accordance with the minimum length step required. Add wear block sets if necessary. If a set containing a large number of gage blocks is selected, the number of combination gage blocks required for a length is reduced and the number of combinations is increased. The accuracy will be retained and damage will be reduced. The specific gage block set for micrometer inspection and caliper inspection is available. If using only one length repeatedly, it is a good idea to purchase discrete gage blocks. The 2mm-based gage blocks, which take the base of the minimum length step as 2mm, are easy to handle and will not warp, as compared to the mm-based gage blocks. Wringing The lapping technique is one of Mitutoyo s specialties. Our advanced lapping technique, developed for more than a half century, allows us to achieve the best flatness and surface roughness needed for gage blocks. Abrasion Resistance and Dimensional Stability High-carbon, high-chrome steel is employed to sufficiently satisfy a variety of material characteristics required for gage blocks. A high degree of hardness, obtained by our heat treatment technology, as well as methodically repeated heat treatment, have successfully reduced deterioration change over time. CERA Blocks CERA blocks, made of ceramic materials with superior surface quality, were developed by Mitutoyo s ultra-precision machining techniques and solve problems commonly associated with steel gage blocks. Rectangular Block Gage Size Face Width (A) Face Depth (B) Up to 2.8.355 Over.2 up to 4.378.355 Up to mm 3mm mm Over mm up to mm 35mm mm. Corrosion-Resistant Anti-corrosion treatment is not required when handled normally (i.e. with fingers), resulting in simple maintenance and storage. 2. No Burrs Caused by Dents, etc. Since the CERA Block is very hard it will not scratch and is highly resistant to burrs. If a burr is formed, it can easily be removed with a (m) ceramic deburring stone (Ceraston). 3. Abrasion Resistant.4 CERA Blocks have times the abrasion resistance of steel gage blocks..2 4. Dimensional Stability CERA Blocks are free from dimensional change over time. 5. Marking The black characters, indicating the nominal length, are inscribed by laser and are clearly visible against the white surface of the block. Abrasion loss Resistance to wear 2 Steel Silicon nitride CERA Block 4 6 8 Amount of travel (m) Tungsten carbide Square Block Gage Size Face Width (C) Face Depth (D) Inch (up to 4 ).5.5 Metric (up to mm) 24.mm 24.mm E-2
Grade and Application Refer to the following table to select the gage block grade according to usage. Applications Grade Workshop use Mounting tools and cutters AS- or AS-2 Manufacturing gages or AS- Calibrating instruments Inspection use Inspecting mechanical parts, or AS- tools, etc. Checking the accuracy of gages or Calibrating instruments Calibration use Checking the accuracy of gage K or blocks for workshop Checking the accuracy of gage blocks for inspection Checking the accuracy of instruments Reference use Checking the accuracy of gage blocks for calibration For academic research K Grade AS-: These gage blocks are intended for shop-floor use to set and calibrate fixtures, as well as precision instruments. Grade : This grade is used within an inspection area to verify the accuracy of plug and snap gages, as well as for setting electronic measuring devices. Grade : These higher accuracy gages are intended for use within a controlled environment by skilled inspection staff. Mainly used as reference standards for setting high-precision measuring equipment and for the calibration of lower grade gage blocks. Grade K: Gage blocks of this accuracy are intended for use within a temperature-controlled inspection room or calibration laboratory. They should be used as masters with certificates against other gage blocks which are calibrated by comparison. Combination of a Required Length Multiple combinations of gage blocks can be used to make a required length. Care should be exercised in the following points.. Use as few gage blocks as possible to obtain the required length. (Select thick gage blocks whenever possible.) 2. Select gage blocks starting with the one that has the least significant digit required, and then work up to ones with more significant digits. 3. There are multiple combinations for the integer part of a length. To prevent wear as much as possible, do not always use the same gage blocks. Example combination Required length = 45.6785mm For the mm-based gage block set (2 pcs.).5.8.7 7.5 + 25 45.6785mm For the 2mm-based gage block set (2 pcs.) 2.5 2.8 2.7 4.5 + 25 45.6785mm 6. Anti-magnetic Nature Keeps Away Steel Powders 7. High Wringing Force An even, dense tissue can maintain a strong wringing force. 8. Material of CERA block Material CERA Block Steel Carbide Silicon nitride Property (ZrO 2) (Fe) (WC-Co) (Si 3N 4) Hardness (HV) 35 8 65 5 Coefficient of thermal expansion ( -6 /K).3±.5.8±.5 5.5±. 2 Flexural strength by 3-point bending (MPa) 27 6 6 58 Fracture toughness Kc (MPa m /2 ) 7 2 2 6.5 Young s Modulus x4 (MPa) 2.6 2.6 6.8 28.4 Poisson s Ratio.3.3.2.3 Specific gravity 6. 7.8 4.8 3.2 Thermal conductivity (W/m k) 2. 54.4 7.5 6.7. Closest Expansion Coefficient to Steel The thermal expansion coefficient of a CERA Block is similar to that of a steel gage block.. Highly Resistant Against Drops and Other Shocks The CERA block material is one of the toughest ceramics materials. It is extremely difficult to crack under normal use. Features of Square Gage Blocks. Perfect wringing is possible using the center hole. After wringing the square gage blocks, an optional tie rod can be inserted through the center hole to fix the blocks using a screw. 2. A height reference standard can easily be made. A precision height reference standard can be made easily and inexpensively using accessories such as the plain jaw and block base. 3. A dedicated inspection jig can be easily made. A dedicated inspection jig for periodic inspection of instruments can be made easily and inexpensively. 4. A wide measuring surface with cross section dimensions of [24. x 24.mm /.5 x.5 ] is available. A square gage block can retain stable orientation both longitudinally and laterally. A wide range of application measurements can be made, including cutting tool positioning, angle measurement with a sine bar, taper measurement with a roller, and inspection of depth micrometers. Long and Ultra-Thin Gage Blocks Mitutoyo offers extra thin gage blocks from. mm to. mm (increments of. mm), as well as long gage blocks up to, mm as standard products. 7 Difference in dimension (m) 3 Silicon nitride 8 2 Tungsten carbide CERA Block 2 2 22 23 Temperature (C) - -2-3 Differences in the dimension between some materials and steel that are obtained when measuring testpieces with a length of mm at each temperature. E-3
Gage Block SERIES 56 Accuracies of Mitutoyo Gage Blocks All Mitutoyo gage blocks meet or exceed all known specifications. The flatness, parallelism and surface finish necessary to achieve the required accuracies are the same as or better than government requirements. ASME (American Society of Mechanical Engineers) Deviations and Tolerance on Length for Metric and inch Gage Blocks: ASME B8..-22 (USA) Nominal Length Range l n in inches Calibration Grade K Grade Grade Grade AS- Grade AS-2 Limit Limit Limit Limit Limit Deviations Deviations Deviations Deviations Deviations of Length Tolerance for of Length Tolerance for of Length Tolerance for of Length Tolerance for of Length at any Point the Variation at any Point the Variation at any Point the Variation at any Point the Variation at any Point From Nominal In Length From Nominal In Length From Nominal In Length From Nominal In Length From Nominal Length tv µin. Length tv µin. Length tv µin. Length tv µin. Length ± te µin. ± te µin. ± te µin. ± te µin. ± te µin. Tolerance for the Variation In Length tv µin. l n.5 2 2 4 2 6 4 2 6 24 2.5 l n.4 2 3 2 5 4 8 6 8 2.45 l n 2 2 3 2 6 4 2 6 24 2 l n 2 6 2 4 2 8 4 6 6 32 2 2 l n 3 2 2 5 3 4 2 6 4 4 3 l n 4 24 3 6 3 2 5 24 8 48 4 4 l n 5 32 3 8 3 6 5 32 8 64 6 5 l n 6 32 3 8 3 6 5 32 8 64 6 6 l n 7 4 4 4 2 6 4 8 6 7 l n 8 4 4 4 2 6 4 8 6 8 l n 48 4 2 4 24 6 48 4 8 l n 2 56 4 4 4 28 7 56 2 2 2 l n 6 72 5 8 5 36 8 72 2 44 2 6 l n 2 88 6 2 6 44 88 4 76 24 2 l n 24 4 6 25 6 52 4 6 2 28 24 l n 28 2 7 3 7 6 2 2 8 24 28 28 l n 32 36 8 34 8 68 2 36 2 26 32 32 l n 36 52 8 38 8 76 4 52 2 3 36 36 l n 4 6 4 8 6 68 24 32 4 Mitutoyo Gage Blocks and Inspection Certificates A Certificate of Inspection is furnished with all Mitutoyo gage blocks with a serial number on the case and an identification number on each block. The deviation of each block is registered. For this inspection, each gage block is measured relative to the upper level master using a gage block comparator. Grade K gage blocks are manufactured by absolute measurement using an interferometer. The gage block set and discrete gage block are supplied with a Certificate of Calibration. The Certificate of Calibration specifies the deviation from the nominal length. (Comparative measurement, however, is performed for all square gage blocks.) Nominal Length Range l n in mm Calibration Grade K Grade Grade Grade AS- Grade AS-2 Limit Limit Limit Limit Limit Deviations Deviations Deviations Deviations Deviations of Length Tolerance for of Length Tolerance for of Length Tolerance for of Length Tolerance for of Length Tolerance for at any Point the Variation at any Point the Variation at any Point the Variation at any Point the Variation at any Point the Variation From Nominal In Length From Nominal In Length From Nominal In Length From Nominal In Length From Nominal In Length Length tv µm Length tv µm Length tv µm Length tv µm Length tv µm ± te µm ± te µm ± te µm ± te µm ± te µm l n.5.3.5..5.4..3.6.6.3.5 l n.2.5.7.5.2..2.6.45.3 l n 25.3.5.7.5.4..3.6.6.3 25 l n 5.4.6..6.2..4.8.8.3 5 l n 75.5.6.2.6.25.2.5.8..35 75 l n.6.7.5.7.3.2.6.2.2.35 l n 5.8.8.2.8.4.4.8.2.6.4 5 l n 2...25..5.6..25 2..4 2 l n 25.2..3..6.6.2.25 2.4.45 25 l n 3.4..35..7.8.4.25 2.8.5 3 l n 4.8.2.45.2..2.8.3 3.6.5 4 l n 5 2.2.4.5.4..25 2.2.35 4.4.6 5 l n 6 2.6.6.65.6.3.25 2.6.4 5..7 6 l n 7 3..8.75.8.5.3 3..45 6..7 7 l n 8 3.4.2.85.2.7.3 3.4.5 6.5.8 8 l n 3.8.2.5.2..35 3.8.5 7.5. l n 4.2.25..25 2..4 4.2.6 8.. A Certificate of Accuracy, traceable to the NIST, is furnished with each gage block set and individual block. Mitutoyo America Corporation Calibration Laboratory: ISO 725-25 accredited calibration available Calibration capability up to mm/4" length Low measurement uncertainty Contact Information: 65 Corporate Blvd. Aurora, Illinois 652 Phone: (888) 648-886 option 7 Fax: (63) 78-6477 E-4
