CD-L, BD01, BD2 Busbar Trunking Systems up to 120 A Catalog LV 70 2009 SIVACON 8PS
Related catalogs Contents Low-Voltage Controls and Distribution SIRIUS SENTRON SIVACON Order No. German/English: Catalog E86060-K1002-A101-A8 E86060-K1002-A101-A7-7600 Incl. PDF CD-ROM Technical Information E86060-T1002-A101-A8 E86060-T1002-A101-A7-7600 LV 1 LV 1 T Systems Controlgear: Contactors and contactor assemblies, solid-state switching devices Protection equipment Motor starters, soft starters and load feeders Monitoring and control devices Detecting devices Commanding and signaling devices Transformers Power supplies Planning and configuration with SIRIUS Power Management System SIVACON Power, distribution boards, busway and cubicle systems SENTRON switching and protection devices for power distribution Air circuit breakers, molded case circuit breakers, switch disconnectors, busbar systems Software for power distribution BETA low-voltage circuit protection Low-Voltage Controls and Distribution Controls and Components for Applications according to UL Order No. German/English: E86060-K1816-A101-A2 E86060-K1816-A101-A1-7600 LV 16 SIRIUS 3RV17 and 3RV18 circuit breakers according to UL 489/ CSA C22.2 No. -02 SIVACON Components for Feeder Circuit SENTRON 3WL air circuit breakers/non-automatic air circuit breakers according to UL 489/IEC 60947-2 SENTRON 3VL Molded Case Circuit Breakers according to UL 489/IEC 60947-2 ALPHA Devices according to UL Standard BETA Devices according to UL standard SIMATIC NET Industrial Communication Order No.: E86060-K6710-A101-B6-7600 IK PI PROFINET/Industrial Ethernet Industrial Wireless Communication PROFIBUS SIMATIC ET 200 distributed I/Os AS-Interface Telecontrol Routers ECOFAST system SIVACON System Cubicles and Cubicle Air-Conditioning Order No.: E86060-K1920-A101-A3-7600 LV 0 System cubicles Cubicle modifications Cubicle expansion components Accessories Special cubicles Cubicle solutions in applications Cubicle air-conditioning Special colors SIDAC Reactors and Filters Order No.: E86060-K2803-A101-A4-7600 SIVACON 8PS CD-L, BD01, BD2 Busbar Trunking Systems up to 120 A Order No.: E86060-K1870-A101-A4-7600 LV 60 LV 70 Commutating reactors for converters Mains reactors for frequency converters Iron-core output reactors Ferrite output reactors Iron-core smoothing reactors Smoothing air-core reactors Filter reactors Application-specific reactors Radio interference suppression filters dv/dt filters Sinewave filters Busbar trunking systems, overview CD-L system (2 A to 40 A) BD01 system (40 A to 160 A) BD2 system (160 A to 120 A) The Offline Mall DVD: E86060-D4001-A10-C7-7600 CA 01 All products of automation, drives and installation technology, including those in the catalogs listed above. The Online Mall Internet: http://www.siemens.com/ automation/mall All products of automation, drives and installation technology, including those in the catalogs listed above. Catalog-PDF Internet: http://www.automation. siemens.com/cd All catalogs for low-voltage controls and distribution can be downloaded as PDF files. Registered trademarks Technical Assistance All product designations may be registered trademarks or product names of Siemens AG or other supplying companies. Third parties using these trademarks or product names for their own purposes may infringe upon the rights of the trademark owners. Further information about low-voltage controls is available on the Internet at: http://www.siemens.com/lowvoltage Expert technical assistance for Low-voltage controls and electrical installation. Tel.: +49 (9 11) 8 9-9 00 Fax: +49 (9 11) 8 9-9 07 E-Mail: technicalassistance@siemens.com
SIVACON 8PS CD-L, BD01, BD2 Busbar Trunking Systems up to 120 A Introduction 1 Catalog LV 70 2009 Busbar Trunking Systems, Overview 2 Replaces: Catalog LV 70 2008 The products in this catalog can also be found in the electronic catalog CA 01. Order No.: E86060-D4001-A10-C7-7600 (DVD) Contact your local Siemens representative The products and systems listed in this catalog are manufactured/sold using a certified quality management system which complies with EN ISO 9001 (Certificate Register No. 121001690 TMS). The certificate is recognized in all IQNet countries. CD-L System 2 A... 40 A 3 BD01 System 40... 160 A 4 BD2 System 160... 120 A Appendix 6
Explanations General data Delivery time class (DT) } Preferred type A 2 working days B 1 week C 3 weeks D 6 weeks X on request Type Order No. Preferred types are available immediately from stock, i.e. are dispatched within 24 hours. Normal quantities of the products are usually delivred within the specified time following receipt of your order at our branch. In exceptional cases, the actual delivery time may differ from that specified. If a type designation contains * characters, it is not complete (e.g. in case of variable lengths) and must be supplemented according to specifications in the table. In this case, the order number is not unique. The delivery times apply up to the ramp at Siemens AG (products ready for dispatch). The transport times depend on the destination and type of shipping. The standard transport time for Germany is 1 day. The delivery times specified here represent the state of 10/2008. They are permanently optimized. Up-to-date information can be found at http://www.siemens.com/automation/mall. When ordering the busbar trunking systems BD01 and BD2, the prefix BVP: must be placed before the article number listed in the catalog, for example: BVP:034262. Packaging sizes (PS) Weight Dimensions The packaging size defines the number, e.g. of units, sets or meters, for outer packaging. Only the quantity defined by the packaging size or a multiple thereof can be ordered! The defined weight in kg refers to the price unit (PU). For the product range covered by LV 70 it is 1. All dimensions in mm. 2 Siemens LV 70 2009
Introduction 1/2 Answers for Industry.1 1/4 Low-Voltage Controls and Distribution. The basis for progressive solutions. 1/6 Busbar trunking systems in action. SIVACON 8PS. 1/8 Made-to-measure, economical solutions. SIVACON 8PS Engineering Tools. Siemens LV 70 2009
1/2 Siemens LV 70 2009
Answers for Industry. Siemens Industry answers the challenges in the manufacturing and the process industry as well as in the building automation business. Our drive and automation solutions based on Totally Integrated Automation (TIA) and Totally Integrated Power (TIP) are employed in all kinds of industry. In the manufacturing and the process industry. In industrial as well as in functional buildings. Siemens offers automation, drive, and low-voltage switching technology as well as industrial software from standard products up to entire industry solutions. The industry software enables our industry customers to optimize the entire value chain from product design and development through manufacture and sales up to after-sales service. Our electrical and mechanical components offer integrated technologies for the entire drive train from couplings to gear units, from motors to control and drive solutions for all engineering industries. Our technology platform TIP offers robust solutions for power distribution. The high quality of our products sets industry-wide benchmarks. High environmental aims are part of our eco-management, and we implement these aims consistently. Right from product design, possible effects on the environment are examined. Hence many of our products and systems are RoHS compliant (Restriction of Hazardous Substances). As a matter of course, our production sites are certified according to DIN EN ISO 14001, but to us, environmental protection also means most efficient utilization of valuable resources. The best example are our energy-efficient drives with energy savings up to 60 %. Check out the opportunities our automation and drive solutions provide. And discover how you can sustainably enhance your competitive edge with us. Siemens LV 70 2009 1/3
Low-Voltage Controls and Distribution. The basis for progressive solutions. Extremely high demands are made on modern low-voltage controls and distribution: users want cost-effective solutions that are easy to integrate in control cabinets, distribution boards and distributed systems and can communicate perfectly with each other. Siemens has the answer: SIRIUS industrial controls and the low-voltage power distribution with Power Management, SIVACON and SENTRON. SIRIUS industrial controls The SIRIUS range has everything you need for switching, protecting and starting loads. Products for monitoring, control, detection, commanding, signaling and power supply round off the spectrum of industrial controls. Combined with Totally Integrated Automation, Safety Integrated and ECOFAST, our product portfolio can be bundled to create optimized systems. All in all, Siemens provides innovative controls with modern features, such as integrated communication and safety technology that work to your advantage: The basis for ground-breaking integrated solutions. Low-voltage power distribution with Power Management, SIVACON and SENTRON Non-residental buildings and industrial plants have one thing in common: without electricity, everything comes to a halt. The availability, safety and cost effectiveness of the power distribution system is of utmost importance from the medium voltage supply point through to the socket outlet. And only integrated solutions can ensure maximum efficiency for planning, configuration and operation. The concept is called Totally Integrated Power from Siemens. Total integration in planning and configuration creates synergies and saves costs. Perfectly matched products and systems provide efficient engineering and reliable operation. 1/4 Siemens LV 70 2009
Siemens LV 70 2009 1/
Busbar trunking systems in action. SIVACON 8PS. Busbar trunking systems in the low-voltage range guarantee the reliable transmission and distribution of power from the transformer through the main distribution board to the load. Siemens offers a complete range of high-performance systems: CD-L for 2 A and 40 A BD01 for 40 A to 160 A BD2 for 160 A to 120 A LR for 630 A to 6300 A LD for 1100 A to 000 A LX for 800 A to 6300 A The BD01 system is quickly mounted and ideal for power distribution in craft businesses and the skilled trades, e.g. in photographic studios. All busbar trunking systems are "Type-tested low-voltage controlgear assemblies" (TTA) according to IEC/EN 60439-1 and -2. They thus provide a safety standard which meets the high demands of automated production facilities and building management systems. Other advantages: Well arranged network topology Easy retrofitting when loads change Low operating costs thanks to high availability Easy planning and mounting The ideal system for production lines needing a great deal of power is the LD system up to 000 A. Area-wide solutions for lighting systems and small loads Be it in furniture stores, supermarkets or greenhouses with the CD-L system (up to 40 A) you can easily mount and supply power to lighting systems over large areas. The attractive design of the busbar trunking systems is very suitable for sales rooms open to the public. Its high degree of protection allows the CD-L system to be used even in harsh environments. Power for loads with no fixed location The BD01 system is ideal for power distribution (up to 160 A) in craft businesses and the skilled trades. The trunking units can be easily and quickly connected. An anti-rotation element in the tap-off units prevents incorrect mounting and guarantees easy conversion. Other advantages: Minimum stock keeping and straightforward planning thanks to one standard size for five different current levels. Universal power distribution The BD2 system (up to 120 A) supplies power to medium-size loads in buildings and all sectors of industry. Pre-assembled tap-off units with the most diverse equipment enable universal use. With only two standard sizes for all levels of current, stock keeping and planning are greatly facilitated. 1/6 Siemens LV 70 2009
Siemens offers modular ancillary equipment units for indication, control and monitoring of the flow of power through busbar trunking systems. These units are equipped with bus interfaces, command devices and power meters. In the petrochemical industry, it is the LR system that provides reliable and fault-free power supply. The LX busbar trunking system is the perfect equipment for multi-storey buildings where large quantities of power need to be transported, uninfluenced by the mounting position of the system. High availability in production The ventilated LD system (up to 000 A) conveys electricity to production facilities with a high demand for power, e.g. in the automobile industry. A separate PE bar enables the assured response of the protective device over long conducting paths. The high short-circuit resistance permits protection by medium-voltage circuit breakers for the conveyance of power between the transformer and the main infeed. Tap-off units up to 120 A can be plugged in without causing any problems. Flexible power distribution for multi-storey buildings The LX sandwich-style system (up to 6300 A) is used wherever large quantities of power have to be conveyed independently of the mounting position. Be it for radio broadcasting stations, computer centers or Internet providers conductor configurations with an insulated PE/ ground conductor and double neutral conductor cross-section guarantee an interference-free power supply. Tap-off units up to 120 A are available as standard. Safe power transmission for petrochemicals The encapsulated LR system (up to 6300 A) is extremely resistant to external interference thanks to its high degree of protection. It guarantees the safe conveyance of power in severe weather as well as under harsh industrial conditions with dust, dirt and aggressive media. Typical applications are the petrochemical industry, waste incineration plants and power stations. Siemens LV 70 2009 1/7
Made-to-measure, economical solutions. SIVACON 8PS Engineering Tools. SIVACON Engineering Tools from Siemens help generate precisely dimensioned and efficient solutions in planning and design. You are in full control of even complex tasks at all times. In MobileSpice, you select the trunking units for your system from a menu, and then transfer them into an order list. Selection aid for busbar trunking systems (MobileSpice) The selection aid enables you to order busbar trunking systems up to 120 A and is available in the Mall. The same selection aid can also be found in Catalog CA 01 on DVD. The following configurators are available: SIVACON 8PS system CD-L, 2 A and 40 A SIVACON 8PS system BD01, 40 A to 160 A SIVACON 8PS system BD2, 160 A to 120 A Should you have any queries concerning installation, functionality or application options please mail us at sbts.tool_support.aud@siemens.com We will be pleased to assist you. 1/8 Siemens LV 70 2009
Busbar Trunking Systems, Overview 2 Contents 2/2 Overview System overview 2/4 Overview 2/ Benefits 2/ More information Features overview 2/6 Overview Principles of busbar trunking planning 2/8 Overview Communication-capable busbar trunking systems for industry and buildings 2/9 Overview 2/10 Application Busbars instead of cables 2/11 Overview Siemens LV 70 2009
Busbar Trunking Systems, Overview Contents Overview Busbar trunking systems This catalog contains: 7 CD-L system up to 40 A 7 BD01 system up to 160 A 7 BD2 system up to 120 A Systems up to 6300 A on request. 2 Trunking unit with tap-off unit Feeder unit (end feeder unit) 2/2 Siemens LV 70 2009
Busbar Trunking Systems, Overview Contents CD-L system 2 A and 40 A BD2 system 160 A to 120 A G_NSV0_0162 NSV0_00421 Page System overview of busbar trunking systems 2/4 Technical overview of busbar trunking systems 2/6 Contents: CD-L system 3/1 Overview 3/2 Design 3/3 Technical specifications 3/10 Selection and ordering data 3/12 Configuration 3/32 Dimensional drawings 3/39 Page System overview of busbar trunking systems 2/4 Technical overview of busbar trunking systems 2/6 Contents: BD2 system /1 Overview /2 Design /4 Technical specifications /14 Selection and ordering data /22 Configuration /73 Fire protection /94 Dimensional drawings /102 2 BD01 system 40 A to 160 A NSV0_00241 Page System overview of busbar trunking systems 2/4 Technical overview of busbar trunking systems 2/6 Contents: BD01 system 4/1 Overview 4/2 Design 4/3 Technical specifications 4/9 Selection and ordering data 4/11 Configuration 4/29 Dimensional drawings 4/34 Siemens LV 70 2009 2/3
D 0 1 -K D B 1 0 0 1 D -K Busbar Trunking Systems, Overview System overview Overview 2 B B B B 2/4 Siemens LV 70 2009
Busbar Trunking Systems, Overview System overview Benefits $ CD-L system up to 40 A The versatile busbar trunking system for area-wide power supply to lighting systems: Versatile thanks to high degree of protection IP Lower planning costs through simple configuration Quick-release plug-in connection for fast assembly Variable changes of direction Tap-off points on both sides for optimized utilization of the busbar line Uniform current loading of the conductors through splitting of the tap-off plugs among the individual phases Tap-off plugs allow fast and flexible load relocation % BD01 system up to 160 A The busbar trunking system for power conveyance in craft business and the skilled trades: High degree of protection up to IP Flexible power supply Easy and quick planning Time-saving mounting Reliable mechanical and electrical connection High stability, low weight Few basic modules required Storage-friendly system Variable changes of direction Versatile tap-off units Positive opening and closing of tap-off points & BD2 system up to 120 A The busbar trunking system for operation in the harsh industrial world: High degree of protection up to IP Easy and quick planning Time-saving and economical mounting Reliable and safe operation Flexible modular system with simple solutions for every application Early planning of the power distribution system without exact knowledge of load locations Early readiness for operation thanks to fast and simple mounting Innovative design: No more compensation boxes to compensate elongation. Codable tap-off units and tap-off points Sealable throughout ( LD system up to 000 A The busbar trunking system for optimized power distribution in industry: High degree of protection IP4 Quick and easy mounting Reliable and safe operation Space-saving, compact design up to 000 A in one enclosure Load outgoing feeders up to 120 A Type-tested connection to distribution boards and transformers ) LX system up to 6300 A The busbar trunking system for power transmission and distribution in buildings: High degree of protection up to IP Quick and easy mounting Reliable and safe operation Load outgoing feeders up to 120 A Type-tested connection to distribution boards and transformers LR system The busbar trunking system for power transmission under extreme ambient conditions (IP68). Detailed information about this system is available from the Siemens branch located close to you. * Communication-capable busbar trunking systems Communication-capable function expansions for combination with known tap-off units: Can be used with the systems BD01, BD2, LD and LX Applications: - Lighting control for large areas - Remote switching and signaling in the industrial sector - Consumption recording of decentral power outgoing feeders Connection to the bus systems EIB, AS-Interface and PROFIBUS Easy contacting of the bus cable by insulation displacement method Easy and quick planning Flexible expansions and modifications Module system Retrofitting of existing installations More information Selection aid for busbar trunking systems (MobileSpice) The selection aid enables you to order busbar trunking systems up to 120 A. The following configurators are available: SIVACON 8PS system CD-L, 2... 40 A SIVACON 8PS system BD01, 40... 160 A SIVACON 8PS system BD2, 160... 120 A This selection aid can be accessed through the A&D Mall and is also included in the catalog CA 01 on DVD. This DVD is available free of charge from your Siemens sales office. Manual Planning with SIVACON 8PS Busbar Trunking Systems up to 6300 A English: Order No. AE 0141117-01 German: Order No. AE 0141017-01 Leaflet Busway Systems for Safe and Flexible Power Distribution up to 6300 A English: Order No. E20001-A220-P309-V2-7600 German: Order No. E20001-A220-P309-V2 2 Siemens LV 70 2009 2/
Busbar Trunking Systems, Overview Features overview Overview 2 Busbar trunking systems Rated current Rated operational voltage CD-L 2 40 2 2 2 40 G_NSV0_0162 Frequency Number of active conductors Degree of protection Ambient temperature, min./max. A V AC Hz C 400 0... 60 On one side: IP /+40 2, 4, 6 On both sides: 2 2, 1 4 + 1 2, 2 4, 2 6 (PE = enclosure) BD01 40 63 100 12 160 NSV0_00241 400 0... 60 4 Up to IP (PE = enclosure) /+40 BD2A BD2C 160... 400, 630... 120 690 0... 60 Up to IP /+40 NSV0_00421 LDA1... LDA8 LDC2... LDC8 1100... 4000, 2000... 000 1000 0... 60 4 or Up to IP4 /+40 NSV0_00681 LXA01... LXA10 LXC01... LXC10 800... 400, 1000... 6300 1000 0... 60 3, 4,, 6 Up to IP (PE = enclosure) /+40 NSV0_00321 LRC01... LRC29 630... 6300 1000 0... 60 4, IP68 /+40 NSV0_0141 2/6 Siemens LV 70 2009
Busbar Trunking Systems, Overview Features overview Mounting position Edgewise 1. 2 3 Length Tap-off points Tap-off units Material Fire load Can be combined with communication-capable tap-off units for m kwh/m On one side: every 0.; 1 or 1. m On two sides: every 0.; 1 or 1. m Up to 16 A Insulated Cu conductors, painted sheetsteel enclosure On one side: 0.7 On both sides: 1. -- 2 Edgewise, flat (tap-off points downwards) 2 3 On one side every 0. or 1 m Up to 63 A Insulated aluminum or copper conductors, painted sheet-steel enclosure 0.76 Lighting control Edgewise, flat and vertical 0.... 3.2 None On two sides offset every 0.2 or 0. m Up to 630 A Al or Cu busbars, painted sheetsteel enclosure 0.6... 0.67 (without tap-off points) Lighting control, remote switching, signaling and consumption measurement Horizontal, edgewise and vertical 0.... 3.2 None On one side every 1 m On two sides every 1 m Up to 120 A Insulated aluminum or copper busbars, painted sheetsteel enclosure 4.16... 8.83 (without tap-off points) Remote switching, signaling and consumption measurement Horizontal, edgewise and vertical 0.3... 3 None On one side every 0. m On two sides every 0. m Up to 120 A Insulated Al or Cu busbars, painted aluminum enclosure 1.9... 11.07 (without tap-off points) Remote switching, signaling and consumption measurement Horizontal, edgewise and vertical 0.... 3 None On one side selectable Up to 630 A Epoxy resin system, Cu busbars -- -- Siemens LV 70 2009 2/7
Busbar Trunking Systems, Overview Principles of busbar trunking planning 2 Overview Trunking units for currents from 40 to 6300 A When it comes to developing a power distribution concept, including the configuring of systems and components, it is necessary to coordinate the requirements and possibilities of the end-user with those of the manufacturer. With this in mind, the individual systems are described along with their technical features and applications. Another element is the graphic representation of the various busbar trunking elements. All details of importance for the planning work are specially emphasized and explained. You will find ideas for a ready-to-use planning solution in chapters 3 to under "Configuration information". For example, dimensioning principles are presented and in-depth information given on subjects such as system design, short-circuit protection, fire protection through compartmentalization or functional endurance. Services and engineering tools are available from Siemens to simplify the drawing up of customer specifications. General information When developing the planning concept of a power supply system it is necessary not only to consider the standards and specifications in force but also to clarify the correlations between economy and technology. Electrical equipment such as distribution boards and transformers must be dimensioned and selected so that they represent an optimum in their entirety and not just individually. All components must be sufficiently dimensioned for the loads which arise in the event of a fault as well as during operation at rated values. Other decisive points to be considered when drawing up the power concept are: The type, utilization and shape of building (e.g. high-rise, flat-roof and number of storeys) Determination of load centers and fixing of possible supply routes and locations for transformers and main distribution boards Fixing of building-related rating values according to specific area loads depending on the building's use Specifications and requirements imposed by the building authorities Requirements imposed by the power supply companies The result will never be a single solution but several versions which must be assessed with regard to their technical and economic implications. The following requirements are paramount in this connection: Easy and clear-cut planning Long endurance High availability Low fire load Flexible adaptation to alterations inside the building In most applications these requirements are easily met by the use of suitable busbar trunking systems. For this reason, busbar trunking systems rather than the cable installation method is being used more and more often by engineering offices for the conveyance and distribution of power. Siemens offers busbar trunking systems from 2 to 6300 A: The CD-L busbar system from 2 to 40 A for supplying power to lights and miniature loads The BD01 busbar system from 40 to 160 A for supplying power to workshops with tap-off units up to 63 A The BD2 system from 160 to 120 A for supplying power to medium-size loads in buildings and in industry The LD system for supplying power to loads with medium power consumption and in industry The LX sandwich system for the distribution of large amounts of power in buildings The LR encapsulated system for the conveyance of power in extreme ambient conditions (IP68) 2/8 Siemens LV 70 2009
Busbar Trunking Systems, Overview Communication-capable busbar trunking systems for industry and buildings Overview Busbar trunking systems The strengths of busbar trunking systems lie in the conveyance and distribution and the switching and protecting of electrical power. The integration of automation and building management systems in the Siemens busbar trunking systems results in additional benefits and at the same time increases the flexibility of the busbar trunking. The combination of standard tap-off units with standard ancillary equipment units ensures efficiency particularly in planning, installation and operation. Advantages of the system solution during planning: Modular system Tested standard components Free choice of bus system Use of common bus systems Advantages of the system solution during start-up: Easy and quick installation Start-up in steps possible Flexible in case of expansions and modifications Advantages of the system solution during operation: Transparency of switching states Central recording of power costs Increase in plant availability as a result of immediate detection of the type of fault and its location Preventive maintenance through recording of operating hours and operating cycles System concept of communication-capable busbar trunking systems Switching and reporting with the BD2 system The standardized tap-off units of the busbar trunking systems can be combined with standard types of ancillary equipment units to form a system solution of communication-capable busbar trunking. The standard applications are assembled at the factory from a combination of tap-off unit and ancillary equipment unit. The bus cable for transmitting the data signals is laid in a cable duct which must be mounted on the trunking unit. 2 Siemens LV 70 2009 2/9
