K11 DOORS K11.13 THREE-POINT LOCKS SERIES 8400 01.04.2017 Waregemstraat 5-9870 Zulte - Belgium - T. +32 9 388 88 81 - F. +32 9 388 88 21 - commercial@sobinco.com - www.sobinco.com
CONTENTS 1. Three-point locks series 8400... K11.13.03 1.1. General K11.13.03 1.2. Turning of the latch bolt and installation of the cylinder K11.13.04 2. Types... K11.13.05 2.1. Three-point lock with latch bolt and dead bolt K11.13.05 2.2. Three-point lock with narrow latch bolt and dead bolt K11.13.06 2.3. Three-point lock with roller and dead bolt K11.13.07 2.4. Three-point lock with dead bolt only K11.13.08 2.5. Three-point lock with short (K) or long (L) faceplate K11.13.09 3. Section preparations for lock...k11.13.10 4. Three-point locks series 8400E...K11.13.11 5. Three-point locks series 9400 with SKG certificate... K11.13.12 6. Keeps... K11.13.15 6.1. General K11.13.15 6.2. Keeps in zinc alloy K11.13.15 6.3. Adjustable keeps in stainless steel K11.13.17 6.4. Keeps in stainless steel K11.13.18 6.5. Keeps in stainless steel with plastic case K11.13.19 7. Section preparations for keeps... K11.13.20 8. Electric strikes... K11.13.21 8.1. General information K11.13.21 8.2. Types and function K11.13.22 8.3. Electric strikes series 8355-.-. K11.13.23 9. Application examples... K11.13.25 K11.13.02
1. Three-point locks series 8400 1.1. General K11.13 The 3 dead bolts are pivoting, rather than sliding. They are therefore longer than conventional bolts, so there is the same proportion of the dead bolt within the lockcase as is engaged into the frame, making it extremely difficult for burglars to force entry. The three-point lock has a special mechanism in the lockcase together with tapered top and bottom dead bolts which pull the vent section against the frame when locking the door, to provide an effective weather seal. Also a slightly deformed door (for example due to extreme weather conditions) can be closed without having to force the key. Faceplate (flat or U-form) in stainless steel. Very narrow lock: lockcase width = 15.5 mm. Locking and unlocking by a single turn of 360 with the cylinder key. The latch bolt can be operated by the door handle as well as by the key. Two holes above and below the handle opening allow the door handles to be screwed to each other through the lock, so there are no screws visible from the outside. In addition to a more pleasing look and increased security a much stronger fastening of the door handles is obtained. The lock can be used left hand and right hand simply by turning the latch bolt. The three-point lock is entirely made of non-corroding materials. Finish: faceplate : stainless steel lockcases : zinc alloy latch bolt : zinc alloy nickel plated dead bolts : zinc alloy nickel plated Vent height: With short lock: 1825-2100 mm With standard lock: 2100-2500 mm With long lock: 2500-2900 mm K11.13.03
The locks are tested in accordance with the European standard EN 12209:2003/AC:2005 and obtained the following classification code: Category of use Durability Door mass Fire resistance Safety Corrosion resistance Security Door application Type of key operation Type of spindle Key identification 3 X 7 0 0 C 2 B A 2 0 1.2. Turning of the latch bolt and installation of the cylinder Note: When a lock is mounted without cylinder, the plastic protection piece and screw should not be removed. Turning of the latch bolt (A): 1. Put the dead bolt (B) in locked position. 