Metric Rectangular Gage Block Set SERIES 56 mm Base Block Set Steel 2-block set Steel 3-block set Steel 47-block set Provided with Inspection Certificate CERA 2-block set CERA 56-block set CERA/Steel combination 47-block set mm Base Block Set Blocks per set Order No. Blocks included in set Steel CERA Grade Size Step Qty. 56-54-56 K.5 56-337-26. -.. 56-338-26. -.4. 4 56-33-26 AS-.5-24.5.5 4 56-34-26 AS-2 25-25 4 2 56-53-56 56-37-26 56-38-26 56-3-26 56-4-26 3 56-533-56 56-4-26 56-42-26 56-43-26 56-44-26 87 56-535-56 56-45-26 56-46-26 56-47-26 56-48-26 56 56-536-56 56-53-26 56-54-26 56-55-26 56-56-26 47 56-537-56 56-57-26 56-58-26 56-5-26 56-6-26 56-542-56 56-34-26 56-342-26 56-343-26 56-344-26 55-543-56 56-345-26 56-346-26 56-347-26 56-348-26 56-544-56 56-353-26 56-354-26 56-355-26 56-356-26 56-545-56 56-357-26 56-358-26 56-35-26 56-36-26 K AS- AS- 2 K AS- AS- 2 K AS- AS-2 K AS- AS-2.5. -.4.5-24.5 25 -. -.. -.4.5 -.5 -.5. -.. -.. -. - 24 25 -.5. -.. -. - 24 25 -..5 25...5... 25.. 25 4 4 4 4 24 4 24 4 E-5
Metric Rectangular Gage Block Set SERIES 56 Long Block Set, Wear Block Set CERA 8-block set Steel 8-block set Provided with Inspection Certificate Long Block Set Blocks per set Order No. Grade Blocks included in set Steel CERA ASME Size Step Qty. 56-547-56 K 25-2 25 8 56-64-26 56-65-26 56-66-26 AS- 8 56-5-26 56-6-26 8 56-54-56 56-7-26 56-72-26 56-73-26 56-546-56 56-73-26 56-732-26 56-733-26 K AS- 25-75 2-25 3-5 25 5 3 2 3 CERA 2-block set Carbide 2-block Wear block 5 mm Wear block Wear Block Set Blocks per set Order No. Grade Blocks included in set Carbide CERA ASME Size Qty. 56-832-26 2 56-833-26 AS- 56-83-26 2 2 56-83-26 AS- 2 56-87-26 56-86-26 2 56-83-26 56-82-26 E-6
Inch Rectangular Gage Block Set SERIES 56 Inch Block Set, Thin Block Set, Long Block Set, Wear Block Set Provided with Inspection Certificate Inch Block Set Blocks per set Order No. Grade Blocks included in set Steel CERA Steel/CERA Size Step Qty. 56-557-56 K... 56-3-26..4. 4 56-32-26 56-32-27**.5.5.5 56-33-26 AS- - 4 4 56-34-26 AS-2 8 56-54-56 56--26 56-2-26 56-3-26 56-4-26 35 56-55-56 56-3-26 56-4-26 56-5-26 56-6-26 56-558-56 56-33-26 56-34-26 56-35-26 56-36-26 K AS- AS-2 ** CERA blocks are adopted for frequently-used blocks. 8-block set: All are CERA blocks, except 2, 3, and 4 are steel blocks.5....... -.3.5,, 2, 4.... 3 4 Thin Block Set Blocks Order No. Grade Blocks included in set per set Steel CERA Size Step Qty. 28 56-55-56 K.25 56-7-26.2.2. 56-8-26 56--26 56-2-26 AS- AS-2.2.2.... 56-26-26 56-27-26 AS-.5 -.5.5 Long Block Set Blocks Order No. Grade Blocks included in set per set Steel CERA Size Step Qty. 8 56-26-26 56-76-26-8 8 56-27-26 56-77-26 AS- 8 56-564-56 K 5-7 3 56-74-26 8,, 2 2 3 56-72-26 56-742-26 6, 2 4 2 56-73-26 56-743-26 AS- Wear Block Set Blocks Order No. Grade Blocks included in set per set Carbide CERA Size Qty. 2 56-8-26 56-836-26.5 2 56-88-26 56-837-26 AS- 2 56-85-26 56-834-26. 2 56-84-26 56-835-26 AS- E-7
Micrometer Inspection Gage Block Sets SERIES 56 Gage blocks for inspecting a variety of micrometers. Can be measured in both vertical and horizontal posture. Parallelism is measured by attaching the optical parallel (optional accessory) to the gage block set. Micro Checker Metric Micro Checker (holder only) Order No. 56-67 Applicable gage 56-6-26, 56-7-26, block set 56-56-26, 56-57-26 Applicable gage 2.5, 5., 7.7,.3, 2., 5, 7.6, block size (mm) 2.2, 22.8, 25 Inch/Metric Micro Checker (holder only) Order No. 56-68 Applicable gage 56-2-26, 56-22-26, block set 56-23-26, 56-32-26, 56-322-26, 56-323-26 Applicable gage block size (inch).5,.2,.35,.42,.5,.65,.85,.2 Metric Block Set Blocks Order No. Grade Blocks included in set per set Steel CERA 56-3-26 56-52-26.,.25,.5, 2, 3, 5,, 5, 2, 25mm 56--26 56-53-26 AS- 56-6-26 56-56-26 2.5, 5., 7.7,.3, 2., 5, 7.6, 2.2, 22.8, 25mm 56-7-26 56-57-26 AS- Optical parallel (t = 2mm) Inch Block Set Blocks Order No. Grade Blocks included in set per set Steel CERA 56-552-56 56-55-56 K 56-2-26 56-32-26 56-22-26 56-23-26 56-322-26 56-323-26 AS-.5,.2,.35,.42,.5,.65,.7,.85,.2, Optical parallel (t =.5") 56-52-26* 56-3-26*.87,.8,.37,.4,.472,.58,.66,.772,.8, " Optical parallel (t =.5") 56-554-56 56-2-26 56-3-26 56-3-26 56-34-26 56-35-26 * For QuantuMike 56-56-56 56-333-26 56-334-26 56-335-26 56-563-56 56-32-26 56-33-26 56-33-26 K AS- K AS-.625,.,.25,.2,.25,.3,.5,, 2 Optical parallel (t =.5").625,.,.25,.2,.25,.3,.5,, 2 (Gage blocks are optional.) Provided with Inspection Certificate Bore Gage Calibration Kit SERIES 56 Blocks per set Order No. Grade Blocks included in set Carbide Size 56-2-26.4,.8,.6,.2,.4,.8,, 2, 3 68 (plain jaw 2 pc. set) and 64 (6mm holder) E-8
Individual Metric Rectangular Gage Block If using only one length repeatedly, it is good practice to purchase discrete gage blocks. Each gage block is supplied with a Certificate of Inspection. Each Grade K gage block of ASME standard is specially supplied with a Certificate of Calibration, which certificates that the gage block was manufactured via interferometry. Suffix Number for Selecting Standard and Certificate Provided ASME Grade Steel, CERA K -56** -52* -53* AS- -54* AS- 2-55* * provided with Inspection Certificate ** provided with Calibration Certificate and Inspection Certificate Example: 682-52.mm gage block in grade. We make custom length gage blocks:.-mm Inspection Certificate Metric Block Length (mm) Order No. Steel CERA. 682. 686.2 686.3 6862.4 6863.5 6822.6 6864.7 6865.8 6866. 6867.2 6823.2 6868.22 686.23 687.24 687.25 6824.26 6872.27 6873.28 6874.2 6875.3 6825.3 6876.32 6877.33 6878.34 687.35 6826.36 688.37 688.38 6882.3 6883.4 6827.4 6884.42 6885.43 6886.44 6887.45 6828.46 6888.47 688.48 68.4 68.5 656 6356.5 682.52 683 Length (mm) Order No. Steel CERA.53 684.54 685.55 686.56 687.57 688.58 68.5 6.6 6.6 62.62 63.63 64.64 65.65 66.66 67.67 68.68 6.6 6.7 6.7 62.72 63.73 64.74 65.75 66.76 67.77 68.78 6.7 62.8 62.8 622.82 623.83 624.84 625.85 626.86 627.87 628.88 62.8 63. 63. 632.2 633.3 634.4 635.5 636 Length (mm) Order No. Steel CERA.6 637.7 638.8 63. 64. 655 6355.2 6552 63552.3 6553 63553.4 6554 63554.5 6555 63555.6 6556 63556.7 6557 63557.8 6558 63558. 655 6355 66 636.5 652 6352. 652 6352.2 6522 63522.3 6523 63523.4 6524 63524.5 6525 63525.6 6526 63526.7 6527 63527.8 6528 63528. 652 6352. 656 6356.2 6562 63562.3 6563 63563.4 6564 63564.5 6565 63565.6 6566 63566.7 6567 63567.8 6568 63568. 656 6356. 657 6357. 657 6357.2 6572 63572.3 6573 63573.4 6574 63574.5 6575 63575.6 6576 63576.7 6577 63577.8 6578 63578. 657 6357 E-
Length (mm) Order No. Steel CERA.2 658 6358.2 658 6358.22 6582 63582.23 6583 63583.24 6584 63584.25 6585 63585.26 6586 63586.27 6587 63587.28 6588 63588.2 658 6358.3 65 635.3 65 635.32 652 6352.33 653 6353.34 654 6354.35 655 6355.36 656 6356.37 657 6357.38 658 6358.3 65 635.4 66 636.4 66 636.42 662 6362.43 663 6363.44 664 6364.45 665 6365.46 666 6366.47 667 6367.48 668 6368.4 66 636.5 664 6364.6 656 6356.7 657 6357.8 658 6358. 65 635 2 662 6362 2.5 66 2. 66 2.2 662 2.3 663 2.4 664 2.5 665 2.6 666 2.7 667 2.8 668 2. 66 2. 67 2.2 672 2.3 673 2.4 674 2.5 675 2.6 676 2.7 677 2.8 678 2. 67 2. 67 2. 67 2.2 672 2.3 673 2.4 674 2.5 675 2.6 676 Length (mm) Order No. Steel CERA 2.7 677 2.8 678 2. 67 2.2 672 2.2 672 2.22 6722 2.23 6723 2.24 6724 2.25 6725 2.26 6726 2.27 6727 2.28 6728 2.2 672 2.3 673 2.3 673 2.32 6732 2.33 6733 2.34 6734 2.35 6735 2.36 6736 2.37 6737 2.38 6738 2.3 673 2.4 674 2.4 674 2.42 6742 2.43 6743 2.44 6744 2.45 6745 2.46 6746 2.47 6747 2.48 6748 2.4 674 2.5 6642 63642 2.6 675 2.7 675 2.8 6752 2. 6753 3 663 6363 3.5 6643 63643 4 664 6364 4.5 6644 63644 5 665 6365 5. 685 6385 5.5 6645 63645 6 666 6366 6.5 6646 63646 7 667 6367 7.5 6647 63647 7.7 685 6385 8 668 6368 8.5 6648 63648 66 636.5 664 6364 667 6367.3 6852 63852.5 665 6365 662 6362.5 665 6365 2 6622 63622 2.5 6652 63652 2. 6853 63853 Length (mm) Order No. Steel CERA 3 6623 63623 3.5 6653 63653 4 6624 63624 4.5 6654 63654 5 6625 63625 5.5 6655 63655 6 6626 63626 6.5 6656 63656 7 6627 63627 7.5 6657 63657 7.6 6854 63854 8 6628 63628 8.5 6658 63658 662 6362.5 665 6365 2 6672 63672 2.2 6855 63855 2.5 666 6366 2 663 6363 2.5 666 6366 22 6632 63632 22.5 6662 63662 22.8 6856 63856 23 6633 63633 23.5 6663 63663 24 6634 63634 24.5 6664 63664 25 6635 63635 25.25 6754 63754 3 6673 63673 35 6755 63755 4 6674 63674 4.3 6857 63857 45 6756 63756 5 6675 63675 6 6676 63676 7 6677 63677 75 68 638 8 6678 63678 667 6367 668 6368 25 682 6382 3.4 6858 63858 5 683 6383 75 684 6384 2 6682 63682 25 685 6385 3 6683 63683 4 6684 63684 5 6685 63685 6 684 7 684 75 6842 8 6843 6844 6845 Metric Wear Block Length (mm) Order No. Tungsten carbide 626 2 6262 DIMENSIONS Nominal length:.mm - 5.5mm Nominal length: 6mm - mm Nominal length:.3mm - mm -.5 -.2 Measuring face Nominal Value Measuring face Serial number -.5 -.2 Measuring face -.5 -.2 Measuring face Nominal length 25mm - mm 35 -.3 x.2 25 ±.5 3 -.3 35 -.3 Nominal Value Airy line -.5 -.2 223 25 mm 223 3 -.3 Length mm 223 mm 223 Length Nominal Value Serial number Length Nominal Value Serial number 2-Ø Serial number Length Unit: mm x.2 25 ±.5 E-