Busbar Trunking Systems, Overview Communication-capable busbar trunking systems for industry and buildings 2 Application Standard application: lighting control The lighting control application enables the efficient and lowcost implementation of lighting control systems for large areas such as are used, for example, in supermarkets, furniture stores or DIY centers. The power bus is formed by BD01 or BD2 busbar trunking systems from Siemens, depending on the current requirement. The standard tap-off units are equipped with miniature circuit breakers or fuses and feed CD-L busbar systems which act simultaneously as the support system for the lighting elements. The economical and efficient control of extensive lighting systems is thus possible. The EIB (European Installation Bus) or AS-Interface bus systems are suitable for standard applications. On live busbar systems the tap-off point for power and bus can be adapted to the operational requirements. Possible functions of the lighting control Three times single-pole switching (L1, L2, L3) or 1/3, 2/3, 3/3 control Feedback of switching states Lamp test Recording of operating hours and operating cycles Standard application for consumption recording The consumption recording function enables the central recording of distributed power meters. The time-consuming reading of local meters is no longer necessary. Integration of the consumption recording in a visualization or I&C system by means of the data bus creates maximum transparency in the power distribution board. If recorded continuously, the measured values collected can be assigned to cost centers at a central point. The evaluation of trends and histories enables the data acquired to be analyzed. The combinations of tap-off unit and ancillary equipment unit can be equipped with either calibrated or non-calibrated power meters and enable the quick and transparent presentation of power consumption levels at the power tap-off points. The power bus is formed by BD2, LD or LX busbar trunking systems from Siemens, depending on the current requirement. Transformer sets (non-calibrated and calibrated) are available for the various tap-off units and levels of current. Possible functions for consumption recording Recording of consumption data Resetting of meter total Indication of a group fault Indication in the event of meter overflow, calling up of historical data Standard application for switching and reporting The application for switching and reporting enables the remote switching and remote monitoring of power or motor outgoing feeders. The power supply becomes highly transparent through the central recording of switching and operating states. In the event of a fault, the type of fault, e.g. short-circuit or overload tripping, and its location are detected quickly and efficiently so that the availability of the power supply system is effectively increased. The power bus is formed by BD2, LD or LX busbar trunking systems from Siemens, depending on the current requirement. The combinations of standard tap-off unit and standard ancillary equipment unit are equipped with corresponding switching devices and enable the centrally controlled switching and monitoring of the circuit breakers. The AS-Interface or PROFIBUS bus systems are suitable for standard applications. Possible functions for switching and reporting Central recording of switching and operating states Local and central switching Switching on is monitored by means of an integrated run-time monitor Fault signal inputs Group fault signal Short-circuit signal Overload signal Recording of operating hours and operating cycles Limit value signals 2/10 Siemens LV 70 2009
Busbar Trunking Systems, Overview Busbars instead of cables Overview Easier when it comes to planning Easy to plan, quick to install and flexible to use: Siemens busbar trunking systems are the economical answer for conveying power into any building. The power distribution system can be precisely planned from the total load rating and the type and number of loads. Clarity is assured by the line-shaped network topology with regularly arranged load feeders. All applications can be implemented in less time and space with standardized sizes. Quicker when it comes to installing Benefits during installation: Busbar trunking systems can be installed by two persons, saving time and money compared to the costly cable installation method. Installation errors are practically ruled out by the safe and user-guided connection technology. No special tools are required. Another benefit for quick installation: Siemens busbar trunking systems are easy to fasten and have large intervals between supports (busbars up to 4 m, cables every 1. m). Siemens busbar trunking systems are an economical alternative to the cable installation method. High short-circuit strength and minimum fire load result in greater safety A step-ahead in terms of safety be it short-circuit strength or fire load. For example, the BD2A-20 busbar trunking systems have a fire load of only 1.32 kwh/m; comparable cables (NYY 4 9/0 mm 2 ) have.19 kwh/m by contrast. And the busbars are halogen-free. Siemens busbar trunking systems have a high short-circuit strength. Also, the near-load protection against short-circuiting simplifies troubleshooting. 2 High fire load with cables With cable installation, new loads are connected by way of an additional sub-distribution board, which is costly and time-consuming Tap-off units near the loads make local arrangements more transparent Low fire load with busbar trunking system More flexible in case of expansions and modifications If the power distribution system has to be adapted to new requirements, the busbar will take you quicker to your goal. For example, new tap-off units can simply be mounted on the tap-off points. The system can be expanded and modified without difficulty. Tap-off units and system parts increase the flexibility. Cost-intensive downtimes are eliminated or minimized. The power distribution system enables faultless operation with high user-friendliness and safety. Siemens LV 70 2009 2/11
Busbar Trunking Systems, Overview Notes 2 2/12 Siemens LV 70 2009
CD-L System 2... 40 A 3 Introduction 3/2 Overview 3/3 Benefits 3/4 Design 3/8 Accessories General data 3/10 Technical specifications Trunking units 3/12 Selection and ordering data Feeder units 3/18 Overview 3/18 Selection and ordering data End flanges 3/22 Overview 3/22 Selection and ordering data Junction units 3/24 Overview 3/24 Selection and ordering data Tap-off plugs 3/26 Selection and ordering data Accessories 3/30 Selection and ordering data Configuration information 3/32 Overview 3/33 Design 3/37 Function Project planning aids 3/39 Dimensional drawings Siemens LV 70 2009
CD-L System 2... 40 A Introduction Overview 3 Entry feeder unit Universal suspension bracket CD-L busbar trunking unit Cable duct Standard fixing bracket Fixing bracket for cable duct Flexible junction unit Tap-off plug Fixing bracket with hook End flange 3/2 Siemens LV 70 2009
CD-L System 2... 40 A Introduction Version Type-tested low-voltage switchgear and controlgear assembly (TTA) according to IEC/EN 60439-1 IEC/EN 60439-2 Degree of protection High degree of protection to IP of the standard version Components Trunking units Insulated round conductors, one-side arrangement: 3-, -, 7-conductor system Insulated round conductors, two-side arrangement: 2 x 3-, 1x - / 1 x 3-, 2 x - and 2 x 7-conductor system Number and arrangement of the tap-off points: Benefits 7 Lower planning costs through simple configuration 7 Quick-release plug-in connection for fast assembly 7 Tap-off points on two sides for optimized utilization of the busbar line 7 Variable change of the direction of the busbar line 7 Uniform current loading of the conductors through splitting of the tap-off plugs among the individual phases 7 Tap-off plugs allow fast and flexible load relocation 7 Degree of protection to IP for extreme ambient conditions Length of trunking unit Plug-in connection Standard tap-off points Coded tap-off points Feeder units Entry feeder units End feeder units End flanges Number of tap-off points Equipment on one side Equipment on two sides Spacing of tap-off points m m 3 6, 3 or 2 2 (6, 3 or 2) 0., 1 or 1. 2 2 2 2 1 1. 2 2 2 1 3 Junction units Flexible junction units Tap-off plugs 3-pole, 10 A and 16 A, Lx (phase can be plugged over optionally to L1, L2, L3), N and PE -pole, 10 A, L1, L2, L3, N, PE 3-pole + L4/L, 10 A (N/L1, N/L2 or N/L3) + L4/L + PE Standard and coded versions Mobile N and L contacts Accessories Fixing bracket Suspension hook Suspension bracket Cable duct Cable duct mounting Cover for tap-off point Siemens LV 70 2009 3/3
CD-L System 2... 40 A Introduction Design Trunking units Connections A B 3 G_NSV0_0101 Trunking units The trunking units are available in 1., 2 and 3 meter lengths. They consist of a square, galvanized metal enclosure with white (RAL 9016) painted or unpainted finish. They are equipped on one side or two sides with insulated round conductors: 2 conductors for L3 + N (PE = enclosure), one-side or two-side 4 conductors for L1 + L2 + L3 + N (PE = enclosure), one-side or two-side 6 conductors for L4 + L1 + L2 + L3 + N + L (PE = enclosure). PE L4 L3 L2 L1 N L G_NSV0_0102 L3 N2 PE L4 L3 L3 N2 L2 L1 N L G_NSV0_0103 Conductor arrangement, one-side and two-side The tap-off points are spaced at regular intervals of 0. m, 1 m or 1. m on the trunking unit. The trunking unit enclosure acts as the PE conductor. 2 current strengths are available: 2 A, 2 2 A, 40 A and 2 40 A. All trunking units are equipped with finger-safe tap-off points. L N L1 L2 L3 L4 PE N2 L3 G_NSV0_0104 Plug-in connection The trunking units, including those with feeder units and end flanges, are assembled by a straightforward plug-in connection and fixing by a screw. The PE path is established automatically when the enclosures are connected. An interlock mechanism with two fixings prevents a loosening of the connections between the trunking units, feeder unit and flange. The fixing prevents the connection from becoming undone. No expansion compensation is required. Feeder units G_NSV0_0110 G_NSV0_0111 Feeder units, one-side and two-side The feeder units are used to feed the cable and are available as entry and end feeder units and are connected with the corresponding end of the straight element (the entry feeder unit with fixing screw and without connecting flange, the end feeder unit with connecting flange). Two versions are available in various conductor arrangements: As an entry feeder unit (EA) for 2 A, 2 2 A, 40 A and 2 40 A, As an end feeder unit (EE) for 2 A, 2 2 A, 40 A and 2 40 A. Cable entry from 1 side; use cable gland made of plastic, metric M2 or M32 with strain relief (not included in scope of supply). 3/4 Siemens LV 70 2009
CD-L System 2... 40 A Introduction End flanges Tap-off plugs Insulated tap-off plugs are used for taking current from the tapoff points on the trunking units. They can be mounted and removed by hand. This is even possible with live busbars. Standard tap-off plugs G_NSV0_0108 End flanges, one-side and two-side The end flanges serve as touch protection at the end of the busbar trunking line opposite to the feeder unit. They are available in two versions for connecting with the corresponding straight element. End flange (EA-EF); can be used if the cable line begins with an entry feeder unit, End flange (EE-EF); can be used if the cable line begins with an end feeder unit. Junction units G_NSV0_0106 G_NSV0_0109 G_NSV0_0107 Junction units, one-side and two-side The flexible junction units enable a change of the busbar line progression in each direction and also used for bridging obstacles along the busbar. G_NSV0_0112 Standard tap-off plug Single-phase tap-off plugs with transparent top part to allow pole selection are available. They can be used on standard tap-off points or coded tap-off points. Standard tap-off plugs are identified by a gray base. The tap-off plugs are available in the following versions: 3-pole, without fuse, 16 A, Lx (phase can be changed optionally to L1, L2, L3 ), N and PE 3-pole, with fuse, 16 A and 6.3 A, Lx (phase can be changed optionally to L1, L2, L3 ), N and PE The tap-off plugs can be equipped with L4/L contacts to be used on the 7-conductor and 7+7-conductor trunking units. Phase selection allows wiring of either single-phase circuits with separate neutral conductor (N/L1, N/L2, N/L3) or three-phase circuits with common neutral conductor (N/L1/L2/L3). Standard tap-off plugs are fitted with a neutral conductor and a phase contact; with the withdrawable version of an additional mobile contact they can be used as tap-off plugs for three-phase circuits. 7 Mobile contacts 3 G_NSV0_0113 G_NSV0_0114 G_NSV0_011 G_NSV0_0116 Mobile contacts, with and without fuse They are intended for use in the tap-off plugs with phase selection to feed three-phase circuits. 1-pole, 16 A, without fuse (blue color for the neutral conductor) 1-pole, 16 A, without fuse (black color for the phase) 1-pole, 10 A, with phase melting fuse 6.3 A ( mm x 20 mm) 1-pole, 16 A with phase melting fuse 10 A (8. mm x 31. mm) Siemens LV 70 2009 3/
CD-L System 2... 40 A Introduction Factory-wired standard tap-off plugs 7 Factory-wired tap-off plugs (2 conductors + PE) The standard version is designed for 10 A and fitted with 1 m long 3 x 1 mm² FROR cable, with four circuit configurations: N/L1, N/L2, N/L3, N2/L3. The top part of the tap-off plug is orange and the base can have different colors, depending on the wired circuit. Circuit configuration Top part Base N/L1 Orange Gray N/L2 Orange Green N/L3 Orange Black N2/L3 Orange Brown 7 Factory-wired tap-off plugs (2 conductors + L4/L + PE) The standard version is designed for 10 A and fitted with 2 m long x 1 mm² FROR cable, with three circuit configurations: N/L1 + L4/L, N/L2 + L4/L, N/L3 + L4/L. The top part of the tap-off plug is black and the base can have different colors, depending on the wired circuit. Circuit configuration Top part Base N/L1 + L4/L Black Gray N/L2 + L4/L Black Green N/L3 + L4/L Black Black G_NSV0_0122 G_NSV0_0123 G_NSV0_0117 G_NSV0_0118 3 G_NSV0_0124 G_NSV0_0119 G_NSV0_0120 Standard tap-off plugs They can be used on standard tap-off points or coded tap-off points. 7 Factory-wired tap-off plugs (4 conductors + PE) The standard version is designed for 10 A and fitted with 2 m long x 1 mm² FROR cable, with the circuit configuration: N/L1/L2/L3, the top part and the base of the tap-off plug is orange. Standard tap-off plugs These tap-off plugs are used in 7-conductor and 7+7-conductor trunking units. They can be used on standard tap-off points or coded tap-off points. 7 Factory-wired tap-off plugs (L4/L + PE) The standard version is designed for 10 A and fitted with 1 m long 3 x 1 mm² FROR cable, with the circuit configuration: L4/L. The top part and the base of the tap-off plug are orange. Circuit configuration Top part Base L4 / L Orange Orange Circuit configuration Top part Base N/L1, L2, L3 Orange Orange G_NSV0_012 G_NSV0_0121 Standard tap-off plug They can be used on standard tap-off points or coded tap-off points. Standard tap-off plug These tap-off plugs are used in 7-conductor and 7+7-conductor trunking units. They can be used on standard tap-off points or coded tap-off points. 3/6 Siemens LV 70 2009
CD-L System 2... 40 A Introduction Coded tap-off plugs Single-phase tap-off plugs with transparent top part to allow pole selection are available. The base can be red (KR) or white (KW). These tap-off plugs are mechanically coded and can only be used on coded tap-off points. The (KR) tap-off plugs (red base) can only be used on busbar systems with red tap-off point (KR version). The (KW) tap-off plugs (white base) can only be used on busbar systems with white tap-off point (KW or KRW version). Circuit configuration Top part Base N/L1 Red Gray N/L2 Red Green N/L3 Red Black N2/L3 Red Brown G_NSV0_0128 G_NSV0_0129 G_NSV0_0126 G_NSV0_0127 Coded tap-off plugs The tap-off plugs are available in the following versions: 3-pole, without fuse, 16 A, Lx (phase can be changed optionally to L1, L2, L3), N and PE 3-pole, with fuse, 16 A and 6.3 A, Lx (phase can be changed optionally to L1, L2, L3), N and PE Tap-off plugs can be equipped with L4/L contacts to be used with the 7-conductor and 7+7-conductor trunking units. Phase selection allows wiring of either single-phase circuits with separate neutral conductor (N/L1, N/L2, N/L3) or three-phase circuits with common neutral conductor (N/L1/N2/L3). Standard tap-off plugs are fitted with a neutral conductor and a phase contact, but with the withdrawable version of an additional mobile contact (see page 3/), can be used as tap-off plugs for three-phase circuits. Coded, wired tap-off plugs 7 Factory-wired coded tap-off plugs (2 conductors + PE) KR The standard version is designed for 10 A and fitted with 1 m long 3 x 1 mm² FROR cable, with four circuit configurations: N/L1, N/L2, N/L3, N2/L3. The top part of the tap-off plug is orange and the base can have different colors, depending on the wired circuit. G_NSV0_0130 G_NSV0_0131 Coded tap-off plugs These mechanically coded tap-off plugs can only be used on coded tap-off points (colored red, KR version). 7 Factory-wired coded tap-off plugs (2 conductors + PE) KW The standard version is designed for 10 A and fitted with 1 m long 3 x 1 mm² FROR cable, with four circuit configurations: N/L1, N/L2, N/L3, N2/L3. The top part of the tap-off plug is white and the base can have different colors, depending on the wired circuit. Circuit configuration Top part Base N/L1 White Gray N/L2 White Green N/L3 White Black N2/L3 White Brown 3 G_NSV0_0132 G_NSV0_0133 G_NSV0_0134 G_NSV0_013 Coded tap-off plugs These mechanically coded tap-off plugs can only be used on coded tap-off points (colored white, KW version). Siemens LV 70 2009 3/7
CD-L System 2... 40 A Introduction Accessories Suspension The trunking unit profile allows attachment of the suspension and fixing brackets at any point of the trunking unit. Standard fixing brackets Fixing brackets with hook G_NSV0_0141 G_NSV0_0142 3 G_NSV0_0137 G_NSV0_0138 Fixing brackets, one-side and two-side These brackets can be used: for mounting the trunking units on the floor or on the ceiling for suspending luminaires on the trunking unit. The fixing brackets are secured to the ceiling by chains or steel wire using suitable suspension brackets. Recommended spacing between fixing brackets 3 m. Available for loads up to 12 kg. Universal suspension brackets Fixing brackets with hook, one-side and two-side These brackets can be used: for mounting the trunking units on chains or steel wires, for suspending luminaires on the trunking unit. Open/closed hooks G_NSV0_0143 G_NSV0_0144 G_NSV0_0139 G_NSV0_0140 Hooks, open and closed These hooks can be used with the fixing/suspension brackets and fixing brackets for cable ducts: for mounting the trunking unit on the ceiling with chains or steel wires for suspending luminaires on the trunking unit. Suspension brackets, one-side and two-side These brackets can be used: for suspending the trunking units on the wall, on the floor or on the ceiling for suspending the luminaires. The suspension brackets are secured to the ceiling by chains or steel wire using suitable suspension brackets (open/closed). Recommended spacing between fixing brackets 3 m. Available for loads up to 2 kg. 3/8 Siemens LV 70 2009
CD-L System 2... 40 A Introduction Cable duct Cover G_NSV0_0136 G_NSV0_014 Cable duct (2 elements plugged together) The cable duct is made of plastic (white), standard length 3 m. It is used for cables in auxiliary circuits. It is mounted on the trunking unit with the fixing brackets for cable ducts. Fixing brackets for cable duct Cover The cover is used to restore degree of protection IP to the previously used tap-off point after an tap-off plug has been removed from an tap-off point. 3 G_NSV0_0146 Fixing bracket They are used with the standard fixing brackets or universal suspension brackets for mounting the trunking units of the cable ducts on the ceiling, on the floor or on the wall. Combined with the open/closed hooks, they can be secured on the ceiling with chains or steel wires. Siemens LV 70 2009 3/9
CD-L System 2... 40 A General data Technical specifications General technical specifications Type Trunking units CD-L-... Standards and specifications IEC/EN 60439-1 and -2 Rated insulation voltage U i V AC/DC 690 Overvoltage category/degree of pollution III/3 Rated operational voltage U e V AC 400 Frequency Hz 0... 60 Climatic proofing Damp heat, constant, to IEC 60068-2-78; Damp heat, cyclical, according to IEC 60068-2-30 Ambient temperature C -... +40 Degree of protection acc. to IEC/EN 6029 IP Material Trunking unit enclosures Galvanized, painted/unpainted sheet steel Busbars Insulated round-section copper wires Mounting position Edgewise; tap-off points at the side Weights See "Selection and Ordering Data" 3 Type CD-L-122 CD-L-124 CD-L-126 CD-L-222 CD-L-224 CD-L-224 CD-L-226 (/2) Conducting paths Rated insulation voltage U i V AC/DC 690 690 690 690 690 690 690 Overvoltage category/degree of pollution III/3 III/3 III/3 III/3 III/3 III/3 III/3 Rated operational voltage U e V AC 400 400 400 400 400 400 400 Frequency Hz 0... 60 0... 60 0... 60 0... 60 0... 60 0... 60 0... 60 Rated current I e conventional thermal current A 2 2 2 1) 2 2 2 2 2 2 2 2 1) at max. 40 C and 3 C on a 24 h average Impedance of conducting paths at 0 Hz and 20 C busbar temperature Resistance R 20 mω/m 6.2 6.2 6.2 6.2 6.2 6.2 6.2 Reactance X 20 mω/m 0.32 0.32 0.32 0.32 0.32 0.32 0.32 Impedance Z 20 mω/m 7.838 7.838 7.838 7.838 7.838 7.838 7.838 Impedance of conducting paths under event of a fault AC resistance R F mω/m 4.199 4.199 4.199 4.199 4.199 4.199 4.199 Reactance per unit length X F mω/m 0.600 0.600 0.600 0.600 0.600 0.600 0.600 Impedance per unit length Z F mω/m 4.241 4.241 4.241 4.241 4.241 4.241 4.241 Zero sequence impedance acc. to IEC/EN 60909 Resistance R 0 Phase to N mω/m 17.031 17.031 17.031 17.031 17.031 17.031 17.031 Reactance X 0 Phase to N mω/m 2.433 2.433 2.433 2.433 2.433 2.433 2.433 Impedance Z 0 Phase to N mω/m 17.204 17.204 17.204 17.204 17.204 17.204 17.204 Resistance R 0 Phase to PE mω/m 12.833 12.833 12.833 12.833 12.833 12.833 12.833 Reactance X 0 Phase to PE mω/m 1.833 1.833 1.833 1.833 1.833 1.833 1.833 Impedance Z 0 Phase to PE mω/m 12.963 12.963 12.963 12.963 12.963 12.963 12.963 Short-circuit strength Rated impulse withstand current I pk ka 4.8 4.8 4.8 4.8 4.8 4.8 4.8 Rated short-time withstand current I cw (t = 1 s) ka 3.1 3.1 3.1 3.1 3.1 3.1 3.1 Conductors Number of active conductors 2 4 6 2 2 1 4 2 4 2 6 1 2 Conductor cross-section N, L1, L2, L3 mm 2 2.4 2.4 2.4 2.4 2.4 2.4 2.4 L4, L mm 2 -- -- 2.4 -- -- -- 2.4 PE (enclosure) Cu mm 2 12 12 12 24 24 24 24 Conductor material Cu Cu Cu Cu Cu Cu Cu Fire load kwh/m 0.7 0.7 0.7 1. 1. 1. 1. Max. thermal load, I 2 t value A 2 s 10 3 230.4 230.4 230.4 230.4 230.4 230.4 230.4 Fixing intervals at normal mechanical load m 3 3 3 3 3 3 3 Position of tap-off points Depending on the type, on one side/two sides every 0. m, 1 m or 1. m 1) L4/L circuit: max. rated current 2 A. 3/10 Siemens LV 70 2009
CD-L System 2... 40 A General data Type CD-L-1402 CD-L-1404 CD-L-1406 CD-L-2402 CD-L-2404 CD-L-2404 CD-L-2406 (/2) Conducting paths Rated insulation voltage U i V AC/DC 690 690 690 690 690 690 690 Overvoltage category/degree of pollution III/3 III/3 III/3 III/3 III/3 III/3 III/3 Rated operational voltage U e V AC 400 400 400 400 400 400 400 Frequency Hz 0... 60 0... 60 0... 60 0... 60 0... 60 0... 60 0... 60 Rated current I e conventional thermal current A 40 40 40 40 1) 2 40 40 40 1) at max. 40 C and 3 C on a 24 h average Impedance of conducting paths at 0 Hz and 20 C busbar temperature Resistance R 20 mω/m 2.7 2.7 2.7 2.7 2.7 2.7 2.7 Reactance X 20 mω/m 0.2 0.2 0.2 0.2 0.2 0.2 0.2 Impedance Z 20 mω/m 3.23 3.23 3.23 3.23 3.23 3.23 3.23 Impedance of conducting paths under event of a fault AC resistance R F mω/m 0.82 0.82 0.82 0.82 0.82 0.82 0.82 Reactance per unit length X F mω/m 0.118 0.118 0.118 0.118 0.118 0.118 0.118 Impedance per unit length Z F mω/m 0.833 0.833 0.833 0.833 0.833 0.833 0.833 Zero sequence impedance acc. to IEC/EN 60909 Resistance R 0 Phase to N mω/m 8.03 8.03 8.03 8.03 8.03 8.03 8.03 Reactance X 0 Phase to N mω/m 1.147 1.147 1.147 1.147 1.147 1.147 1.147 Impedance Z 0 Phase to N mω/m 8.116 8.116 8.116 8.116 8.116 8.116 8.116 Resistance R 0 Phase to PE mω/m 7.210 7.210 7.210 7.210 7.210 7.210 7.210 Reactance X 0 Phase to PE mω/m 1.030 1.030 1.030 1.030 1.030 1.030 1.030 Impedance Z 0 Phase to PE mω/m 7.284 7.284 7.284 7.284 7.284 7.284 7.284 Short-circuit strength Rated impulse withstand current I pk ka 10.6 10.6 10.6 10.6 10.6 10.6 10.6 Rated short-time withstand current I cw (t = 1 s) ka 6.16 6.16 6.16 6.16 6.16 6.16 6.16 Conductors Number of active conductors 2 4 6 2 2 1 4 2 4 2 6 1 2 Conductor cross-section N, L1, L2, L3 mm 2 6.1 6.1 6.1 6.1 6.1 6.1 6.1 L4, L mm 2 2.4 2.4 PE (enclosure) Cu mm 2 12 12 12 24 24 24 24 Conductor material Cu Cu Cu Cu Cu Cu Cu Fire load kwh/m 0.7 0.7 0.7 1. 1. 1. 1. Max. thermal load, I 2 t value A 2 s 10 3 1123.6 1123.6 1123.6 1123.6 1123.6 1123.6 1123.6 Fixing intervals at normal mechanical load m 3 3 3 3 3 3 3 Position of tap-off points Depending on the type, on one side/two sides every 0. m, 1 m or 1. m 1) L4/L circuit: max. rated current 2 A. Feeder units, conductor cross-sections 3 Version Type N, L1, L2, L3 L4, L PE Tap-off plugs min. mm 2 max. mm 2 Entry feeder unit CD-L-...-EA 2. 6 (f) 10 (so, st) End feeder unit CD-L-...-EE 2. 6 (f) 10 (so, st) min. mm 2 max. mm 2 1. (f) 2. (so, st) 1. (f) 2. (so, st) f = finely stranded with end sleeve, so = solid, st = stranded Type CD-L-A... Version 3-, -pole or +2-pole Rated current I e A 6.3; 10 or 16 Switching capacity acc. to IEC/EN 60947-3 Utilization category AC-20B Connection With or without permanently attached cable; the PE is connected first when mounting the tap-off plug and is deconnected last when removing the tap-off plug Fuses With or without fuse holder for cylindrical fuses Size 8. mm 31. mm or mm 20 mm, type gg (IEC) or type gl (VDE) (quick) min. mm 2 max. mm 2 2. 4 (f) 6 (so, st) 2. 4 (f) 6 (so, st) Siemens LV 70 2009 3/11
CD-L System 2... 40 A Trunking units Selection and ordering data Unpainted trunking units with uncoded tap-off points (supplied from stock) 3 Version Length Conductor configuration Tap-off points DT Type Order No. PS* Weight Number Spacing per unit approx. m m kg Rated current I e = 2 A, tap-off points on one side Trunking units 3 3 conductors 2 1. X CD-L-122-3-1, 8PS0300-3BF2 6 units 2.770 Sheet-steel enclosure, 3 PE 3 1 X CD-L-122-3-1 8PS0301-3BF2 6 units 2.770 unpainted, L3 uncoded tap-off points 3 6 0. X CD-L-122-3-0, 8PS0302-3BF2 6 units 2.770 2 N 2 1 X CD-L-122-2-1 8PS0300-2BF2 6 units 1.840 1. 2 1 X CD-L-122-1,-1 8PS0300-1BF2 6 units 1.380 3 conductors 2 1. X CD-L-124-3-1, 8PS0300-3CF2 6 units 2.980 3 PE 3 1 X CD-L-124-3-1 8PS0301-3CF2 6 units 2.980 L3 L3 3 L2 N2 6 0. X CD-L-124-3-0, 8PS0302-3CF2 6 units 2.980 L1 2 N 2 1 X CD-L-124-2-1 8PS0300-2CF2 6 units 1.990 1. 2 1 X CD-L-124-1,-1 8PS0300-1CF2 6 units 1.490 G_NSV0_0147 3 7 conductors 1) 2 1. X CD-L-126-3-1, 8PS0300-3DF2 6 units 3.130 3 PE 3 1 X CD-L-126-3-1 8PS0301-3DF2 6 units 3.130 L4 L3 L3 3 L2 N2 6 0. X CD-L-126-3-0, 8PS0302-3DF2 6 units 3.130 L1 2 N 2 1 X CD-L-126-2-1 8PS0300-2DF2 6 units 2.080 L 1. 2 1 X CD-L-126-1,-1 8PS0300-1DF2 6 units 1.60 Rated current I e = 2 2 A, tap-off points on two sides Trunking units 3 2 3 conductors 2 x 2 1. X CD-L-222-3-1, 8PS0300-3FF2 6 units.30 Sheet-steel enclosure, 3 PE 2 x 3 1 X CD-L-222-3-1 8PS0301-3FF2 6 units.30 unpainted, L3 N uncoded tap-off points 3 2 x 6 0. X CD-L-222-3-0, 8PS0302-3FF2 6 units.30 2 N L3 2 x 2 1 X CD-L-222-2-1 8PS0300-2FF2 6 units 3.690 PE 1. 2 x 2 1 X CD-L-222-1,-1 8PS0300-1FF2 6 units 2.770 3 1 conductors 2 x 2 1. X CD-L-224/2-KR-3-1, 8PS0303-3GF2 6 units.740 3 1 3 conductors 2 x 3 1 X CD-L-224/2-KR-3-1 8PS0304-3GF2 6 units.740 3 2 x 6 0. X CD-L-224/2-KR-3-0, 8PS030-3GF2 6 units.740 2 2 x 2 1 X CD-L-224/2-KR-2-1 8PS0303-2GF2 6 units 3.830 1. 2 x 2 1 X CD-L-224/2-KR-1,-1 8PS0303-1GF2 6 units 2.870 PE L3 L3 N N2 L2 L1 N L3 G_NSV0_0148 G_NSV0_0149 G_NSV0_010 G_NSV0_011 G_NSV0_012 G_NSV0_013 PE 3 2 conductors 2 x 2 1. X CD-L-224-3-1, 8PS0300-3HF2 6 units.960 3 PE 2 x 3 1 X CD-L-224-3-1 8PS0301-3HF2 6 units.960 3 L3 N2 L3 L2 N L1 2 x 6 0. X CD-L-224-3-0, 8PS0302-3HF2 6 units.960 2 L1 L2 N2 N L3 L3 2 x 2 1 X CD-L-224-2-1 8PS0300-2HF2 6 units 3.970 1. PE 2 x 2 1 X CD-L-224-1,-1 8PS0300-1HF2 6 units 2.980 3 2 7 2 x 2 1. X CD-L-226-3-1, 8PS0300-3JF2 6 units 6.20 3 conductors 1) 2 x 3 1 X CD-L-226-3-1 8PS0301-3JF2 6 units 6.20 3 PE L3 L4 L3 L N 2 x 6 0. X CD-L-226-3-0, 8PS0302-3JF2 6 units 6.20 2 N2 L2 L1 L1 L2 N2 2 x 2 1 X CD-L-226-2-1 8PS0300-2JF2 6 units 4.170 1. N L3 L3 2 x 2 1 X CD-L-226-1,-1 8PS0300-1JF2 6 units 3.130 G_NSV0_014 G_NSV0_01 L L4 PE 1) L4/L circuit: max. rated current 2 A. 3/12 Siemens LV 70 2009 * You can order this quantity or a multiple thereof.