2. Pull the latch bolt (A) forwards with a pair of pliers. 3. Turn the latch bolt (A) 180. 4. Move the latch bolt (A) backwards. Installation of the cylinder: Only for locks: n...-..-40 with flat faceplate n...-u..-35 with U-faceplate n...-u24-37 with U-faceplate 1. Install the cylinder. 2. Put the dead bolt (B) in locked position: Case 1: the key can be removed from the cylinder. Case 2: the key can not be removed from the cylinder. * unscrew the hexagon socket screw (1). * turn the key to put the catch (2) in the lower position. * tighten screw (1). K11.13.04
2. Types 2.1. Three-point lock with latch bolt and dead bolt Flat faceplate Order code A B C E 8401-16-30 27 30 16 8405-16-30 13.5 8401-16-35 32 35 16 8405-16-35 13.5 8401-16-40 37 40 16 8405-16-40 13.5 8401-20-30 27 30 20 8405-20-30 13.5 8401-20-35 32 35 20 8405-20-35 13.5 8401-20-40 37 40 20 8405-20-40 13.5 8401-24-30 27 30 24 8405-24-30 13.5 8401-24-35 32 35 24 8405-24-35 13.5 8401-24-40 37 40 24 8405-24-40 13.5 U-faceplate Order code A B C D E 8401-U22-25 22.5 29 22 6.5 8405-U22-25 14.5 8401-U22-30 27.5 34 22 6.5 8405-U22-30 14.5 8401-U22-35 32.5 39 22 6.5 8405-U22-35 14.5 8401-U24-25 22.5 29 24 6.5 8405-U24-25 14.5 8401-U24-27 24 29 24 5 8405-U24-27 14.5 8401-U24-30 27.5 34 24 6.5 8405-U24-30 14.5 8401-U24-32 29 34 24 5 8405-U24-32 14.5 8401-U24-35 32.5 39 24 6.5 8405-U24-35 14.5 8401-U24-37 34 39 24 5 8405-U24-37 14.5 K11.13.05
2.2. Three-point lock with narrow latch bolt and dead bolt Flat faceplate Order code A B C E 8401B-16-30 27 30 16 8405B-16-30 13.5 8401B-16-35 32 35 16 8405B-16-35 13.5 8401B-16-40 37 40 16 8405B-16-40 13.5 8401B-20-30 27 30 20 8405B-20-30 13.5 8401B-20-35 32 35 20 8405B-20-35 13.5 8401B-20-40 37 40 20 8405B-20-40 13.5 8401B-24-30 27 30 24 8405B-24-30 13.5 8401B-24-35 32 35 24 8405B-24-35 13.5 8401B-24-40 37 40 24 8405B-24-40 13.5 U-faceplate Order code A B C D E 8401B-U22-25 22.5 29 22 6.5 8405B-U22-25 14.5 8401B-U22-30 27.5 34 22 6.5 8405B-U22-30 14.5 8401B-U22-35 32.5 39 22 6.5 8405B-U22-35 14.5 8401B-U24-25 22.5 29 24 6.5 8405B-U24-25 14.5 8401B-U24-27 24 29 24 5 8405B-U24-27 14.5 8401B-U24-30 27.5 34 24 6.5 8405B-U24-30 14.5 8401B-U24-32 29 34 24 5 8405B-U24-32 14.5 8401B-U24-35 32.5 39 24 6.5 8405B-U24-35 14.5 8401B-U24-37 34 39 24 5 8405B-U24-37 14.5 K11.13.06
2.3. Three-point lock with roller and dead bolt K11.13 Flat faceplate Order code A B C 8411-16-30 27 30 8411-16-35 32 35 16 8411-16-40 37 40 8411-20-30 27 30 8411-20-35 32 35 20 8411-20-40 37 40 8411-24-30 27 30 8411-24-35 32 35 24 8411-24-40 37 40 U-faceplate Order code A B C D 8411-U22-25 22.5 29 6.5 8411-U22-30 27.5 34 22 6.5 8411-U22-35 32.5 39 6.5 8411-U24-25 22.5 29 6.5 8411-U24-27 24 29 5 8411-U24-30 27.5 34 6.5 24 8411-U24-32 29 34 5 8411-U24-35 32.5 39 6.5 8411-U24-37 34 39 5 Adjustable roller The roller has an adjustment range of 8 mm. Adjust the roller with a hexagonal spanner of 2.5 mm. K11.13.07
2.4. Three-point lock with dead bolt only Flat faceplate Order code A B C 8421-16-30 27 30 8421-16-35 32 35 16 8421-16-40 37 40 8421-20-30 27 30 8421-20-35 32 35 20 8421-20-40 37 40 8421-24-30 27 30 8421-24-35 32 35 24 8421-24-40 37 40 U-faceplate Order code A B C D 8421-U22-25 22.5 29 6.5 8421-U22-30 27.5 34 22 6.5 8421-U22-35 32.5 39 6.5 8421-U24-25 22.5 29 6.5 8421-U24-27 24 29 5 8421-U24-30 27.5 34 6.5 24 8421-U24-32 29 34 5 8421-U24-35 32.5 39 6.5 8421-U24-37 34 39 5 K11.13.08