Suffix Number for Selecting Standard and Certificate Provided ASME Grade Steel, CERA K -56** -52* -53* AS- -54* AS-2-55* * provided with Inspection Certificate ** provided with Calibration Certificate and Inspection Certificate Example: 63-52." gage block in grade. We make custom length gage blocks:.4-2" DIMENSIONS Nominal length:.4 -.25 Nominal length:.3-4 Nominal length:.45-4 Nominal length 5-2 -.2.354 -.8.378-.2 Measuring face x.2.84±.2 Inspection Certificate Nominal Value Measuring face Serial number -.2.354 -.8 Measuring face -.2.354 -.8 Measuring face Nominal Value -.2.354 -.8.8-.2.378-.2 Airy line 223 5 223.8-.2 Length mm 223 mm 223 Length Nominal Value Serial number Length Nominal Value Serial number 2-Ø Serial number Length Unit: Inch x.2.84±.2 Individual Inch Rectangular Gage Block Inch Block Length (inch) Order No. Steel CERA.4 634.5 635.6 636.7 637.8 638. 63. 63. 63.2 632.3 633.4 634.5 635.6 636.7 637.8 638. 63.2 632.25 624.2 623.22 6232.23 6233.24 6234.25 6235.26 6236.27 6237.28 6238.2 623.2 632.22 6322.23 6323.24 6324.25 6325.26 6326.27 6327.28 6328.2 632.3 633.3 633.325 (/32) 6 633.32 6332.33 6333.34 6334.35 6335.36 6336.37 6337.38 6338.3 633.4 634.4 634.42 6342.43 6343.44 6344.45 6345.46 6346.46875 (3/64) 62 634.47 6347.48 6348.4 634.5 65 635 Length (inch) Order No. Steel CERA.6 66.625 633 6333.7 67.7825 (5/64) 63 63.8 68. 6.375 (3/32) 64 63. 6 63.25 6 63.5 635 6335.75 62 63. 62 632.2 622 6322.3 623 6323.4 624 6324.5 625 6325.6 626 6326.7 627 6327.8 628 6328. 62 632. 64 634.2 642 6342.3 643 6343.4 644 6344.5 645 6345.6 646 6346.7 647 6347.8 648 6348. 64 634.375 (7/64) 6 632. 65 635. 65 635.2 652 6352.3 653 6353.4 654 6354.5 655 6355.6 656 6356.7 657 6357.8 658 6358. 65 635.2 66 636.2 66 636.22 662 6362.23 663 6363.24 664 6364.25 665 6365.26 666 6366.27 667 6367.28 668 6368.2 66 636.3 67 637.3 67 637.32 672 6372.33 673 6373.34 674 6374.35 675 6375.36 676 6376.37 677 6377.38 678 6378 Length (inch) Order No. Steel CERA.3 67 637.4 68 638.4 68 638.42 682 6382.43 683 6383.44 684 6384.45 685 6385.46 686 6386.47 687 6387.48 688 6388.4 68 638.5 65 635.6 66 636.7 67 637.8 68 638. 6 63.2 62 632.2 622 6322.25 622 6322.3 63 633.35 62 632.35 623 6323.375 (3/8) 63 632.4 64 634.42 62 632.45 624 6324.5 65 635.55 625 6325.6 66 636.65 62 632.65 626 6326.7 67 637.7 622 6322.75 627 6327.8 68 638.85 6226 63226.85 628 6328. 6 63.2 6227 63227.5 62 632 62 632 2 622 6322 3 623 6323 4 624 6324 5 625 6325 6 626 6326 7 627 6327 8 628 6328 6222 63222 2 6223 63223 6 6224 63224 2 6225 63225 Inch Wear Block Length (inch) Order No. Tungsten carbide.5 625. 62 E-
Rectangular Gage Block with CTE Gage Blocks with Thermal Expansion Coefficient Data Mitutoyo offers top-level gage blocks (steel and ceramic) which are superior to K class blocks. Double-faced interferometer (DFI) Comes with a highly accurate thermal expansion coefficient measured with a high-accuracy double-faced interferometer (DFI). The high-accuracy gage block interferometer (GBI) guarantees high dimensional accuracy. Mitutoyo offers rectangular gage blocks, having nominal values from to 5mm Grade: K class in ASME Uncertainty of thermal expansion coefficient:.35 x -6 /K (k = 2) Uncertainty of dimension measurement: 3nm (k = 2), for mm block Suffix Number for Selecting Standard and Certificate Provided ASME Steel, CERA Grade K -5B -5B: provided with JCSS Calibration Certificate and Inspection Certificate Metric Block with CTE Length (mm) Order No. Steel Order No. CERA 668-5B 6368-5B 25 682-5B 6382-5B 5 683-5B 6383-5B 75 684-5B 6384-5B 2 6682-5B 63682-5B 25 685-5B 6385-5B 3 6683-5B 63683-5B 4 6684-5B 63684-5B 5 6685-5B 63685-5B Inch Block with CTE Length (inch) Order No. Steel Order No.CERA 4 624-5B 6324-5B 5 625-5B 6325-5B 6 626-5B 6326-5B 7 627-5B 6327-5B 8 628-5B 6328-5B 6222-5B 63222-5B 2 6223-5B 63223-5B 6 6224-5B 63224-5B 2 6225-5B 63225-5B Inspection Certificate ZERO CERA Blocks Thermal expansion in the temperature range 2±ºC less than /5 that of steel (±.2-6 /K(2ºC)) Almost no secular change both in dimension and coefficient of thermal expansion Complementary ultra-low thermal expansion and high specific rigidity (Young's Modulus/ specific gravity) Metric Blocks Order No. JIS/ISO/DIN BS ASME Length (mm) 67673-6 67673-6 67673-56 3 67675-6 67675-6 67675-56 5 6768-6 6768-6 6768-56 67682-6 67682-6 67682-56 2 67683-6 67683-6 67683-56 3 67684-6 67684-6 67684-56 4 67685-6 67685-6 67685-56 5 6784-6 6784-6 6784-56 6 6784-6 6784-6 6784-56 7 67843-6 67843-6 67843-56 8 67844-6 67844-6 67844-56 67845-6 67845-6 67845-56 56-77-6 56-77-6 56-77-66 Above set E-2
Rectangular Gage Block Accessories SERIES 56 For Gage Blocks over mm Specially designed for long gage blocks over mm, which have two holes on the body for coupling. 56-65 Accessories for gage blocks over mm Order No. 56-65 Included in set pc. Holder A (63) pc. Holder B (632) pc. Holder C (633) pc. Holder D (634) pc. Holder E (635) 3 pcs. Adaptor (636) pc. Holder base 35mm (6) 2 pcs. Half round jaw 2mm (63) pc. Plain jaw (2 pc. set) (68) pc. Scriber point (6) Note: These accessories can be used for inch rectangular gage blocks. Holder A: 63 Used for coupling two long gage blocks. Fixed pin 75 Adjustable pin 27.5 Holder B and C: Used for coupling two long gage blocks together with other gage blocks up to 35mm (Holder B) or 4mm (Holder C). Also used for attaching jaws with two adapters. Order No. R (max.) L Holder B 632 mm 26mm Holder C 633 2mm 236mm L R Holder D: 634 Used for attaching to the holder base. Holder E: 635 Used for attaching to the holder base together with other gage blocks up to 25mm. Used for attaching jaws with one adapter. 4 65.5 7-75 2 Half-round jaw: 63 Holder base: 6 Adaptor: 636 35±.8 Holder mount Finished surface 2±.5mm 25 Measuring face Finished surface 75 3 Scriber point: 6 Plain jaw: 68 (2 pc. set) 5 2 6 2 Finished surface 8.5 Finished surface E-3
Rectangular Gage Block Accessories SERIES 56 To expand the variety of rectangular gage block (steel and CERA) applications, Mitutoyo offers the gage block accessories set. By assembling the items in the set, you can easily and quickly build up a precision measuring instrument. 56-6 56-62 Assortment of Accessories Order No. Accessories Metric Set Order No. Accessory (s) 56-6 56-62 included in a set 62 Holder 6mm pc. 63 Holder mm pc. 64 Holder 6mm pc. 65 Holder 25mm pc. 6 Holder Base 35mm pc. 6 Half round jaw 2mm 2 pcs. 6 Half round jaw 5mm 2 pcs. 62 Half round jaw 8mm 2 pcs. 63 Half round jaw 2mm 2 pcs. 64 Half round jaw 2mm 2 pcs. 68 Plain jaw (2 pc. set) 6mm pc. 6 Scriber point pc. 62 Center point pc. 62 Tram point 2 pcs. 622 Triangular straightness edge mm pc. 623 Triangular straight edge 6mm pc. Total Qty. in set 22 pcs. 4 pcs. E-4
Rectangular Gage Block Accessories Holder: Used as a clamp if using plain jaws, scriber point, etc. L Holder base 35mm: 6 Measures a height on the surface plate and scribes a workpiece if used with the holder. Finished surface Finished surfaces A L Clamp Holder mount Finished surface Adapter Finished surface Order No. A 6 35±.5mm Order No. L 62 5-6mm 63 4-6mm 64 62-65mm 65 53-256mm Scriber point: 6 Scribes a workpiece if used with the holder and holder base. mm 5mm Finished surface 8.5mm Center point: 62 Scribes a workpiece if used with the holder and holder base. mm 8.5mm Finished surface 5mm 6 Tram point: 62 Inspects the scale of the height gage, etc., if used with the holder and holder base. mm 8.5mm Finished surface 5mm 3 Plain jaw: 68 Measures an outside or inside diameter if used with a pair of jaws and the holder. 2 Triangular straight edge: Measures parallelism. A 2 L Finished surface 6 L 6 A Order No. L 68* 6mm * 2 pc. set Order No. L 622 mm 623 6mm Half-round jaw: Measures an outside or inside diameter if used with a pair of jaws and the holder. mm H A B C Order No. H A B C 6 2±.5mm 6mm 4mm 8mm 6 5±.5mm 6mm 5mm 8mm 62 8±.5mm 2mm 6mm 8mm 63 2±.5mm 25mm 75mm 3mm 64 2±.5mm 25mm 25mm 2.5mm mm A B H C E-5
Metric Square Gage Block Set SERIES 56 Metric Block Set, Long Block Set, Wear Block Set A square gage block can retain stable orientation both longitudinally and laterally. A wide range of application measurements can be made, including cutting tool positioning, angle measurement with a sine bar, taper measurement with a roller, and inspection of depth micrometers. Steel 32-block set Steel 76-block set Steel 3-block set Steel 2-block set Metric Block Set Blocks Order No. Grade Blocks included in set per set Steel CERA Size Step Qty. 2 56-437-26.5 56-438-26. -.. 56-43-26 56-44-26 AS- AS-2. -.4.5-24.5 25 -..5 25 4 4 4 3 56-44-26 56-442-26 56-443-26 56-444-26 76 56-44-26 56-45-26 56-45-26 56-452-26 47 56-457-26 56-458-26 56-45-26 56-46-26 32 56-465-26 56-466-26 56-467-26 56-468-26 AS- AS-2 AS- AS-2 AS- AS-2 AS- AS-2.5. -.4.5-24.5 25 -.5. -.4.5 -.5-4 5 -.5. -.. -. - 24 25 -.5. -.. -. - - 3 6..5 25..5 25.. 25.. 4 4 4 4 4 3 24 4 3 Metric Long Block Set Blocks Order No. Grade Blocks included in set per set Steel CERA Size Step Qty. 8 56-75-26 25, 5, 75 25 3 56-752-26 2, 25 5 2 56-753-26 56-754-26 AS- AS-2 3, 4, 5 3 Metric Wear Block Set Blocks Order No. Grade Blocks included in set per set Carbide CERA Size Step Qty. 2 56-82-26 2 56-82-26 AS- Provided with Inspection Certificate E-6