CD-L System 2... 40 A Trunking units Version Length Conductor configuration Tap-off points DT Type Order No. PS* Weight Number Spacing per unit approx. m m kg Rated current I e = 40 A, tap-off points on one side Trunking units 3 3 conductors 2 1. X CD-L-1402-3-1, 8PS0300-3BF40 6 units 2.960 Sheet-steel enclosure, 3 PE 3 1 X CD-L-1402-3-1 8PS0301-3BF40 6 units 2.960 unpainted, L3 uncoded tap-off points 3 6 0. X CD-L-1402-3-0, 8PS0302-3BF40 6 units 2.960 2 N 2 1 X CD-L-1402-2-1 8PS0300-2BF40 6 units 1.970 1. 2 1 X CD-L-1402-1,-1 8PS0300-1BF40 6 units 1.480 3 conductors 2 1. X CD-L-1404-3-1, 8PS0300-3CF40 6 units 3.330 3 PE 3 1 X CD-L-1404-3-1 8PS0301-3CF40 6 units 3.330 L3 L3 3 L2 N2 6 0. X CD-L-1404-3-0, 8PS0302-3CF40 6 units 3.330 L1 2 N 2 1 X CD-L-1404-2-1 8PS0300-2CF40 6 units 2.220 1. 2 1 X CD-L-1404-1,-1 8PS0300-1CF40 6 units 1.660 G_NSV0_0147 3 7 conductors 1) 2 1. X CD-L-1406-3-1, 8PS0300-3DF40 6 units 3.480 3 PE 3 1 X CD-L-1406-3-1 8PS0301-3DF40 6 units 3.480 L4 L3 L3 3 L2 N2 6 0. X CD-L-1406-3-0, 8PS0302-3DF40 6 units 3.480 L1 2 N 2 1 X CD-L-1406-2-1 8PS0300-2DF40 6 units 2.320 L 1. 2 1 X CD-L-1406-1,-1 8PS0300-1DF40 6 units 1.740 Rated current I e = 2 40 A, tap-off points on two sides Trunking units 3 2 3 conductors 2 x 2 1. X CD-L-2402-3-1, 8PS0300-3FF40 6 units.920 Sheet-steel enclosure, 3 PE 2 x 3 1 X CD-L-2402-3-1 8PS0301-3FF40 6 units.920 unpainted, L3 N uncoded tap-off points 3 2 x 6 0. X CD-L-2402-3-0, 8PS0302-3FF40 6 units.920 2 N L3 2 x 2 1 X CD-L-2402-2-1 8PS0300-2FF40 6 units 3.940 PE 1. 2 x 2 1 X CD-L-2402-1,-1 8PS0300-1FF40 6 units 2.960 3 1 conductors 2 x 2 1. X CD-L-2404/2-KR-3-1, 8PS0303-3GF40 6 units 6.290 3 1 3 conductors 2 x 3 1 X CD-L-2404/2-KR-3-1 8PS0304-3GF40 6 units 6.290 3 2 x 6 0. X CD-L-2404/2-KR-3-0, 8PS030-3GF40 6 units 6.290 2 2 x 2 1 X CD-L-2404/2-KR-2-1 8PS0303-2GF40 6 units 4.190 1. 2 x 2 1 X CD-L-2404/2-KR-1,-1 8PS0303-1GF40 6 units 3.140 PE L3 L3 N N2 L2 L1 N L3 G_NSV0_0148 G_NSV0_0149 G_NSV0_010 G_NSV0_011 G_NSV0_012 G_NSV0_013 PE 3 2 conductors 2 x 2 1. X CD-L-2404-3-1, 8PS0300-3HF40 6 units 6.60 3 PE 2 x 3 1 X CD-L-2404-3-1 8PS0301-3HF40 6 units 6.60 3 L3 N2 L3 L2 N L1 2 x 6 0. X CD-L-2404-3-0, 8PS0302-3HF40 6 units 6.60 2 L1 L2 N2 N L3 L3 2 x 2 1 X CD-L-2404-2-1 8PS0300-2HF40 6 units 4.440 1. PE 2 x 2 1 X CD-L-2404-1,-1 8PS0300-1HF40 6 units 3.330 3 2 7 2 x 2 1. X CD-L-2406-3-1, 8PS0300-3JF40 6 units 6.90 3 conductors 1) 2 x 3 1 X CD-L-2406-3-1 8PS0301-3JF40 6 units 6.90 3 PE L3 L4 L3 L N 2 x 6 0. X CD-L-2406-3-0, 8PS0302-3JF40 6 units 6.90 2 N2 L2 L1 L1 L2 N2 2 x 2 1 X CD-L-2406-2-1 8PS0300-2JF40 6 units 4.630 1. N L3 L3 2 x 2 1 X CD-L-2406-1,-1 8PS0300-1JF40 6 units 3.470 G_NSV0_014 G_NSV0_01 L L4 PE 3 1) L4/L circuit: max. rated current 2 A. * You can order this quantity or a multiple thereof. Siemens LV 70 2009 3/13
CD-L System 2... 40 A Trunking units Unpainted trunking units with codable tap-off points (supplied from stock) 3 Version Length Conductor configuration Tap-off points DT Type Order No. PS* Weight Number Spacing per unit approx. m m kg Rated current I e = 2 A, tap-off points on one side Trunking units 3 KR, 2 1. X CD-L-124-KR-3-1, 8PS0310-3CF2 6 units 2.980 Sheet-steel enclosure, 3 conductors 3 1 X CD-L-124-KR-3-1 8PS0311-3CF2 6 units 2.980 unpainted, coded tap-off points 3 PE 6 0. X CD-L-124-KR-3-0, 8PS0312-3CF2 6 units 2.980 L3 L3 2 L2 L1 N2 2 1 X CD-L-124-KR-2-1 8PS0310-2CF2 6 units 1.990 1. N 2 1 X CD-L-124-KR-1,-1 8PS0310-1CF2 6 units 1.490 G_NSV0_018 G_NSV0_0164 G_NSV0_0160 3 KW, 2 1. X CD-L-124-KW-3-1, 8PS0313-3CF2 6 units 2.980 3 conductors 3 1 X CD-L-124-KW-3-1 8PS0314-3CF2 6 units 2.980 3 PE 6 0. X CD-L-124-KW-3-0, 8PS031-3CF2 6 units 2.980 L3 L3 2 L2 L1 N2 2 1 X CD-L-124-KW-2-1 8PS0313-2CF2 6 units 1.990 1. N 2 1 X CD-L-124-KW-1,-1 8PS0313-1CF2 6 units 1.490 G_NSV0_0161 3 KR, 2 1. X CD-L-126-KR-3-1, 8PS0310-3DF2 6 units 3.130 3 7 conductors 1) 3 1 X CD-L-126-KR-3-1 8PS0311-3DF2 6 units 3.130 3 PE L4 6 0. X CD-L-126-KR-3-0, 8PS0312-3DF2 6 units 3.130 L3 L3 2 L2 L1 N2 2 1 X CD-L-126-KR-2-1 8PS0310-2DF2 6 units 2.080 1. N L 2 1 X CD-L-126-KR-1,-1 8PS0310-1DF2 6 units 1.60 G_NSV0_0162 3 KW, 2 1. X CD-L-126-KW-3-1, 8PS0313-3DF2 6 units 3.130 3 7 conductors 1) 3 1 X CD-L-126-KW-3-1 8PS0314-3DF2 6 units 3.130 3 PE L 6 0. X CD-L-126-KW-3-0, 8PS031-3DF2 6 units 3.130 L3 L3 2 L2 L1 N2 2 1 X CD-L-126-KW-2-1 8PS0313-2DF2 6 units 2.080 1. N L4 2 1 X CD-L-126-KW-1,-1 8PS0313-1DF2 6 units 1.60 G_NSV0_0163 Rated current I e = 2 2 A, tap-off points on two sides Trunking units 3 KR, 2 x 2 1. X CD-L-224/2-KR-3-1, 8PS0303-3GF2 6 units.740 Sheet-steel enclosure, 3 1 conductors 2 x 3 1 X CD-L-224/2-KR-3-1 8PS0304-3GF2 6 units.740 unpainted, 1 3 conductors coded tap-off points 3 2 x 6 0. X CD-L-224/2-KR-3-0, 8PS030-3GF2 6 units.740 PE 2 L3 L3 N 2 x 2 1 X CD-L-224/2-KR-2-1 8PS0303-2GF2 6 units 3.830 N2 L2 1. L1 2 x 2 1 X CD-L-224/2-KR-1,-1 8PS0303-1GF2 6 units 2.870 G_NSV0_019 G_NSV0_013 N L3 PE 3 KR/KW, 2 x 2 1. X CD-L-224-KRW-3-1, 8PS0316-3HF2 6 units.960 3 2 conductors 2 x 3 1 X CD-L-224-KRW-3-1 8PS0317-3HF2 6 units.960 3 PE L3 L3 N 2 x 6 0. X CD-L-224-KRW-3-0, 8PS0318-3HF2 6 units.960 2 N2 L2 L1 L1 L2 N2 2 x 2 1 X CD-L-224-KRW-2-1 8PS0316-2HF2 6 units 3.970 1. N L3 L3 2 x 2 1 X CD-L-224-KRW-1,-1 8PS0316-1HF2 6 units 2.980 G_NSV0_016 PE 3 KR/KW, 2 x 2 1. X CD-L-226-KRW-3-1, 8PS0316-3JF2 6 units 6.20 3 2 7 conductors 1) 2 x 3 1 X CD-L-226-KRW-3-1 8PS0317-3JF2 6 units 6.20 3 2 x 6 0. X CD-L-226-KRW-3-0, 8PS0318-3JF2 6 units 6.20 2 PE L3 L4 L3 L N 2 x 2 1 X CD-L-226-KRW-2-1 8PS0316-2JF2 6 units 4.170 1. N2 L2 L1 L1 L2 N2 2 x 2 1 X CD-L-226-KRW-1,-1 8PS0316-1JF2 6 units 3.130 G_NSV0_0166 N L L3 L3 L4 PE 1) L4/L circuit: max. rated current 2 A. 3/14 Siemens LV 70 2009 * You can order this quantity or a multiple thereof.
CD-L System 2... 40 A Trunking units Version Length Conductor configuration Tap-off points DT Type Order No. PS* Weight Number Spacing per unit approx. m m kg Rated current I e = 40 A, tap-off points on one side Trunking units 3 KR, 2 1. X CD-L-1404-KR-3-1, 8PS0310-3CF40 6 units 3.330 Sheet-steel enclosure, 3 conductors 3 1 X CD-L-1404-KR-3-1 8PS0311-3CF40 6 units 3.330 unpainted, coded tap-off points 3 PE 6 0. X CD-L-1404-KR-3-0, 8PS0312-3CF40 6 units 3.330 L3 L3 2 L2 L1 N2 2 1 X CD-L-1404-KR-2-1 8PS0310-2CF40 6 units 2.220 1. N 2 1 X CD-L-1404-KR-1,-1 8PS0310-1CF40 6 units 1.660 G_NSV0_018 G_NSV0_0164 G_NSV0_0160 3 KW, 2 1. X CD-L-1404-KW-3-1, 8PS0313-3CF40 6 units 3.330 3 conductors 3 1 X CD-L-1404-KW-3-1 8PS0314-3CF40 6 units 3.330 3 PE 6 0. X CD-L-1404-KW-3-0, 8PS031-3CF40 6 units 3.330 L3 L3 2 L2 L1 N2 2 1 X CD-L-1404-KW-2-1 8PS0313-2CF40 6 units 2.220 1. N 2 1 X CD-L-1404-KW-1,-1 8PS0313-1CF40 6 units 1.660 G_NSV0_0161 3 KR, 2 1. X CD-L-1406-KR-3-1, 8PS0310-3DF40 6 units 3.480 3 7 conductors 1) 3 1 X CD-L-1406-KR-3-1 8PS0311-3DF40 6 units 3.480 3 PE L4 6 0. X CD-L-1406-KR-3-0, 8PS0312-3DF40 6 units 3.480 L3 L3 2 L2 L1 N2 2 1 X CD-L-1406-KR-2-1 8PS0310-2DF40 6 units 2.320 1. N L 2 1 X CD-L-1406-KR-1,-1 8PS0310-1DF40 6 units 1.740 G_NSV0_0162 3 KW, 2 1. X CD-L-1406-KW-3-1, 8PS0313-3DF40 6 units 3.480 3 7 conductors 1) 3 1 X CD-L-1406-KW-3-1 8PS0314-3DF40 6 units 3.480 3 PE L 6 0. X CD-L-1406-KW-3-0, 8PS031-3DF40 6 units 3.480 L3 L3 2 L2 L1 N2 2 1 X CD-L-1406-KW-2-1 8PS0313-2DF40 6 units 2.320 1. N L4 2 1 X CD-L-1406-KW-1,-1 8PS0313-1DF40 6 units 1.740 G_NSV0_0163 Rated current I e = 2 40 A, tap-off points on two sides Trunking units 3 KR, 2 x 2 1. X CD-L-2404/2-KR-3-1, 8PS0303-3GF40 6 units 6.290 Sheet-steel enclosure, 3 1 conductors 2 x 3 1 X CD-L-2404/2-KR-3-1 8PS0304-3GF40 6 units 6.290 unpainted, 1 3 conductors coded tap-off points 3 2 x 6 0. X CD-L-2404/2-KR-3-0, 8PS030-3GF40 6 units 6.290 PE 2 L3 L3 N 2 x 2 1 X CD-L-2404/2-KR-2-1 8PS0303-2GF40 6 units 4.190 N2 L2 1. L1 2 x 2 1 X CD-L-2404/2-KR-1,-1 8PS0303-1GF40 6 units 3.140 G_NSV0_019 G_NSV0_013 N L3 PE 3 KR/KW, 2 x 2 1. X CD-L-2404-KRW-3-1, 8PS0316-3HF40 6 units 6.60 3 2 conductors 2 x 3 1 X CD-L-2404-KRW-3-1 8PS0317-3HF40 6 units 6.60 3 PE L3 L3 N 2 x 6 0. X CD-L-2404-KRW-3-0, 8PS0318-3HF40 6 units 6.60 2 N2 L2 L1 L1 L2 N2 2 x 2 1 X CD-L-2404-KRW-2-1 8PS0316-2HF40 6 units 4.440 1. N L3 L3 2 x 2 1 X CD-L-2404-KRW-1,-1 8PS0316-1HF40 6 units 3.330 G_NSV0_016 PE 3 3 KR/KW, 2 x 2 1. X CD-L-2406-KRW-3-1, 8PS0316-3JF40 6 units 6.90 3 2 7 conductors 1) 2 x 3 1 X CD-L-2406-KRW-3-1 8PS0317-3JF40 6 units 6.90 3 2 x 6 0. X CD-L-2406-KRW-3-0, 8PS0318-3JF40 6 units 6.90 2 PE L3 L4 L3 L N 2 x 2 1 X CD-L-2406-KRW-2-1 8PS0316-2JF40 6 units 4.630 1. N2 L2 L1 L1 L2 N2 2 x 2 1 X CD-L-2406-KRW-1,-1 8PS0316-1JF40 6 units 3.470 G_NSV0_0166 N L L3 L3 L4 PE 1) L4/L circuit: max. rated current 2 A. * You can order this quantity or a multiple thereof. Siemens LV 70 2009 3/1
CD-L System 2... 40 A Trunking units Painted trunking units with uncoded tap-off points (delivery on request) 3 Version Length Conductor configuration Tap-off points DT Type Order No. PS* Weight Number Spacing per unit approx. m m kg Rated current I e = 2 A, tap-off points on one side Trunking units 3 3 conductors 2 1. X CD-L-122-3-1,-L 8PS1300-3BF2 6 units 2.770 Sheet-steel enclosure, 3 PE 3 1 X CD-L-122-3-1-L 8PS1301-3BF2 6 units 2.770 painted, white (RAL 9016), L3 uncoded tap-off points 3 6 0. X CD-L-122-3-0,-L 8PS1302-3BF2 6 units 2.770 2 N 2 1 X CD-L-122-2-1-L 8PS1300-2BF2 6 units 1.840 1. 2 1 X CD-L-122-1,-1-L 8PS1300-1BF2 6 units 1.380 3 conductors 2 1. X CD-L-124-3-1,-L 8PS1300-3CF2 6 units 2.980 3 PE 3 1 X CD-L-124-3-1-L 8PS1301-3CF2 6 units 2.980 L3 L3 3 L2 N2 6 0. X CD-L-124-3-0,-L 8PS1302-3CF2 6 units 2.980 L1 2 N 2 1 X CD-L-124-2-1-L 8PS1300-2CF2 6 units 1.990 1. 2 1 X CD-L-124-1,-1-L 8PS1300-1CF2 6 units 1.490 G_NSV0_016 3 7 conductors 1) 2 1. X CD-L-126-3-1,-L 8PS1300-3DF2 6 units 3.480 3 PE 3 1 X CD-L-126-3-1-L 8PS1301-3DF2 6 units 3.480 L4 L3 L3 3 L2 N2 6 0. X CD-L-126-3-0,-L 8PS1302-3DF2 6 units 3.480 L1 2 N 2 1 X CD-L-126-2-1-L 8PS1300-2DF2 6 units 2.320 L 1. 2 1 X CD-L-126-1,-1-L 8PS1300-1DF2 6 units 1.740 Rated current I e = 2 2 A, tap-off points on two sides Trunking units 3 2 3 conductors 2 x 2 1. X CD-L-222-3-1,-L 8PS1300-3FF2 6 units.30 Sheet-steel enclosure, 3 PE 2 x 3 1 X CD-L-222-3-1-L 8PS1301-3FF2 6 units.30 painted, white (RAL 9016), L3 N uncoded tap-off points 3 2 x 6 0. X CD-L-222-3-0,-L 8PS1302-3FF2 6 units.30 2 N L3 2 x 2 1 X CD-L-222-2-1-L 8PS1300-2FF2 6 units 3.690 PE 1. 2 x 2 1 X CD-L-222-1,-1-L 8PS1300-1FF2 6 units 2.770 3 1 conductors 2 x 2 1. X CD-L-224/2-KR-3-1,-L 8PS1303-3GF2 6 units.740 3 1 3 conductors 2 x 3 1 X CD-L-224/2-KR-3-1-L 8PS1304-3GF2 6 units.740 PE 3 2 x 6 0. X CD-L-224/2-KR-3-0,-L 8PS130-3GF2 6 units.740 L3 L3 N N2 2 L2 2 x 2 1 X CD-L-224/2-KR-2-1-L 8PS1303-2GF2 6 units 3.830 L1 N L3 1. 2 x 2 1 X CD-L-224/2-KR-1,-1-L 8PS1303-1GF2 6 units 2.870 G_NSV0_017 G_NSV0_0149 G_NSV0_010 G_NSV0_011 G_NSV0_012 G_NSV0_013 PE 3 2 conductors 2 x 2 1. X CD-L-224-3-1,-L 8PS1300-3HF2 6 units.960 3 PE 2 x 3 1 X CD-L-224-3-1-L 8PS1301-3HF2 6 units.960 3 L3 N2 L3 L2 N L1 2 x 6 0. X CD-L-224-3-0,-L 8PS1302-3HF2 6 units.960 2 L1 L2 N2 N L3 L3 2 x 2 1 X CD-L-224-2-1-L 8PS1300-2HF2 6 units 3.970 1. PE 2 x 2 1 X CD-L-224-1,-1-L 8PS1300-1HF2 6 units 2.980 3 2 7 2 x 2 1. X CD-L-226-3-1,-L 8PS1300-3JF2 6 units 6.20 3 conductors 1) 2 x 3 1 X CD-L-226-3-1-L 8PS1301-3JF2 6 units 6.20 3 PE L3 L4 L3 L N 2 x 6 0. X CD-L-226-3-0,-L 8PS1302-3JF2 6 units 6.20 2 N2 L2 L1 L1 L2 N2 2 x 2 1 X CD-L-226-2-1-L 8PS1300-2JF2 6 units 4.170 1. N L3 L3 2 x 2 1 X CD-L-226-1,-1-L 8PS1300-1JF2 6 units 3.130 G_NSV0_014 G_NSV0_01 L L4 PE 1) L4/L circuit: max. rated current 2 A. 3/16 Siemens LV 70 2009 * You can order this quantity or a multiple thereof.
CD-L System 2... 40 A Trunking units Version Length Conductor configuration Tap-off points DT Type Order No. PS* Weight Number Spacing per unit approx. m m kg Rated current I e = 40 A, tap-off points on one side Trunking units 3 3 conductors 2 1. X CD-L-1402-3-1,-L 8PS1300-3BF40 6 units 2.960 Sheet-steel enclosure, 3 PE 3 1 X CD-L-1402-3-1-L 8PS1301-3BF40 6 units 2.960 painted, white (RAL 9016), L3 uncoded tap-off points 3 6 0. X CD-L-1402-3-0,-L 8PS1302-3BF40 6 units 2.960 2 N 2 1 X CD-L-1402-2-1-L 8PS1300-2BF40 6 units 1.970 1. 2 1 X CD-L-1402-1,-1-L 8PS1300-1BF40 6 units 1.480 3 conductors 2 1. X CD-L-1404-3-1,-L 8PS1300-3CF40 6 units 3.330 3 PE 3 1 X CD-L-1404-3-1-L 8PS1301-3CF40 6 units 3.330 L3 L3 3 L2 N2 6 0. X CD-L-1404-3-0,-L 8PS1302-3CF40 6 units 3.330 L1 2 N 2 1 X CD-L-1404-2-1-L 8PS1300-2CF40 6 units 2.220 1. 2 1 X CD-L-1404-1,-1-L 8PS1300-1CF40 6 units 1.660 G_NSV0_016 3 7 conductors 1) 2 1. X CD-L-1406-3-1,-L 8PS1300-3DF40 6 units 3.480 3 PE 3 1 X CD-L-1406-3-1-L 8PS1301-3DF40 6 units 3.480 L4 L3 L3 3 L2 N2 6 0. X CD-L-1406-3-0,-L 8PS1302-3DF40 6 units 3.480 L1 2 N 2 1 X CD-L-1406-2-1-L 8PS1300-2DF40 6 units 2.320 L 1. 2 1 X CD-L-1406-1,-1-L 8PS1300-1DF40 6 units 1.740 Rated current I e = 2 40 A, tap-off points on two sides Trunking units 3 2 3 conductors 2 x 2 1. X CD-L-2402-3-1,-L 8PS1300-3FF40 6 units.920 Sheet-steel enclosure, 3 PE 2 x 3 1 X CD-L-2402-3-1-L 8PS1301-3FF40 6 units.920 painted, white (RAL 9016), L3 N uncoded tap-off points 3 2 x 6 0. X CD-L-2402-3-0,-L 8PS1302-3FF40 6 units.920 2 N L3 2 x 2 1 X CD-L-2402-2-1-L 8PS1300-2FF40 6 units 3.940 PE 1. 2 x 2 1 X CD-L-2402-1,-1-L 8PS1300-1FF40 6 units 2.960 3 1 conductors 2 x 2 1. X CD-L-2404/2-KR-3-1,-L 8PS1303-3GF40 6 units 6.290 3 1 3 conductors 2 x 3 1 X CD-L-2404/2-KR-3-1-L 8PS1304-3GF40 6 units 6.290 PE 3 2 x 6 0. X CD-L-2404/2-KR-3-0,-L 8PS130-3GF40 6 units 6.290 L3 L3 N N2 2 L2 2 x 2 1 X CD-L-2404/2-KR-2-1-L 8PS1303-2GF40 6 units 4.190 L1 N L3 1. 2 x 2 1 X CD-L-2404/2-KR-1,-1-L 8PS1303-1GF40 6 units 3.140 G_NSV0_017 G_NSV0_0149 G_NSV0_010 G_NSV0_011 G_NSV0_012 G_NSV0_013 PE 3 2 conductors 2 x 2 1. X CD-L-2404-3-1,-L 8PS1300-3HF40 6 units 6.60 3 PE 2 x 3 1 X CD-L-2404-3-1-L 8PS1301-3HF40 6 units 6.60 3 L3 N2 L3 L2 N L1 2 x 6 0. X CD-L-2404-3-0,-L 8PS1302-3HF40 6 units 6.60 2 L1 L2 N2 N L3 L3 2 x 2 1 X CD-L-2404-2-1-L 8PS1300-2HF40 6 units 4.440 1. PE 2 x 2 1 X CD-L-2404-1,-1-L 8PS1300-1HF40 6 units 3.330 3 2 7 2 x 2 1. X CD-L-2406-3-1,-L 8PS1300-3JF40 6 units 6.90 3 conductors 1) 2 x 3 1 X CD-L-2406-3-1-L 8PS1301-3JF40 6 units 6.90 3 PE L3 L4 L3 L N 2 x 6 0. X CD-L-2406-3-0,-L 8PS1302-3JF40 6 units 6.90 2 N2 L2 L1 L1 L2 N2 2 x 2 1 X CD-L-2406-2-1-L 8PS1300-2JF40 6 units 4.630 1. N L3 L3 2 x 2 1 X CD-L-2406-1,-1-L 8PS1300-1JF40 6 units 3.470 G_NSV0_014 G_NSV0_01 L L4 PE 3 1) L4/L circuit: max. rated current 2 A. * You can order this quantity or a multiple thereof. Siemens LV 70 2009 3/17
CD-L System 2... 40 A Feeder units Overview The feeder units are installed at the beginning of a busbar line. They are available as entry and end feeder units and are connected with the corresponding end of the straight element (the entry feeder unit without connecting flange, the end feeder unit with connecting flange). The two circuits are mechanically separated on two-sided busbar elements. Enclosure material Connection boxes: thermoplast Connection point: galvanized metal enclosure Connection cross-sections of terminals N/L1/L2/L3: max. cable cross-section 10 mm 2 L4/L: max. cable cross-section 2. mm 2 PU: max. cable cross-section 6 mm 2 Selection and ordering data Unpainted feeder units (supplied from stock) 3 Version Length Conductor configuration DT Type Order No. PS* Weight per unit approx. m kg Rated current I e = 2 A, one-sided Entry feeder units, unpainted 0.23 3 conductors X CD-L-124-EA 8PS0330-0CF2 1 unit 0.32 (coded KR, KW) L3, N conductors L3, L2, L1, N 0.23 7 conductors 1) X CD-L-126-EA 8PS0330-0DF2 1 unit 0.37 G_NSV0_0167 L4, L3, L2, L1, N, L End feeder units, unpainted (coded KR, KW) G_NSV0_0169 0.32 3 conductors X CD-L-124-EE 8PS0332-0CF2 1 unit 0.20 L3, N conductors L3, L2, L1, N 0.32 7 conductors 1) X CD-L-126-EE 8PS0332-0DF2 1 unit 0.620 L4, L3, L2, L1, N, L Rated current I e = 2 2 A, two-sided Entry feeder units, unpainted (coded KR, KW) G_NSV0_0168 End feeder units, unpainted (coded KR, KW) G_NSV0_0170 0.23 2 3 conductors X CD-L-224-EA 8PS0331-0HF2 1 unit 0.60 2 L3, N 1 conductors / 1 3 conductors 1 L3, L2, L1, N / 1 L3, N 2 conductors 2 L3, L2, L1, N 0.23 2 7 conductors 1) X CD-L-226-EA 8PS0331-0JF2 1 unit 0.70 2 L4, L3, L2, L1, N, L 0.32 2 3 conductors X CD-L-224-EE 8PS0333-0HF2 1 unit 1.040 2 L3, N 1 conductors / 1 3 conductors 1 L3, L2, L1, N / 1 L3, N 2 conductors 2 L3, L2, L1, N 0.32 2 7 conductors 1) X CD-L-226-EE 8PS0333-0JF2 1 unit 1.240 2 L4, L3, L2, L1, N, L 1) L4/L circuit: max. rated current 2 A. 3/18 Siemens LV 70 2009 * You can order this quantity or a multiple thereof.
CD-L System 2... 40 A Feeder units Version Length Conductor configuration DT Type Order No. PS* Weight per unit approx. m kg Rated current I e = 40 A, one-sided Entry feeder units, unpainted 0.23 3 conductors X CD-L-1404-EA 8PS0330-0CF40 1 unit 0.328 (coded KR, KW) L3, N conductors L3, L2, L1, N 0.23 7 conductors 1) X CD-L-1406-EA 8PS0330-0DF40 1 unit 0.378 G_NSV0_0167 L4, L3, L2, L1, N, L End feeder units, unpainted (coded KR, KW) G_NSV0_0169 0.32 3 conductors X CD-L-1404-EE 8PS0332-0CF40 1 unit 0.0 L3, N conductors L3, L2, L1, N 0.32 7 conductors 1) X CD-L-1406-EE 8PS0332-0DF40 1 unit 0.60 L4, L3, L2, L1, N, L Rated current I e = 2 40 A, two-sided Entry feeder units, unpainted (coded KR, KW) G_NSV0_0168 End feeder units, unpainted (coded KR, KW) G_NSV0_0170 0.23 2 3 conductors X CD-L-2404-EA 8PS0331-0HF40 1 unit 0.680 2 L3, N 1 conductors / 1 3 conductors 1 L3, L2, L1, N / 1 L3, N 2 conductors 2 L3, L2, L1, N 0.23 2 7 conductors 1) X CD-L-2406-EA 8PS0331-0JF40 1 unit 0.780 2 L4, L3, L2, L1, N, L 0.32 2 3 conductors X CD-L-2404-EE 8PS0333-0HF40 1 unit 1.100 2 L3, N 1 conductors / 1 3 conductors 1 L3, L2, L1, N / 1 L3, N 2 conductors 2 L3, L2, L1, N 0.32 2 7 conductors 1) X CD-L-2406-EE 8PS0333-0JF40 1 unit 1.300 2 L4, L3, L2, L1, N, L 3 1) L4/L circuit: max. rated current 2 A. * You can order this quantity or a multiple thereof. Siemens LV 70 2009 3/19
CD-L System 2... 40 A Feeder units Painted feeder units (delivery on request) Version Length Conductor configuration DT Type Order No. PS* Weight per unit approx. m kg Rated current I e = 2 A, one-sided Entry feeder unit, painted, white (RAL 9016) 0.23 3 conductors X CD-L-124-EA-L 8PS1330-0CF2 1 unit 0.32 L3, N conductors L3, L2, L1, N G_NSV0_0171 0.23 7 conductors 1) X CD-L-126-EA-L 8PS1330-0DF2 1 unit 0.37 L4, L3, L2, L1, N, L End feeder unit, painted, white (RAL 9016) 0.32 3 conductors X CD-L-124-EE-L 8PS1332-0CF2 1 unit 0.20 L3, N conductors L3, L2, L1, N 0.32 7 conductors 1) X CD-L-126-EE-L 8PS1332-0DF2 1 unit 0.620 G_NSV0_0172 L4, L3, L2, L1, N, L 3 Rated current I e = 2 2 A, two-sided Entry feeder unit, painted, white (RAL 9016) 0.23 2 3 conductors X CD-L-224-EA-L 8PS1331-0HF2 1 unit 0.60 G_NSV0_0173 2 L3, N 1 conductors / 1 3 conductors 1 L3, L2, L1, N / 1 L3, N 2 conductors 2 L3, L2, L1, N 0.23 2 7 conductors 1) X CD-L-226-EA-L 8PS1331-0JF2 1 unit 0.70 2 L4, L3, L2, L1, N, L End feeder unit, painted, white (RAL 9016) 0.32 2 3 conductors X CD-L-224-EE-L 8PS1333-0HF2 1 unit 1.040 G_NSV0_0174 2 L3, N 1 conductors / 1 3 conductors 1 L3, L2, L1, N / 1 L3, N 2 conductors 2 L3, L2, L1, N 0.32 2 7 conductors 1) X CD-L-226-EE-L 8PS1333-0JF2 1 unit 1.240 2 L4, L3, L2, L1, N, L 1) L4/L circuit: max. rated current 2 A. 3/20 Siemens LV 70 2009 * You can order this quantity or a multiple thereof.
CD-L System 2... 40 A Feeder units Version Length Conductor configuration DT Type Order No. PS* Weight per unit approx. m kg Rated current I e = 40 A, one-sided Entry feeder unit, painted, white (RAL 9016) 0.23 3 conductors X CD-L-1404-EA-L 8PS1330-0CF40 1 unit 0.328 L3, N conductors L3, L2, L1, N G_NSV0_0171 0.23 7 conductors 1) X CD-L-1406-EA-L 8PS1330-0DF40 1 unit 0.378 L4, L3, L2, L1, N, L End feeder unit, painted, white (RAL 9016) 0.32 3 conductors X CD-L-1404-EE-L 8PS1332-0CF40 1 unit 0.0 L3, N conductors L3, L2, L1, N 0.32 7 conductors 1) X CD-L-1406-EE-L 8PS1332-0DF40 1 unit 0.60 G_NSV0_0172 L4, L3, L2, L1, N, L Rated current I e = 2 40 A, two-sided Entry feeder unit, painted, white (RAL 9016) 0.23 2 3 conductors X CD-L-2404-EA-L 8PS1331-0HF40 1 unit 0.680 G_NSV0_0173 2 L3, N 1 conductors / 1 3 conductors 1 L3, L2, L1, N / 1 L3, N 2 conductors 2 L3, L2, L1, N 0.23 2 7 conductors 1) X CD-L-2406-EA-L 8PS1331-0JF40 1 unit 0.780 2 L4, L3, L2, L1, N, L End feeder unit, painted, white (RAL 9016) 0.32 2 3 conductors X CD-L-2404-EE-L 8PS1333-0HF40 1 unit 1.100 G_NSV0_0174 2 L3, N 1 conductors / 1 3 conductors 1 L3, L2, L1, N / 1 L3, N 2 conductors 2 L3, L2, L1, N 0.32 2 7 conductors 1) X CD-L-2406-EE-L 8PS1333-0JF40 1 unit 1.300 2 L4, L3, L2, L1, N, L 3 1) L4/L circuit: max. rated current 2 A. * You can order this quantity or a multiple thereof. Siemens LV 70 2009 3/21
CD-L System 2... 40 A End flanges Overview The end flanges serve as touch protection at the end of the busbar trunking line. They are available in two versions (end caps as mating piece for entry feeder unit and end caps with connecting piece as mating piece for end feeder unit). They are connected with the corresponding end of the straight element. Enclosure material End cover: thermoplast Connecting piece (EE-EF only): galvanized metal enclosure Selection and ordering data Unpainted end flanges (supplied from stock) 3 Version Length Conductor configuration DT Type Order No. PS* Weight per unit approx. m kg Rated current I e = 2 and 40 A, one-sided End flanges 0.02 3 conductors X CD-L-1406-EA-EF 8PS1337-0DF40 1 unit 0.030 (coded KR, KW), L3, N can be used with entry feeder unit conductors L3, L2, L1, N 7 conductors G_NSV0_0176 L4, L3, L2, L1, N, L End flanges, unpainted (coded KR, KW), can be used with end feeder unit G_NSV0_017 0.1 3 conductors X CD-L-1406-EE-EF 8PS033-0DF40 1 unit 0.200 L3, N conductors L3, L2, L1, N 7 conductors L4, L3, L2, L1, N, L Rated current I e = 2 2 and 2 40 A, two-sided End flanges 0.02 2 3 conductors X CD-L-2406-EA-EF 8PS1338-0JF40 1 unit 0.040 (coded KR, KW), 2 L3, N can be used with entry feeder unit 1 conductors / 1 3 conductors 1 L3, L2, L1, N / 1 L3, N G_NSV0_0178 2 conductors 2 L3, L2, L1, N 2 7 conductors 2 L4, L3, L2, L1, N, L End flanges, unpainted 0.1 2 3 conductors X CD-L-2406-EE-EF 8PS0336-0JF40 1 unit 0.370 (coded KR, KW), 2 L3, N can be used with end feeder unit 1 conductors / 1 3 conductors 1 L3, L2, L1, N / 1 L3, N 2 conductors G_NSV0_0177 2 L3, L2, L1, N 2 7 conductors 2 L4, L3, L2, L1, N, L 3/22 Siemens LV 70 2009 * You can order this quantity or a multiple thereof.