2.5. Three-point lock with short (K) or long (L) faceplate All locks are also available as shorter or longer version: the distance between main lock and top lock is smaller or bigger as for the standard type. K11.13 Faceplate 6.5 mm Faceplate 5 mm 84..K-..-.. 84..K-U..-.. 84..L-..-.. 84..L-U..-.. K11.13.09
3. Section preparations for lock Flat faceplate U-shaped faceplate U-shaped faceplate Lock A B C D 84..-..-.. 250 250 571 179 84..K-..-.. 225 0 296 179 84..K-U..-.. 225 0 296 179 84..L-..-.. 450 250 771 179 84..L-U..-.. 450 250 771 0 Hole ø14 mm is not required for locks with roller or locks without latch bolt. R = Height reference. K11.13.10
4. Three-point locks series 8400E K11.13 Type E = with deactivating mechanism: All locks with latch bolt series 8400 can be provided with this mechanism to deactivate the latch bolt. The latch bolt is deactivated by pushing it into the lockcase and by turning the small cover. Locks: With flat faceplate Order code A B C E 8401E-20-30 27 30 20 8405E-20-30 13.5 8401E-20-35 32 35 20 8405E-20-35 13.5 8401E-20-40 37 40 20 8405E-20-40 13.5 8401E-24-30 27 30 24 8405E-24-30 13.5 8401E-24-35 32 35 24 8405E-24-35 13.5 8401E-24-40 37 40 24 8405E-24-40 13.5 deactivation latch bolt With U-faceplate Order code A B C D E 8401E-U22-25 22.5 29 22 6.5 8405E-U22-25 14.5 8401E-U22-30 27.5 34 22 6.5 8405E-U22-30 14.5 8401E-U22-35 32.5 39 22 6.5 8405E-U22-35 14.5 8401E-U24-25 22.5 29 24 6.5 8405E-U24-25 14.5 8401E-U24-27 24 29 24 5 8405E-U24-27 14.5 8401E-U24-30 27.5 34 24 6.5 8405E-U24-30 14.5 8401E-U24-32 29 34 24 5 8405E-U24-32 14.5 8401E-U24-35 32.5 39 24 6.5 8405E-U24-35 14.5 8401E-U24-37 34 39 24 5 8405E-U24-37 14.5 K11.13.11
5. Three-point locks series 9400 with SKG certificate General information The Foundation for Quality of window and door systems (SKG) is a recognised and independent test institution. The Foundation tests and awards certificates for windows, doors, facades and fittings. SKG awards stars to specify the quality of high security fittings and complete windows and doors. There are 3 categories to distinguish the different classes of security. Standard: 1 star Heavy: 2 stars Extra heavy: 3 stars The conditions to obtain this product certificate are described in the SKG Regulations. The tests are done in accordance with NEN 5089 Safety against burglary of buildings: high security fittings. The locks have been tested by SKG in the Netherlands. 2 stars are awarded to the locks in accordance with the star rating indicated in the KOMO certificate of SKG. Three-point locks series 9400 look the same and are mounted in the same way as three-point locks series 8400, but offer a higher security against forced entry. The dead bolt of the main lock is equipped with two invisible cemented carbide rollers and the upper and lower dead bolt are both equipped with two visible bars in hard metal. This makes it impossible to cut the 3 bolts with a hacksaw. Recommended for double action doors and doors without rebate. These high security locks are especially adapted and reinforced to comply with the rigorous SKG standards for security against forced entry. The two fixing holes, above and below the handle follower are suitable for screws M6. All other dimensions of the SKG type are the same as for the standard type. K11.13.12