Provided with Inspection Certificate Inch Square Gage Block Set SERIES 56 Inch Block Set, Long Block Set, Wear Block Set Inch Block Set Blocks per set Order No. Grade Blocks included in set Steel CERA Size Step Qty. 56-2-26. -.. 56-22-26. -.4. 4 56-23-26 AS-.5 -.5.5 56-24-26 AS-2-4 4 8 56-4-26 56-42-26 56-43-26 56-44-26 36 56-42-26 56-422-26 56-423-26 56-424-26 28 56-47-26 56-48-26 56-4-26 56-42-26 56-22-26 56-222-26 56-223-26 56-224-26 AS- AS-2 AS- AS-2.5. -.. -.. -.. -.5, 2, 4.25.2 -.2.2 -.2.2 -.2. -........ 5 3 Steel 47-block set Inch Long Block Set Blocks Order No. Grade Blocks included in set per set Steel CERA Size Step Qty. 8 56-762-26 56-763-26 AS- 5-7 8,, 2 6, 2 2 4 3 3 2 Inch Wear Block Set Blocks Order No. Grade Blocks included in set per set Carbide CERA Size Step Qty. 2 56-824-26 56-846-26.5 2 56-825-26 56-847-26 AS- 2 56-826-26 56-844-26. 2 56-827-26 56-845-26 AS- Steel 8-block set Carbide 2-block set 2 pcs. Gage Blocks with accessories set in wooden box Blocks in set Order No. Grade Blocks included in set Individual No. Description Qty. Steel Size Step Qty 2 56-45-26.625 652 Plain Jaw.5 2.7825 65 Half round jaw.25 2.375 655 Holder base.5.25 657 Flat head screw /4 2.5 658 Flat head screw 5/8 2.75 656 Stud 2.375 666 Knurled head screw 2. -.. 65 Slotted head nut 2. -.4. 4 662 Tie rod 3.5 -.5.5 4 663 Tie rod 2 /4.6 -.. 664 Tie rod /2 4 4 665 3/4 E-7
Individual Metric Square Gage Block Suffix Number for Selecting Standard and Certificate Provided ASME Grade Steel K -52* -53* AS- -54* AS-2-55* * provided with Inspection Certificate Metric Block Length (mm) Order No. Steel CERA.5 6456 646.5 6452. 6452.2 64522.3 64523.4 64524.5 64525.6 64526.7 64527.8 64528. 6452. 6456.2 64562.3 64563.4 64564.5 64565.6 64566.7 64567.8 64568. 6456. 6457. 6457.2 64572.3 64573.4 64574.5 64575.6 64576.7 64577.8 64578. 6457.2 6458.2 6458.22 64582.23 64583.24 64584.25 64585.26 64586.27 64587.28 64588.2 6458.3 645.3 645.32 6452 Length (mm) Order No. Steel CERA.33 6453.34 6454.35 6455.36 6456.37 6457.38 6458.3 645.4 646.4 646.42 6462.43 6463.44 6464.45 6465.46 6466.47 6467.48 6468.4 646.5 6464.6 6456.7 6457.8 6458. 645 2 6462 2.5 64642 3 6463 3.5 64643 4 6464 4.5 64644 5 6465 5.5 64645 6 6466 6.5 64646 7 6467 7.5 64647 8 6468 8.5 64648-646.5 6464 6467.5 6465 6462.5 6465 2 64622 2.5 64652 Length (mm) Order No. Steel CERA 3 64623 3.5 64653 4 64624 4.5 64654 5 64625 5.5 64655 6 64626 6.5 64656 7 64627 7.5 64657 8 64628 8.5 64658 6462.5 6465 2 64672 2.5 6466 2 6463 2.5 6466 22 64632 22.5 64662 23 64633 23.5 64663 24 64634 24.5 64664 25 64635 3 64673 4 64674 5 64675 6 64676 75 648 6468 25 6482 5 6483 75 6484 2 64682 25 6485 3 64683 4 64684 5 64685 Metric Wear Block Length Order No. (mm) Tungsten carbide 656 2 6562 Example: 646-52 mm gage block in grade. We make custom length gage blocks:.5-5mm. Inspection Certificate E-8
Suffix Number for Selecting Standard and Certificate Provided Individual Inch Square Gage Block ASME Grade Steel, CERA K -52* -53* AS- -54* AS-2-55* * provided with Inspection Certificate Example: 643-52." gage block in grade. We make custom length gage blocks:. - 2" DIMENSIONS Nominal length:.5mm - 4.5mm (." -.") Nominal Value Measuring face Serial number 6.7±. (.264 ).2 Inspection Certificate 24.±. (.5 ). 223 Nominal length: 5mm - 4.5mm (.2" -.45") Nominal Value 6.7±. (.264 ) IN 223 223 24.±. (.5 ) Nominal length: 5mm - 5mm (.5" - 2") Nominal Value Serial number 24.±. (.5 ) Length 24.±. (.5 ) 24.±. Length (.5 ) Measuring face Length 24.±. (.5 ) Measuring face (.264 ) Serial number Unit: mm 6.7±. On both sides 77±2 Ø.3 77±2 Ø.3 Inch Block Length (inch) Order No. Steel CERA. 643.25 6424.2 6423.22 64232.23 64233.24 64234.25 64235.26 64236.27 64237.28 64238.2 6423.2 6432.2 6432.22 64322.23 64323.24 64324.25 64325.26 64326.27 64327.28 64328.2 6432.3 6433.325 (/32) 643.4 6434.46875 (3/64) 6432.5 645 665.6 646.625 6433 6633.7 647.7825 (5/64) 6434.8 648. 64.375 (3/32) 6435. 64 66.25 6437.5 6435 6635.75 6438. 642 662.2 6422 6622.3 6423 6623.4 6424 6624.5 6425 6625.6 6426 6626.7 6427 6627.8 6428 6628. 642 662. 644 664.2 6442 6642.3 6443 6643.4 6444 6644.5 6445 6645 Length (inch) Order No. Steel CERA.6 6446 6646.7 6447 6647.8 6448 6648. 644 664.375 (7/64) 6436. 645 665. 645 665.2 6452 6652.3 6453 6653.4 6454 6654.5 6455 6655.6 6456 6656.7 6457 6657.8 6458 6658. 645 665.2 646 666.2 646 666.22 6462 6662.23 6463 6663.24 6464 6664.25 6465 6665.26 6466 6666.27 6467 6667.28 6468 6668.2 646-666.3 647 667.3 647 667.32 6472 6672.33 6473 6673.34 6474 6674.35 6475 6675.36 6476 6676.37 6477 6677.38 6478 6678.3 647 667.4 648 668.4 648 668.42 6482 6682.43 6483 6683.44 6484 6684.45 6485 6685.46 6486 6686.47 6487 6687.48 6488 6688.4 648 668.5 645 665.6 646 666.7 647 667.8 648 668. 64 66.2 642 662 Length (inch) Order No. Steel CERA.25 6422 6622.3 643 663.35 6423 6623.375 (3/8) 643.4 644 664.45 6424 6624.5 645 665.55 6425 6625.6 646 666.65 6426 6626.7 647 667.75 6427 6627.8 648 668.85 6428 6628. 64 66.5 642 662 642 662 2 6422 6622 3 6423 6623 4 6424 6624 5 6425 6 6426 7 6427 8 6428 64222 2 64223 6 64224 2 64225 Inch Wear Block Length Order No. (inch) Tungsten carbide.5 655. 65 E-
Square Gage Block Accessories SERIES 56 To expand the variety of square gage block applications, Mitutoyo offers the gage block accessories set. By assembling the items in the set, you can easily and quickly build up a precision measuring instrument. 56-6 Metric Order No. 56-6 Included in set 2 pcs. Half round jaw 2mm (67) 2 pcs. Half round jaw 5mm (67) 2 pcs. Plain jaw (672) pc. Center point (673) pc. Scriber point (654) pc. Block base (674) 2 pcs. Flat head screw /4" (657) 2 pcs. Flat head screw 5/8" (658) 2 pcs. Slotted head nut (65) 2 pcs. Adjustable tie rod 6" (66) 2 pcs. Adjustable tie rod 4 /2" (66) pc. Tie rod 3" (662) pc. Tie rod 2 /4" (663) pc. Tie rod /2" (664) pc. Tie rod 3/4" (665) 2 pcs. Stud (656) 2 pcs. Knurled head screw (666) Inch Order No. 56-62 Included in set 2 pcs. Half round jaw.25" (65) 2 pcs. Half round jaw.25" (65) 2 pcs. Plain jaw (652) pc. Center point (653) pc. Scriber point (654) pc. Block base (655) 2 pcs. Flat head screw /4" (657) 2 pcs. Flat head screw 5/8" (658) 2 pcs. Slotted head nut (65) 2 pcs. Adjustable tie rod 6" (66) 2 pcs. Adjustable tie rod 4 /2" (66) pc. Tie rod 3" (662) pc. Tie rod 2 /4" (663) pc. Tie rod /2" (664) pc. Tie rod 3/4" (665) 2 pcs. Stud (656) 2 pcs. Knurled head screw (666) E-2
Half round jaw: Used to measure an inside or outside diameter. Stud: 656 6 R L ø6.7 24.7 W H Finished surface Flat head screw Ø4.66 P=.738 No.8-32UNC Order No. R L W H 67.5mm 2mm 33.6mm 5.3mm 67 4.5mm 5mm 3.mm.3mm 65.23.25 33.6mm 5.3mm 65.248.25 3.mm.3mm Plain jaw: 672 (mm), 652 (.5") Used to measure an inside or outside diameter. L No.8-32UNC d=4.66 P=.738 Order No. L 657 3.6mm 658 5.8mm 24.7 Finished surface ±. 3. ø6.7 Finished surface Slotted head nut: 65 ø6.35 5.8 No.8-32UNC d=4.66 P=.738 Center point: 673 (2mm), 653 (.") Used to scribe a workpiece. Knurled head screw: 666 2 3 24.7 2±. ø6.7 3. 7.8 Finished surface ø No.8-32UNC d=4.66 P=.738 Scriber point: 654 Used to scribe a workpiece. 7.5µm or less 3. 24.7 5.4 Tie rod L No.8-32UNC d=4.66 P=.738 ø6.35 Stud bolt ø6.7 Finished surface Base: 674 (mm), 655 (.5") Used as clamps by inserting them into the center hole of a square gage block. ø6.7 Finished surface 58 Finished surface ±.5 Adjustable tie rod P Order No. L 665 mm 664 38mm 663 57mm 662 76mm ø6.35 n (number of holes) L No.8-32UNC d=4.66 P=.738 Order No. L P n 66 24.5mm 6.35mm 4 66 86.5mm 6.35mm 8 E-2
Ceraston Accessory for Gage Blocks Alumina-ceramic grinding stone for removing burrs from hard materials such as ceramics that ordinary grinding stones cannot handle. Can be used both for steel gage blocks and CERA Blocks. Order No. Dimensions (W x D x H) Mass 6645 x 25 x 2mm g 6644 5 x 5 x 2mm 53g 6644 6645 Removing burrs () Wipe any dust and oil films from the gage block and the Ceraston (or Arkansas stone) using a solvent. (2) Place the gage block on the Ceraston so that the measuring face that has burrs is on the abrasive surface of the stone. While applying light pressure, move the gage block to and fro about ten times (Fig. ). Use a block rubber for thin gage blocks to apply even pressure (Fig. 2). (3) Check the measuring face for burrs with an optical flat. If the burrs have not been removed, repeat step (2). If burrs are too large, they may not be removed with a grinding stone. If so, discard the gage block. Maintenance Kit for Gage Blocks SERIES 56 Includes all necessary maintenance tools for daily care and storage of gage blocks. Supplied in a fitted wooden case for portable use. CERASTON (Arkansas stone) Rubber CERASTON (Arkansas stone) Note: The abrasive surface of a Ceraston must be made flat by lapping it from time to time. After lapping the Ceraston, the lapping powder must be completely removed from the surface to prevent the surface of the gage block from being scratched. Mitutoyo does not carry the Arkansas stone. 56-65E Order No. Assortment of tools and accessories 56-65E Ceraston (6645): Used for removing burrs on the measuring surface. Optical flat (58-7): Used for checking whether burrs exist. Tweezers (64): Used for handling thin gage blocks. Blower brush (65): Used for blowing out dust on the measuring surface. Cleaning paper (66): Used for wiping off rust preventive oil and contamination. Artificial leather mat (67): Used as a gage block mat. Reagent bottle (68): Bottle of wiping solution (ml) Gloves E-22