CD-L System 2... 40 A End flanges Painted end flanges (delivery on request) Version Length Conductor configuration DT Type Order No. PS* Weight per unit approx. m kg Rated current I e = 2 and 40 A, one-sided End flanges, 0.02 3 conductors X CD-L-1406-EA-EF 8PS1337-0DF40 1 unit 0.030 can be used with entry feeder unit G_NSV0_0176 L3, N conductors L3, L2, L1, N 7 conductors L4, L3, L2, L1, N, L End flanges, painted, white (RAL 9016) 0.1 3 conductors X CD-L-1406-EE-EF-L 8PS133-0DF40 1 unit 0.200 can be used with end feeder unit G_NSV0_0179 L3, N conductors L3, L2, L1, N 7 conductors L4, L3, L2, L1, N, L Rated current I e = 2 2 and 2 40 A, two-sided End flanges, 0.02 2 3 conductors X CD-L-2406-EA-EF 8PS1338-0JF40 1 unit 0.040 can be used with entry feeder unit G_NSV0_0178 2 L3, N 1 conductors / 1 3 conductors 1 L3, L2, L1, N / 1 L3, N 2 conductors 2 L3, L2, L1, N 2 7 conductors 2 L4, L3, L2, L1, N, L End flanges, painted, white (RAL 9016) 0.1 2 3 conductors X CD-L-2406-EE-EF-L 8PS1336-0JF40 1 unit 0.370 can be used with end feeder unit G_NSV0_0180 2 L3, N 1 conductors / 1 3 conductors 1 L3, L2, L1, N / 1 L3, N 2 conductors 2 L3, L2, L1, N 2 7 conductors 2 L4, L3, L2, L1, N, L 3 * You can order this quantity or a multiple thereof. Siemens LV 70 2009 3/23
CD-L System 2... 40 A Junction units Overview The enclosure is made of thermoplast and the connection point comprises a galvanized metal enclosure. For flexible junction units, double-sided, the two circuits are mechanically separated. Selection and ordering data Unpainted junction units (supplied from stock) Version Length Conductor configuration DT Type Order No. PS* Weight per unit approx. m kg Rated current I e = 2 A, one-sided Flexible junction units, unpainted 0.7 3 conductors X CD-L-124-R 8PS0320-0CF2 1 unit 1.170 (coded KR, KW) L3, N conductors L3, L2, L1, N 0.7 7 conductors 1) X CD-L-126-R 8PS0320-0DF2 1 unit 1.270 L4, L3, L2, L1, N, L 3 G_NSV0_0198 Rated current I e = 2 2 A, two-sided Flexible junction units, unpainted (coded KR, KW) G_NSV0_0199 Rated current I e = 40 A, one-sided Flexible junction units, unpainted (coded KR, KW) 0.7 2 3 conductors X CD-L-224-R 8PS0321-0HF2 1 unit 2.340 2 L3, N 1 conductors / 1 3 conductors 1 L3, L2, L1, N / 1 L3, N 2 conductors 2 L3, L2, L1, N 0.7 2 7 conductors 1) X CD-L-226-R 8PS0321-0JF2 1 unit 2.40 2 L4, L3, L2, L1, N, L 0.7 3 conductors X CD-L-1404-R 8PS0320-0CF40 1 unit 1.180 L3, N conductors L3, L2, L1, N 0.7 7 conductors 1) X CD-L-1406-R 8PS0320-0DF40 1 unit 1.280 L4, L3, L2, L1, N, L G_NSV0_0198 Rated current I e = 2 40 A, two-sided Flexible junction units, unpainted (coded KR, KW) G_NSV0_0199 0.7 2 3 conductors X CD-L-2404-R 8PS0321-0HF40 1 unit 2.360 2 L3, N 1 conductors / 1 3 conductors 1 L3, L2, L1, N / 1 L3, N 2 conductors 2 L3, L2, L1, N 0.7 2 7 conductors 1) X CD-L-2406-R 8PS0321-0JF40 1 unit 2.60 2 L4, L3, L2, L1, N, L 1) L4/L circuit: max. rated current 2 A. 3/24 Siemens LV 70 2009 * You can order this quantity or a multiple thereof.
CD-L System 2... 40 A Junction units Painted junction units (delivery on request) Version Length Conductor configuration DT Type Order No. PS* Weight per unit approx. m kg Rated current I e = 2 A, one-sided Flexible junction units, 0.7 3 conductors X CD-L-124-R-L 8PS1320-0CF2 1 unit 1.170 painted, white (RAL 9016) L3, N conductors L3, L2, L1, N 0.7 7 conductors 1) X CD-L-126-R-L 8PS1320-0DF2 1 unit 1.270 L4, L3, L2, L1, N, L G_NSV0_0181 Rated current I e = 2 2 A, two-sided Flexible junction units, painted, white (RAL 9016) G_NSV0_0182 Rated current I e = 40 A, two-sided Flexible junction units, painted, white (RAL 9016) 0.7 2 3 conductors X CD-L-224-R-L 8PS1321-0HF2 1 unit 2.340 2 L3, N 1 conductors / 1 3 conductors 1 L3, L2, L1, N / 1 L3, N 2 conductors 2 L3, L2, L1, N 0.7 2 7 conductors 1) X CD-L-226-R-L 8PS1321-0JF2 1 unit 2.40 2 L4, L3, L2, L1, N, L 0.7 3 conductors X CD-L-1404-R-L 8PS1320-0CF40 1 unit 1.180 L3, N conductors L3, L2, L1, N 0.7 7 conductors 1) X CD-L-1406-R-L 8PS1320-0DF40 1 unit 1.280 L4, L3, L2, L1, N, L 3 G_NSV0_0181 Rated current I e = 2 40 A, two-sided Flexible junction units, painted, white (RAL 9016) G_NSV0_0182 0.7 2 3 conductors X CD-L-2404-R-L 8PS1321-0HF40 1 unit 2.360 2 L3, N 1 conductors / 1 3 conductors 1 L3, L2, L1, N / 1 L3, N 2 conductors 2 L3, L2, L1, N 0.7 2 7 conductors 1) X CD-L-2406-R-L 8PS1321-0JF40 1 unit 2.60 2 L4, L3, L2, L1, N, L 1) L4/L circuit: max. rated current 2 A. * You can order this quantity or a multiple thereof. Siemens LV 70 2009 3/2
CD-L System 2... 40 A Tap-off plugs Selection and ordering data Uncoded tap-off plugs (supplied from stock) Version Color 1) Tap-off plugs with cable FROR cable according to IEC 6074-1 and flame-retardant according to IEC 60332-1 3-pole, phase L1, L2 or L3, with N and PE; without fuse G_NSV0_0183 -pole, L1 or L2, L3, N and PE; without fuses Top part/ Base OR/GR (N/L1) OR/GN (N/L2) OR/BK (N/L3) OR/BN (N2/L3) Outgoing cable Rated DT Type Order No. PS* Weight Length Crosssection current I e per unit approx. m mm 2 A kg 1 3 1 10 X CD-L-A3O10- N/L1-1 1 3 1 10 X CD-L-A3O10- N/L2-1 1 3 1 10 X CD-L-A3O10- N/L3-1 1 3 1 10 X CD-L-A3O10- N2/L3-1 OR/OR 2 1 10 X CD-L-AO10- N/L1/L2/L3-2 8PS0044-1KF10 units 0.10 8PS0044-1LF10 units 0.10 8PS0044-1MF10 units 0.10 8PS0044-1NF10 units 0.10 8PS0044-2QF10 units 0.320 3 G_NSV0_0184 3-pole + L4/L, phase L1, L2 or L3, with N and PE; without fuses G_NSV0_018 L4/L for 7-conductor busbar system (standard and codable tap-off points), without fuses BK/GR N/L1 + L4/L BK/GN N/L2 + L4/L BK/BK N/L3 + L4/L 2 1 10 X CD-L-AO10- N/L1/L4/L-2 2 1 10 X CD-L-AO10- N/L2/L4/L-2 2 1 10 X CD-L-AO10- N/L3/L4/L-2 OR/OR 1 3 1 10 X CD-L-A3O10- L4/L-1 8PS0044-2RF10 units 0.320 8PS0044-2SF10 units 0.320 8PS0044-2TF10 units 0.320 8PS0044-1UF10 units 0.10 G_NSV0_0186 1) OR = orange GR = gray GN = green BK = black BN = brown 3/26 Siemens LV 70 2009 * You can order this quantity or a multiple thereof.
CD-L System 2... 40 A Tap-off plugs Version Tap-off plugs with terminals L/N/PE connection: max. cable diameter 14 mm, max. conductor cross-section 2. mm 2 Color Top part/base Rated current I e DT Type Order No. PS* Weight per unit approx. A kg G_NSV0_0187 3-pole, phase can be changed to L1, L2 or L3, with N and PE; without fuse TR/GR 16 X CD-L-A3O16- N/L-0 8PS0040-0AF16 units 0.130 3-pole + L4/L, phase can be changed to L1, L2 or L3, with N and PE; without fuse TR/GR 16 X CD-L-AO16- N/L/L4/L-0 8PS0041-0AF16 units 0.10 3-pole, phase can be changed to L1, L2 or L3, with N and PE; with micro-fuse 6.3 A, size mm 20 mm, type gg (IEC), gl (VDE) quick TR/GR 6.3 X CD-L-A3M6,3- N/L-0 8PS0042-0AF10 units 0.140 3 3-pole, phase can be changed to L1, L2 or L3, with N and PE; with cylindrical fuse 16 A, size 8. mm 31. mm, type gg (IEC), gl (VDE) quick TR/GR 16 X CD-L-A3M16- N/L-0 8PS0042-0AF16 units 0.10 3-pole + L4/L, phase can be changed to L1, L2 or L3, with N and PE; with micro-fuse 6.3 A, size mm 20 mm, type gg (IEC), gl (VDE) quick TR/GR 6.3 X CD-L-AM6,3- N/L/L4/L-0 8PS0043-0AF10 units 0.170 3-pole + L4/L, phase can be changed to L1, L2 or L3, with N and PE; with cylindrical fuse 16 A, size 8. mm 31. mm, type gg (IEC), gl (VDE) quick TR/GR 16 X CD-L-AM16- N/L/L4/L-0 8PS0043-0AF16 units 0.190 Mobile contacts Mobile contacts G_NSV0_01623 N 16 A without fuse BU 16 X CD-L-AMCO16-N 8PS0081-0AA16 units 0.010 P 16 A without fuse BK 16 X CD-L-AMCO16-P 8PS0082-0AA16 units 0.010 P 10-A holder with micro-fuse 6.3 A, BK 6.3 X CD-L-AMCM6,3-P 8PS0083-0AA10 units 0.010 size mm 20 mm, type gg (IEC), gl (VDE) quick P 16-A holder with cylindrical fuse 16 A, size 8. mm 31. mm, type gg (IEC), gl (VDE) quick BK 16 X CD-L-AMCM16-P 8PS0084-0AA16 units 0.020 1) TR = transparent GR = gray BU = blue BK = black * You can order this quantity or a multiple thereof. Siemens LV 70 2009 3/27
CD-L System 2... 40 A 3 Tap-off plugs Coded tap-off plugs (delivery on request) Version Color 1) Tap-off plugs with cable FROR cable according to IEC 6074-1 and flame-retardant according to IEC 60332-1 For red coded tap-off points 3-pole, phase L1, L2 or L3, with N and PE; without fuse G_NSV0_0188 For white coded tap-off points 3-pole, phase L1, L2 or L3, with N and PE; without fuse G_NSV0_0189 Top part/ Base RD/GR (N/L1) RD/GN (N/L2) RD/BK (N/L3) RD/BN (N2/L3) WH/GR (N/L1) WH/GN (N/L2) WH/BK (N/L3) WH/BN (N2/L3) Outgoing cable Rated DT Type Order No. PS* Weight Length Crosssection current I e per unit approx. m mm 2 A kg 1 3 1 10 X CD-L-A3O10- N/L1-1-KR 1 3 1 10 X CD-L-A3O10- N/L2-1-KR 1 3 1 10 X CD-L-A3O10- N/L3-1-KR 1 3 1 10 X CD-L-A3O10- N2/L3-1-KR 1 3 1 10 X CD-L-A3O10- N/L1-1-KW 1 3 1 10 X CD-L-A3O10- N/L2-1-KW 1 3 1 10 X CD-L-A3O10- N/L3-1-KW 1 3 1 10 X CD-L-A3O10- N2/L3-1-KW 8PS004-1KF10 units 0.210 8PS004-1LF10 units 0.210 8PS004-1MF10 units 0.210 8PS004-1NF10 units 0.210 8PS0064-1KF10 units 0.210 8PS0064-1LF10 units 0.210 8PS0064-1MF10 units 0.210 8PS0064-1NF10 units 0.210 1) RD = red GR = gray GN = green BK = black BN = brown WH = white 3/28 Siemens LV 70 2009 * You can order this quantity or a multiple thereof.
CD-L System 2... 40 A Tap-off plugs Version Tap-off plugs with terminals L/N/PE connection: max. cable diameter 14 mm, max. conductor cross-section 2. mm 2 For red coded tap-off points Color Top part/ Base Rated current I e DT Type Order No. PS* Weight per unit approx. A kg G_NSV0_0190 3-pole, phase can be changed to L1, L2 or L3, with N and PE; without fuse TR/RD 16 X CD-L-A3O16- N/L-KR-0 8PS000-0AF16 units 0.130 3-pole + L4/L, phase can be changed to L1, L2 or L3, with N and PE; without fuse TR/RD 16 X CD-L-AO16- N/L/L4/L-KR-0 8PS001-0AF16 units 0.10 3-pole, phase can be changed to L1, L2 or L3, with N and PE; with cylindrical fuse 16 A, size 8. mm 31. mm, type gg (IEC), gl (VDE) quick TR/RD 16 X CD-L-A3M16- N/L-KR-0 8PS002-0AF16 units 0.10 3 3-pole + L4/L, phase can be changed to L1, L2 or L3, with N and PE; with cylindrical fuse 16 A, size 8. mm 31. mm, type gg (IEC), gl (VDE) quick TR/RD 16 X CD-L-AM16- N/L/L4/L-KR-0 8PS003-0AF16 units 0.190 For white coded tap-off points G_NSV0_01624 3-pole, phase can be changed to L1, L2 or L3, with N and PE; without fuse TR/WH 16 X CD-L-A3O16- N/L-KW-0 8PS006-0AF16 units 0.130 3-pole + L4/L, phase can be changed to L1, L2 or L3, with N and PE; without fuse TR/WH 16 X CD-L-AO16- N/L/L4/L-KW-0 8PS0067-0AF16 units 0.10 3-pole, phase can be changed to L1, L2 or L3, with N and PE; with cylindrical fuse 16 A, size 8. mm 31. mm, type gg (IEC), gl (VDE) quick TR/WH 16 X CD-L-A3M16- N/L-KW-0 8PS0066-0AF16 units 0.10 3-pole + L4/L, phase can be changed to L1, L2 or L3, with N and PE; with cylindrical fuse 16 A, size 8. mm 31. mm, type gg (IEC), gl (VDE) quick TR/WH 16 X CD-L-AM16- N/L/L4/L-KW-0 8PS0068-0AF16 units 0.190 1) TR = transparent RD = red WH = white * You can order this quantity or a multiple thereof. Siemens LV 70 2009 3/29
CD-L System 2... 40 A Accessories Selection and ordering data Version Fixing Standard fixing brackets for trunking unit or luminaire fixing For mounting trunking units on the ceiling or floor and for suspending luminaires on the trunking unit Number of sides Load capacity DT Type Order No. PS* Weight per unit approx. kg kg 1 12 X CD-L-B1-G-12 8PS0070-0AA00 12 units 0.030 2 12 X CD-L-B2-G-12 8PS0073-0AA00 12 units 0.040 G_NSV0_0191 Universal suspension brackets for mounting trunking units and luminaires For suspending trunking units on the wall, on the ceiling or on the floor and for suspending luminaires on the trunking unit 1 2 X CD-L-B1-O-2 8PS0072-0AA00 12 units 0.00 2 2 X CD-L-B2-O-2 8PS007-0AA00 12 units 0.060 3 G_NSV0_0192 Fixing brackets with hook for mounting trunking units or luminaires For suspension by cable or pendant or chain and for suspending the luminaires on the trunking unit 1 2 X CD-L-BH1-2 8PS008-0AA00 12 units 0.030 2 2 X CD-L-BH2-2 8PS0086-0AA00 12 units 0.040 G_NSV0_0193 Hooks, open/closed, for mounting trunking units or luminaires For suspension by cable or pendant or chain in conjunction with CD-B suspension/fixing bracket G_NSV0_0194 Hook open 1 2 X CD-L-HO 8PS0076-0AA00 12 units 0.010 Hook closed 2 2 X CD-L-HG 8PS0077-0AA00 12 units 0.010 3/30 Siemens LV 70 2009 * You can order this quantity or a multiple thereof.
CD-L System 2... 40 A Accessories Version DT Type Order No. PS* Weight per unit approx. kg Cable ducts Cable ducts made of plastic (white), standard length 3 m. X CD-L-CC 8PS0087-0AA00 6 units 0.02 G_NSV0_019 Cable duct used for cables in auxiliary circuits. It is mounted on the trunking unit with the fixing brackets for cable ducts (two brackets every 3 m). Fixing brackets for cable duct for mounting the cable ducts on the ceiling, on the floor or on the wall, alone or in combination with trunking units X CD-L-BCCO 8PS0088-0AA00 12 units 0.040 G_NSV0_0196 It can be mounted on the standard fixing brackets or universal suspension brackets. Optional equipment for degree of protection IP IP covers for tap-off point X CD-L-FAS 8PS0080-0AA00 12 units 0.010 3 G_NSV0_0197 * You can order this quantity or a multiple thereof. Siemens LV 70 2009 3/31
CD-L System 2... 40 A Configuration information Overview Specimen text for tenders Item Quantity Description Unit price Amount 3... m Busbar trunking system for small loads and lighting installations As type-tested low-voltage switchgear and controlgear combination (TTA) according to IEC/EN 60439-1 and -2 Rated current... A, corresponds to thermal rated current... A at max. +40 C and +3 C on a 24 h average for indoor installation Rated insulation voltage U i = 690 V AC; overvoltage category/degree of pollution III/3 Operational voltage... V,... Hz Rated peak withstand current of busbar trunking system,... ka tested according to IEC/EN 60439-1 Degree of protection IP 3-, -, 7-, 2 3, 1 - + 1 3-, 2, 2 7-conductor system Copper conductor, insulated along its whole length Trunking units, sheet-steel enclosed, unpainted/painted finish Halogen-free Tap-off points at 0. m, 1 m or 1. m intervals per side Supplied ready for connection with all assembly parts Made by Siemens Type CD-L-... Comprising: 3/32 Siemens LV 70 2009
f CD-L System 2... 40 A Configuration information Design Determining the fixing intervals The closed section of the CD-L system has a high degree of mechanical strength. The load diagrams show the maximum permissible loading in relation to the fixing interval (distance between suspension points). Deflection f of the busbar trunking unit should not be greater than 1/30 of the distance (L) between fixing points. F = balanced load. Load and deflection as a function of spacing L F L Balanced load L NSV0_00018 Concentrated load Max. load P 40 3 30 2 20 1 (kg) 0 2,0 f/l = 1/30 2, (m) 3,0 Fixing interval L NSV0_01637 Max. deflection f 16 14 12 10 f = 1 L 30 8 6 4 (mm) 0 2,0 2, (m) 3,0 Fixing interval L NSV0_01638 3 Load characteristic (trunking unit with concentrated load) Mounting examples Deflection characteristic (trunking unit with concentrated load) 3 m 3 m G_NSV0_01634 G_NSV0_01633 Suspension with standard fixing brackets Suspension with standard fixing brackets Mounting with cable duct and standard fixing brackets Mounting with fixing bracket with hook Siemens LV 70 2009 3/33
CD-L System 2... 40 A Configuration information Arrangement of luminaires The numbers, e.g. $, indicate the corresponding position of the luminaires in the table below. Single lamp Three lamps L1 L2 L3 N L1 L2 L3 N X X X X X NSV0_0002 X X X X NSV0_00030 $ = Single lamp, non-compensated, p.f. = 0. * = Three lamps, alternately series-compensated L1 L3 L2 N L1 L2 L3 N 3 X X X NSV0_00026 X X X NSV0_00031 % = Single lamp, parallel-compensated, p.f. = 0.9 + = Three lamps, non-compensated L1 L2 L3 N X X X X X X NSV0_00027 & = Single lamp, alternately series-compensated, p.f. = 0.1 Two lamps L1 L2 L3 N X X X X X X NSV0_00028 ( = Two lamps, non-compensated L1 L3 L2 N X X X X X X NSV0_00029 ) = Two lamps, duo circuit, p.f. = 1 3/34 Siemens LV 70 2009
CD-L System 2... 40 A Configuration information Connectable luminaires without consideration of voltage drop Lamp voltage per luminaire (linear fluorescent lamp) Arrangement of luminaires Rated current with reactor Length of light fixture Connectable luminaires with protection by miniature circuit breaker At 16 A At 20 A At 2 A At 32 A Units/ phase Total length for connection to 3 phases Units/ phase Total length for connection to 3 phases Units/ phase Total length for connection to 3 phases Units/ phase Total length for connection to 3 phases A m, approx. m, approx. m, approx. m, approx. m, approx. 1 36 W 1 8 W Non-compensated, single-phase $ 0.44 0.70 1.2 1. 33 20 128 96 42 2 163 120 2 32 202 13 66 40 248 186 1 36 W 1 8 W Parallel-compensated, single-phase % 0.2 0.40 1.2 1. 30 19 117 91 37 24 144 11 47 30 183 144 9 37 222 173 1 36 W 1 8 W Alternately compensated, single-phase & 0.23 0.3 1.2 1. 48 32 187 13 60 40 234 192 7 0 292 240 96 64 360 298 3 2 36 W 2 8 W Non-compensated, single-phase ( 0.88 1.40 1.2 1. 16 10 62 48 21 12 81 7 26 16 101 76 41 20 124 93 2 36 W 2 8 W Duo circuit, single-phase ) 0.46 0.71 1.2 1. 24 16 93 76 30 20 117 96 37 2 144 120 47 32 177 149 3 36 W 3 8 W Alternately compensated, three-phase * 0.23 0.3 1.2 1. 48 32 62 1 60 40 78 64 7 0 97 80 96 64 12 103 3 36 W 3 8 W Non-compensated, three-phase + 0.44 0.70 1.2 1. 33 20 42 32 42 2 4 40 2 32 67 1 66 40 86 64 Siemens LV 70 2009 3/3
CD-L System 2... 40 A Configuration information Lamp voltage per luminaire (linear fluorescent lamp) Arrangement of luminaires Rated current with reactor Length of light fixture Connectable luminaires with protection by gl melting fuses At 16 A At 20 A At 2 A At 3 A Units/ phase Total length for connection to 3 phases Units/ phase Total length for connection to 3 phases Units/ phase Total length for connection to 3 phases Units/ phase Total length for connection to 3 phases A m, approx. m, approx. m, approx. m, approx. m, approx. 1 36 W 1 8 W Non-compensated, single-phase $ 0.44 0.70 1.2 1. 33 20 128 96 42 2 163 120 2 32 202 13 72 44 280 211 1 36 W 1 8 W Parallel-compensated, single-phase % 0.2 0.40 1.2 1. 36 23 140 110 44 28 171 134 60 38 234 182 90 6 31 268 3 1 36 W 1 8 W Alternately compensated, single-phase & 0.23 0.3 1.2 1. 48 32 187 13 60 40 234 192 7 0 292 240 10 70 409 336 2 36 W 2 8 W Non-compensated, single-phase ( 0.88 1.40 1.2 1. 16 10 62 48 21 12 81 7 26 16 101 76 36 22 140 10 2 36 W 2 8 W Duo circuit, single-phase ) 0.46 0.71 1.2 1. 24 16 93 76 30 20 117 96 37 2 144 120 1 3 198 168 3 36 W 3 8 W Alternately compensated, three-phase * 0.23 0.3 1.2 1. 48 32 62 1 60 40 78 64 7 0 97 80 10 70 136 112 3 36 W 3 8 W Non-compensated, three-phase + 0.44 0.70 1.2 1. 33 20 42 32 42 2 4 40 2 32 67 1 72 44 93 64 3/36 Siemens LV 70 2009
CD-L System 2... 40 A Configuration information Function Short-circuit protection The lengths of the busbar lines given in the guide value tables (see pages 3/3 and 3/36) take into account only the rated current of the connectable luminaires. To determine the precise length of the busbar line, voltage drops and short-circuit protection must be taken into account. z inc. inc. CD CD z Protective device Incoming cable CD system NSV0_00032 Voltage drop ΔU According to the technical literature, the voltage drop should lie between 3% and % when the load is evenly split in light networks. ΔU(%) = ΔU (V) U e (V) 100 % With ΔU (V) according to page 3/38 Fault protection according to DIN VDE 0100 Part 410 Calculation of the current resulting in automatic interruption, taking into account the incoming supply cable and the outgoing feeder. Luminaire x Tap-off with cable 2 2 1mm or 1,mm Note: DIN VDE 0100 ist equivalent to IEC 60364. 3 I a = U o Z s = U o Z Source + Z Inc + Z CD + Z Out (A) = U o Z Source + Z Inc l Inc + Z CD l CD + Z Out (A) with I a = Current resulting in automatic interruption (A) U o = Voltages to earth (V) Z s = Fault loop impedance. Can be measured, calculated or determined using the network model. Z Source = Source impedance (Ω) l Inc = Single length of supply line (m) l CD = Single length of CD system (m) l Out = Length of outgoing feeder (m) Z Inc = Loop impedance of supply line (Ω/m) Z CD = Loop impedance of CD system (Ω/m) Z Out = Loop impedance of outgoing feeder (Ω/m) For example: Z Inc = 22 10-3 Ω/m at 2. mm 2 Z CD = 4.241 10-3 Ω/m at CD-L 2 A 0.833 10-3 Ω/m at CD-L 40 A Z Out = 4 10-3 Ω/m at 1 mm 2 36 10-3 Ω/m at 1. mm 2 Provided that the protective device is positioned immediately upstream of the busbar line, Z Inc can be ignored. (Ω) The admissible opening delay is as specified in DIN VDE 0100 Part 430: t = with S (11 (s) I a ) 2 t = Admissible opening delay (s) S = Smallest conductor cross-section to be protected (outgoing feeder) 1 mm 2 or 1. mm 2 (mm 2 ) I a = Current according to above calculation (A) The total break time of the selected protective device must not exceed the determined admissible opening delay and must not be greater than s. Siemens LV 70 2009 3/37
CD-L System 2... 40 A Configuration information 3 Short-circuit protection alone A system can be protected against start circuit-alone, by fitting low-voltage LV HRC fuses (gl) into the incoming supply; the fuse size to be appropriate for the prospective short-circuit current at the place of installation. System CD-L-12. CD-L-140. CD-L-22. CD-L-24 Protective device per circuit I cf = 2 ka 1) LV HRC00 2 gl LV HRC00 40 gl LV HRC00 2 gl LV HRC00 40 gl 1) I cf = rated conditional short-circuit current of the busbar trunking system and its outgoing feeders when protected by fuses Overcurrent protective devices for overload and short-circuit protection Due to their high response threshold (1.3 to 1.6 times rated current) and their long rupturing times at small overcurrents, fuses are not suitable for overload protection. For protecting the CD-L busbar trunking system and its outgoing feeders, we recommend miniature circuit breakers or motorprotective circuit breakers. System Protective device per circuit I cc = 1 ka 1) I cc = 20 ka CD-L-12. SY4 32-6 SY8 32-7 CD-L-140. SY4 340-6 SY8 340-7 CD-L-22. SY4 32-6 SY8 32-7 CD-L-24 SY4 340-6 SY8 340-7 1) I cf = rated conditional short-circuit current of the busbar trunking system and its outgoing feeders when protected by circuit breakers Temperature characteristic of CD-L systems Rated current (%) 130 120 110 100 90 80 70 - + +1 +2 +3 +4 + +6 Ambient temperature C (average over 24 h) NSV0_00034 Voltage drop Voltage drop at rated current (Load distribution factor a = 0. for lighting systems) Three-phase current (3 ~), single-phase alternating current (~) U (V/100 m) 18 16 14 12 10 Calculation of the voltage drop For long busbar lines, it may be necessary to calculate the voltage drop. Alternating current: Three-phase current: 8 6 4 2 with ΔU = Voltage drop (V) I = Load current (A) l = Length (m) a = Load distribution factor see Table R = Ohmic resistance R 20 (mω/m) X = Inductive resistance X 20 (mω/m) cos ϕ = Power factor (p. f.) 2 A (~) 2 A (3~) 40 A (~) 40 A (3~) 0,4 0, 0,6 0,7 0,8 0,9 1,0 cos ΔU = a I 2l (R cos ϕ + X sin ϕ) 10 3 ΔU = a 3 I l (R cos ϕ + X sin ϕ) 10 3 Factor a used in the equation for calculating the voltage drop is dependent on the load distribution. NSV0_01639 (V) (V) Load distribution A B Factor a Infeed at A, one outgoing feeder at B 1 A B C D E Infeed at A, outgoing feeders at B, C, D, E 0. A C D E F B Infeed at A, B, outgoing feeders at C, D, E, F 0.2 3/38 Siemens LV 70 2009
CD-L System 2... 40 A Project planning aids Dimensional drawings Trunking units One-side conductor arrangement Cross-section 20 Two side conductor arrangement Cross-section 40 8 G_NSV0_01603 8 G_NSV0_01604 CD-L-122-3-1, CD-L-124-3-1, CD-L-126-3-1, CD-L-122-3-1 CD-L-124-3-1 CD-L-126-3-1 CD-L-122-3-0, CD-L-124-3-0, CD-L-126-3-0, CD-L-222-3-1, CD-L-224-3-1, CD-L-226-3-1, CD-L-224/2-3-1, CD-L-222-3-1 CD-L-224-3-1 CD-L-226-3-1 CD-L-224/2-3-1 CD-L-222-3-0, CD-L-224-3-0, CD-L-226-3-0, CD-L-224/2-3-0, 32 100 3000 3100 3 180 100 1320 180 1000 1000 820 180 00 00 00 00 00 320 G_NSV0_01600 CD-L-122-2-1 CD-L-124-2-1 CD-L-126-2-1 CD-L-222-2-1 CD-L-224-2-1 CD-L-226-2-1 CD-L-224/2-2-1 32 100 2000 2100 180 G_NSV0_01601 1000 820 CD-L-122-1,-1 CD-L-124-1,-1 CD-L-126-1,-1 CD-L-222-1,-1 CD-L-224-1,-1 CD-L-226-1,-1 CD-L-224/2-1,-1 32 100 100 1600 G_NSV0_01602 180 1000 320 Siemens LV 70 2009 3/39