With flat faceplate SKG-type Standard type Order code Category Certificate number Order code Page 8401P-16-30 - - 8401-16-30 K11.13.05 8405P-16-30 - - 8405-16-30 K11.13.05 8411P-16-30 - - 8411-16-30 K11.13.07 8421P-16-30 - - 8421-16-30 K11.13.08 8401P-16-35 - - 8401-16-35 K11.13.05 8405P-16-35 - - 8405-16-35 K11.13.05 8411P-16-35 - - 8411-16-35 K11.13.07 8421P-16-35 - - 8421-16-35 K11.13.08 8401P-16-40 - - 8401-16-40 K11.13.05 8405P-16-40 - - 8405-16-40 K11.13.05 8411P-16-40 - - 8411-16-40 K11.13.07 8421P-16-40 - - 8421-16-40 K11.13.08 9401-20-30 417.211.01 8401-20-30 K11.13.05 9405-20-30 417.211.01 8405-20-30 K11.13.05 9411-20-30 417.211.01 8411-20-30 K11.13.07 9421-20-30 417.211.01 8421-20-30 K11.13.08 9401-20-35 417.211.01 8401-20-35 K11.13.05 9405-20-35 417.211.01 8405-20-35 K11.13.05 9411-20-35 417.211.01 8411-20-35 K11.13.07 9421-20-35 417.211.01 8421-20-35 K11.13.08 9401-20-40 417.211.01 8401-20-40 K11.13.05 9405-20-40 417.211.01 8405-20-40 K11.13.05 9411-20-40 417.211.01 8411-20-40 K11.13.07 9421-20-40 417.211.01 8421-20-40 K11.13.08 9401-24-30 417.211.01 8401-24-30 K11.13.05 9405-24-30 417.211.01 8405-24-30 K11.13.05 9411-24-30 417.211.01 8411-24-30 K11.13.07 9421-24-30 417.211.01 8421-24-30 K11.13.08 9401-24-35 417.211.01 8401-24-35 K11.13.05 9405-24-35 417.211.01 8405-24-35 K11.13.05 9411-24-35 417.211.01 8411-24-35 K11.13.07 9421-24-35 417.211.01 8421-24-35 K11.13.08 9401-24-40 417.211.01 8401-24-40 K11.13.05 9405-24-40 417.211.01 8405-24-40 K11.13.05 9411-24-40 417.211.01 8411-24-40 K11.13.07 9421-24-40 417.211.01 8421-24-40 K11.13.08 K11.13.13
With U-faceplate SKG-type Standard type Order code Category Certificate number Order code Page 9401-U22-25 417.211.01 8401-U22-25 K11.13.05 9405-U22-25 417.211.01 8405-U22-25 K11.13.05 9411-U22-25 417.211.01 8411-U22-25 K11.13.07 9421-U22-25 417.211.01 8421-U22-25 K11.13.08 9401-U22-30 417.211.01 8401-U22-30 K11.13.05 9405-U22-30 417.211.01 8405-U22-30 K11.13.05 9411-U22-30 417.211.01 8411-U22-30 K11.13.07 9421-U22-30 417.211.01 8421-U22-30 K11.13.08 9401-U22-35 417.211.01 8401-U22-35 K11.13.05 9405-U22-35 417.211.01 8405-U22-35 K11.13.05 9411-U22-35 417.211.01 8411-U22-35 K11.13.07 9421-U22-35 417.211.01 8421-U22-35 K11.13.08 9401-U24-25 417.212.01 8401-U24-25 K11.13.05 9405-U24-25 417.212.01 8405-U24-25 K11.13.05 9411-U24-25 417.212.01 8411-U24-25 K11.13.07 9421-U24-25 417.212.01 8421-U24-25 K11.13.08 9401-U24-30 417.212.01 8401-U24-30 K11.13.05 9405-U24-30 417.212.01 8405-U24-30 K11.13.05 9411-U24-30 417.212.01 8411-U24-30 K11.13.07 9421-U24-30 417.212.01 8421-U24-30 K11.13.08 9401-U24-35 417.212.01 8401-U24-35 K11.13.05 9405-U24-35 417.212.01 8405-U24-35 K11.13.05 9411-U24-35 417.212.01 8411-U24-35 K11.13.07 9421-U24-35 417.212.01 8421-U24-35 K11.13.08 9401-U24-27 417.211.01 8401-U24-27 K11.13.05 9405-U24-27 417.211.01 8405-U24-27 K11.13.05 9411-U24-27 417.211.01 8411-U24-27 K11.13.07 9421-U24-27 417.211.01 8421-U24-27 9401-U24-32 417.211.01 8401-U24-32 K11.13.05 9405-U24-32 417.211.01 8405-U24-32 K11.13.05 9411-U24-32 417.211.01 8411-U24-32 K11.13.07 9421-U24-32 417.211.01 8421-U24-32 K11.13.08 9401-U24-37 417.211.01 8401-U24-37 K11.13.05 9405-U24-37 417.211.01 8405-U24-37 K11.13.05 9411-U24-37 417.211.01 8411-U24-37 K11.13.07 9421-U24-37 417.211.01 8421-U24-37 K11.13.08 K11.13.14