Step Master SERIES 56 Step master is a master gage used for the z-axis (vertical direction) calibration of optical instruments. Each adjacent step is measured down to.µm by using a interferometer within ±.2µm allowance. Steel and ceramic types are available. Dimension Block No. 2 3 4 5 3 5 2 µm 7 7 7 7 7 45 5 25 Adjacent step 6 (Max. height) R Magnified view of step 56-48 Ceramic type 56- Steel type Metric Order No. Step value between adjacent blocks Remarks No. - No. 2 No. 2 - No. 3 No. 3 - No. 4 No. 4 - No. 5 56-8 µm 5µm 2µm µm Steel type 56-3µm µm 5µm 2µm Steel type 56-48 µm 5µm 2µm µm Ceramic type 56-4 3µm µm 5µm 2µm Ceramic type Made-to-order Block & Reference Available Dimension Nominal size:.4 to 2 /. to mm (steel). to 2 /.5 to 5mm (ceramic) Nominal pitch:.5mm (up to mm).mm (over mm) Minimum section dimension: Approx..24 x.24 / 6 x 6mm Maximum section dimension: Approx. 5.5 x 5.5 / 4 x 4mm (steel) Approx. 6.3 Dia. / ø6mm (steel, cylindrical) Approx. 3.4 x.7 / x 5mm (ceramic) Approx..24 Dia. / ø6mm (ceramic, cylindrical) Accuracy: Gage Block Grade level Special materials of low expansion glass and low expansion ceramic are available. Mitutoyo can provide gage blocks and reference gages to your size and design. A G E H A: Ceramic rectangular gage block (2.4mm) B: Ceramic square gage block (2.5mm) C: Steel square gage block (.72mm) D: Steel square gage block (2.265mm) E: Ceramic rectangular gage block (2.64mm) F: Steel rectangular gage block (3.5mm) G: Ceramic rectangular gage block (6.34mm) H: Steel rectangular gage block (3.63mm) I: Steel rectangular gage block (.55mm) J: Steel rectangular gage block (.555mm) K: Steel rectangular gage block (6.56mm) L: Steel rectangular gage block (.64mm) M: Steel rectangular gage block (.2mm) B I F J C D K M L R O: Steel long rectangular block (5 x x 2mm) P: Ceramic square block (24. x 24. x 2.3mm) Q: Steel thin rectangular block (3 x 6 x.mm) R: Steel square block ( x x 6mm) S: Steel thin rectangular block (3 x 6 x 2.mm) T: Steel cylindrical bock (ø3.8 x 2mm) V O S Q U: Cylindrical reference block for depth micrometer (ø6 x 5mm) V: Ceramic reference plate (5 x 5 x 5mm, flatness.3µm) W: Ceramic stepped block (3 x 8 x 5mm, step:.5mm) T P W U E-23
Gage Block Comparator GBCD-25 SERIES 565 Manual Comparator with Dual Gage Heads Gage blocks between.mm and 25mm easily can be compared with the standard gage block on the GBCD-25. The differential dual gaging heads assure the operator of a high-accuracy measurement with ease of use. Optional Accessories 62723: Gage head calibration kit 2ASD3: Square gage block holder kit 2ASF4: Heat protection shield 2ASQ53: GBPAK-M (Included Software) 377T: Foot Switch 3637: Connecting cable Inch/Metric Model No. GBCD-25 Order No. 565-5A Range.mm - 25mm /.4 - " Resolution.mm(.µm)/.in(.µin) Accuracy in narrow range (2 C) ±(.3+.3L/)µm* L = Gage block length (mm) Measuring units Laser Hologage (upper), Mu-checker (lower) Operating condition Temperature: 2 C ± C Humidity: 58%RH ±5%RH Data output Via SPC output port Dimensions (W x D x H) Main unit: 455 x 38 x 6mm Display unit: 345 x 37 x 87mm Mass Main unit: Approx. 5kg Display unit: Approx. kg * 5% confidence interval (not including the calibration error of the standard gage block). Gage Block Comparator GBCD-A SERIES 565 Automatic-Type Comparator with Dual Gage Heads Model No. GBCD-A Order No. 565-6A Resolution.mm (.µm) /." Range.5mm - mm /.2-4" Measuring unit Differential (dual-head) type Mu-Checker Accuracy in narrow range (2 C) ±(.3+.3L/)µm* L = Gage block length (mm) Measuring force Upper gage head: N (gf) Lower gage head:.6n (6gf) Air requirement 4kPa (4kgf/cm 2 ) Operating condition Temperature: 2 C ± C Humidity: 58%RH ±5%RH Dimensions (W x D x H) Main unit: 7 x 366 x 783mm Electronic unit: 6 x 4 x 382mm Mass Main unit: 2kg Electronic unit: 4kg * 5% confidence interval (not including the calibration error of the standard gage block). The GBCD-A Automatic Gage Block Comparator is an easy-to-operate dualhead gage block inspecting system. It automatically compares workpieces with a standard gage block and determines accuracies such as central length, maximum length, minimum length and parallelism through the operation of an optional personal computer. Standard Accessories GBPAK-A (software) Optional Accessories 56-46-E: Gage block set for GBCD calibration E-24
Technical Data Graduation:." or.mm Counter Resolution:. or.mm Character Height:.6" / 4mm Micrometer Head Travel stroke: or 2mm Pitch:.25 /rev or.5mm/rev Hysteresis:.4 or µm Provided with inspection certificate. Standard Accessories Reference Block: mm for 55-322 Reference Block:.3" for 55-3, 55-3 Optional Accessories 55-2: Auxiliary block kit for bore gage (mm) 55-: Auxiliary block kit for bore gage (for 55-3) 55-2: Auxiliary block kit for bore gage (for 55-3) : Riser block Height Master SERIES 55 Models with staggered arrangement of block stack have two measuring faces on the same level, one facing up and the other down (except for 55-3). Each height master is supplied with a gage block for zero-setting. Supplied in fitted wooden case. Staggered 2mm blocks (movable) Vertical orientation Reading 2 3 55-322 55-3 Riser block A A Height A. Scale 28. mm 2. Counter 5.67 mm 3. Thimble. mm 285.67 mm Metric Range (H) Order No. Block step Graduation Block Pitch Parallelism Micrometer Head Mass (kg) Accuracy of Block Accuracy 5 < H 3mm 55-322 2mm (staggered).mm ±.5µm µm ±µm 23 Inch Range (H) Order No. Block step Graduation Block Pitch Parallelism Micrometer Head Mass (kg) Accuracy of Block Accuracy.2 < H 2.2 55-3.5 (straight). ±.5.4 ±.5 23.2 < H 2.2 55-3 (staggered). ±.5.4 ±.5 23 E-25
Digital Height Master SERIES 55 Standard model with a digital display, featuring all essential specifications required for versatile height standard. With SPC output. Each height master is supplied with a gage block for zero setting. Technical Data Resolution (LCD): Graduation: Character Height." or.mm." or.2mm.2" / 5.4mm Micrometer Head Travel Stroke: Pitch: Hystersis: " or 2mm.25"/rev or.5mm/rev." for all inch models.2mm for 3mm models.25mm for 45 & 6mm models Battery: SR44 (2 pcs.), 38882 Battery life: Approx..8 years under normal use Staggered 2mm blocks (movable) Vertical orientation Riser block Function Zero-setting, Presetting, ABS/INC switching, Data hold, Data output, inch/mm conversion (on inch/metric models only) Alarm: Low voltage, Counting value composition error Standard Accessories Reference Block: mm for Metric Height Master 662-3 Reference Block:.6" for for Inch Height Master 66-53 Provided with inspection certificate. Optional Accessories 55-: Auxiliary block kit for bore gage (mm) 55-2: Auxiliary block kit for bore gage (inch) : Riser block (see page E-27.) 54: SPC cable (4 / m) 55: SPC cable (8 / 2m) 5: Fitted mahogany case for 2 / 3mm model 55: Fitted mohogany case for 8 / 45mm model 24" / 6mm model 55-374 Metric Range (H) Order No. Block step Resolution Block Pitch Accuracy Parallelism Micrometer Head Mass (kg) Accuracy < H 3mm 55-374 2mm (staggered).mm ±.5µm 2µm ±2µm.5 < H 46mm 55-376 2mm (staggered).mm ±2.5µm 2.5µm ±2µm 3.6 < H 6mm 55-378 2mm (staggered).mm ±3.5µm 2.5µm ±2.5µm 6. Inch/Metric Range (H) Order No. Block step Resolution Block Pitch Accuracy Parallelism Micrometer Head Mass (kg) Accuracy.5 < H 2 55-375 (staggered). / ±..5 ±..5.mm.5 < H 8 55-377 (staggered). / ±.. ±. 3.6.mm.5 < H 24 55-37 (staggered). /.mm ±.. ±. 6. E-26
Riser Blocks SERIES 55 These riser blocks are specially designed for standard/digimatic height masters. 55-3 55-4 55-5 Metric Height Order No. Accuracy of height Mass (kg) 5mm 55-3 ±.6µm 5.7 3mm 55-4 ±.µm.3 6mm 55-5 ±2.µm 3 Inch Height Order No. Accuracy of height Mass (kg) 6 55-6 ±2µin 5.7 2 55-7 ±4µin.3 24 55-8 ±8µin 3 Auxiliary Block Kit SERIES 55 for Bore Gage Used for efficient zero-setting of dial bore gages and tubular inside micrometers (8-5mm) on a Height Master. Bore gage zero-setting 55-2 Metric Order No. Applicable height master 55- Universal Height Master 55- Digimatic Height Master 55-2 Height Master Inch Order No. Applicable height master 55- Universal Height Master, Height Master (55-3) 55-2 Digimatic Height Master 55-2 Height Master (55-3) E-27
Universal Height Master SERIES 55 Use in Vertical and Horizontal Orientation The Universal Height Master is designed for both vertical and horizontal orientations, providing a wide range of applications, such as accuracy checking of machine tool table movements. Fitted wooden case supplied. Single-row mm blocks (movable) Technical Data Graduation:.mm or." Counter Resolution:. or.mm Character Height:.6 / 4mm Block arrangement: Straight arrangement Micrometer Head Travel stroke: Pitch: Hysteresis: " or 2mm.25"/rev or.5mm/rev.4 /.2µm up to 24.2 / 6mm.6 /.5µm for 4.2 / mm Block pitch accuracy: ±.5µm ( < R 3mm) ±2.5µm (3 < R 6mm) ±3.5µm (6 < R mm) Parallelism of blocks:.µm ( < R 3mm) 2.5µm (3 < R mm) Provided with inspection certificate. Optional Accessories 574*: Supporting base for vertical operation Mass: 3kg (*supplied as a standard for 55-523 and 55-53) 55-2: Auxiliary block kit for bore gage (mm) 55-: Auxiliary block kit for bore gage (inch) Vertical orientation Horizontal orientation Riser block Using in horizontal orientation 55-52 Metric Range (R) Order No. Block step Graduation Block Pitch Parallelism Micrometer Mass (kg) Accuracy of Block Head Accuracy 5 < R 6mm 55-52 mm (straight).mm ±.5µm.µm ±.2µm 42 5 < R mm 55-523 mm (straight).mm ±3.5µm 2.5µm ±.5µm 63.5 Inch Range (R) Order No. Block step Graduation Block Pitch Parallelism Micrometer Mass (kg) Accuracy of Block Head Accuracy.2 < R 8.2 55-52.5 (straight). ±.5.6 ±.4 42.2 < R 24.2 55-5.5 (straight). ±..6 ±.4 5.2 < R 4.2 55-53.5 (straight). ±.5.8 ±.6 63.5 Supporting base E-28