CD-L System 2... 40 A Project planning aids Feeder units and end flanges Entry feeder units One-side conductor arrangement CD-L-124-EA CD-L-126-EA CD-L-1404-EA CD-L-1406-EA Two-side conductor arrangement CD-L-224-EA CD-L-226-EA CD-L-2404-EA CD-L-2406-EA 8 110 120 116 110 120 108 230* G_NSV0_01627 108 230* G_NSV0_01628 3 End feeder units One-side conductor arrangement CD-L-124-EE CD-L-126-EE 8 CD-L-1404-EE CD-L-1406-EE Two-side conductor arrangement CD-L-224-EE CD-L-226-EE CD-L-2404-EE CD-L-2406-EE 110 210 116 110 210 108 220* 100 320 G_NSV0_01629 108 220* 100 320 G_NSV0_01630 End flanges One-side conductor arrangement CD-L-1406-EA-EF Two-side conductor arrangement CD-L-2406-EA-EF 28 66 48 G_NSV0_0160 2 G_NSV0_01606 2 66 End flanges One-side conductor arrangement CD-L-1406-EE-EF Two-side conductor arrangement CD-L-2406-EE-EF 28 1* 48 1* 66 G_NSV0_01631 G_NSV0_01632 66 3/40 Siemens LV 70 2009
CD-L System 2... 40 A Project planning aids Junction units Flexible junction units One-side conductor arrangement CD-L-124-R CD-L-126-R CD-L-1404-R CD-L-1406-R Two-side conductor arrangement CD-L-224-R CD-L-226-R CD-L-2404-R CD-L-2406-R 108 8 230 300 320 108 116 230 300 320 80 80 G_NSV0_01607 G_NSV0_01608 Tap-off plugs 3- or -pole, with cable 2-pole, with cable CD-L-A3O10-N/L-1 CD-L-A3O10-L4/L-1 CD-L-AO10-N/L...-2 N L1 16 18 3 47 18 36 47 18 3 G_NSV0_01611 88 G_NSV0_01612 67 With terminals CD-L-A3O16-N/L-0 CD-L-AO16-N/L...-0 CD-L-A3M6,3-N/L-0 CD-L-AM6,3-N/L...-0 CD-L-A3M16-N/L-0 CD-L-AM16-N/L...-0 Cable max. Ø14 8 9 43 11 16 G_NSV0_01610 Optional equipment IP cover for tap-off point CD-L-FAS 4 42 16 G_NSV0_01609 Siemens LV 70 2009 3/41
CD-L System 2... 40 A Project planning aids Accessories Standard fixing brackets CD-L-B1-G-12 CD-L-B2-G-12 99 14 8 27 99 14 8 27 22 Ø6, 20 42 20 G_NSV0_01617 Ø6, G_NSV0_01618 Universal suspension brackets CD-L-B1-O-2 CD-L-B2-O-2 6,x12 3 7 26, 11,2 36 2, 0 2, 7 6,x12 101 8 17 26 2, 0 101 8 17 18 8, 48 Ø6, 14, 2, 26 18,2 14, 70 G_NSV0_0161 26, Ø6, 8, G_NSV0_01616 36 Fixing brackets with hook CD-L-BH1-2 CD-L-BH2-2 Ø10,8 2, Ø14 2, 10 28 77 18 10 28 77 18 26 6 4, 6 G_NSV0_01613 G_NSV0_01614 3/42 Siemens LV 70 2009
CD-L System 2... 40 A Project planning aids Accessories Hook, open CD-L-HO Hook, closed CD-L-HG M M 63,7 G_NSV0_01619 G_NSV0_01620 1,2 3 3 Fixing bracket for cable duct CD-L-BCCO Cable duct CD-L-CC 8, 6 Ø6, 47 26,4 12 3000 40 2 G_NSV0_01622 3 7 37, 37, hole 6,x12 Ø6, 26,4 9,7 13 7 18 G_NSV0_01621 Siemens LV 70 2009 3/43
CD-L System 2... 40 A Notes 3 3/44 Siemens LV 70 2009
BD01 System 40... 160 A 4 Introduction 4/2 Overview 4/3 Benefits 4/3 Design 4/6 Accessories General data 4/9 Technical specifications Trunking units 4/11 Selection and ordering data Junction units 4/12 Selection and ordering data Feeder units 4/12 Selection and ordering data Tap-off units for international use 4/13 Selection and ordering data Ancillary equipment units for international use 4/19 Selection and ordering data Tap-off units and ancillary equipment units for Belgium 4/21 Selection and ordering data Tap-off units and ancillary equipment units for Denmark 4/22 Selection and ordering data Tap-off units for France 4/23 Selection and ordering data Tap-off units for the United Kingdom 4/24 Selection and ordering data Tap-off units for Switzerland 4/2 Selection and ordering data Accessories 4/27 Selection and ordering data Configuration information 4/29 Overview 4/30 Design 4/32 Function Project planning aids 4/34 Dimensional drawings Siemens LV 70 2009
BD01 System 40... 160 A Introduction Overview 2 1 4 3 NSV0_00041 4 6 4 4 1 Trunking unit 2 Junction unit 3 Feeder unit 4 Tap-off unit Ancillary equipment unit 6 Accessories Version Type-tested low-voltage switchgear and controlgear assembly (TTA) according to IEC/EN 60439-1 IEC/EN 60439-2 Degree of protection High degree of protection IP4 with tap-off points at sides and bottom Degree of protection IP0 with tap-off points at the top Degree of protection increase to IP with optional equipment Components Trunking units -wire system 2 or 3 tap-off points spaced 1 m apart 4 or 6 tap-off points spaced 0. m apart Lengths of 2 m and 3 m Junction units Flexible change of direction Feeder units Universal infeed Tap-off units Up to 63 A With built-in parts or for customized device installation For 3, 4 or 8 modular widths (MW) With or without device installation unit Ancillary equipment units For 4 or 8 modular widths (MW) With or without device installation unit With or without socket assembly Accessories Mounting sets for degree of protection IP Fixing and suspending Coding sets Fire protection kit S90 4/2 Siemens LV 70 2009
BD01 System 40... 160 A Introduction Benefits 7 Flexible power supply 7 Easy and quick planning 7 Time-saving mounting 7 Reliable mechanical and electrical connection 7 High stability, low weight 7 Few basic modules required 7 Storage-friendly system 7 Variable change of the direction of the busbar line 7 Versatile tap-off units 7 Positive opening and closing of tap-off points 7 Optional equipment for increasing the degree of protection to IP for extreme environmental conditions Design Trunking units Connections NSV0_0004 Assembly of the trunking units, also with end flanges and feeder units, is fast and inherently secure. The trunking unit or end flange is simply inserted in the lower housing of the joint block. Once the upper part of the joint block or feeder unit is fitted, a secure connection is established by tightening four screws. The PE path is established automatically when the enclosures are connected. An expansion compensation mechanism is built into the joint block. End flanges NSV0_00042 Trunking units are available in 2 m and 3 m lengths. They consist of a galvanized metal enclosure with a light gray (RAL 703) painted finish. They are equipped with 4 busbars for L1, L2, L3 and N (aluminum conductors; copper for 160 A; silver-plated copper pick-up and connection contacts). The enclosure of the trunking unit also serves as PE conductor. Five levels of current are available in only one frame size: 40 A, 63 A, 100 A, 12 A and 160 A. The tap-off points are spaced at regular intervals of 0. m or 1 m on one side. The 2 m lengths have two or four tap-off points, the 3 m lengths have three or six. The end flanges provide touch protection against direct contact at the ends of the busbar line. They are suitable for use with all systems. Two end flanges are supplied as standard with each feeder unit. Junction units 4 L1 L2 L3 N PE NSV0_00043 The junction units, which consist of flexible conducting paths, are available in versions for 100 A and 160 A, each in 0. m and 1 m lengths. NSV0_00047 The tap-off points are finger-safe. They are opened automatically by the tap-off units and close by themselves when the tap-off units are removed. Flexible junction units mean that the busbar line can be routed in any direction. The 0. m version is recommended for right angles, the 1 m version for fitting around obstacles or for adapting to variations in height. NSV0_00044 NSV0_00046 Siemens LV 70 2009 4/3
BD01 System 40... 160 A Introduction Feeder units There is one version each for 100 A and 160 A. The feeder unit can be used as: Entry feeder unit NSV0_00048 NSV0_00049 Insulated tap-off units Common features Molded-plastic enclosure Partially transparent cover for protective devices Power pick-up through silver-plated lyre-shaped contacts Reliable prevention of incorrect mounting Cable entry is from one side only (use plastic cable glands with strain relief, not included in scope of supply). The tap-off unit must first be removed from the trunking before it can be opened and the cable can be connected. The connecting cable should be supported separately if necessary. Tap-off units with components fitted One size for 1 cylindrical fuse (10 38 mm), phase assignment L1, L2 or L3 freely selectable One size for 3 cylindrical fuses (10 38 mm) One size with 3 MW (1 MW = 18 mm; MW = modular width) There are various versions with fuse bases, miniature circuit breakers, Schuko and CEE socket outlets up to 32 A End feeder unit NSV0_0002 4 NSV0_0000 BD01-AK01X/ZS Center feeder unit NSV0_0003 NSV0_0001 BD01-AK02X/ZS3 Two end flanges are included in the scope of supply with each unit. M32, M40 and M0 cable entries are possible from four sides. For 160 A, an M63 cable entry can be fitted in a side. Plastic cable glands with strain relief must be used (not included in scope of supply). BD01-AK02M0/CEE16A163 NSV0_0004 4/4 Siemens LV 70 2009
BD01 System 40... 160 A Introduction Tap-off units for free arrangement of components One size with 3 MW; can be operated from outside through hinge switch incorporated in cover (1 MW = 18 mm; MW = modular width). Installation of devices (e.g. miniature circuit breakers) according to DIN 43871 possible up to 32 A. Tap-off units for free arrangement of components Two sizes with 4 MW and 8 MW (1 MW = 18 mm; MW = modular width) With or without device installation unit for external operation (two sizes with 4 MW and 8 MW respectively) Installation of devices (e.g. miniature circuit breakers) according to DIN 43871 possible up to 63 A. BD01-AK02M0/F Aluminum tap-off units Common features Common features: The enclosure is made from aluminum and molded plastic at both ends. A standard mounting rail is built-in for component mounting. Power pick-up through silver-plated lyre-shaped contacts The isolator built into the tap-off unit ensures that the tap-off unit is voltage-free when the cover is open. The tap-off unit can only be fitted to or removed from the tapoff point with its cover open (contacts retracted). Reliable prevention of incorrect mounting Cable entry is possible from three directions (use plastic cable glands with strain relief; not included in scope of supply). Can be combined with ancillary equipment units for additional functions. The connecting cables should be supported separately if necessary. Tap-off units with components fitted Two sizes with 4 MW or 8 MW (1 MW = 18 mm; MW = modular width) Various versions with fuse bases, miniature circuit breakers up to 63 A, with Schuko and CEE socket outlets up to 32 A. Versions with fitted miniature circuit breaker have a device installation unit. BD01-AK1M1/A161 Ancillary equipment units Common features The enclosure is made from aluminum and molded plastic at both ends. Cable entry is possible from four directions (use plastic cable glands with strain relief; not included in scope of supply). The connecting cable should be supported separately if necessary. Can be combined with tap-off or feeder units A standard mounting rail is built-in for component mounting. Two sizes with 4 MW and 8 MW (1 MW = 18 mm; MW = modular width) Without or with Schuko or CEE socket outlets With or without device installation unit for external operation (two sizes with 4 MW and 8 MW respectively) Installation of devices (e.g. fuse bases) according to DIN 43871 possible up to up to 3 A. NSV0_0008 4 BD01-GK2X/F NSV0_0006 NSV0_000 NSV0_0007 BD01-AK2M1/CEE16A163 NSV0_0009 BD01-GK2X/2SD163CEE16 Siemens LV 70 2009 4/
BD01 System 40... 160 A Introduction Accessories Optional equipment for IP Trunking units The higher degree of protection is achieved by means of additional seals and a flange at the tap-off point or connection point. With mounting position at the side, the higher degree of protection is achieved by means of additional seals and an edge protector at the sides of the feeder unit. When the feeder unit is installed at the end of a busbar line, just one seal and one edge protector are needed. NSV0_00974 Mounting position at the side: 2 BD01-KS NSV0_00971 Tap-off point: BD01-FAS NSV0_0097 4 Connection point: BD01-FS Feeder units NSV0_00972 With mounting position at the bottom, the higher degree of protection is achieved by means of additional seals and a flange at the connection point. Mounting position at the side and end of a busbar line: BD01-KS Tap-off units The higher degree of protection is achieved by means of additional seals and an edge protector at the sides of the tap-off unit. NSV0_00976 BD01-AK01X-IP, BD01-AK02X-IP NSV0_00977 NSV0_00973 BD01-AK1X-IP, BD01-AK2X-IP Mounting position at the bottom: BD01-FES 4/6 Siemens LV 70 2009
BD01 System 40... 160 A Introduction Fixing Universal fixing brackets The universal fixing brackets can be used for wall and ceiling mounting. The maximum fixing interval at normal mechanical loads is 3 m for edgewise and 1. m for flat mounting. At higher mechanical loads (e.g. pulling of plugs), an intermediate support with an additional fixing bracket at the trunking unit is recommended. Once the fixing point is decided, the tabs on the fixing bracket are pushed in to fix the busbar line. Suspension brackets The suspension brackets can be used for wall, ceiling and suspension mounting of the system. They can be fitted at any point of the trunking unit. The maximum fixing interval at normal mechanical loads is 3 m for edgewise and 1. m for flat mounting. At higher mechanical loads (e.g. pulling of plugs), an intermediate support with an additional fixing bracket at the trunking unit is recommended. NSV0_00060 NSV0_00062 BD01-BA BD01-B Hanger brackets These fixing brackets can be used for suspension of flatmounted trunking units. Also they can be fastened at the connection points in order to increase the mechanical rigidity of the trunking units. NSV0_00061 4 BD01-BAP Siemens LV 70 2009 4/7
BD01 System 40... 160 A Introduction Coding The systems can be coded for different frequencies or voltages. For this purpose, the BD01-K coding set can be fitted by the user to the installed system at each tap-off point. Four coding positions are possible. Fire protection If the busbar system is routed through a fire wall or ceiling, fire protection must be fitted. Depending on the customer's requirements, Siemens offers fire protection with a fire resistance rating of S90 (see page 4/28). Factory-fitted equipment: External fire protection as kit for mounting by the customer Mineral mortar or fire protection material to seal any gaps between the busbar trunking element and the component must be provided by the customer. NSV0_00063 Coding on the tap-off point Tap-off units can be coded on site by adapting the front face. NSV0_00064 BD01-S90 fire protection The approval papers for Germany must be ordered separately: BD01-S90-ZUL-D approval kit (certificate of approval, wall-mounted signs and declaration of conformity) NSV0_0149 4 Coding on the tap-off unit Sealing Every tap-off point on the trunking unit can be sealed. Feeder, junction, tap-off and ancillary equipment units can be made sealable with additional components (please inquire). Cable glands For the feeder, tap-off and ancillary equipment units, use plastic cable glands with strain relief (not included in scope of supply). Terminals We recommend the use of Weidmüller or Phoenix screw terminals for the N and PE conductor connections in tap-off and ancillary equipment units. 4/8 Siemens LV 70 2009
BD01 System 40... 160 A General data Technical specifications General technical specifications Type BD01-... Standards and specifications IEC/EN 60439-1 and -2 Climatic proofing Damp heat, constant, according to IEC 60068-2-78 Damp heat, cyclic, according to IEC 60068-2-30 Ambient temperature, min./max. C -/+40 Degree of protection acc. to IEC/EN 6029 Edgewise; tap-off points at the side IP4, increase to IP with optional equipment Flat; tap-off points at the bottom IP4, increase to IP with optional equipment Flat; tap-off points at the top IP0, increase to IP with optional equipment Material Trunking unit enclosures Galvanized, painted sheet steel Busbars Al or Cu Pick-up and connection contacts Cu, silver-plated Mounting position Edgewise or flat Weights See "Selection and Ordering Data" Overload and short-circuit protection Busbar trunking systems must be protected against overload and short-circuits. Fuses and miniature circuit breakers must be selected so that the admissible current carrying capacity Tap-off units corresponding with the ambient conditions is not exceeded. For overload and short-circuit protection, we recommend the use of motor protectors or circuit breakers. Type BD01-AK... Version 3- or -pole Rated current I e A 63 Switching capacity of the built-in switch-disconnector acc. to IEC/EN 60947-3 at 400 V Utilization category AC-20B Feeder and tap-off units, conductor cross-sections Version Type L1, L2, L3 N PE min. mm 2 max. mm 2 min. mm 2 max. mm 2 min. mm 2 max. mm 2 Feeder units BD01-E 6 (so, st) 0 (st) 6 (so, st) 0 (st) 6 (so, st) 0 (st) BD01-160-E 2 (st) 9 (st) 2 (st) 9 (st) 16 (st) 0 (st) Tap-off units BD01-AK01X/ZS 0.7 (f, st) 10 (so, f, st) 0.7 (f, st) 10 (so, f, st) 0.7 (f, st) 10 (so, f, st) BD01-AK02X/ZS3 0.7 (f, st) 10 (so, f, st) 0.7 (f, st) 10 (so, f, st) 0.7 (f, st) 10 (so, f, st) BD01-AK02M0/A163 0.7 (so, st) 16 (so) 0.7 (f, st) 10 (so, f, st) 0.7 (f, st) 10 (so, f, st) BD01-AK02M0/A323 0.7 (so, st) 16 (so) 0.7 (f, st) 10 (so, f, st) 0.7 (f, st) 10 (so, f, st) BD01-AK1M1/A101 0.7 (so, st) 16 (so) 0.7 (so, f) 2. (so, f) 0.7 (so, f) 2. (so, f) BD01-AK1M1/A161 0.7 (so, st) 16 (so) 0.7 (so, f) 2. (so, f) 0.7 (so, f) 2. (so, f) BD01-AK1M1/A321 0.7 (so, st) 16 (so) 0.7 (so, f) 2. (so, f) 0.7 (so, f) 2. (so, f) BD01-AK1M1/A... 0.7 (so, st) 16 (so) 0.7 (f, st) 10 (so, f, st) 0.7 (so, st) 16 (so) BD01-AK1M1/A...N 0.7 (so, st) 16 (so) 0.7 (so, st) 16 (so) 0.7 (so, st) 16 (so) BD01-AK1X/S14 0. (f, st) 4 (so) 0.7 (f, st) 10 (so, f, st) 0.7 (so, st) 16 (so) BD01-AK1X/S18 0. (f, st) 16 (so, f, st) 0.7 (f, st) 10 (so, f, st) 0.7 (so, st) 16 (so) BD01-AK1X/GB... 0.7 (so, st) 16 (so) 0.7 (f, st) 10 (so, f, st) 0.7 (so, st) 16 (so) BD01-AK2X/F141 0.7 (so, st) 16 (so) 0.7 (f, st) 10 (so, f, st) 0.7 (so, st) 16 (so) BD01-AK2X/S27 0.7 (f, st) 10 (so, f, st) 0.7 (f, st) 10 (so, f, st) 0.7 (so, st) 16 (so) BD01-AK2HX/S33 1. (f, st) 2 (f, st) 0.7 (f, st) 10 (so, f, st) 0.7 (so, st) 16 (so, st) f = finely stranded with end sleeve, so = solid, st = stranded 4 Siemens LV 70 2009 4/9
BD01 System 40... 160 A General data Trunking units 4 Type BD01-40 BD01-63 BD01-100 BD01-12 BD01-160 Conducting paths Rated insulation voltage U i V AC/DC 400/400 400/400 400/400 400/400 400/400 Overvoltage category/degree of pollution III/3 III/3 III/3 III/3 III/3 Rated operational voltage U e V AC 400 400 400 400 400 Frequency Hz 0... 60 0... 60 0... 60 0... 60 0... 60 Rated current I e conventional thermal current at max. 40 C and 3 C on a 24 h average A 40 63 100 12 160 Impedance of conducting paths at 0 Hz and 20 C busbar temperature Resistance R 20 mω/m 3.960 1.936 0.938 0.910 0.78 Reactance X 20 mω/m 0.280 0.324 0.286 0.300 0.273 Impedance Z 20 mω/m 3.970 1.968 0.994 1.000 0.642 Impedance of conducting paths under event of a fault AC resistance R F mω/m.991 4.128 2.841 2.420 2.189 Reactance X F mω/m 1.396 1.248 1.186 0.940 0.973 Impedance Z F mω/m 6.11 4.312 3.078 2.600 2.39 Zero sequence impedance acc. to IEC/EN 60909 (VDE 0102) Resistance R 0 Phase to N mω/m 1.904 7.911 4.11 3.810 3.167 Reactance X 0 Phase to N mω/m 2.128 2.08 1.797 1.630 1.66 Impedance Z 0 Phase to N mω/m 16.04 8.17 4.490 4.140 3.74 Resistance R 0 Phase to PE mω/m 10.086 8.6 6.648.430.343 Reactance X 0 Phase to PE mω/m 2.909 3.338 3.067 2.320 2.3 Impedance Z 0 Phase to PE mω/m 10.498 9.183 7.322.910.839 Short-circuit strength Rated impulse withstand current I pk ka 2. 6.30 1.30 1.30 1.30 Rated short-time withstand current I cw (t = 1 s) ka 0.8 1.1 2.0 2.0 2.0 Rated short-time withstand current I cw (t = 0.1 s) ka 1.70 4.20 9.00 9.00 9.00 Conductors Number of active conductors 4 4 4 4 4 Conductor cross-section L1, L2, L3 mm 2 7.9 1.7 34.1 34.1 34.1 N mm 2 7.9 1.7 34.1 34.1 34.1 PE (enclosure) Cu mm 2 20.0 20.0 20.0 20.0 20.0 Conductor material Al Al Al Al Cu Fire load kwh/m 0.76 0.76 0.76 0.76 0.76 Max. thermal load, I 2 t value A 2 s 10 6 0.29 1.76 8.10 8.10 8.10 Max. fixing intervals at normal mechanical load m Edgewise m 3 3 3 3 3 Flat m 1. 1. 1. 1. 1. Flat with BD01-BAP m 3 3 3 3 3 4/10 Siemens LV 70 2009
BD01 System 40... 160 A Trunking units Selection and ordering data Version Trunking units Sheet-steel enclosure, color similar to RAL 703 (light gray), codable tap-off points NSV0_00241 Rated current Length Tap-off points DT Type Order No. PS* Weight per unit Number Distance approx. A m m kg 40 3 6 0. A BD01-40-3-0, BVP:03423 1 unit 4.30 3 1 A BD01-40-3-1 BVP:2331 1 unit 4.30 2 4 0. A BD01-40-2-0, BVP:03424 1 unit 3.000 2 1 A BD01-40-2-1 BVP:2332 1 unit 3.000 63 3 6 0. A BD01-63-3-0, BVP:0342 1 unit 4.600 3 1 A BD01-63-3-1 BVP:2333 1 unit 4.600 2 4 0. A BD01-63-2-0, BVP:03426 1 unit 3.200 2 1 A BD01-63-2-1 BVP:233 1 unit 3.200 100 3 6 0. A BD01-100-3-0, BVP:03427 1 unit.200 3 1 A BD01-100-3-1 BVP:2336 1 unit.200 2 4 0. A BD01-100-2-0, BVP:03428 1 unit 3.600 2 1 A BD01-100-2-1 BVP:2337 1 unit 3.600 12 3 6 0. A BD01-12-3-0, BVP:090163 1 unit.200 3 1 A BD01-12-3-1 BVP:2339 1 unit.200 2 4 0. A BD01-12-2-0, BVP:090161 1 unit 3.600 2 1 A BD01-12-2-1 BVP:23360 1 unit 3.600 160 3 6 0. A BD01-160-3-0, BVP:090164 1 unit 8.000 3 1 A BD01-160-3-1 BVP:23363 1 unit 8.000 2 4 0. A BD01-160-2-0, BVP:090162 1 unit.400 2 1 A BD01-160-2-1 BVP:23367 1 unit.400 4 * You can order this quantity or a multiple thereof. Siemens LV 70 2009 4/11
BD01 System 40... 160 A Junction units Feeder units Selection and ordering data Version Rated current Length DT Type Order No. PS* Weight per unit approx. A m kg Junction units Flexible change of direction 100 0. A BD01-R1 BVP:034260 1 unit 1.200 1 A BD01-R2 BVP:034261 1 unit 2.00 160 0. A BD01-160-R1 BVP:090166 1 unit 1.70 1 A BD01-160-R2 BVP:090167 1 unit 3.00 NSV0_00274 Version Rated current Conductor cross-section DT Type Order No. PS* Weight per unit approx. A mm 2 kg Feeder units Molded-plastic enclosure, with 2 end flanges Can be fitted at all connection terminals and the end of the busbar run, can be combined with BD01-GK... ancillary equipment units 6 cable entries from 4 sides 100 0 1) A BD01-E BVP:03429 1 unit 1.000 Cable entry from 2 sides 160 9 2) A BD01-160-E BVP:09016 1 unit 1.400 NSV0_00243 NSV0_00242 4 Use plastic cable glands with strain relief (not included in scope of supply). 1) Use M32, M40 or M0 cable glands. 2) Use M63 cable glands. 4/12 Siemens LV 70 2009 * You can order this quantity or a multiple thereof.
BD01 System 40... 160 A Tap-off units for international use Selection and ordering data Version Rated current Rated operational voltage Tap-off units, molded plastic, size 01 With fuse base for 1 cylindrical fuse 10 mm 38 mm DT Type Order No. PS* Weight per unit approx. A V kg 16 400 A BD01-AK01X/ZS BVP:087483 1 unit 0.300 Tap-off units, molded plastic, size 02 With fuse base for 3 cylindrical fuses 10 mm 38 mm 32 400 A BD01-AK02X/ZS3 BVP:08090 1 unit 0.400 Tap-off units, molded plastic, size 02, with device installation unit With 3-pole miniature circuit breaker 16 A, characteristic B Without socket outlet 16 400 A BD01-AK02M0/A163 BVP:08089 1 unit 0.800 With 1 CEE socket outlet 16 A, -pole 16 400 A BD01-AK02M0/ CEE16A163 BVP:08092 1 unit 0.980 NSV0_00247 NSV0_00246 NSV0_0024 NSV0_00244 With 3-pole miniature circuit breaker 32 A, characteristic C 32 400 A BD01-AK02M0/A323 BVP:08094 1 unit 0.800 NSV0_00246 4 Fuse links are not included in scope of supply. Use plastic cable glands with strain relief (not included in scope of supply). * You can order this quantity or a multiple thereof. Siemens LV 70 2009 4/13
BD01 System 40... 160 A Tap-off units for international use Version Rated current Rated operational voltage DT Type Order No. PS* Weight per unit approx. A V kg Tap-off units, molded plastic, size 02, with device installation unit With 1-pole miniature circuit breaker 16 A, characteristic B With 2 Schuko socket outlets 16 A 16 230 A BD01-AK02M0/ 2SD163A161 BVP:08096 1 unit 0.700 NSV0_00248 With 1 CEE socket outlet 16 A, 3-pole 16 230 A BD01-AK02M0/ CEE163A161 BVP:090170 1 unit 0.700 With 2-pole RCCB 16 A/30 ma and with 2 Schuko socket outlets 16 A 16 230 A BD01-AK02M0/ 2SD163FIA161 BVP:090168 1 unit 0.90 With 1-pole fuse base D01 With 2 Schuko socket outlets 16 A 16 230 A BD01-AK02M0/ 2SD163S14 NSV0_00248 BVP:0809 1 unit 0.800 With 1 CEE socket outlet 16 A, 3-pole 16 230 A BD01-AK02M0/ CEE163S14 BVP:090169 1 unit 0.800 4 Freely assignable (P v max. 13 W), 3 MW (MW = modular width), with integrated standard mounting rail 32 400 A BD01-AK02M0/F BVP:08093 1 unit 0.00 NSV0_00246 NSV0_00247 NSV0_00248 NSV0_00247 Adapter ring/screw adapter, fuse links and screw cap are not included in scope of supply. Use plastic cable glands with strain relief (not included in scope of supply). 4/14 Siemens LV 70 2009 * You can order this quantity or a multiple thereof.