6. Keeps 6.1. General There are 3 types of keeps: keeps in zinc alloy with case for use with dead bolts. keeps in stainless steel without case for use with dead bolts. keeps in stainless steel with plastic case for use with dead bolts. The keeps are suitable for locks with latch bolt and dead bolt, with roller and dead bolt, or with dead bolt only. The locks have been tested by SKG in the Netherlands. 2 stars are awarded to the locks in accordance with the star rating indicated in the KOMO certificate of SKG. 6.2. Keeps in zinc alloy The keeps are horizontally adjustable by means of serrated plates. The adjustment range is 3 mm. The keeps are encased which gives a neat appearance and keeps the frame section free from dirt. Finish: keeps in zinc alloy, coated natural colour. Fixing by means of serrated plates with a horizontal adjustment range of 3 mm. Top and bottom keep Order code G H I 8352-1 5.5 0 18 8352-2 14.5 0 18 8352-3 11 0 18 8352-4 8.5 0 18 8352-5 5.5 5 18 8352-7 5.5 0 23 Order code Middle keep G H I 8351-1 5.5 0 18 8351-2 14.5 0 18 8351-3 11 0 18 8351-4 8.5 0 18 8351-5 5.5 5 18 8351-7 5.5 0 23 K11.13.15
n 8352-10 n 8351-10 K11.13.16
6.3. Adjustable keeps in stainless steel Extra slim keeps for sections with minimal installation depth. The keeps are horizontally adjustable by means of 2 eccentric rollers. The adjustment range is 3 mm. Finish: stainless steel. K11.13 allen key s4 allen key s4 n 8358-2 allen key s4 allen key s4 n 8357-2 K11.13.17
6.4. Keeps in stainless steel Extra slim keeps for sections with minimal installation depth. Finish: keeps in stainless steel. Order code Top and bottom keep G H I J 8354-1 2.5 0 20 10 8354-3 3 0 24 12 8354-5 3 0 20 9 8354-7 3 0 24 9 8354-7B 3 5 24 9 8354-7C 3 5 24 9 Order code Middle keep G H I J 8353-1 2.5 0 20 10 8353-3 3 0 24 12 8353-5 3 0 20 9 8353-7 3 0 24 9 8353-7B 3 5 24 9 8353-7C 3 5 24 9 Fixing holes with a horizontal adjustment range of 3 mm. Keeps n 8353-7C and n 8354-7C are not horizontally adjustable. K11.13.18
6.5. Keeps in stainless steel with plastic case Extra slim keeps for sections with minimal installation depth. Finish: keeps in stainless steel case in black plastic K11.13 Order codes Top and bottom keep G H I J 8354-2 2.5 0 20 10 8354-4 3 0 24 12 8354-6 3 0 20 9 8354-8 3 0 24 9 8354-8B 3 5 24 9 8354-8C 3 5 24 9 Order code Middle keep G H I J 8353-2 2.5 0 20 10 8353-4 3 0 24 12 8353-6 3 0 20 9 8353-8 3 0 24 9 8353-8B 3 5 24 9 8353-8C 3 5 24 9 Fixing holes with a horizontal adjustment range of 3 mm. Keeps n 8353-8C and n 8354-8C are not horizontally adjustable. K11.13.19
7. Section preparations for keeps Profile with frame groove Profile without frame groove Zinc alloy keeps 8351-... and 8352-... (top/bottom) With lock F G 84..-..-.. 637 718 84..K-..-.. 362 443 84..K-U..-.. 362 443 84..L-..-.. 837 918 84..L-U..-.. 837 918 Z 60 Stainless steel keeps 8353-... and 8354-... (top/bottom) With lock F G 84..-..-.. 612 718 84..K-..-.. 337 443 84..K-U..-.. 337 443 84..L-..-.. 812 918 84..L-U..-.. 812 918 Z 85 R = Height reference. KEEP DETAIL adjustable KEEP DETAIL adjustable adjustable adjustable adjustable adjustable K11.13.20