Technical Data Measuring range (R): Refer to the list of specifications. Block pitch accuracy: ±.2µm ( < R 3mm) ±.8µm (3 < R 6mm) ±2.5µm (6 < R mm) ±4.µm ( < R 5mm) Parallelism of blocks:.µm ( < R 45mm).5µm (45 < R mm 2.µm ( < R 5mm) Provided with inspection certificate. High-Accuracy Check Master HMC-H SERIES 55 Designed to check the accuracy of table movements of machine tools and calibrate CMMs. Permanently wrung stack of gage blocks is housed in a rigid frame. Can be used in either vertical and horizontal orientation. Fitted wooden case supplied. Single-row mm (.5") blocks Vertical orientation Horizontal orientation Specifications for Ceramic Check Master: Each measuring block is made of zirconiabased ceramic that requires no anti-corrosion treatment for measuring faces. Free from deterioration and dimensional changes over time. 55-743 55-742 55-74 Metric Range (R) Order No. Pitch Accuracy of block pitch for the range shown below as measured from the bottom block Length Parallelism Mass (kg) Steel Ceramic P P up to 3mm 3-6mm 6- mm - 5mm 3mm 55-74 55-76 2mm mm ±.2µm 33mm µm 3.6 45mm 55-74 55-76 2mm mm ±.2µm ±.8µm 482mm µm 5.4 6mm 55-742 55-762 2mm mm ±.2µm ±.8µm 63mm.5µm 7.2 mm 55-743 55-763 2mm mm ±.2µm ±.8µm ±2.5µm 37mm.5µm 2. 5mm 55-744 55-764 2mm mm ±.2µm ±.8µm ±2.5µm ±4.µm 546mm 2µm 8. Optional Accessories 667: Supporting base for vertical operation (*supplied as a standard for 55-523 and 55-53) Dimensions: Mass: 4.2"(W) x 8.7"(D) x 8.3"(H) 36mm(W) x 22mm(D) x 2mm(H) 3kg Inch Range (R) Order No. Pitch Accuracy of block pitch for the range shown below as measured from the bottom block Length Parallelism Mass (kg) Steel Ceramic P P up to 2 2-24 24-4 4-6 2 55-73 55-75.5 ±5µin 3. 4µin 3.4 8 55-73 55-75.5 ±5µin ±7µin. 4µin 5.2 24 55-732 55-752.5 ±5µin ±7µin 25. 6µin 6. 4 55-733 55-753.5 ±5µin ±7µin ±µin 4. 6µin.5 6 55-734 55-754.5 ±5µin ±7µin ±µin ±58µin 6.5 8µin 7.3 Size Plate Indicates instrumental errors at intervals of "/2mm +.5 +.2 3 4 5 (Example) Supporting base Side P P 3.2" (8mm) Base P." (5mm) A Zero point Note: 3mm, 2" models do not have hand hold openings. P E-2
CERA Straight Master SM-C SERIES 3 Straightness Measuring Instrument CERA Straight master is a master gage used for the straightness inspection of each axis movement such as a CMM, machine tool, semiconductor-related equipment and form measuring machine. Made from Alumina-ceramic 5mm/2 pitch gradation scales Precision-lapped measuring surface Double-faced type is lapping the double face, which can be used for straightness in horizontal and vertical as a reference square. Lightweight Supplied with fitted wooden case. Metric Nominal length Order No.* 4mm 3-32-33 7mm 3-35-33 mm 3-37-33 3mm 3-3-33 Inch High-accuracy model Nominal length Order No.* Straightness Size (L x H x W) Mass 6 3-322-33.3µm 44 x 35 x 5mm.8kg 28 3-325-33.5µm 74 x 35 x 5mm 3kg 4 3-327-33.µm 4 x 45 x 8mm 8kg 52 3-32-33.5µm 34 x 45 x 8mm kg Technical Data Provided with inspection certificate. Metric Nominal length Order No.* 4mm 3-332-33 7mm 3-335-33 mm 3-337-33 3mm 3-33-33 Inch Ultra-high accuracy model Nominal length Order No.* Straightness Size (L x H x W) Mass 6 3-342-33.2µm 44 x 35 x 5mm.8kg 28 3-345-33.4µm 74 x 35 x 5mm 3kg 4 3-347-33.5µm 4 x 45 x 8mm 8kg 52 3-34-33.7µm 34 x 45 x 8mm kg Cross section Lapped surface H W Double-faced type Double-faced type 22.5 Lapped surface 22.5 Metric Nominal length Order No.* 4mm 3-352-33 7mm 3-355-33 mm 3-357-33 3mm 3-35-33 Inch Double-faced model Nominal length Order No.* Straightness Size (L x H x W) Mass 6 3-362-33.3µm 44 x 45 x 8mm 3.2kg 28 3-365-33.5µm 74 x 45 x 8mm 5.5kg 4 3-367-33.µm 4 x 45 x 8mm 8kg 52 3-36-33.5µm 34 x 45 x 8mm kg H W Graduation E-3
Technical Data Squareness: Refer to the list of specifications Straightness: Refer to the list of specifications Dial test indicator provided Range:.2mm Graduation:.2mm Accuracy: 3µm Square Master SERIES 3 Squareness / Straightness Measuring Instrument Squareness (perpendicularity) and straightness measurements can be performed accurately and efficiently by moving a lever. With a dial test indicator for reading displacements. Its own squareness is adjustable for highaccuracy measurement. Optional Accessory : Riser blocks (see page E-27.)* 57: Adjustable holder 55: Extension holder 565: Feeler** *Not available for 45mm model. **Adapter (283) is required for metric model. Adjustable holder No.57 ø6 65 7.5 Extension holder No.55 Unit: mm 22 5 Unit: mm 3-25 3-225 3-245 Metric Vertical travel Order No. Squareness Straightness Mass (kg) 5mm 3-25 3µm 2µm 3.7 25mm 3-225 6µm 2.5µm 6.2 45mm 3-245 µm 3.5µm 24 ø6 2 Indicator holder Feeler No.565 25 Connector pin 88 Unit: mm 83 67 6 Test indicator Feeler 72 54 54 2 25 Connector pin Indicator holder E-3
Standard Scales SERIES 82 Made of Low-Expansion Glass High-precision glass scales manufactured under Mitutoyo s leading-edge Linear Scale production technology. High accuracy is guaranteed to be used as a standard for calibrating graduated scales. 82-52-5 82-5-5 Technical Data Accuracy (at 2 C): (.5+L/)µm, L = Measured length (mm) Glass material: Low expansion glass Thermal expansion coefficient: 8x -8 /K Graduation: mm Graduation thickness: 4µm Mass:.75kg (25mm),.8kg (5mm) DIMENSIONS W L Range Graduation Working Standard Scales SERIES 82 T 4 2 5 Unit: mm Graduation thickness: 4µm Alignment mark thickness: 2µm Metric Range Order No. L W T 25mm 82-5-5 28mm 2mm mm 25mm 82-5-6* 28mm 2mm mm 5mm 82-52-5 53mm 3mm 2mm 5mm 82-52-6* 53mm 3mm 2mm *with English JCSS certificate. High-precision glass scales manufactured under Mitutoyo s leading-edge linear scale production technology. Ideal for checking magnification accuracy of profile projectors and microscopes, and the table feeding accuracy of measuring equipment. 82-525- 82-523- 82-522- 82-53- Technical Data Accuracy (at 2 C): (.5+2L/)µm, L = Measured length (mm) Glass material: Sodium glass Thermal expansion coefficient: 8.5x -6 /K Graduation:.mm (thickness: 2µm).5mm (thickness: 5µm) mm (thickness: µm) DIMENSIONS.mm graduation 22.5mm graduation 36 mm graduation 36 L Renge L Renge L Renge Graduation 2.7 Graduation 4.7 Graduation 4.7. graduation.5 2.5 3.5 2.5 3.5 3.5 2 2 5.7.5 5 2 2 5 Unit: mm Metric Range Order No. Graduation L Mass 5mm 82-5-.mm 75mm.23kg mm 82-52-.mm 25mm.24kg 5mm 82-53-.mm 75mm.35kg 2mm 82-54-.mm 225mm.36kg mm 82-52-.5mm 3mm.27kg 2mm 82-522-.5mm 23mm.32kg 3mm 82-523-.5mm 33mm.57kg 4mm 82-524-.5mm 43mm.7kg 5mm 82-525-.5mm 53mm.86kg 25mm 82-53- mm 28mm.55kg 5mm 82-532- mm 53mm.86kg 75mm 82-533- mm 78mm.22kg mm 82-534- mm 3mm.54kg E-32
High-Precision Square SERIES 3 The High-Precision Square gage is used for inspecting the travel straightness and axial perpendicularity of moving elements on equipment, such as machine tools, CMMs, form measuring machines and semiconductorrelated equipment. Four precision-lapped reference surfaces. Better than μm/3mm straightness and perpendicularity. 3-3-2 3-3 Metric Order No. Dimension (W x L x T) Mass 3- x x 25mm.5kg 3-2 6 x 2 x 25mm 5.kg 3-3 26 x 3 x 3mm 4.kg * 3-3 is supplied with a removable handle. Spring Dividers and Calipers SERIES 5 Spring Divider Fully hardened and tempered joints, spring, washers and divider points. Outside Spring Caliper Contact ends fully rounded to give accurate dimensions. Inside Spring Caliper Ends fully rounded to give accurate contact with a workpiece. Spring divider Outside spring calipers Inside spring calipers Range Order No. Spring divider Outside spring calipers 6" (5mm) 5-22 5-222 5-232 8" (2mm) 5-23 5-223 5-233 Inside spring calipers E-33
Combination Square Set SERIES 8 Measuring heads are attached to the graduated steel rule (blade), allowing versatile measurements on various types of workpieces. The measuring heads come hardened or cast iron-not hardened. Economy sets without a protractor head are available. 3 part set Technical Data Square head: Used to set the rule at degrees or 45 degrees to an edge of a workpiece. Center head: Used to locate centers of round workpieces. Protractor head: Used to set the rule at a desired angle to an edge of a workpiece. Also used for measuring angles. Head Only Hardened Order No. Description 8-2B Square Head for 2"/3mm to 24"/6mm 8-22B Center Head for 2"/3mm to 24"/6mm Head Only Cast iron-not hardened Order No. Description 8-2B Square Head for 2"/3mm to 24"/6mm 8-22B Center Head for 2"/3mm to 24"/6mm 8-3B Protractor Head for 2"/3mm to 24"/6mm Inch/Metric Hardened Combination Square Sets Set No. Blade Square Head Center Head Protractor Size Type Head 8-3B 2" 4R 8-5B 8-2B 8-22B - 8-5B 2" 4R 8-5B 8-2B 8-22B 8-3B* 8-6B 2" 6R 8-52B 8-2B 8-22B 8-3B* 8-7B 2"/3mm E/M 8-53B 8-2B 8-22B 8-3B* 8-B 3mm Metric 8-55B 8-2B 8-22B 8-3B* *Cast iron-not hardened Inch/Metric Cast iron-not hardened Combination Square Sets Set No. Blade Square Head Center Head Protractor Size Type Head 8-83B 2" 4R 8-5B 8-2B 8-22B - 8-85B 2" 4R 8-5B 8-2B 8-22B 8-3B Inch / Metric Blades only Order No. Length Graduations Accuracy (length) 8-5B 2 8, 6, 32, 64ths (4R) 8-52B 2 32, 64, 5, ths (6R) +.5 / -.35 (+.3mm / -.mm) 8-53B 2 x 3mm 32, 64ths,,.5mm 8-55B 3mm,.5,,.5mm 8-7B 8 8, 6, 32, 64ths (4R) +.6 / -.35 (+.5mm / -.mm) 8-73B 8 x 45mm 32, 64ths,,.5mm 8-6B 24 8, 6, 32, 64ths (4R) +.7 / -.35 8-63B 24 x 6mm 32, 64ths,,.5mm (+.8mm / -.mm) E-34
Steel Rules SERIES 82 Clear graduations on satin-chrome finish. Stainless tempered. 82-25 Wide Rigid Rules (thickness 3/64") Order No. Size Graduations Width Accuracy (Length) 82-6 (4R) /8 /6 /32 /64th 3/4 82-2 6 (6R) /32 /64 /5 /th 3/4 82-3 6 (5R) /32 /64 / /th 3/4 82-4 6 (3R) /32 /64 / /5th 3/4 +.4 /.35 82-5 6 x 5mm /32 /64 mm.5mm 3/4 (+.mm /.mm) 82-6 6 x 5mm /5 / mm.5mm 3/4 82-7 6 x 5mm / / mm.5mm 3/4 82-8 6 x 5mm / /5 mm.5mm 3/4 82-5mm mm.5mm mm.5mm mm 82-2 2 (4R) /8 /6 /32 /64th 82-22 2 (6R) /32 /64 /5 /th 82-23 2 (5R) /32 /64 / /th +.5 /.35 82-24 2 (3R) /32 /64 / /5th (+.3mm /.mm) 82-25 2 x 3mm /32 /64 mm.5mm 82-26 2 x 3mm /5 / mm.5mm 82-3 3mm mm.5mm mm.5mm 25mm 82-24 8 (4R) /8 /6 /32 /64 3/6 82-42 8 (6R) /32 /64 /5 /th 3/6 82-43 8 (5R) /32 /64 / /th 3/6 82-45 8 x 45mm /32 /64 mm.5mm 3/6 82-5 45mm mm.5mm mm.5mm 3mm 82-6 24 (4R) /8 /6 /32 /64 3/6 82-62 24 (6R) /32 /64 /5 /th 3/6 82-63 24 (5R) /32 /64 / /th 3/6 82-65 24 x 6mm /32 /64 mm.5mm 3/6 82-7 6mm mm.5mm mm.5mm 3mm +.6" / -.35" (+.5mm / -.mm) +.7 /.35 (+.8mm /.mm) E-35