BD01 System 40... 160 A Tap-off units for international use Version Rated current Rated operational voltage DT Type Order No. PS* Weight per unit approx. A V kg Tap-off units, aluminum, size 1 With 1-pole fuse base D01 With 2 Schuko socket outlets 16 A 16 230 A BD01-AK1X/ 2SD163S14 BVP:034268 1 unit 1.400 With 1 CEE socket outlet 16 A, 3-pole 16 230 A BD01-AK1X/ CEE163S14 BVP:034270 1 unit 1.380 With 3-pole fuse base 3 D01 16 400 A BD01-AK1X/S14 BVP:034264 1 unit 1.400 With 3-pole fuse base 3 D02 3 400 A BD01-AK1X/S18 BVP:03426 1 unit 1.400 With 1-pole miniature circuit breaker 16 A, characteristic B With 2 Schuko socket outlets 16 A 16 230 A BD01-AK1X/ 2SD163A161 BVP:034269 1 unit 1.470 4 With 1 CEE socket outlet 16 A, 3-pole 16 230 A BD01-AK1X/ CEE163A161 BVP:034271 1 unit 1.43 Freely assignable (P v max. 13 W), 4 MW (MW = modular width), with integrated standard mounting rail 3 400 A BD01-AK1X/F BVP:034272 1 unit 1.000 NSV0_00249 NSV0_0021 NSV0_0020 NSV0_00249 NSV0_00249 NSV0_0021 NSV0_0020 Adapter ring/screw adapter, fuse links and screw cap are not included in scope of supply. Use plastic cable glands with strain relief (not included in scope of supply). * You can order this quantity or a multiple thereof. Siemens LV 70 2009 4/1
BD01 System 40... 160 A Tap-off units for international use Version Rated current Rated operational voltage DT Type Order No. PS* Weight per unit approx. A V kg Tap-off units, aluminum, size 1, with device installation unit With 3 1-pole miniature circuit breaker 10 A, characteristic B 10 400 A BD01-AK1M1/A101 BVP:203098 1 unit 1.600 With 3 1-pole miniature circuit breaker 16 A, characteristic B 16 400 A BD01-AK1M1/A161 BVP:034266 1 unit 1.600 With 3-pole miniature circuit breaker 32 A, characteristic C 32 400 A BD01-AK1M1/A323 BVP:034267 1 unit 1.600 Freely assignable (P v max. 13 W), 4 MW (MW = modular width), with integrated standard mounting rail 3 400 A BD01-AK1M1/F BVP:034273 1 unit 1.000 NSV0_0023 NSV0_0022 NSV0_0022 NSV0_0022 4 Use plastic cable glands with strain relief (not included in scope of supply). 4/16 Siemens LV 70 2009 * You can order this quantity or a multiple thereof.
BD01 System 40... 160 A Tap-off units for international use Version Rated current Rated operational voltage Tap-off units, aluminum, size 2 With 3-pole fuse base S27/S33 DT Type Order No. PS* Weight per unit approx. A V kg With 3-pole fuse base S27, gauge screw system 2 400 A BD01-AK2X/S27 BVP:034274 1 unit 1.700 With 3-pole fuse base S33, gauge screw system 63 400 A BD01-AK2HX/S33 BVP:23368 1 unit 1.700 With 2 1-pole fuse base D01 and with 4 Schuko socket outlets 16 A 16 230 A BD01-AK2X/ 4SD163S14 BVP:034277 1 unit 2.000 With 3 1-pole fuse base D01 and with 1 CEE socket outlet 16 A, -pole 16 400 A BD01-AK2X/ CEE16S14 BVP:034279 1 unit 1.80 With 3 1-pole fuse base D02 and with 1 CEE socket outlet 32 A, -pole 32 400 A BD01-AK2X/ CEE32S18 BVP:034281 1 unit 2.000 NSV0_0026 4 With 2 1-pole miniature circuit breaker 16 A, characteristic B, and with 4 Schuko socket outlets 16 A 16 230 A BD01-AK2X/ 4SD163A161 BVP:034278 1 unit 2.100 Freely assignable, 8 MW (MW = modular width), with integrated standard mounting rail NSV0_0024 NSV0_002 NSV0_0026 NSV0_002 NSV0_0024 Freely assignable (P v max. 16 W) 3 400 A BD01-AK2X/F BVP:034283 1 unit 1.300 Freely assignable (P v max. 22. W) 63 400 A BD01-AK2HX/F BVP:23370 1 unit 1.300 Adapter ring/screw adapter, fuse links and screw cap are not included in scope of supply. Use plastic cable glands with strain relief (not included in scope of supply). * You can order this quantity or a multiple thereof. Siemens LV 70 2009 4/17
BD01 System 40... 160 A Tap-off units for international use Version Rated current Rated operational voltage DT Type Order No. PS* Weight per unit approx. A V kg Tap-off units, aluminum, size 2, with device installation unit With 1-pole miniature circuit breaker 16 A, characteristic B, with 2-pole RCCB 16 A/30 ma and with 2 Schuko socket outlets 16 A 16 230 A BD01-AK2M1/ 2SD163FIA161 BVP:034276 1 unit 2.000 With 1-pole miniature circuit breaker 16 A, characteristic C, with 2-pole RCCB 2 A/30 ma and with 1 CEE socket outlet 16 A, 3-pole 16 400 A BD01-AK2M1/ CEE163FIA161 BVP:660867 1 unit 2.000 With 3-pole miniature circuit breaker 16 A, characteristic C, with 4-pole RCCB 2 A/30 ma and with 1 CEE socket outlet 16 A, -pole 16 400 A BD01-AK2M2/ CEE16FIA163 BVP:660866 1 unit 3.00 With 3-pole miniature circuit breaker 16 A, characteristic C, and with 1 CEE socket outlet 16 A, -pole 16 400 A BD01-AK2M1/ CEE16A163 BVP:034280 1 unit 2.000 4 With 3-pole miniature circuit breaker 32 A, characteristic C, and with 1 CEE socket outlet 32 A, -pole 32 400 A BD01-AK2M1/ CEE32A323 BVP:034282 1 unit 2.100 Freely assignable, 8 MW (MW = modular width), with integrated standard mounting rail NSV0_0029 NSV0_0028 NSV0_01473 NSV0_0028 NSV0_0028 NSV0_0027 Freely assignable (P v max. 16 W) 3 400 A BD01-AK2M2/F BVP:034284 1 unit 1.360 Freely assignable (P v max. 22. W) 63 400 A BD01-AK2HM2/F BVP:23371 1 unit 1.360 Use plastic cable glands with strain relief (not included in scope of supply). 4/18 Siemens LV 70 2009 * You can order this quantity or a multiple thereof.
BD01 System 40... 160 A Ancillary equipment units for international use Selection and ordering data Version Ancillary equipment units, aluminum, size 1 Freely assignable (P v max. 13 W), 4 MW (MW = modular width), with integrated standard mounting rail Can be used for Overvoltage protection Remote control/remote switching Intelligence Electronic control equipment Rated operational voltage V DT Type Order No. PS* Weight per unit approx. kg 400 A BD01-GK1X/F BVP:03428 1 unit 0.800 With 4 Schuko socket outlets 16 A 400 A BD01-GK1X/4SD163 BVP:034287 1 unit 1.200 With 1 CEE socket outlet 16 A, 3-pole 400 A BD01-GK1X/CEE163 BVP:660808 1 unit 0.90 With 1 CEE socket outlet 16 A, -pole 400 A BD01-GK1X/CEE16 BVP:660809 1 unit 1.000 NSV0_01474 4 With 1 CEE socket outlet 32 A, -pole 400 A BD01-GK1X/CEE32 BVP:660810 1 unit 1.040 Ancillary equipment units, aluminum, size 1, with device installation unit Freely assignable (P v max. 13 W), 4 MW (MW = modular width), with integrated standard mounting rail Can be used for Remote control/remote switching Intelligence Electronic control equipment Device installation unit for mounting devices, e.g. miniature circuit breakers 400 A BD01-GK1M1/F BVP:034286 1 unit 0.800 NSV0_00262 NSV0_01474 NSV0_01474 NSV0_00261 NSV0_00260 M0 cable grommets and screws for connecting the enclosure are included in scope of supply with ancillary equipment units. Use plastic cable glands with strain relief (not included in scope of supply). * You can order this quantity or a multiple thereof. Siemens LV 70 2009 4/19
BD01 System 40... 160 A Ancillary equipment units for international use Version Ancillary equipment units, aluminum, size 2 Freely assignable (P v max. 16 W), 8 MW (MW = modular width), with integrated standard mounting rail Can be used for Overvoltage protection Remote control/remote switching Intelligence Electronic control equipment Rated operational voltage V DT Type Order No. PS* Weight per unit approx. kg 400 A BD01-GK2X/F BVP:034288 1 unit 1.100 With 2 Schuko socket outlets 16 A and 1 CEE socket outlet 16 A, -pole 400 A BD01-GK2X/ 2SD163CEE16 BVP:034291 1 unit 1.600 With 2 Schuko socket outlets 16 A and 1 CEE socket outlet 32 A, -pole 400 A BD01- GK2X/2SD163CEE32 BVP:660811 1 unit 1.800 4 With 1 CEE socket outlet 16 A, 3-pole, and 1 CEE socket outlet 16 A, -pole 400 A BD01-GK2X/ CEE163CEE16 BVP:034290 1 unit 1.00 Ancillary equipment units, aluminum, size 2, with device installation unit Freely assignable (P v max. 16 W), 8 MW (MW = modular width), with integrated standard mounting rail Can be used for Remote control/remote switching Intelligence Electronic control equipment Device installation unit for mounting devices, e.g. miniature circuit breakers 400 A BD01-GK2M2/F BVP:034289 1 unit 1.100 NSV0_00266 NSV0_0026 NSV0_00264 NSV0_00264 NSV0_00263 M0 cable grommets and screws for connecting the enclosure are included in scope of supply with ancillary equipment units. Use plastic cable glands with strain relief (not included in scope of supply). 4/20 Siemens LV 70 2009 * You can order this quantity or a multiple thereof.
BD01 System 40... 160 A Tap-off units and ancillary equipment units for Belgium Selection and ordering data Version Rated current Rated operational voltage DT Type Order No. PS* Weight per unit approx. A V kg Tap-off units, aluminum, size 1 With 2-pole miniature circuit breaker 16 A, characteristic C With 2 socket outlets 16 A 16 230 X BD01-AK1X/ 2PC163A162 BVP:20311 1 unit 1.620 With 1 CEE socket outlet, 16 A, 3-pole 16 230 X BD01-AK1X/ CEE163A162 BVP:203114 1 unit 1.620 Tap-off units, aluminum, size 1, with device installation unit With 1-pole miniature circuit breaker 16 A, characteristic C With 2-pole miniature circuit breaker 16 A, characteristic C With 3-pole miniature circuit breaker 16 A, characteristic C With 3-pole and N pole miniature circuit breaker 16 A, characteristic C With 1-pole miniature circuit breaker 20 A, characteristic C With 2-pole miniature circuit breaker 20 A, characteristic C With 3-pole miniature circuit breaker 20 A, characteristic C With 3-pole and N pole miniature circuit breaker 20 A, characteristic C Tap-off units, aluminum, size 2 With 2 2-pole miniature circuit breaker 16 A, characteristic C, with 4 socket outlets 16 A 16 230 X BD01-AK1M1/A161/1 BVP:203106 1 unit 1.600 16 230 X BD01-AK1M1/A162 BVP:203110 1 unit 1.720 16 400 X BD01-AK1M1/A163 BVP:203107 1 unit 1.80 16 400 X BD01-AK1M1/A163N BVP:203111 1 unit 1.970 20 230 X BD01-AK1M1/A201 BVP:203108 1 unit 1.600 20 230 X BD01-AK1M1/A202 BVP:203112 1 unit 1.720 20 400 X BD01-AK1M1/A203 BVP:203109 1 unit 1.80 20 400 X BD01-AK1M1/A203N BVP:203113 1 unit 1.970 16 230 X BD01-AK2X/ 4PC163A162 BVP:203116 1 unit 2.320 4 Ancillary equipment units, aluminum, size 1 P v max. 13 W, with 4 socket outlets 16 A 400 X BD01-GK1X/4PC163 BVP:203117 1 unit 1.200 NSV0_00261 NSV0_002 NSV0_0022 NSV0_0021 NSV0_0020 M0 cable grommets and screws for connecting the enclosure are included in scope of supply with ancillary equipment units. Use plastic cable glands with strain relief (not included in scope of supply). * You can order this quantity or a multiple thereof. Siemens LV 70 2009 4/21
BD01 System 40... 160 A Tap-off units and ancillary equipment units for Denmark Selection and ordering data Version Rated current Rated operational voltage Tap-off units, aluminum, size 1 With 1-pole fuse base D01 and with 2 socket outlets 10 A DT Type Order No. PS* Weight per unit approx. A V kg 13 230 X BD01-AK1X/ 2DKS103S14 BVP:203099 1 unit 1.400 With 1-pole miniature circuit breaker 13 A, characteristic C, and with 2 socket outlets 10 A 13 230 X BD01-AK1X/ 2DKS103A131 BVP:203100 1 unit 1.00 Tap-off units, aluminum, size 2 With 2 1-pole fuse base D01, with 4 socket outlets 10 A 13 230 X BD01-AK2X/ 4DKS103S14 BVP:203102 1 unit 2.000 With 2 1-pole miniature circuit breaker 13 A, characteristic C, and with 4 socket outlets 10 A 13 230 X BD01-AK2X/ 4DKS103A131 BVP:203103 1 unit 2.200 4 NSV0_002 Tap-off units, aluminum, size 2, with device installation unit With 1-pole miniature circuit breaker 13 A, characteristic C, with 2-pole RCCB 16 A/30 ma and with 2 socket outlets 10 A 13 230 X BD01-AK2M1/ 2DKS103FIA131 BVP:203101 1 unit 2.000 Ancillary equipment units, aluminum, size 1 P v max. 13 W, with 4 socket outlets 10 A 400 X BD01-GK1X/4DKS103 BVP:203104 1 unit 1.200 Ancillary equipment units, aluminum, size 2 P v max. 16 W, with 2 socket outlets 10 A and 1 CEE socket outlet, 16 A, -pole 400 X BD01-GK2X/ 2DKS103CEE16 BVP:20310 1 unit 1.600 NSV0_00264 NSV0_00261 NSV0_0027 NSV0_002 NSV0_0020 NSV0_0020 Adapter rings/screw adapters, fuse links and screw cap not included in scope of supply with tap-off units. M0 cable grommets and screws for connecting the enclosure are included in scope of supply with ancillary equipment units. Use plastic cable glands with strain relief (not included in scope of supply). 4/22 Siemens LV 70 2009 * You can order this quantity or a multiple thereof.
BD01 System 40... 160 A Tap-off units for France Selection and ordering data Version Rated current Rated operational voltage Tap-off units, aluminum, size 2 With 3-pole fuse base SP1, for 3 cylindrical fuses 14 mm 1 mm DT Type Order No. PS* Weight per unit approx. A V kg 32 400 X BD01-AK2X/F141 BVP:203126 1 unit 1.700 Tap-off units, aluminum, size 2, with device installation unit With 2-pole miniature circuit breaker 16 A, characteristic B, with 2-pole RCCB 40 A/30 ma and with 2 socket outlets 16 A 16 230 X BD01-AK2M1/ 2PCUTE16AFI40 BVP:214821 1 unit 2.000 NSV0_0027 NSV0_0024 Fuse links are not included in scope of supply. Use plastic cable glands with strain relief (not included in scope of supply). 4 * You can order this quantity or a multiple thereof. Siemens LV 70 2009 4/23
BD01 System 40... 160 A Tap-off units for the United Kingdom Selection and ordering data Version Rated current Rated operational voltage DT Type Order No. PS* Weight per unit approx. A V kg Tap-off units, aluminum, size 1 With 1-pole fuse base NNS-32 Without socket outlet 32 230 X BD01-AK1X/GB321 BVP:203119 1 unit 1.100 With 2 socket outlets BS1363 13 A 13 230 X BD01-AK1X/ 2BS133GB131 BVP:203121 1 unit 1.900 With 3-pole fuse base 3 NNS-32 32 400 X BD01-AK1X/GB323 BVP:203120 1 unit 1.300 With 1-pole miniature circuit breaker 13 A, characteristic B, and with 2 socket outlets BS1363, 13 A 13 230 X BD01-AK1X/ 2BS133A131 BVP:203122 1 unit 1.720 4 NSV0_00267 Tap-off units, aluminum, size 1, with device installation unit With 3 1-pole miniature circuit breaker 32 A, characteristic C 32 400 X BD01-AK1M1/A321 BVP:203118 1 unit 1.600 Tap-off units, aluminum, size 2 With 3 1-pole fuse base NNS-32 With 1 CEE socket outlet 16 A, -pole 16 400 X BD01-AK2X/ CEE16GB163 With 1 CEE socket outlet 32 A, -pole 32 400 X BD01-AK2X/ CEE32GB323 Tap-off units, aluminum, size 2, with device installation unit With 1-pole miniature circuit breaker 13 A, characteristic B, with 2-pole RCCB 16 A/30 ma and with 1 socket outlet BS1363, 13 A 13 230 X BD01-AK2M1/ BS133FIA131 BVP:203124 1 unit 2.000 BVP:20312 1 unit 2.100 BVP:203123 1 unit 2.00 NSV0_00268 NSV0_0026 NSV0_0022 NSV0_00249 NSV0_00267 NSV0_00249 Fuse links are not included in scope of supply. Use plastic cable glands with strain relief (not included in scope of supply). 4/24 Siemens LV 70 2009 * You can order this quantity or a multiple thereof.
BD01 System 40... 160 A Tap-off units for Switzerland Selection and ordering data Version Rated current Rated operational voltage DT Type Order No. PS* Weight per unit approx. A V kg Tap-off units, aluminum, size 1, with device installation unit With miniature circuit breaker, characteristic C 3-pole, 13 A 13 400 X BD01-AK1M1/A133 BVP:611317 1 unit 1.600 3-pole, 16 A 16 400 X BD01-AK1M1/A163 BVP:611318 1 unit 1.600 3-pole, 2 A 2 400 X BD01-AK1M1/A23 BVP:611319 1 unit 1.600 Tap-off units, aluminum, size 2, with device installation unit With miniature circuit breaker, characteristic C 3-pole, 40 A 40 400 X BD01-AK2HM2/A403 BVP:611320 1 unit 2.000 3-pole, 63 A 63 400 X BD01-AK2HM2/A633 BVP:611321 1 unit 2.000 With miniature circuit breaker, characteristic C and 2 socket outlets type 23, 16 A, 3-pole 2 1-pole, 16A 16 230 X BD01-AK2M1/ 2T23-2A161 1 1-pole, 16A, and 2-pole RCCB, 16 A/30 ma With 3-pole miniature circuit breaker, 16 A, characteristic C and 1 socket outlet type 2, 16 A, -pole BVP:611310 1 unit 1.900 16 230 X BD01-AK2M1/ BVP:611311 1 unit 2.100 2T23-FI162-A161 16 400 X BD01-AK2M1/T2-A163 BVP:611314 1 unit 2.000 4 NSV0_00316 NSV0_00272 NSV0_0031 NSV0_0022 Use plastic cable glands with strain relief (not included in scope of supply). * You can order this quantity or a multiple thereof. Siemens LV 70 2009 4/2
BD01 System 40... 160 A Tap-off units for Switzerland Version Rated current Rated operational voltage DT Type Order No. PS* Weight per unit approx. A V kg Tap-off units, aluminum, size 1, with device installation unit with ancillary equipment unit, aluminum, size 1 With 3 1-pole miniature circuit breaker 16 A, characteristic C, and 3 socket outlets type 23, 16 A, 3-pole 16 230 X BD01-AK1M1/GK1X/ 3T23-3A161 BVP:611312 1 unit 2.700 Tap-off units, aluminum, size 2, with device installation unit with ancillary equipment unit, aluminum size 1 With 3 1-pole miniature circuit breaker 16 A, characteristic C, and 4-pole RCCB 2 A/30 ma with 3 socket outlets type 23, 16 A, 3-pole 16 230 X BD01-AK2M2/GK1X/ 3T23-FI24-3A161 BVP:611313 1 unit 3.00 With 3-pole miniature circuit breaker 16 A, characteristic C, and 4-pole RCCB 2 A/30 ma with 1 socket outlet type 2, 16 A, -pole 16 400 X BD01-AK2M2/GK1X/ T2-FI24-A163 BVP:61131 1 unit 3.00 4 With 3-pole miniature circuit breaker 63 A, characteristic C, and 1 CEE socket outlet 63 A, -pole 63 400 X BD01-AK2HM2/GK1X/ CEE63-A633 BVP:611316 1 unit 2.00 NSV0_00320 NSV0_00319 NSV0_00318 NSV0_00317 Use plastic cable glands with strain relief (not included in scope of supply). 4/26 Siemens LV 70 2009 * You can order this quantity or a multiple thereof.
BD01 System 40... 160 A Accessories Selection and ordering data Version DT Type Order No. PS* Weight per unit approx. kg Optional equipment for degree of protection IP For tap-off points A BD01-FAS BVP:610363 units 0.100 NSV0_00978 For connection points A BD01-FS BVP:610362 units 0.10 NSV0_00979 For feeder units Mounting position at the bottom A BD01-FES BVP:610364 1 unit 0.10 NSV0_00980 Mounting position at the side or top A BD01-KS BVP:61107 1 unit 0.030 NSV0_00981 For tap-off units Size 01X, 02X Size 01 A BD01-AK01X-IP BVP:61036 1 unit 0.00 Size 02 A BD01-AK02X-IP BVP:610366 1 unit 0.00 4 NSV0_00982 Size 1X, 2X Size 1 A BD01-AK1X-IP BVP:610367 1 unit 0.00 Size 2 A BD01-AK2X-IP BVP:610368 1 unit 0.00 NSV0_00983 * You can order this quantity or a multiple thereof. Siemens LV 70 2009 4/27
NSV0_00984 NSV0_0098 BD01 System 40... 160 A Accessories Version Rated current I e DT Type Order No. PS* Weight per unit approx. A kg Fixing Universal fixing brackets -- A BD01-B BVP:034262 1 unit 0.167 Suspension brackets -- A BD01-BA BVP:08194 1 unit 0.167 Hanger brackets For suspension by cable or pendant chain At the connection point -- A BD01-BAP BVP:20322 1 unit 0.76 Mounting parts End flanges -- A BD01-EF BVP:611071 1 unit 0.300 4 Joint blocks 100 D BD01-100-KB BVP:201966 1 unit 0.30 160 D BD01-160-KB BVP:201967 1 unit 0.30 Coding Coding sets 4 coding positions -- A BD01-K BVP:034263 10 units 0.010 Fire protection Fire protection kits for mounting by the customer with fire protection plates and fixing screws -- A BD01-S90 BVP:61134 1 unit 1.00 NSV0_01460 NSV0_00278 NSV0_00277 NSV0_00276 NSV0_0027 Fire protection approval kits (required only for Germany) -- A BD01-S90-ZUL-D BVP:611373 1 unit 0.200 4/28 Siemens LV 70 2009 * You can order this quantity or a multiple thereof.