8. Electric strikes 8.1. General information Small electric strike incorporating a spacesaving locking flap, especially developed for installation in aluminium doors. The flap rotates back within the keep when operated. Big advantage: the cut-out is much smaller making the installation aesthetically pleasing. Break-in resistance of strike: 3750 N. Width adjustment of the locking flap: 3 mm. Current consumption: Alternating current (AC): 250 ma at 12V Direct current (DC): 280 ma at 12V The electric strikes are handed. Mechanical Reset button Electrical release connection (version E) Release button Electrical connection Reset button Quick and easy electrical connection. Adjustment range The reset button applies only to type 128 where the strike is held in the release position until the door has been opened. This button resets the electric strike when the door opens. The release button (version E) allows to suspend temporarily the automatic locking upon closing the door. Only available for type 118 and 128. K11.13.21
8.2. Types and function Model 118 The door is only unlocked when you push a button. After releasing the button the door is locked again. This type works on 10-24V AC/DC and may be permanently connected to electrical supply up to 12V. Note: when the door is pushed open by the gaskets, the door can still be open after releasing the button. This can be solved by mounting a door closer on the door. Electric strike Door Operation This type is available with release button (version E). The release button allows to suspend temporarily the automatic locking upon closing the door. Model 128 On releasing the electric strike, for example, from a button on an intercom system, the strike is held in the release position until the door has been opened. The electric strike resets when the door opens. This means there is no need to rush through the door. This type works on 10-24V AC/DC and may be permanently connected to electrical supply up to 12V. This type is available with release button (version E). The release button allows to suspend temporarily the automatic locking upon closing the door. Electric strike Door Operation Model 138 This type works on 12V DC or 24V DC and may be permanently connected to electrical current. The electric strike is mainly used in combination with an emergency or a fire centre. In case of a power failure, the door can be opened. Electric strike Door Operation K11.13.22
8.3. Electric strikes series 8355-.-. Electric strikes with extended faceplate for latch bolt and dead bolt. Finish: keep in aluminium natural anodised. K11.13 left hand = illustrated right hand = opposite view Order code A B C Possibilities 3 mm adjustment 8355-1 5 11.5 6.5 118 10-24V AC/DC 8355-2 8 8 3 8355-3 10 8 3 8355-4 12 8 3 8355-5 8 11.5 6.5 8355-6 15 8 3 118E 10-24V AC/DC 128 10-24V AC/DC 128E 10-24V AC/DC 138-12 12V DC left or right Movement of locking flap 8355-8 10 11.5 6.5 138-24 24V DC Order example: 8355-6-128E left This is an electric strike with release button (E) with faceplate height of 15 mm and an electric strike type 128 (see page K11.13.22) working on 10-24V AC/DC. K11.13.23
3 mm adjustment Order code Possibilities 118 10-24V AC/DC 8355-9 118E 10-24V AC/DC 128 10-24V AC/DC 128E 10-24V AC/DC left or right Movement of locking flap 138-12 12V DC 138-24 24V DC Order example: 8355-9-128E left This is an electric strike with release button (E) and with an electric strike type 128 (see page K11.13.22) working on 10-24V AC/DC. K11.13.24
9. Application examples Bottom lock of three-point lock n 8401-U22-30 + keep n 8352-3 Three-point lock n 8401-20-35 + keep n 8351-5 Three-point lock n 8411-U22-35 Three-point lock n 8401B-20-35 + keep n 8351-5 + electric strike n 8355-1-. right K11.13.25