Steel Rules SERIES 82 Clear graduations on satin-chrome finish. Stainless tempered. 82-265 Full-Flexible Rules (thickness /64") Order No. Size Graduations Width Accuracy (Length) 82-2 6 (4R) /8 /6 /32 /64th /2 82-22 6 (6R) /32 /64 /5 /th /2 82-23 6 (5R) /32 /64 / /th /2 82-24 6 (3R) /32 /64 / /5th /2 +.4 /.35 82-25 6 x 5mm /32 /64 mm.5mm /2 (+.mm /.mm) 82-26 6 x 5mm /5 / mm.5mm /2 82-27 6 x 5mm / / mm.5mm /2 82-28 6 x 5mm / /5 mm.5mm /2 82-2 5mm mm.5mm mm.5mm 2mm 82-22 2 (4R) /8 /6 /32 /64th /2 82-222 2 (6R) /32 /64 /5 /th /2 82-223 2 (5R) /32 /64 / /th /2 +.5 /.35 82-224 2 (3R) /32 /64 / /5th /2 (+.3mm /.mm) 82-225 2 x 3mm /32 /64 mm.5mm /2 82-226 2 x 3mm /5 / mm.5mm /2 82-23 3mm mm.5mm mm.5mm 2mm 82-4 8 (4R) /8 /6 /32 /64 3/4 82-242 8 (6R) /32 /64 /5 /th 3/4 82-243 8 (5R) /32 /64 / /th 3/4 82-245 8 x 45mm /32 /64 mm.5mm 3/4 82-25 45mm mm.5mm mm.5mm 8mm 82-26 24 (4R) /8 /6 /32 /64 3/4 82-262 24 (6R) /32 /64 /5 /th 3/4 +.6 / -.35 (+.5mm / -.mm) 82-263 24 (5R) /32 /64 / /th 3/4 +.7 /.35 82-264 24 (3R) /32 /64 / /5th 3/4 (+.8mm /.mm) 82-265 24 x 6mm /32 /64 mm.5mm 3/4 82-27 6mm mm.5mm mm.5mm 8mm 82-223 Semi-Flexible Rules SERIES 82 Engraved on frontside only Inch/Metric Order No. Size Graduations Width Accuracy (Length) 82-3 4 x mm /2mm mm /32 /64 /6th 5/8 +.4 /.35 82-32 6 x 5mm /2mm mm /32 /64 /6th 5/8 (+.mm /.mm) 82-33 8 x 2mm /2mm mm /32 /64 /6th 5/8 +.5 /.35 82-35 2 x 3mm /2mm mm /32 /64 /6th 5/8 +.3mm /.mm) 82-37 2 x 5mm /2mm mm /32 /64 /6th 5/8 +.7 /.35 (+.8mm /.mm) 82-3 4 x mm /2mm mm /32 /64 /6th 5/8 +.8 /.4 (+.2mm /.mm) E-36
Thickness Gages SERIES 5, 84 Technical Data Accuracy of Leaves Thickness Nominal Thickness Tolerance Metric.mm to less than.6mm: ±.3mm.6mm to less than.mm: ±.4mm.mm to less than.35mm: ±.5mm.35mm to less than.65mm: ±.8mm.65mm to less than 3.mm: ±.mm Inch.5 to less than.7": ±.2".7 to less than.5": ±.3".5 to less than.25": ±.4".26 to less than.3": ±.45".3 to less than.4": ±.5".4 to less than.75": ±.55".76 to less than.": ±.6". to less than.2": ±.65".2" and over : ±.75" Each leaf is marked with its thickness. Each leaf is detachable. Inch 84-33S Range Order No. Type of Blade Blade Length Composition of leaves.2 -.35 (26 leaves) 5-25 Straight /2 width 3.2 thru.8 by. step plus.22,.24,.25,.28,.3,.32,.35.5 -.25 5-252 Tapered 3.2 thru.25 by. step plus.5,.25 (26 leaves) /4 width at tip.5 -.2 5-254 Straight 3.5,.2,.3,.4,.6,.8,.,.2, (5 leaves) /2 width.5,.2,.3,.4,.75,.,.2.5 -.2 5-255 Straight 4.5.5,.2,.3,.4,.6,.8,., (3 leaves) /2 width.2,.3,.4,.75,.,.2.5 -.5 5-256 Straight 6.5,.2,.3,.4,.8,.,.2,.5 (8 leaves) /2 width Metric Range Order No. Type of Blade Blade Length Composition of leaves.5 - mm 84-33S Straight mm 28 leaves:.5 -.5mm by.mm,.2 - mm by.5mm 84-33S 3mm width 5mm 28 leaves:.5 -.5mm by.mm,.2 - mm by.5mm.5 - mm 84-34S Straight 3mm width 5mm 2 leaves:.5 - mm by.5mm.5 - mm 84-35S Straight mm 3 leaves:.5 -.3mm by.5mm,.4 - mm by.mm 84-3S 3mm width 5mm 3 leaves:.5 -.3mm by.5mm,.4 - mm by.mm.5 -.8mm 84-36S Straight mm leaves:.5 -.2mm by.5mm,.3 -.8mm by.mm 84-38S 3mm width 5mm leaves:.5 -.2mm by.5mm,.3 -.8mm by.mm.3 -.5mm 84-37S Straight 3mm width mm 3 leaves:.3 -.mm by.mm,.2 -.5mm by.mm,.5mm 84-32S 5mm 3 leaves:.3 -.mm by.mm,.2 -.5mm by.mm,.5mm Wooden Box Part No. Part No. Spare 732 6-73 6-6 6343 6-6 6-63 Precision Levels SERIES 6 High-precision longitudinal and transverse vials make it possible to check or level surfaces. Supplied in wooden box. Metric Order No. Sensitivity Accuracy Dimensions (W x D x H) 6-73.2mm/m ±.6mm 2 x 44 x 2mm Inch Order No. Sensitivity Accuracy Dimensions W D H 6-6.2 /2 ±.6 7.87.73.5 6-62.6 /2 ±.3 7.87.73.5 6-63.24 /2 ±.7 7.87.73.5 6-73 6-6 E-37
Digital Universal Protractor SERIES 87 Data output function make it easy to see the statistical data. Can be attached to height gages. gage holder (575, metric) Setting preset value. Removable blade. Technical Data Range: -36 to +36 Tolerance: ±2 (±.3 ) Repeatability: Resolution: (. ) Battery: Lithium Battery Battery life: 2, hours Function Presetting 87-552 Standard Accessories 2" Blade (Code No. 87-3) Battery (CR232) (Part No. 5SAA27) Clamp box for Inch Height Gage (Part No. 574) Plastic Case Code No. 87-552 Model BP-D3E Blade 2 (87-3) Display LCD - 5 digit, (-) sign, character height 6.5mm Measuring range -36 ~ +36 Resolution (. ) Accuracy ± 2 (±.3 ) Repeatability (. ) Mass.45 lbs (65g) Dust / Water protection level IP4 Function Zero, Direction select, Data output / Data hold, Preset, Switchable Seagesimal or Decimal Natation Max. response speed 3 rps Battery Lithium battery (CR232) pc. (Part No. 5SAA27) Battery life 2, hours Alarm Battery voltage low, Over speed error (Err) Temperature Operation temperature: to 4 C Storage temperature: - to 6 C Optional Accessories 87-4 6" blade 87-5 Acute angle attachment 575 Clamp box for Metric Height Gage 5338 Connecting cable (4" / m) 54 Connecting cable (8" / 2m) DIMENSIONS 87-552 Attached to height gage E-38
Technical Data Graduation: 5min. ( - - ) Accuracy Vernier ±5 Straightness [.6"+(.5xL/2)]" Parallelism [.6"+(.5xL/2)]" L = Length in inch Diameter: 2.56" / 7mm Universal Bevel Protractor SERIES 87 High-precision angle gage for accurate angle measurement of machines, molds, and jigs. Can be attached to height gages. 87-4 Universal Bevel Protractors Graduation Order No. Dial Vernier Remarks 87-4 5 min with 6 blade (87-4) and Clamp box for Inch Height Gages (574) 87-6 5min with 2 blade (87-3) and Clamp box for Inch Height Gages (574) Universal Bevel Protractor Accessories and Parts Order No. Remarks 87-3 2 Blade 87-4 6 Blade 87-5 Acute angle attachment 574 Clamp box for Inch Height Gages 575 Clamp box for Metric Height Gages DIMENSIONS Technical Data Graduation: 5 min. ( - - ) Blade edge angle: 3 and 6 Diameter: 2.56 / 7mm Bevel Protractor SERIES 87 Consists of three sheets of stainless steel, the middle one of which is made for angle measurements. Order No. Graduation Remarks 87-2 / 5 min Center black knob locks the blade position Protractor Graduation:, 87-2 E-3
Radius Gages SERIES 86 Radius size is stamped on each gage. Both concave and convex radius gages become a pair. With a locking clamp. 86-5 Technical Data Accuracy: ±.2 Metric Range Order No. Composition of leaves Remarks.4-6mm 86-8 leaves:.4,.8,,.2,.5,.6mm,.75-3mm by.25mm, 3.5-6mm by.5mm arc - 7mm 86-5 34 pairs: - 3mm by.25mm 3.5-7mm by.5mm 8 arc 7.5-5mm 86-6 32 pairs: 7.5-5mm by.5mm 8 arc 5.5-25mm 86-7 5 pairs: 5.5-2mm by.5mm, 2-25mm by mm 8 arc Inch Range Order No. Composition of leaves Remarks /32" - 7/64" 86-3 6 leaves: /32" - 7/64" by 64ths arc /32" - /4" 86-5 pairs: /32" - /4" by 64ths 8 arc 7/64" - /2" 86-2 6 pairs: 7/64" - /2" by 64ths 8 arc /32" - 33/64" 86-4 6 leaves: /32" - 33/64" by 64ths arc 86- Pitch Gages SERIES 88, 5 Thread pitch size is stamped on each gage. Metric, Unified, and Whitworth screw pitch gages. 88- Metric Screw Pitch Gages (6 ) Range Order No. Composition of leaves.25-2.5mm 88-53 28 leaves:.25,.3..35,.4,.45,.5,.55,.6,.65,.7,.75,.8,.85,.,.,.,.2,.25,.3,.4,.5,.6,.7,.75,.8,., 2.. 2.5 mm.35-6mm 88-3 22 leaves:.35,.4,.45,.5,.6,.7,.75,.8,,.25,.5,.75, 2, 2.5, 3, 3.5, 4, 4.5, 5, 5.5, 6mm and 6 angle gage.4-7mm 88-22 2 leaves:.4,.5,.7,.75,.8,.,,.25,.5,.75, 2, 2.5, 3, 3.5, 4, 4.5, 5, 5.5, 6, 6.5, 7mm.4-7mm 88-2 8 leaves:.4,.5,.75,,.25,.5,.75, 2, 2.5, 3, 3.5, 4, 4.5, 5, 5.5, 6, 6.5, 7mm Unified Screw Pitch Gages (6 ) Range Order No. Composition of leaves 4-42 TPI 88-3 leaves: 4, 4 /2, 5, 5 /2, 6, 7, 8,,,, /2, 2, 3, 4, 5, 6, 8, 2, 22, 24, 26, 27, 28, 3, 32, 34, 36, 38, 4, 42 TPI 4-84 TPI 5-253 5 leaves: 4, 4/2, 5, 5/2, 6, 7, 8,,,, /2, 2, 3, 4, 5, 6, 8, 2, 22, 24, 26, 27, 28, 3, 32, 34, 36, 38, 4, 42, 44, 46, 48, 5, 52, 54, 56, 58, 6, 62, 64, 66, 68, 7, 72, 74, 76, 78, 8, 82, 84 TPI Note: Metric and Unified Pitch Gage Set (88-5) is available. It consists of 88-22 (Metric) and 88- (Unified). Metric and Unified Screw Pitch Gage Set (6 ) Range Order No. Composition of leaves.4-7mm / 4-42 TPI 88-5 5 leaves: Set of 88-22 and 88-.5-6mm / 4-56 TPI 88-52 28 leaves: 4, 6, 8,,, -/2, 2, 3, 6, 2, 28, 32, 4, 56 TPI.5,.75,.,.25,.5,.75, 2., 2.5, 3., 3.5, 4., 4.5, 5.. 6. mm Whitworth Screw Pitch Gages (55 ) Range Order No. Composition of leaves 4-42 TPI 88-3 leaves: 4, 4 /2, 5, 5 /2, 6, 7, 8,,,, /2, 2, 3, 4, 5, 6, 8, 2, 22, 24, 26, 27, 28, 3, 32, 34, 36, 38, 4, 42 TPI 4-6 TPI 88-2 28 leaves: 4, 4 /2, 5, 6, 7, 8,,,, 2, 3, 4, 6, 8,, 2, 22, 24, 25, 26, 28, 3, 32, 34, 36, 4, 48, 6 TPI Technical Data Accuracy TPI Metric Pitch (mm) Angular ( minutes) 4-6 6.35-4.23 ±.5 ±35 7-2 3.63-2.2 ±.5 ±4 3-25.5-.2 ±.5 ±45 26-48.8-.53 ±.5 ±5 6.42 ±.5 ±6 E-4
Radius Gages-Sets SERIES 86 Radius Gages are recommended for checking or laying out concave or convex radii. An individual gage for each dimension makes it possible to verify radius or fillet dimensions easier, faster and more accurately in machining, layout, inspection and patternmaking work. The measuring surfaces are precisely finished with smooth, accurate edges. Radius gages are available separately or in six sets. Each radius gage has five measuring locations, and it is identified with its particular radius dimensions. The gages have a satin or dull-chrome finish. The holding cases, provided to protect the sets of radius gages, have indexed pockets to facilitate the selection of the proper size gage. A 4 long holder is furnished with Set No. 86- to make it possible to check radii in confined or hard-to-reach locations. Accuracy: ±.6" /.4mm 5 2 3 4 5 concave and convex radii per leaf. Metric Order No. No. of Leaves Sizes Remarks 86-2 26.5-3mm by.5mm arc Inch Order No. No. of Leaves Sizes Remarks 86-25 /64 7/64 by 64ths Holder and /32 /2 by 32nds 86-3 7 /64 7/64 by 64ths 86-4 8 /32 /2 by 32nds 86-5 8 /6 by 6ths Holder 86-6 26..3 by.5 Holder.4. by..2.3 by.2.35.5 by.5 86-7.55 by.5 86- Decimal Radius Part No. Radius Part No.. 278.24 286.5 27.26 287.2 28.28 288.25 28.3 28.3 282.35 282.4 283.4 282.5 284.45 2822.6 285.5 2823.7 286.55 2824.8 287.6 2825. 288.65 2826. 28.7 2827.2 28.75 2828.4 28.8 282.6 282.85 283.8 283. 283.2 284.5 2832.22 285. 2833 Fraction Radius Part No. Radius Part No. /64 244 5/6 245 /32 2442 /32 246 3/64 2443 3/8 246 /6 2444 3/32 2462 5/64 2445 7/6 2463 3/32 2446 5/32 2464 7/64 2447 /2 2465 /8 2448 /6 27 /64 244 5/8 27 5/32 245 /6 272 /64 245 3/4 273 3/6 2452 3/6 274 3/64 2453 7/8 275 7/32 2454 5/6 276 5/64 2455 277 /4 2456 7/64 2457 /32 2458 E-4