BD01 System 40... 160 A Configuration information Overview Specimen text for tenders Item Quantity Description Unit price Amount... m Busbar trunking system (see Appendix for diagram) As type-tested low-voltage switchgear and controlgear combination (TTA) according to IEC/EN 60439-1 and -2 Rated current, corresponds to thermal rated current at max. +40 C and +3 C on a 24 h average for indoor installation Rated insulation voltage U i = 400 V AC, 400 V DC; overvoltage category/degree of pollution III/3 Operational voltage... V,... Hz Rated peak withstand current of busbar trunking system,... ka tested according to IEC/EN 60439-1 Degree of protection IP4 with tap-off points at sides and bottom, otherwise IP0; increase to IP with optional equipment -conductor system: L1, L2, L3, N, PE Busbars: silver-plated Cu connection and pick-up contacts; Al or Cu conductors; supported by insulated busbar supports Trunking units steel enclosed, galvanized and with paint finish; color: light gray, RAL 703 Halogen-free Busbar connection via joint block with built-in expansion compensation Tap-off points on one side, every 0. m or 1 m Supplied ready for connection with all assembly parts Made by Siemens Type BD01-... Comprising: 4 Siemens LV 70 2009 4/29
0,10 m BD01 System 40... 160 A Configuration information Design Fixing Wall or ceiling mounting with BD01-B 0,1 m 3 m NSV0_0006 0,1 m 4 NSV0_00066 4/30 Siemens LV 70 2009
BD01 System 40... 160 A Pendent suspension using BD01-BAP (at connection point) Configuration information < = 3 m NSV0_00067 Mounting examples with BD01-B and BD01-BA NSV0_00068 4 1, m 3 m NSV0_00069 Siemens LV 70 2009 4/31
BD01 System 40... 160 A Configuration information Function 4 Required details The following data must be considered when configuring the busbar lines: Installation flat or upright, horizontal or vertical, quantity, type and approximate ratings of prospective loads, p.f. Rated diversity factor α. If data are not available, use only the rated diversity factor Feeding transformers (short-circuit current) Nature of the installation site (dimensions, construction of the building, transport paths, cellar) Routing of supply lines from other power sources Crane operation Special requirements Operational current The operational current is calculated using the following formula: I B = P inst α b 3 U p.f. with: I B = Operational current (A) P inst = Installed power (kw) α = Rated diversity factor b = Supply factor b = 1 = Single feeder unit b = ½ = Double end feeder unit U e = Rated operational voltage (V) p.f. = Power factor If no data are available about the actual currents occurring simultaneously, the following values according to IEC/EN 60439-1 apply: Number of main circuits 2 and 3 4 and 6 to 9 inclusive 10 and more Rated diversity factor α 0.9 0.8 0.7 0.6 Short-circuit protection A system can be protected against short-circuit alone by fitting low-voltage LV HRC fuses (gl) into the incoming supply; the fuse size to be appropriate for the prospective short-circuit current at the place of installation. Overcurrent protection devices for overload and short-circuit protection Busbar trunking systems must be protected against overload and short-circuits. Fuses and miniature circuit breakers must be selected so that the admissible current carrying capacity corresponding with the ambient conditions is not exceeded. Due to their high response threshold (1.3 to 1.6 times rated current) and their long rupturing times at small overcurrents, fuses are not suitable for overload protection. Therefore we recommend the use of motor protectors or circuit breakers. The following can be used: System Overcurrent protective devices 10 3 I cc = 1 ka 1) I cc = 2 ka BD01-40 SY4 340-6 3VL27 0 BD01-63 SY4 363-6 3VL27 06 BD01-100 3VL27 10 BD01-12 3VL27 12 BD01-160 3VL27 16 1) I cf = rated conditional short-circuit current of the busbar trunking system and its outgoing feeders when protected by circuit breakers The prospective network short-circuit current and the let-through characteristic of the switches must be taken into account in each case. Temperature characteristic of BD01 systems Rated current (%) 130 120 110 100 90 80 70 NSV0_00071 - + +1 +2 +3 +4 + +6 Ambient temperature C (average over 24 hours) 4/32 Siemens LV 70 2009
BD01 System 40... 160 A Configuration information Voltage drop Voltage drop at rated current (Load distribution factor a = 1) U (V/100 m) 30 28 26 24 22 20 18 16 14 12 10 0,4 0, 0,6 0,7 0,8 0,9 40 A 63 A 12 A 160 A 100 A Calculation of the voltage drop For long busbar lines, it may be necessary to calculate the voltage drop. cos 1 NSV0_00070 Fire protection General requirements The German state building authorities demand that buildings are designed so that "spreading of fire and smoke is prevented, and that effective fire fighting and rescue of persons and domestic animals is facilitated". Fire or flue gas may not spread from one storey or fire area to another. All BD01 busbar trunking systems can be equipped with fire protection and generally comply with the standards for buildings including high-rise buildings. The fire resistance class corresponds with S 90 according to DIN 4102 Part 9. The demands for verification of fire resistance duration at 90 min as specified by ISO 834 according to IEC/EN 60439-2 are fulfilled. Configuration To ensure fire protection according to S90, the following points must be observed when configuring and installing trunking units with fire protection: The center of the fire protection in the trunking unit must be positioned in the center of the fire wall. There are no tap-off points in the area covered by the fire protection. The trunking units must be installed by an approved fire protection installation specialist. Fire protection for installation in lightweight walls are available on request. NSV0_01462 1 4 ΔU = a 3 I B l (R cos ϕ + X sinϕ) 10 3 (V) with ΔU = Voltage drop (V) I B = Operational current (A) l = Length (m) a = Load distribution factor see Table R = Ohmic resistance R 20 (mω/m) X = Inductive resistance X 20 (mω/m) cos ϕ = Power factor (p. f.) Factor a used in the equation for calculating the voltage drop is dependent on the load distribution. Load distribution A A A B B B D C C A A D D E E B E C C F B Factor a Infeed at A, one outgoing feeder at B 1 Infeed at A, outgoing feeders at B, C, D, E 0. Infeed at A, outgoing feeders at B, C 0.2 Infeed at A, outgoing feeders at B, C, D, E 0.12 Infeed at A, B, outgoing feeders at C, D, E, F 0.2 1 Packing Positioning in the fire wall Observe the following when installing the trunking units: The space $ surrounding the busbar trunking unit within the component it passes through must be packed with mineral-based mortar or fire protection sealant. The mortar or fire protection sealant must conform to the applicable regulations for establishing fire resistance rating or the construction of the wall or ceiling. The installation must be carried out according to pertinent building regulations. The approval papers can be ordered separately. 140 60 Siemens LV 70 2009 4/33
BD01 System 40... 160 A Project planning aids Dimensional drawings Trunking units BD01-... 0, L, 7, NSV0_00279 2 7 12 4, n 12 90 77 L a Number of tap-off points 2000 00 4 1000 2 3000 00 6 1000 3 20 a n a Junction units BD01(-160)-R1, BD01(-160)-R2 4 NSV0_00280 92 L1 0 7, L L2 316 NSV0_00281 R 100 Type BD01-...-R1 BD01-...-R2 L 00 1000 L1 16 66 L2 316 4/34 Siemens LV 70 2009
BD01 System 40... 160 A Project planning aids Feeder units BD01-E 170 M32, M40, M0 132 104 90 Ø,3 10 34, 27 4 11 3 9 18 260 NSV0_00282 BD01-160-E 260 20 1 M63 1 2 130 4 10 NSV0_00283 104 1 BD01-EF end flange 2 BD01-...-KB joint block Siemens LV 70 2009 4/3
BD01 System 40... 160 A Project planning aids Tap-off units Tap-off units size 01 Tap-off units size 02 BD01-AK01X/ZS BD01-AK02X/ZS3 M2 M2 77, 100 100 116 NSV0_00284 66 77. 77, 200 NSV0_0028 66 100 116 Tap-off units size 02, with device installation unit BD01-AK02M0/A163 BD01-AK02M0/A323 BD01-AK02M0/F BD01-AK02M0/2SD163S14 BD01-AK02M0/2SD163A161 BD01-AK02M0/2SD163FIA161 70 70 10 76 94 14, M2 118,2 94 76 14, M2 4 200 100 116 200 100 116 NSV0_00286 NSV0_00287 26,7 26, BD01-AK02M0/CEE163S14 BD01-AK02M0/CEE163A161 BD01-AK02M0/CEE16A163 70 76 90 2 70 10 94 10 76 94 2 102 200 100 116 200 100 116 38, NSV0_00288 38, NSV0_00289 Dashed lines: free space for opening the flap 4/36 Siemens LV 70 2009
BD01 System 40... 160 A Project planning aids Tap-off units size 1 BD01-AK1X/S... BD01-AK1X/GB... BD01-AK1X/F BD01-AK1X/2SD... BD01-AK1X/2BS... BD01-AK1X/2DKS... BD01-AK1X/2PC... 292 13 13 63 40 80 100 10 160 8 112 NSV0_00290 27 100 12 22, M2, 32, 40, 0 M2, 32, 40, 0 NSV0_00292 68 19 BD01-AK1X/CEE163... Tap-off units size 1, with device installation unit BD01-AK1M1/A... BD01-AK1M1/F 4 90 2 90 77 M2, 32, 40, 0 M2, 32, 40, 0 NSV0_00293 7, NSV0_00291 Dotted lines: usable component fitting space Dashed lines: free space for opening the flap Siemens LV 70 2009 4/37
BD01 System 40... 160 A Project planning aids Tap-off units size 2 BD01-AK2X/F..., BD01-AK2HX/F... BD01-AK2X/S..., BD01-AK2HX/S... 100 112 10 160 8 362 20 40 80 27 200 12 22, M2, 32, 40, 0 NSV0_00294 26 4 BD01-AK2X/4SD... BD01-AK2X/4DKS.. BD01-AK2X/4PC... BD01-AK2X/CEE16... BD01-AK2X/CEE32... 13 63 130 68 NSV0_00296 NSV0_00299 2 10 72, NSV0_00301 62 132 72, Dotted lines: usable component fitting space Dashed lines: free space for opening the flap 4/38 Siemens LV 70 2009
BD01 System 40... 160 A Project planning aids Tap-off units size 2, with device installation unit BD01-AK2M2/F, BD01-AK2HM2/F BD01-AK2M1/BS... BD01-AK2HM2/A... BD01-AK2M1/2SD... BD01-AK2M1/2DKS... BD01-AK2M1/2PC... BD01-AK2M1/2T23... BD01-AK2M1/T2... BD01-AK2M1/CEE163..., BD01-AK2M1/CEE16... 160 90 90 NSV0_0029 77 77 NSV0_00297 13 2 NSV0_00298 77 10 68 72, BD01-AK2M1/CEE32... BD01-AK2M2/CEE16... 90 160 4 72, 62 NSV0_00300 77 132 72, 440 2 NSV0_01476 77 10 Dotted lines: usable component fitting space Dashed lines: free space for opening the flap Siemens LV 70 2009 4/39
BD01 System 40... 160 A Project planning aids Tap-off units size 1, with device installation unit with ancillary equipment unit size 1 BD01-AK1M1/GK1X/3T23... 63 13 77 90 M2, 32, 40, 0 60, 124, NSV0_00312 Tap-off units size 2, with device installation unit with ancillary equipment unit size 1 BD01-AK2M2/GK1X/T2... BD01-AK2M2/GK1X/3T23... BD01-AK2HM2/GK1X/CEE63... 4 63 13 77 77 98 77 160 M2, 32, 40, 0 87, 160 60, 124, NSV0_00313 NSV0_00314 Dotted lines: usable component fitting space Dashed lines: free space for opening the flap 4/40 Siemens LV 70 2009
BD01 System 40... 160 A Project planning aids Ancillary equipment units Ancillary equipment units size 1 BD01-GK1X/F BD01-GK1X/4DKS103 BD01-GK1X/4PC163 BD01-GK1X/4SD163 BD01-GK1X/CEE163 BD01-GK1X/CEE16 13 17 NSV0_00302 100 10 160 13 63 M2, 32, 40, 0 NSV0_00304 10 2 60, 124, 87, NSV0_01477 BD01-GK1X/CEE32 Ancillary equipment units size 1, with device installation unit BD01-GK1M1/F 90 62 132 77 4 87, NSV0_01478 NSV0_00303 Dotted lines: usable component fitting space Dashed lines: free space for opening the flap Siemens LV 70 2009 4/41
BD01 System 40... 160 A Project planning aids Ancillary equipment units size 2 BD01-GK2X/F BD01-GK2X/CEE163CEE16 20 8 40 80 27 112 12 M2, 32, 40, 0 100 10 160 2 NSV0_0030 24 70 174 NSV0_00308 BD01-GK2X/2SD163CEE16 BD01-GK2X/2DKS103CEE16 BD01-GK2X/2SD163CEE32 Ancillary equipment units size 2, with device installation unit BD01-GK2M2/F 142 13 13 10 4 12 2 63 62 63 132 77 NSV0_00306 112 84 179 NSV0_00307 84 179 NSV0_01479 24 10 160 Dotted lines: usable component fitting space Dashed lines: free space for opening the flap 4/42 Siemens LV 70 2009
BD01 System 40... 160 A Project planning aids Protective covers according to IP For tap-off point BD01-FAS For connection point BD01-FS 92 6 11, 26 NSV0_00997 92 17 26 NSV0_00996 29 11, For feeder unit at bottom BD01-FES A A - A 12 92 4 11, A 13 NSV0_00998 172 For feeder unit at side, top BD01-KS 12 26 NSV0_00999 Siemens LV 70 2009 4/43
BD01 System 40... 160 A Project planning aids For tap-off unit BD01-AK01X-IP For tap-off unit BD01-AK02X-IP 26 12 13, NSV0_01000 NSV0_01001 11, 11, 92 92 26 12 13, For tap-off unit BD01-AK1X-IP For tap-off unit BD01-AK2X-IP 4 11, 92 11, 26 26 12 13, 12 NSV0_01002 13, NSV0_01003 92 4/44 Siemens LV 70 2009
BD01 System 40... 160 A Project planning aids Fixing Universal fixing brackets BD01-B 7 27, 2 Suspension brackets BD01-BA Ø9 103 112 132 91 0 11 13, 4, 10 NSV0_00309 27. 27, 49. 49, 2 9 NSV0_00310a 1 10 10 Ø6,6 Ø9 10 20 1 30 Hanger brackets BD01-BAP 60 230 30 9 73 92 4 NSV0_00311 12 13 48 40 10 200 20 Siemens LV 70 2009 4/4
BD01 System 40... 160 A Project planning aids Fire protection Fire protection BD01-S90 Section A-A NSV0_01461 A 134 90 100 60 A 2 69 4 4/46 Siemens LV 70 2009
BD2 System 160... 120 A Introduction /2 Overview /3 Benefits /4 Design /11 Accessories General data /14 Technical specifications Trunking units /22 Selection and ordering data Junction units /30 Selection and ordering data Feeder units /46 Selection and ordering data Tap-off units for international use /0 Selection and ordering data Ancillary equipment units for international use /60 Selection and ordering data Tap-off units for Belgium /61 Selection and ordering data Tap-off units for Denmark /62 Selection and ordering data Tap-off units for France /63 Selection and ordering data Tap-off units for the United Kingdom /64 Selection and ordering data Tap-off units for Switzerland /66 Selection and ordering data Accessories /68 Selection and ordering data Configuration information /73 Overview /7 Design /82 Function /84 Configuration /88 More information Fire protection /94 Overview /9 Design Project planning aids /102 Dimensional drawings Siemens LV 70 2009
BD2 System 160... 120 A Introduction Overview 2 2 3 4 1 3 4 4 NSV0_00081 3 1 2 3 4 Trunking unit Junction unit Feeder unit Tap-off unit Accessories /2 Siemens LV 70 2009
BD2 System 160... 120 A Introduction Tap-off units Up to 2 A - Molded-plastic enclosure - Double anti-rotation feature Up to 63 A - Sheet-steel enclosure, hot-galvanized, cover with powder-spray paint finish - Double anti-rotation feature Up to 12 A - Sheet-steel enclosure, hot-galvanized, cover with powder-spray paint finish - Compulsory order of operation - Double anti-rotation feature Up to 630 A - Sheet-steel enclosure, hot-galvanized, cover with powder-spray paint finish - Tap-off unit partitioned according to function - Enclosure for protective devices - Enclosure for power pick-up - Double anti-rotation feature Version Type-tested low-voltage switchgear and controlgear assembly (TTA) according to IEC/EN 60439-1 IEC/EN 60439-2 Degree of protection Trunking units IP2 (standard), feeder units and tap-off units IP4 Increased degree of protection to IP4 or IP with optional equipment for operation in harsh industrial environments Components Straight trunking units Without or with fire protection -wire system Busbars made of copper or aluminum Standard lengths of 3.2 m, 2.2 m and 1.2 m Selectable lengths from 0. m to 3.24 m Tap-off points - None - On two sides offset every 0.2 m or 0. m Fire protection: fire resistance class S90 and S120 according to DIN 4102, Sheet 2 to 4 Junction units Edgewise or flat With or without fire protection L-enclosure without or with configurable angle Z-enclosure T-enclosure K-enclosure Flexible junction units Feeder units Entry/end feeder unit Feeder unit with switch disconnector Benefits Center feeder unit 7 Easy and quick planning Bolt terminal Cable entry from 1, 2 or 3 sides Distribution board feeder unit Ancillary equipment units For 8 modular widths (MW) With or without device installation unit, cover powder-coated Accessories End flanges For degree of protection IP4 or IP - Flange for edgewise mounting position - Flange for flat mounting position - Flange for vertical mounting position - Additional components for tap-off units For fixing - Universal fixing bracket for edgewise or flat mounting position - Fastening elements for vertical bars, for wall or ceiling mounting Joint blocks 7 Time-saving and economical mounting 7 Reliable and safe operation 7 Flexible modular system with simple solutions for every application 7 Early planning of the power distribution system without exact knowledge of load locations 7 Early readiness for operation thanks to fast and simple mounting 7 Innovative design: No more compensation boxes to compensate elongation. 7 Codable tap-off units and tap-off points 7 Sealable throughout 7 Optional equipment for increasing the degree of protection to IP for extreme ambient conditions. Siemens LV 70 2009 /3
BD2 System 160... 120 A Introduction Design Trunking units Power is transferred through nickel-plated and tinned aluminum busbars as well as tinned copper busbars. The low inherent impedance and large surface area of the busbars limit the heat build-up. The result is a low transmission loss and a low voltage drop. Enclosures The enclosure is made of hot galvanized steel with a paint finish. Color: RAL 703 (light gray). Protected to IP2 degree of protection as standard. This can be increased to IP4 or IP with additional parts. N L1 L2 L3 ½PE 167 160... 400 A 68 BD2A-2, BD2C-2 trunking units NSV0_00084a N L1 L2 L3 ½PE 167 630... 120 A N L1 L2 L3 PE 126 Connections Trunking units are connected quickly and securely via the joint block. NSV0_00090 Left: flange cover Right: joint blocks Joint blocks Features: Even holding pressure ensures completely secure connection of all five busbars. Quick mounting up to 400 A with plug-in terminal, from 630 A to 120 A with bolt terminal. The built-in expansion compensation absorbs the heat expansion of the busbars. The terminal can be tightened using conventional tools. Two sizes are available for the whole system. The joint block is supplied as an integral part of the trunking units and junction units. N L1 L2 L3 PE 167 160... 400 A 68 NSV0_00086a 167 630... 120 A 126 NSV0_00092 BD2A-3, BD2C-3 trunking units, junction units, BD2A-..., BD2C-... feeder units Tap-off points The busbar support and tap-off point form a unit. The leading/delayed PE contact at the tap-off unit provides positive opening or closing of the tap-off point. The tap-off point can be coded at the factory on request, together with the tap-off unit. The tap-off point is sealable. BD2-AK1, BD2-AK2(3), BD2-AK02(03) and BD2-AK04 tap-off units are plug-in types for all systems, BD2-AK0(06) tap-off units are only for systems from 630 A. Left: BD2-400-SK for 160 to 400 A Right: BD2-120-EK for 630 to 120 A Four screws provide the mechanical connection to the enclosure. NSV0_00094 NSV0_00088 Left: Tap-off point for BD2.-160 to BD2.-400 Right: Tap-off point for BD2.-630 to BD2.-120 /4 Siemens LV 70 2009
BD2 System 160... 120 A Introduction Straight trunking units Flexible junction units NSV0_00097 NSV0_0009 Equipment The trunking units are available in the following versions: Without tap-off points With tap-off points on both sides at intervals of 0. m, offset by 0.2 m (BD2.-2, BD2.-3). One joint block is included in scope of supply. Fire barriers can be fitted (see "Fire barriers", page /6). The following lengths are available: 3.2 m 2.2 m 1.2 m Optional lengths Number of tap-off points Length Tap-off units on both sides m 1.2... 2.2 4... 8 2.26... 3, 2 8... 12 On optional lengths, it may not be possible to fit tap-off units to all tap-off points. Junction units NSV0_00096 BD2-...-R L-units Left: Knee, rear; BD2.-...-LH, BD2.-...-LH-X*, BD2.-...-LH-Y*, BD2.-...-LH-X*/Y* Right: Knee, front; BD2.-...-LV, BD2.-...-LV-X*, BD2.-...-LV-Y*, BD2.-...-LV-X*/Y* X X Y Y Left: Elbow, right; BD2.-...-LR, BD2.-...-LR-X*, BD2.-...-LR-Y*, BD2.-...-LR-X*/Y* Right: Elbow, left; BD2.-...-LL, BD2.-...-LL-X*, BD2.-...-LL-Y*, BD2.-...-LL-X*/Y* Z-units Y X Y NSV0_00098 NSV0_00100 X Equipment X Z Z Y Flexible copper conductors for the flexible junction units. The L-units with configurable angle are available with a fixed angle of 90 or any angle in increments from 8 to 17. Y X NSV0_00102 All L- and Z-units are available with standard limb lengths of 0.36 m one or two limb lengths selectable from 0.36 m to 1.2 m. Left: BD2.-...-ZH-Z*, BD2.-...-ZH-X*/Y*/Z* (rear) Right: BD2.-...-ZV-Z*, BD2.-...-ZV-X*/Y*/Z* (front) The junction units are supplied with one joint block. Y NSV0_00104 X Z Y Z X Left: BD2.-...-ZR-Z*, BD2.-...-ZR-X*/Y*/Z* (right) Right: BD2.-...-ZL-Z*, BD2.-...-ZL-X*/Y*/Z* (left) Siemens LV 70 2009 /
BD2 System 160... 120 A Introduction T-units Left: BD2.-...-TH (rear) Right: BD2.-...-TV (front) NSV0_00106 NSV0_00108 Fire barriers If the busbar trunking system is routed through a fire wall or ceiling, a fire barrier must be fitted. Depending on the customers requirements, Siemens offers fire barriers with a fire resistance rating of S90 and S120. Standard lengths, optional lengths and junction units are supplied with fire protective equipment as specified in the ordering data (see "Fire barriers", page /94). Factory-fitted equipment: Internal fire barriers External fire barriers, if required Documentation (certificate of approval, wall-mounted signs and declaration of conformity), for Germany as separate kit BD2-S90-ZUL-D or BD2-S120-ZUL-D Mineral based mortar or ZZ fire protection sealant TS90 (see "Fire barriers", page /101) for sealing joints between the busbar trunking element and component must be supplied by the customer. Left: BD2.-...-TR (right) Right: BD2.-...-TL (left) K-units M* NSV0_00116 NSV0_00110 BX* Left: BD2.-...-KVH (front + rear) Right: BD2.-...-KRL (right + left) L-units with engineered angle from 8 to 17 G*= 8 17 NSV0_00112 Fire barrier for trunking units and junction units For S90: For S120: BD2A-... BD2A-... or BD2C-... +BD2-S90-BX*-M* +BD2-S120-BX*-M* +BD2-S90-BY*-M* +BD2-S120-BY*-M* +BD2-S90-BZ*-M* +BD2-S120-BZ*-M* G*= 8 17 Left: Knee, rear; BD2.-...-LH-G*, BD2.-...-LH-X*-G*, BD2.-...-LH-Y*-G*, BD2.-...-LH-X*/Y*-G* Right: Knee, front; BD2.-...-LV-G*, BD2.-...-LV-X*-G*, BD2.-...-LV-Y*-G*, BD2.-...-LV-X*/Y*-G* NSV0_00114 G*= 8 17 G*= 8 17 Left: Elbow, right; BD2.-...-LR-G*, BD2.-...-LR-X*-G*, BD2.-...-LR-Y*-G*, BD2.-...-LR-X*/Y*-G* Right: Elbow, left; BD2.-...-LL-G*, BD2.-...-LL-X*-G*, BD2.-...-LL-Y*-G*, BD2.-...-LL-X*/Y*-G* /6 Siemens LV 70 2009
NSV0_00118 NSV0_00119 BD2 System 160... 120 A Introduction Feeder units For the incoming supply to BD2 runs, various feeder unit versions are available to meet different requirements. If end feeder units are used in addition to center feeder units, an additional joint block is required for each end feeder unit. NSV0_00117 Example: end feeder unit with connected cabling box Features: Cables are introduced from the front face. Cable entry plate (aluminum) for single-core cable entry. Cable connection is via bolts. The bolts are included in scope of supply. The factory-fitted jumper between PE and N can be removed for connection of five-core cables. Feeder units are supplied without joint block. For double-ended infeed, an additional joint block is required. BD2.-...-EE end feeder unit and BD2.-...-ME center feeder unit End feeder units Cable entry is from the front; cable entry from the side is possible for the version with a BD2.-...-EE-KR cabling box. NSV0_00120 BD2.-...-EE and BD2.-...-EE-KR end feeder units The phase sequence can be changed on site by rotating the busbar pack. NSV0_00122 BD2.-...-EE double-end feeder unit To distribute large amounts of power with small busbar crosssections, it is sensible to use a center feeder unit in some cases. It is mounted in the middle of a busbar line between two trunking units. The left run and the right run are supplied simultaneously with one supply cable. It is thus possible to feed in 2000 A with one 1000 A center feeder unit. In this case, special consideration must be given to the overload and short-circuit protection of the busbar system. If the short-circuit protection is not assured by the upstream protective device and/or the overload is not due to the type and number of loads, additional protective measures are required. Two options are possible: Use of a center feeder unit with one coupling unit on the right and left respectively next to the feeder unit. The coupling unit must be equipped with a protective device (fuse or circuit breaker) that ensures the short-circuit and overload function. Use of two end feeder units that are arranged centrally in the busbar line. The two supply cables are separately fused in the distribution system. End feeder units with switch disconnector End feeder units with switch disconnector NSV0_0147 Siemens LV 70 2009 /7
NSV0_00124 BD2 System 160... 120 A Introduction Distribution board feeder units For BD2 connection to a distribution board. N L1 L2 L3 PE NSV0_00129 BD2.-...-VE distribution board feeder unit Center feeder units Cable entry is possible from 3 sides. The phase sequence can be changed on site by rotating the busbar pack. BD2.-...-ME center feeder units (PE left and PE right) NSV0_0012 NSV0_00127 BD2-AK1/CEE16A163 Sheet-steel enclosed tap-off units BD2-AK2 up to 63 A and BD2-AK3 up to 12 A with cover-integrated switch-disconnector Features: Hot-galvanized sheet-steel enclosure and cover with powdercoated finish, color light gray, RAL 703. The tap-off units can be mounted and removed only with their cover open. Switch-disconnector integrated into the cover, switching capacity at 63 A AC-22B up to 400 V or at 12 A AC-21B, which ensures that the unit is not live when the cover is open. An anti-rotation feature prevents incorrect mounting. Cables can be introduced from three sides; use plastic cable glands with strain relief (not in scope of supply). Power pick-up via silver-plated lyre-shaped contacts. If the PE conductor is used as a PEN conductor, note that the PE contact of the BD2-AK3... tap-off units have only half the cross-section and therefore cannot carry the full rated current. The connecting cable should be supported separately if necessary. Device installation unit: For installing devices (e.g. miniature circuit breakers) in conformance with DIN 43871, with 8 MW. 1 MW equals a space requirement of 18 mm. Hinged covers on all tap-off units allow device operation from outside. NSV0_00200 BD2.-...-ME center feeder units (PE rear and PE front) Tap-off units Tap-off units are available in a number of versions for different applications. BD2-AK1 molded plastic-enclosed tap-off units up to 2 A, freely assignable, with fuses, miniature circuit breakers and socket outlets Features: Molded-plastic enclosure, color light gray, similar to RAL 703 Transparent cover for the protective devices During mounting and disassembly of the tap-off units, a load switching capacity of AC-22B up to 400 V is reached An anti-rotation feature prevents incorrect mounting Power pick-up through silver-plated lyre-shaped contacts Cables can be introduced from three sides The tap-off unit must be removed from the trunking before the unit can be opened and the cables connected Built-in strain relief The connecting cables should be supported separately if required BD2-AK2M2/A323 BD2-AK2 tap-off units up to 63 A, freely assignable, with fuses, miniature circuit breakers and socket outlets Features: Miniature circuit breakers can optionally be operated from the outside (device installation unit with 8 MW; 1 MW = 18 mm) BD2-AK2X/CEE32S33 NSV0_0013 /8 Siemens LV 70 2009
BD2 System 160... 120 A Introduction BD2-AK3 tap-off units up to 12 A with fuse switch-disconnectors and fuse bases Features: On versions with fuse switch-disconnectors or circuit breakers, the cover is interlocked with these switches and can therefore be opened only when they are switched off. On versions with fuse bases, the isolator built into the cover does not disconnect the load. It only removes the voltage from the installed fuse bases when the cover is opened. Terminal bolts for cables. NSV0_00136 BD2-AK3X/GSTZ00 Tap-off units BD2-AK2 up to 63 A and BD2-AK3 up to 12 A equipped to customer specifications Features: Device installation to customer specification in compliance with the requirements for type-tested low-voltage switchgear and controlgear assemblies (TTA). Configuration, quotations and delivery through your Siemens contacts in our branches. Devices mounted on pre-drilled mounting plates, module mounting rails or top-hat rails according to EN 6071. BD2-AK02 (AK03) sheet-steel enclosed tap-off units without cover-integrated switch-disconnector Features: Hot-galvanized, sheet-steel enclosure and cover with powdercoated finish, color light gray, RAL 703. The tap-off units can be mounted and removed with their cover open and closed. With the cover open the voltage is still applied to the installed devices (test facility). Degree of protection IP20 (finger-safe) is assured. Do not mount or remove tap-off units under load. An anti-rotation feature prevents incorrect mounting. Cables can be introduced from three sides; use plastic cable glands with strain relief (not in scope of supply). Power pick-up via silver-plated lyre-shaped contacts. If the PE conductor is used as a PEN conductor, note that the PE contact of the BD2-AK03 tap-off units have only half the cross-section and therefore cannot carry the full rated current. The connecting cable should be supported separately if necessary. Device installation unit: For installing devices (e.g. miniature circuit breakers) in conformance with DIN 43871, with 8 MW. 1 MW equals a space requirement of 18 mm. Hinged covers on all tap-off units allow device operation from outside. BD2-AK02 tap-off units up to 63 A, freely assignable, with fuses, miniature circuit breaker Features: Miniature circuit breakers can optionally be operated from the outside (device installation unit with 8 MW; 1 MW = 18 mm) NSV0_00138 NSV0_00131 BD2-AK2... BD2-AK02M2/A323 Siemens LV 70 2009 /9