Digital Protractor SERIES 5 These digital protractors present inclination values on an easy-to-read LCD. The measurements are generated by an electronic gravity sensor and processed by the latest low-power electronic circuit technology. Full 36 range ( x 4). Machined aluminum frame. Alternate reference (zero). Reading hold. Simple calibration requiring no special fixtures. Display remains upright to view at all angles. (5-37, Pro 36 Model). RS232C output. (5-38 Pro 36 Model). Supplied in fitted carrying case. Front View 5-37 Back View 5-38 Back View Order No. 5-37 5-38 Model Pro 36 Pro 36 Range 36 ( x4) 36 ( x4) Resolution.. ( to. ). ( to ) Accuracy ±. Level ±, Plumb ± ±.2 Maximum error ±.5 ( to ) ±. (8 to ) ±.2 ( to 8 ) Repeatability ±. ±.5 Cross Axis Error Minimal Minimal Battery Life 5 Hrs. Standard -Volt Battery 5 Hrs. Standard -Volt Battery Temperature Operation Storage -5 C to 5 C (23 to 22 F) -2 C to 65 C (-4 F to 4 F) -5 C to 5 C (23 to 22 F) -2 C to 65 C (-4 F to 4 F) Weight 28g (.2oz.) 25g (.4oz.) Output N/A RS-232C Compatible Standard Accessories Plastic Case Plastic Case ±Represents clockwise or counter-clockwise slope. Optional Accessories 5AAA83A RS-232C Output cable w/foot switch FOOT SWITCH 2m TO DIGITAL PROTRACTOR DB, FEMALE TO PC OR INTERFACE UNIT 2m P DIMENSIONS 5AAA83A RS-232C Output cable w/foot switch P-P 53 Unit: mm 3 ON/OFF HOLD. HOLD ALT ZERO ALT ZERO 4 4 5 (Distance between two M3 x.5 tapped holes) E-42
Digital Hand Tachometers SERIES 82 New digital hand tachometers are compact and easy to handle. NIST certification is supplied with each digital hand tachometer. Model PH-2LC (82-552) has laser diode detection and a combination of contact and non-contact measurement. Supplied with plastic carrying case. DIMENSIONS 82-55 82-552 Order No. 82-55 82-552 Model No. PH-A PH-2LC Revolution per minute. 25, rpm Rotation speed Non-contact: 6., rpm; Contact: 6. 25, rpm Measuring accuracy Revolution Surface, Speed, Length 82-55 82-552. 5.rpm: ±rpm, 6. 25, rpm: ±.6% and ±.5 digit ±.4% and digit 6. 5. rpm: ±rpm, 6., rpm ±.6% and ±.5 digit ±.4% and ± digit Detection Optical coupler, 2 pulses per revolution Laser diode Outside dimensions 4.83 L x 2.52 W x.24 H (22.5mm x 64mm x 3.5mm) 4.55 L x 2.52 W x.24 H Overall length with contact adapter: 4mm Mass 7 g 6 g Power Battery: AA 3 pcs. Battery: AA 3 pcs. Optional Accessories for Digital Hand Tachometers Order No. Description Dimension Drawing 4 Cone Adapter, Standard D = /2 5 Cone Adapter, 3/4 D = 3/4 52 Cone Adapter, -/4 D = -/4 d = /2 53 Funnel Adapter, Standard D = /2 54 Funnel Adapter, 3/4 D = 3/4 55 Measuring Wheel FPM (6 cir), Standard D =. 56 Measuring Wheel FPM (2 cir) D = 3.82 57 Measuring Wheel YPM (. yard cir) D =.5 58 Measuring Wheel MPM (. meter cir) D =.25 5 Reflective Tabs /2 square (35 pcs) 6 Extension Shaft (3 length) E-43
Bench Center SERIES 67 Used with a dial test indicator (optional), the bench center provides precision measurement of concentricity verification on cylindrical workpieces. With an indicator clamp. (Holding stem diameter:.53mm /.375 ) DIMENSIONS 44 5 4 3 Unit: mm Technical Data Maximum workpiece dia.: 3mm Maximum workpiece height: 5mm Mass: 3kg Spindle Tip Material: Hardened Steel 75 67-2- 55 67-2- Order No. A B C D E F G H 67-23- 3 4 5 7 78 4 6 34.5 67-2- 5 45 75 8 37 36 6 4.5 67-24- 7 8 4 5 65 4.5 67-22- 25 6 6 5 4 23 Order No. Center-to-Center Workpiece Capacity Max. Parallelism Flatness Attachment Mass (kg) Diameter Weight Hold of Centers of Surface Diameter 67-23- 5. / 5mm 3.8 7.5 lbs. (8kg).2.4 Ø3/8 7 67-2-.8 / 3mm 5.8 35 lbs. (6kg).2.6 Ø3/8 3 67-24- 7.7 / 45mm 7.8 44 lbs. (2kg).2.7 Ø3/8 6 67-22- 23.6 / 6mm.8 66 lbs. (3kg).24.8 Ø3/8 7 Granite Surface Plate Accessories SERIES 57 These accessories are made from the same high-quality black granite as Mitutoyo surface plates, allowing flexibility in work holding and positioning. Standard Accessories: 56AAK66 Indicator rod assembly 67-2- 67-23- 56AAK6R Indicator rod assembly 67-22- 67-24- Optional Accessories: 56AAJ88 Special attachment for mounting 67-2- in vertical position. 56AAJ87 Special attachment for mounting 67-23- in vertical position. Angle Blocks with or without inserts Grade Laboratory* Master** 4 Face 4 Face Size 2 Face no inserts w/ inserts 2 Face no inserts w/ inserts 4 x 4 x 4" 57-767 57-76 57-773 57-867 57-86 57-873 6 x 6 x 6" 57-768 57-762 57-774 57-868 57862 57-874 *Laboratory overall accuracy:.25 per 6. **Master overall accuracy:.5 per 6. Parallels Grade Laboratory Master Pair Size Accuracy 2 Face 4 Face Accuracy 2 Face 4 Face.75 x x 6".3" 57-755 57-75.6" 57-855 57-85.75 x.5 x ".4" 57-756 57-75.8" 57-856 57-85 x 2 x 2".6" 57-757 57-752." 57-857 57-852 V-Blocks Matching Pair V- type have matching accuracy on V from the bottom face only. V-5 type have four face matching accuracy plus V. Grade Laboratory* Master** Size V- V-5 V- V-5 2 x 2 x 2.5" 57-787 57-783 57-887 57-883 3 x 3 x 3" 57-788 57-784 57-888 57-884 6 x 6 x 6" 57-78 57-785 57-88 57-885 *Laboratory overall accuracy:.5 per 6. **Master overall accuracy:. per 6 Angle Blocks 57-862 (without inserts) 57-884 V-Blocks (matching pair) 57-852 Parallels (in pairs) E-44
Black Granite Surface Plate SERIES 57 Cast iron surface plate Granite surface plate Natural granite seasoned for thousands of years is free from deterioration or dimensional change over time. Granite surface plate has many advantages over cast iron surface plates: Twice as hard as cast iron. Minimal changes in dimension due to temperature changes. Free from wringing, so there is no interruption of work. Free from burrs or protrusions because of the fine grain structure and insignificant stickiness; this ensures a high degree of flatness over a long service life and causes no damage to other parts or instruments. Trouble-free operation for use with magnetic materials. Long life and rust-free, resulting in low maintenance costs. Mitutoyo granite surface plates meet or exceed federal specification GGG-P- 463c. Each surface plate is shipped with a Certificate of Accuracy which guarantees its accuracy and verifies its traceability to NIST. All plates from 48 x8 and larger are machine base gray granite. Smaller plates are black granite. Surface plates, to size of specifications other than standard, available by special order. Surface plates, with the bolt screws, available by special order. All Mitutoyo surface plates shipped F.O.B. Escondido, CA. Inch Size lbs.-load / sq. ft. no ledge AA Laboratory Grade A Inspection Grade B Shop Grade H Acc.* Order No. Wt. (lbs) H Acc.* Order No. Wt. (lbs) H Acc.* Order No. Wt. (lbs) 8 x 2 3 5 57-7 3 2 57-8 25 2 2 57-25 x 2 3 5 57-7 4 3 57-8 4 2 2 57-3 2 x 2 3 5 57-72 5 3 57-82 5 3 2 57-2 5 2 x 8 4 5 57-73 4 57-83 4 2 57-3 8 x 8 4 5 57-74 5 4 57-84 5 3 2 57-4 8 x 24 4 65 5 7-75 2 4 3 57-85 2 4 26 57-5 2 24 x 24 5 7 57-76 3 4 4 57-86 25 3 28 57-6 2 24 x 3 5 75 57-77 4 5 5 57-87 4 4 3 57-7 3 24 x 36 6 85 57-78 6 5 7 57-88 5 4 34 57-8 4 24 x 48 8 5 57-7 6 3 57-8 8 5 6 57-65 3 x 36 6 57-7 8 5 2 57-8 6 5 4 57-6 3 x 48 8 5 57-7 3 6 3 57-8 6 6 57-3 x 6 2 2 57-72 5 57-82 535 8 57-2 5 36 x 36 6 57-73 5 2 57-83 78 5 4 57-3 7 36 x 48 8 5 57-74 5 6 3 57-84 2 6 6 57-4 2 36 x 6 2 2 57-75 285 4 57-85 235 8 8 57-5 36 x 72 2 25 57-76 34 5 57-86 285 8 57-6 23 48 x 48 8 2 57-77 225 6 4 57-87 525 6 8 57-7 5 48 x 6 2 25 57-78 38 5 57-88 35 8 57-8 2525 48 x 72 2 3 57-7 45 6 57-8 38 8 2 57-35 48 x 84 4 35 57-72 65 2 7 57-82 5325 4 57-2 445 48 x 6 4 4 57-72 7 2 8 57-82 65 6 57-2 55 48 x 8 4 5 57-722 7 2 57-822 683 2 57-22 57 48 x 2 8 7 57-723 3 6 4 57-823 6 4 28 57-23 88 48 x 44 8 8 57-724 35 6 6 57-824 22 4 32 57-24 5 6 x 6 4 25 57-725 55 2 5 57-825 48 57-25 4 6 x 72 4 35 57-726 66 2 7 57-826 575 4 57-26 4 6 x 6 4 5 57-727 88 2 57-827 76 2 57-27 65 6 x 2 6 7 57-728 5 4 4 57-828 2 28 57-28 8 6 x 44 8 57-72 65 6 8 57-82 5 4 36 57-2 42 72 x 72 4 4 57-73 8 2 8 57-83 7 6 57-3 57 72 x 6 6 5 57-73 225 4 57-83 8 2 2 57-3 2 72 x 2 6 7 57-732 57 4 4 57-832 34 2 28 57-32 4 72 x 44 8 57-733 23 6 2 57-833 8 4 4 57-33 5 * Accuracies shown in microinches (µin) E-45
Inch Size 5 lbs.-load / sq. ft. no ledge AA Laboratory Grade A Inspection Grade B Shop Grade H Acc. Order No. Wt. H Acc. Order No. Wt. H Acc. Order No. Wt. 8 x 2 2 5 57-74 25 2 57-84 25 2 2 57-4 25 2 x 8 3 5 57-74 8 3 57-84 8 2 2 57-4 6 8 x 24 4 65 57-742 2 3 3 57-842 65 2 26 57-42 24 x 36 5 85 57-743 5 4 7 57-843 4 3 34 57-43 3 36 x 48 6 5 57-746 2 5 3 57-846 4 6 57-46 8 SIZE H SIZE Steel Stands Steel stands for supporting black granite surface plates, at working levels, are available either stationary or with casters. Sizes and weights are given below. Size Stationary With Casters Order No. Wt. Order No. Wt. 2 x 8 57-5 42lbs 57-5- 46lbs 8 x 8 57-5 46lbs 57-5- 5lbs 8 x 24 57-52 5lbs 57-52- 56lbs 24 x 24 57-54 65lbs 57-54- 6lbs 24 x 3 57-55 7lbs 57-55- 74lbs 24 x 36 57-56 73lbs 57-56- 77lbs 24 x 48 57-57 lbs 57-57- 4lbs 3 x 36 57-6 85lbs 57-6- 8lbs 3 x 48 57-6 5lbs 57-6- lbs 3 x 6 57-62 5lbs 57-62- lbs 36 x 36 57-63 5lbs 57-63- lbs 36 x 48 57-64 5lbs 57-64- lbs 36 x 6 57-65 6lbs 57-65- 64lbs 36 x 72 57-66 8lbs 57-66- 84lbs 48 x 48 57-67 lbs 57-67- 4lbs 48 x 6 57-68 2lbs 57-68- 24lbs 48 x 72 57-6 25lbs 57-6- 2lbs 48 x 84 57-7 32lbs 57-7- 324lbs 48 x 6 57-7 335lbs 57-7- 33lbs 48 x 8 57-72 35lbs 57-72- 354lbs 48 x 2 57-73 365lbs 57-73- 36lbs 48 x 44 57-74 43lbs 57-74- 434lbs 6 x 6 57-75 245lbs 6 x 72 57-76 34lbs 6 x 6 57-77 375lbs 6 x 2 57-78 455lbs 6 x 44 57-7 48lbs 72 x 72 57-8 38lbs 72 x 6 57-8 465lbs 72 x 2 57-82 5lbs 72 x 44 57-83 53lbs 48x72 and smaller include keepers to prevent the surface plate from being pushed off the stand. Note: The total height of stand and granite plate is 36. If ordering only stand, stand height will be made according to a Grade A granite plate thickness. E-46