BD2 System 160... 120 A Introduction BD2-AK03 tap-off units up to 12 A with circuit breakers, fuse switch-disconnectors, fuse bases, miniature circuit breakers and fuse-switches Features: On versions with fuse switch-disconnectors or circuit breakers, the cover is interlocked with these switches and can therefore be opened only when they are switched off. Terminal bolts for cables Miniature circuit breakers can optionally be operated from the outside (device installation unit with 8 MW; 1 MW = 18 mm) The connecting cable should be supported separately if necessary. On versions with fuse switch-disconnectors or circuit breakers, the cover is interlocked with these switches and can therefore be opened only when they are switched off. On versions with fuse bases, the load must be disconnected before the enclosure cover is removed. Connections for multi-core or single-core cables are possible. NSV0_0146 BD2-AK03X/L... Tap-off units BD2-AK02 up to 63 A and BD2-AK03 up to 12 A equipped to customer specifications Features: Device installation to customer specification in compliance with the requirements for type-tested low-voltage switchgear and controlgear assemblies (TTA). Engineering, quotations and delivery through your Siemens contacts in our branches. Devices mounted on pre-drilled mounting plates, module mounting rails or top-hat rails according to EN 6071 NSV0_00133 BD2-AK03... Steel enclosed tap-off units BD2-AK04 up to 20 A and BD2-AK0 up to 400 A and BD2-AK06 up to 630 A without cover-integrated switch-disconnector Tap-off units BD2-AK04 up to 20 A, BD2-AK0 up to 400 A and AK06 up to 630 A with circuit breakers, fuse switch-disconnectors and fuse bases Features: Type BD2-AK0 and BD2-AK06 tap-off units > 20 A can be mounted only on 630 A to 120 A trunking units. Hot-galvanized and powder-coated sheet-steel enclosure, color light gray, RAL 703. The tap-off units can be mounted and removed only with their cover open. An anti-rotation feature prevents incorrect mounting. Cables can be introduced from three sides; use plastic cable glands with strain relief (not in scope of supply). Power pick-up through silver-plated lyre-shaped contacts If the PE conductor is used as a PEN conductor, note that the PE contact of the BD2-AK04, BD2-AK0 and BD2-AK06 tap-off units have only half the cross-section and therefore cannot carry the full rated current. BD2-AK0/LS... Ancillary equipment units Features: The enclosure is made from hot-galvanized sheet steel. Cables can be introduced from 4 sides (use plastic cable glands with strain relief; not in scope of supply). Can be combined with tap-off units (BD2-AK02, AK2, AK03, AK3) A standard mounting rail is built-in for component mounting. 1 size with 8 MW (1 MW = 18 mm; MW = modular width). Without or with device installation unit for external operation (1 size with 8 MW). Installation of devices (e.g. miniature circuit breakers) in accordance with DIN 43871 possible up to and including 63 A. BD2-GKM2/F NSV0_01014 NSV0_00139 /10 Siemens LV 70 2009
NSV0_00148 BD2 System 160... 120 A Introduction Accessories Protective sleeve Provides purely mechanical protection for the busbar system when it is routed through walls and ceilings. The protective sleeve can be retrofitted. Flat mounting position The higher degree of protection is achieved by fitting an additional flange at the connection points, at the end flange and at the tapoff points. 0,18 NSV0_00140 NSV0_0014 BD2-400-D and BD2-120-D protective sleeve for currents up to 400 A or from 630 to 120 A End flanges An end flange is required for terminating the busbar line. Two sizes are available. Left: Connection point between trunking units with BD2-FF Right: Connection point between trunking unit and end flange with BD2-FFE NSV0_00147 NSV0_00141 Left: BD2-400-FE end flange for currents up to 400 A Right: BD2-120-FE end flange for currents from 630 to 120 A Optional equipment for degree of protection IP4 Edgewise mounting position The higher degree of protection is achieved by fitting an additional flange at the connection points and at the end flange. Tap-off openings with BD2-FAS Vertical mounting position The higher degree of protection is achieved by fitting additional flanges at all the connection points and at all tap-off points (front and rear). NSV0_00143 Left: Connection point between trunking units with BD2-...-HF Right: Connection point between trunking unit and end flange with BD2-...-HFE Left: Connection point between trunking units with BD2-...-VF Right: Tap-off openings with BD2-FAS Siemens LV 70 2009 /11
BD2 System 160... 120 A Introduction Optional equipment for degree of protection IP Trunking units The higher degree of protection IP is achieved by fitting additional seals and a flange at the connection points and at the tap-off points. Tap-off units The higher degree of protection IP is achieved by fitting additional seals at the tap-off unit. NSV0_01004 BD2-AK1-IP Connection point between trunking units with BD2-...-FS NSV0_01007 NSV0_0100 Connection point between trunking unit and end flange with BD2-...-FSE BD2-AK2X(3X)-IP NSV0_00147 Tap-off openings with BD2-...-FAS BD2-AK02X(03X)-IP NSV0_01009 NSV0_01008 NSV0_01006 BD2-AK04(0, 06)-IP /12 Siemens LV 70 2009
BD2 System 160... 120 A Introduction Accessories for fixing Fixing brackets The universal fixing bracket can be used for edgewise and flat mounting of all trunking versions. NSV0_0010 Retaining elements for vertical busbar lines These consist of a wall mounting element and accessories for fixing to to the ceiling. The retaining elements are adjustable to compensate for uneven walls. Maximum load carrying capacity of retaining element, see "Configuration Information", page /82. BD2-400-BB and BD2-120-BB fixing bracket for currents up to 400 A or from 630 to 120 A Spacer brackets Spacer brackets for compensating building tolerances between trunking unit and wall or ceiling. The spacer bracket slides onto the BD2-...-BB fixing bracket and is secured with screws. For vertically mounted BD2 runs, it can also be used as an intermediate mounting. NSV0_0014 BD2-BWV wall mounting element for busbar line and end feeder unit At the transition from the horizontal to the vertical busbar line, the ceiling mounting must be used as a support element. NSV0_0012 BD2-BD spacer brackets Spacers Spacers for compensating wall and ceiling discrepancies between feeder units and trunking units. The spacers clip onto the fixing bracket. NSV0_001 NSV0_0013 BD2-DSB spacers BD2-BDV ceiling mounting element for busbar line NSV0_0016 BD2-BVF wall mounting element for busbar line at each joint block Siemens LV 70 2009 /13
BD2 System 160... 120 A General data Technical specifications General system data Type BD2-... Standards and specifications IEC/EN 60439-1 and -2 Rated insulation voltage U i V AC/DC 690/800 Overvoltage category/degree of pollution III/3 Rated operational voltage U e V AC 690 Frequency Hz 0... 60 Rated operational current I e Aluminum busbars A 160... 1000 Copper busbars A 160... 120 Climatic proofing Damp heat, constant, according to IEC 60068-2-78 Damp heat, cyclic, according to IEC 60068-2-30 Ambient temperature C -... +40 Degree of protection according to IEC/EN 6029 (installation type 2) Trunking units IP2 Trunking units with optional equipment on the busbar IP4, IP line Feeder units, tap-off units IP4 Feeder units and tap-off units with accessories IP Material Trunking units, feeder units, tap-off units Hot-galvanized, painted sheet steel, light gray (RAL 703) Exception: BD2-AK1/... tap-off units Molded-plastic enclosure, light gray (RAL 703) Busbars -Aluminum Nickel-plated and tinned aluminum busbars - Copper Tinned copper busbars Mounting position Edgewise, flat, tap-off points on side Weights See "Selection and Ordering Data" Tap-off units Type BD2-AK... Rated current I e 2 A 63 A 12 A 20 A 400 A 630 A Switching capacity of contact system AC-22B -- -- -- -- -- Switching capacity of the built-in switch-disconnector according to IEC/EN 60947-3 at 400 V -- AC-22B AC-21B -- -- -- Max. admissible rated prospective short-circuit withstand current when tap-off units with miniature circuit breakers are used: Important configuring notes Not all tap-off units have a rated voltage of 690 V and a shortcircuit strength that corresponds to the system as a whole. The short-circuit strength and rated voltage of the tap-off units used in a system must be appropriate for it. If the rated voltage of a tap-off unit does not match, choose one equipped with the appropriate components. Larger prospective short-circuit currents must be limited by fitting protection equipment (such as circuit breakers) upstream. 10 kaeff: For higher rated prospective short-circuit currents, refer to "Back-up protection" for miniature circuit breakers. 2 kaeff: For higher rated prospective short-circuit currents, the upstream protective device must limit to: Max. let-through energy I 2 t = 12 10 4 A 2 s; Max. let-through current I D =9.kA /14 Siemens LV 70 2009
BD2 System 160... 120 A General data Trunking units with aluminum conductor Type BD2A-.-160 BD2A-.-20 BD2A-.-400 Conducting paths Rated insulation voltage U i V AC/DC 690/800 690/800 690/800 Overvoltage category/degree of pollution III/3 III/3 III/3 Rated operational voltage U e V AC 690 690 690 Frequency Hz 0... 60 0... 60 0... 60 Rated current I e = thermal rated current at A 160 20 400 max. 40 C and 3 C on 24 h average Impedance per unit length of conducting paths with 0 Hz and 20 C ambient temperature (cold bars) Equivalent resistance R 20 mω/m 0.484 0.302 0.167 Positive reactance X 20 mω/m 0.162 0.131 0.123 Impedance Z 20 mω/m 0.11 0.330 0.207 Impedance per unit length of conducting paths with 0 Hz and 20 C ambient temperature (bar under warm operating conditions) Equivalent resistance R 1 mω/m 0.88 0.37 0.21 Positive reactance X 1 mω/m 0.160 0.128 0.122 Impedance Z 1 mω/m 0.610 0.397 0.247 Impedance of conducting paths in the event of a fault AC resistance per unit length R F mω/m 0.99 0.673 0.48 Positive reactance per unit length X F mω/m 0.681 0.487 0.46 Impedance per unit length Z F mω/m 1.19 0.831 0.713 Zero sequence impedance according to Phase to N R 0 mω/m 2.00 1.340 1.217 IEC/EN 60909 (VDE 0102) X 0 mω/m 0.884 0.70 0.640 Z 0 mω/m 2.232 1.3 1.37 Phase to PE R 0 mω/m 2.018 1.071 1.09 X 0 mω/m 0.416 0.67 0.18 Z 0 mω/m 2.061 1.212 1.179 Short-circuit strength Rated impulse withstand current I pk ka 17 32 40 Rated short-time withstand current I cw t = 1 s ka. 10 16 t = 0.1 s ka 10 16 20 Number of conductors Conductor cross-section L1, L2, L3 mm 2 63 93 20 N mm 2 63 93 20 PE mm 2 63 93 20 1 / 2 PE mm 2 63 93 20 Conductor material Al Al Al Max. interval between trunking unit supports at normal mechanical loading Edgewise m 4 4 4 Edgewise with BD2-BD 1) m 4 4 4 Flat m 3. 3. 3. Fire load 2) kwh/m 1.32 1.32 1.32 1) When using BD2-BD spacer bracket. 2) Values for trunking units with tap-off points. For more values, see page /21. Siemens LV 70 2009 /1
BD2 System 160... 120 A General data Trunking units with aluminum conductor Type BD2A-.-630 BD2A-.-800 BD2A-.-1000 Conducting paths Rated insulation voltage U i V AC/DC 690/800 690/800 690/800 Overvoltage category/degree of pollution III/3 III/3 III/3 Rated operational voltage U e V AC 690 690 690 Frequency Hz 0... 60 0... 60 0... 60 Rated current I e = thermal rated current at A 630 800 1000 max. 40 C and 3 C on 24 h average Impedance per unit length of conducting paths with 0 Hz and 20 C ambient temperature (cold bars) Equivalent resistance R 20 mω/m 0.113 0.073 0.01 Positive reactance X 20 mω/m 0.07 0.08 0.08 Impedance Z 20 mω/m 0.127 0.094 0.077 Impedance per unit length of conducting paths with 0 Hz and 20 C ambient temperature (bar under warm operating conditions) Equivalent resistance R 1 mω/m 0.149 0.098 0.066 Positive reactance X 1 mω/m 0.07 0.07 0.07 Impedance Z 1 mω/m 0.19 0.114 0.088 Impedance of conducting paths in the event of a fault AC resistance per unit length R F mω/m 0.264 0.22 0.17 Positive reactance per unit length X F mω/m 0.238 0.239 0.240 Impedance per unit length Z F mω/m 0.3 0.328 0.287 Zero sequence impedance according to Phase to N R 0 mω/m 0.38 0.494 0.340 IEC/EN 60909 (VDE 0102) X 0 mω/m 0.331 0.312 0.301 Z 0 mω/m 0.632 0.84 0.44 Phase to PE R 0 mω/m 0.492 0.438 0.408 X 0 mω/m 0.303 0.280 0.273 Z 0 mω/m 0.78 0.20 0.491 Short-circuit strength Rated impulse withstand current I pk ka 64 84 90 Rated short-time withstand current I cw t = 1 s ka 26 32 34 t = 0.1 s ka 32 40 43 Number of conductors Conductor cross-section L1, L2, L3 mm 2 277 486 699 N mm 2 277 486 699 PE mm 2 277 486 699 1 / 2 PE mm 2 277 277 486 Conductor material Al Al Al Max. interval between trunking unit supports at normal mechanical loading Edgewise m 4 3. 3 Edgewise with BD2-BD 1) m 2 1.7 1. Flat m 3. 3 2. Fire load 2) kwh/m 2 2 2 1) When using BD2-BD spacer bracket. 2) Values for trunking units with tap-off points. For more values, see page /21. /16 Siemens LV 70 2009
BD2 System 160... 120 A General data Trunking units with copper conductor Type BD2C-.-160 BD2C-.-20 BD2C-.-400 Conducting paths Rated insulation voltage U i V AC/DC 690/800 690/800 690/800 Overvoltage category/degree of pollution III/3 III/3 III/3 Rated operational voltage U e V AC 690 690 690 Frequency Hz 0... 60 0... 60 0... 60 Rated current I e = thermal rated current at A 160 20 400 max. 40 C and 3 C on 24 h average Impedance per unit length of conducting paths with 0 Hz and 20 C ambient temperature (cold bars) Equivalent resistance R 20 mω/m 0.303 0.29 0.144 Positive reactance X 20 mω/m 0.17 0.18 0.119 Impedance Z 20 mω/m 0.341 0.33 0.187 Impedance per unit length of conducting paths with 0 Hz and 20 C ambient temperature (bar under warm operating conditions) Equivalent resistance R 1 mω/m 0.333 0.383 0.181 Positive reactance X 1 mω/m 0.17 0.19 0.120 Impedance Z 1 mω/m 0.368 0.419 0.217 Impedance of conducting paths in the event of a fault AC resistance per unit length R F mω/m 0.666 0.674 0.364 Positive reactance per unit length X F mω/m 0.11 0.30 0.461 Impedance per unit length Z F mω/m 0.839 0.88 0.87 Zero sequence impedance according to Phase to N R 0 mω/m 1.419 1.429 0.718 IEC/EN 60909 (VDE 0102) X 0 mω/m 0.691 0.703 0.68 Z 0 mω/m 1.79 1.93 0.974 Phase to PE R 0 mω/m 1.027 1.139 0.672 X 0 mω/m 0.641 0.30 0.03 Z 0 mω/m 1.211 1.26 0.839 Short-circuit strength Rated impulse withstand current I pk ka 17 32 40 Rated short-time withstand current I cw t = 1 s ka. 10 16 t = 0.1 s ka 10 16 20 Number of conductors Conductor cross-section L1, L2, L3 mm 2 63 63 147 N mm 2 63 63 147 PE mm 2 63 63 147 1 / 2 PE mm 2 63 63 147 Conductor material Cu Cu Cu Max. interval between trunking unit supports at normal mechanical loading Edgewise m 4 4 4 Edgewise with BD2-BD 1) m 4 4 4 Flat m 3. 3. 3. Fire load 2) kwh/m 1.32 1.32 1.32 1) When using BD2-BD spacer bracket. 2) Values for trunking units with tap-off points. For more values, see page /21. Siemens LV 70 2009 /17
BD2 System 160... 120 A General data Trunking units with copper conductor Type BD2C-.-630 BD2C-.-800 BD2C-.-1000 BD2C-.-120 Conducting paths Rated insulation voltage U i V AC/DC 690/800 690/800 690/800 690/800 Overvoltage category/degree of pollution III/3 III/3 III/3 III/3 Rated operational voltage U e V AC 690 690 690 690 Frequency Hz 0... 60 0... 60 0... 60 0... 60 Rated current I e = thermal rated current at A 630 800 1000 120 max. 40 C and 3 C on 24 h average Impedance per unit length of conducting paths with 0 Hz and 20 C ambient temperature (cold bars) Equivalent resistance R 20 mω/m 0.069 0.069 0.043 0.032 Positive reactance X 20 mω/m 0.04 0.04 0.06 0.04 Impedance Z 20 mω/m 0.088 0.088 0.071 0.063 Impedance per unit length of conducting paths with 0 Hz and 20 C ambient temperature (bar under warm operating conditions) Equivalent resistance R 1 mω/m 0.087 0.091 0.06 0.041 Positive reactance X 1 mω/m 0.04 0.04 0.06 0.04 Impedance Z 1 mω/m 0.102 0.106 0.079 0.068 Impedance of conducting paths in the event of a fault AC resistance per unit length R F mω/m 0.173 0.172 0.118 0.094 Positive reactance per unit length X F mω/m 0.226 0.229 0.234 0.229 Impedance per unit length Z F mω/m 0.28 0.286 0.262 0.248 Zero sequence impedance according to Phase to N R 0 mω/m 0.37 0.373 0.234 0.186 IEC/EN 60909 (VDE 0102) X 0 mω/m 0.296 0.266 0.286 0.27 Z 0 mω/m 0.464 0.48 0.370 0.332 Phase to PE R 0 mω/m 0.342 0.334 0.230 0.174 X 0 mω/m 0.283 0.284 0.278 0.26 Z 0 mω/m 0.444 0.438 0.361 0.317 Short-circuit strength Rated impulse withstand current I pk ka 64 84 90 90 Rated short-time withstand current I cw t = 1 s ka 26 32 34 34 t = 0.1 s ka 32 40 43 43 Number of conductors Conductor cross-section L1, L2, L3 mm 2 280 280 468 699 N mm 2 280 280 468 699 PE mm 2 280 280 468 699 1 / 2 PE mm 2 280 280 280 468 Conductor material Cu Cu Cu Cu Max. interval between trunking unit supports at normal mechanical loading Edgewise m 4 3. 3 2 Edgewise with BD2-BD 1) m 2 1.7 1. 1 Flat m 3. 3 2. 1. Fire load 2) kwh/m 2 2 2 2 1) When using BD2-BD spacer bracket. 2) Values for trunking units with tap-off points. For more values, see page /21. /18 Siemens LV 70 2009
BD2 System 160... 120 A General data Feeder units Conductor cross-sections Version Type L1, L2, L3 N PE Size of terminal screws, bolts L1, L2, L3, N, PE Feeder units with bolt terminal Feeder units with switch disconnector Center feeder units with bolt terminal min. mm 2 1) Minimum possible cable cross-section for cable lugs. max. mm 2 BD2.-20-EE (1 3) 6 1 10, 2 70 BD2.-400-EE (1 3) 10 1) 1 240, 2 120 BD2.-1000-EE (1 3) 10 1) 2 240, 3 18 BD2.-120-EE (1 4) 10 1) 3 300, 4 240 BD2C-20 (31, 400)-EESC BD2C-630 (800 -EESC BD2.-400-ME (1 3) 10 1) 2 240, 3 18 min. mm 2 max. mm 2 (1 3) 6 1 10, 2 70 (1 3) 10 1) 1 240, 2 120 (1 3) 10 1) 2 240, 3 18 (1 4) 10 1) 3 300, 4 240 min. mm 2 max. mm 2 (1 3) 6 1 10, 2 70 (1 3) 10 1) 1 240, 2 120 (1 3) 10 1) 2 240, 3 18 (1 4) 10 1) 3 300, 4 240 1 10 1) 1 240 1 10 1) 1 240 Armoring M12 1 10 1) 2 240 1 10 1) 2 240 Armoring M12 (1 3) 10 1) 2 240, 3 18 (1 3) 10 1) 2 240, 3 18 BD2.-1000-ME (1 ) 10 1) (1 ) 300 (1 ) 10 1) (1 ) 300 (1 ) 10 1) (1 ) 300 M12 M10 M12 M12 M12 M12 Cable and wiring entries Type BD2.-20-EE BD2.-400-EE BD2.-1000-EE, BD2.-1000-ME BD2.-120-EE BD2.-400-ME Cable grommets 1 KT3 1) 2 KT4 1) 3 KT4 1) 6 KT4 1) 4 KT4 1) For cable diameter mm 14... 4 14... 68 14... 68 14... 68 14... 68 1) With strain relief. Cable entry plate for single core cable (undrilled cable entry plates) Type BD2.-20-EE BD2.-400-EE BD2.-1000-EE BD2.-120-EE Cable entry plate BD2-20-EBAL BD2-400-EBAL BD2-1000-EBAL BD2-120-EBAL Number of cable entries (maximum) 10 M32, 10 M40 1 M40, 36 M0 M40 6 M0 and 4 M40 Use plastic cable glands with strain relief (not included in scope of supply). Cable entry plate for single core cable with center feeder units (undrilled cable entry plates) Type BD2.-400-ME... BD2.-1000-ME Cable entry plate BD2-400-MBAL BD2-1000-MBAL Number of cable entries (maximum) 12 M40 and 3 M32, 31 M40, 6 M0 and 4 M40 16 M0 and 4 M40 Use plastic cable glands with strain relief (not included in scope of supply). Siemens LV 70 2009 /19
BD2 System 160... 120 A General data Tap-off units Conductor cross-sections Designation Type L1, L2, L3 N PE Size of terminal screws, min. max. min. max. min. max. mm 2 mm 2 mm 2 mm 2 mm 2 mm 2 Up to 2 A BD2-AK1/S14 0. (f, st) 4 (so) 1 (so, f, st) 6 (so, st) 1 (so, f, st) 6 (so, st) BD2-AK1/S18 0. (f, st) 16 (so, f, st) 1 (so, f, st) 6 (so, st) 1 (so, f, st) 6 (so, st) BD2-AK1/A... 0.7 (so, st) 16 (so) 1 (so, f, st) 6 (so, st) 1 (so, f, st) 6 (so, st) BD2-AK1/A...N 0.7 (so, st) 16 (so) 0.7 (so, st) 16 (so) 1 (so, f, st) 6 (so, st) BD2-AK1/F... 0.7 (so, st) 16 (so) 1 (so, st) 6 (so) 1 (so, f, st) 6 (so, st) BD2-AK1/F...N 0.7 (so, st) 16 (so) 0.7 (so, st) 16 (so) 1 (so, f, st) 6 (so, st) Up to 63 A BD2-AK.2X/S18 0. (f, st) 2 (f, st) 1 (so, f, st) 6 (so, st) 1 (so, f, st) 6 (so, st) BD2-AK.2X/S27 0.7 (f, st) 10 (so, f, st) 1 (so, f, st) 6 (so, st) 1 (so, f, st) 6 (so, st) BD2-AK.2X/S33 1. (f, st) 2 (f, st) 2. (so, f, st) 16 (so, st) 2. (so, f, st) 16 (so, st) BD2-AK.2M2/A... 0.7 (so, st) 2 (st) 2. (so, f, st) 2 (st) 2. (so, f, st) 2 (st) BD2-AK.2M2/A...N 0.7 (so, st) 2 (st) 0.7 (so, f, st) 2 (st) 2. (so, f, st) 2 (st) BD2-AK.2X/F... 0.7 (so, st) 2 (st) 2. (so, f, st) 2 (st) 2. (so, f, st) 2 (st) BD2-AK.2X/GB32... 0.7 (so, st) 16 (so, st) 0.7 (so, st) 16 (so, st) Armoring BD2-AK.2X/GB63... 0.7 (so, st) 0 (st) 0.7 (so, st) 0 (st) Armoring Up to 12 A BD2-AK03X/LSD40-LSD12 2. (so, st) 0 (st) 2. (so, st) 0 (st) 2. (so, st) 0 (st) BD2-AK3X/GS00 16 70 16 70 10 70 M8 BD2-AK.3X/GSTZ(A)00 16 70 16 70 10 70 M8 BD2-AK.3X/GB100... 6 (so, st) 70 (st) 6 (so, st) 70 (st) Armoring BD2-AK03X/T(S)PNR100... 6 (so, st) 0 (st) 6 (so, st) 0 (st) Armoring Up to 20 A BD2-AK04/SNH1 6 10 6 10 6 10 M10 BD2-AK04/FS... 6 10 6 10 6 10 M10 BD2-AK04/LS... 6 120 (st) 6 (so, st) 10 6 10 M8 Up to 400 A BD2-AK0/SNH2 10 2 120 10 2 120 10 2 120 M10 BD2-AK0/FS... 10 2 120 10 2 120 10 2 120 M10 BD2-AK0/LS... 10 2 120 10 2 120 10 2 120 M8 Up to 630 A BD2-AK06/SNH3 10 2 240 10 2 240 10 2 240 M12 BD2-AK06/LS... 10 2 240 10 2 240 10 2 240 M10 so = solid, st = stranded, f = finely stranded with end sleeve bolts L1, L2, L3 Cable and wiring entries Type BD2-AK1/... BD2-AK.2... BD2-AK.3... BD2-AK04 BD2-AK0 BD2-AK06 Cable grommets M2 2) KT 3 3) 2 KT 4 3) 2 KT 4 3) Cable glands 1) M2, M32, M40 M2, M40, M63 For cable diameter mm 11... 16 11... 27 11... 42 14... 4 14... 68 14... 68 Min./max. cable entry capacity for multi-core cables NYY... mm 2 1. to 4 NYCWY... 4) mm 2 4 1. to 4 2. Cable entry plate for singe-core cable (plates fitted, undrilled) 1) For cable glands: Use plastic cable glands with strain relief (not included in scope of supply). 2) Strain relief in BD2-AK1/... 3) With strain relief. 4) Fifth conductor: concentric conductor. 1. to 16 4 1. to 4 16 1. to 2 4 1. to 4 70 1. to 4 10 2 1. to 2 4 10 Max. number of cable entries 10 M40 10 M32, M40 2 10 to 2 4 240 10 M40 /20 Siemens LV 70 2009
BD2 System 160... 120 A General data Fire loads Type Fire load Type Fire load Type Fire load (without single-bolt terminal block) kwh/m kwh kwh Trunking units Tap-off units BD2-AK.3X/LSD40-4 12.8 BD2.-.-160-SB-. 1.32 BD2-AK1/S14 6.9 BD2-AK.3X/LSD63-4 12.8 BD2.-.-160-WB-. 1.32 BD2-AK1/S18 6.9 BD2-AK.3X/LSD80-4 12.8 BD2.-.-20-SB-. 1.32 BD2-AK1/A163.83 BD2-AK.3X/LSD100-4 12.8 BD2.-.-20-WB-. 1.32 BD2-AK1/CEE16S14 8. BD2-AK.3X/LSD12-4 12.8 BD2.-.-400-SB-. 1.32 BD2-AK1/CEE16A163 8.7 BD2-AK.3X/GS00 8.07 BD2.-.-400-WB-. 1.32 BD2-AK1/2CEE163S14 9. BD2-AK.3X/GST.00 9.07 BD2.-.-400-SO-. 0.60 BD2-AK1/2CEE163A161 7. BD2-AK.3X/GB1003 14 BD2.-.-400-WO-. 0.60 BD2-AK1/3SD163S14 8 BD2-AK03X/FS12...-3 10.0 BD2.-.-630-SB-. 2.00 BD2-AK1/3SD163A161 8.3 BD2-AK03X/FS12...-4 13.0 BD2.-.-630-WB-. 2.00 BD2-AK1/A161/1. BD2-AK03X/F228...-3(N) 6.1 BD2.-.-630-SO-. 0.67 BD2-AK1/A162. BD2-AK03M2/A123(N).7 BD2.-.-630-WO-. 0.67 BD2-AK1/A163N 6.1 BD2-AK04/SNH1 10.12 BD2.-.-800-SB-. 2.00 BD2-AK1/2CEE163A162 7. BD2-AK04/FS...-3 16.6 BD2.-.-800-WB-. 2.00 BD2-AK1/A201.2 BD2-AK04/FS...-4 20.0 BD2.-.-800-SO-. 0.67 BD2-AK1/A202. BD2-AK0/SNH2 12.16 BD2.-.-800-WO-. 0.67 BD2-AK1/A203.8 BD2-AK0/FS...-3 18.6 BD2.-.-1000-SB-. 2.00 BD2-AK1/A203N 6.1 BD2-AK0/FS...-4 22.0 BD2.-.-1000-WB-. 2.00 BD2-AK1/2PC163A162.8 BD2-AK06/SNH3 14.2 BD2.-.-1000-SO-. 0.67 BD2-AK1/3DKS103S14 7.2 BD2-AK04/LS.-DC 17.0 BD2.-.-1000-WO-. 0.67 BD2-AK1/3DKS103A131.9 BD2-AK04/LS.-EC 20.0 BD2.-.-120-SB-. 2.00 BD2-AK1/F1038-3.9 BD2-AK0/LS.-DC 19.0 BD2.-.-120-WB-. 2.00 BD2-AK1/F1038-3-N 6.1 BD2-AK0/LS.-EC 23.0 BD2.-.-120-SO-. 0.67 BD2-AK1/FI40-162. BD2-AK06/LS.-DC 22.0 BD2.-.-120-WO-. 0.67 BD2-AK1/A133.2 BD2-AK06/LS.-EC 26.0 Junction units BD2-AK1/T2-A163 4. Accessories BD2.-400-L.. 1.27 BD2-AK1/3T23-3A161.7 BD2-400-SK 1.64 BD2.-400-Z.. 1.88 BD2-AK.2X/S18 4.8 BD2-400-FE BD2.-1000-L.. 1.27 BD2-AK.2X/S27(/FORMP) 2.94 BD2-400-BB BD2.-1000-Z.. 1.88 BD2-AK.2X/S33(/FORMP) 2.94 BD2-400-HF BD2.-120-L.. 1.27 BD2-AK2X/CEE32S33(/FORMP) 4.7 BD2-400-HFE BD2.-120-Z.. 1.88 BD2-AK.2M2/A323.1 BD2-400-VF BD2.-400-T.. 2.00 BD2-AK2M2/CEE32A323 6.7 BD2-120-EK 2.46 BD2.-400-K.. 2.67 BD2-AK2X/CEE63S33(/FORMP).8 BD2-120-FE BD2.-1000-T.. 2.00 BD2-AK2X/2CEE16S14 7.9 BD2-120-BB BD2.-1000-K.. 2.67 BD2-AK2X/2CEE16S27(/FORMP) 6.1 BD2-120-HF BD2.-120-T.. 2.00 BD2-AK2M2/2SD163CEE16A163 6.9 BD2-120-HFE BD2.-120-K.. 2.67 BD2-AK2M2/2CEE16A163 9.4 BD2-120-VF Feeder units kwh BD2-AK.2M2/A323N.1 BD2-FFE BD2.-20-EE 3.20 BD2-AK.2M2/A633 BD2-FF BD2.-20-VE 3.00 BD2-AK.2M2/A633N.3 BD2-FAS BD2.-400-EE 3.0 BD2-AK2X/3BS133GB131 7.9 BD2-AK...-IP BD2.-400-ME 3.90 BD2-AK2X/3BS133A131.9 BD2-400-FS. BD2.-400-VE 3.20 BD2-AK.2X/GB323 7.6 BD2-120-FS. BD2.-1000-EE 3.80 BD2-AK.2X/GB633 7.9 BD2-SD163 0.1 BD2.-120-EE 4.10 BD2-AK.2X/F141-3(N).9 BD2-CEE163 0.2 BD2.-1000-VE 3.60 BD2-AK.2X/F228-3(N) 6.1 BD2-CEE16 0.2 BD2.-120-VE 4.00 BD2-AK.3X/LSD40-3 9.79 BD2-CEE32 0.3 BD2-1000-ME 8.10 BD2-AK.3X/LSD63-3 9.79 BD2-AG Ancillary equipment units BD2-AK.3X/LSD80-3 9.79 BD2-APO BD2-GKX/F 0.4 BD2-AK.3X/LSD100-3 9.79 BD2-APM BD2-GKM2/F 1. BD2-AK.3X/LSD12-3 9.79 Siemens LV 70 2009 /21
BD2 System 160... 120 A Trunking units Selection and ordering data With aluminum busbars Version Rated current I e Length Tap-off points DT Tap-off point distance 0. m L1, L2, L3, N, 1 / 2 PE Number Distance PS* Weight per unit approx. A m m Type Order No. kg Standard lengths, with tap-off points on both sides With joint block 160 3.2 12 0. X BD2A-2-160-SB-3 BVP:261410 1 unit 20.000 2.2 8 0. X BD2A-2-160-SB-2 BVP:26098 1 unit 14.000 1.2 4 0. X BD2A-2-160-SB-1 BVP:26097 1 unit 8.400 NSV0_0007 20 3.2 12 0. X BD2A-2-20-SB-3 BVP:261413 1 unit 22.200 2.2 8 0. X BD2A-2-20-SB-2 BVP:261412 1 unit 16.00 1.2 4 0. X BD2A-2-20-SB-1 BVP:261411 1 unit 8.600 400 3.2 12 0. X BD2A-2-400-SB-3 BVP:261419 1 unit 26.800 2.2 8 0. X BD2A-2-400-SB-2 BVP:261418 1 unit 19.600 1.2 4 0. X BD2A-2-400-SB-1 BVP:261417 1 unit 12.300 630 3.2 12 0. X BD2A-2-630-SB-3 BVP:261431 1 unit 36.600 2.2 8 0. X BD2A-2-630-SB-2 BVP:261430 1 unit 27.900 1.2 4 0. X BD2A-2-630-SB-1 BVP:261429 1 unit 1.900 800 3.2 12 0. X BD2A-2-800-SB-3 BVP:261437 1 unit 38.400 2.2 8 0. X BD2A-2-800-SB-2 BVP:261436 1 unit 26.00 1.2 4 0. X BD2A-2-800-SB-1 BVP:26143 1 unit 18.00 1000 3.2 12 0. X BD2A-2-1000-SB-3 BVP:261443 1 unit 48.800 2.2 8 0. X BD2A-2-1000-SB-2 BVP:261442 1 unit 33.00 1.2 4 0. X BD2A-2-1000-SB-1 BVP:261441 1 unit 22.400 Standard lengths, without tap-off points With joint block 400 3.2 -- -- X BD2A-2-400-SO-3 BVP:261422 1 unit 26.100 2.2 -- -- X BD2A-2-400-SO-2 BVP:261421 1 unit 19.600 1.2 -- -- X BD2A-2-400-SO-1 BVP:261420 1 unit 12.300 NSV0_0008 630 3.2 -- -- X BD2A-2-630-SO-3 BVP:261434 1 unit 37.600 2.2 -- -- X BD2A-2-630-SO-2 BVP:261433 1 unit 28.900 1.2 -- -- X BD2A-2-630-SO-1 BVP:261432 1 unit 17.200 800 3.2 -- -- X BD2A-2-800-SO-3 BVP:261440 1 unit 39.400 2.2 -- -- X BD2A-2-800-SO-2 BVP:261439 1 unit 27.00 1.2 -- -- X BD2A-2-800-SO-1 BVP:261438 1 unit 19.000 1000 3.2 -- -- X BD2A-2-1000-SO-3 BVP:261446 1 unit 49.800 2.2 -- -- X BD2A-2-1000-SO-2 BVP:26144 1 unit 34.00 1.2 -- -- X BD2A-2-1000-SO-1 BVP:261444 1 unit 22.900 Special colors available on request. Version Type suffix Order No. PS* Weight per unit approx. kg Fire barriers (optional) Fire barrier S90 X +BD2-S90-BX*-M* BVP:93196 1 unit 1.000 Fire barrier S120 X +BD2-S120-BX*-M* BVP:93199 1 unit 1.00 For BX* specify the required dimension in meters from the center of the joint block (end without joint block) to the center of the fire wall or fire ceiling, for -M* specify the wall or ceiling thickness. For the configuration of the fire barriers, see page /94. For approval in Germany: BD2-S90(S120)-ZUL-D fire protection kit see page /69. /22 Siemens LV 70 2009 * You can order this quantity or a multiple thereof.
BD2 System 160... 120 A Trunking units Version Rated current I e Length Tap-off points DT Tap-off point distance 0. m L1, L2, L3, N, PE Number Distance PS* Weight per unit approx. A m m Type Order No. kg Standard lengths, with tap-off points on both sides With joint block 160 3.2 12 0. X BD2A-3-160-SB-3 BVP:261480 1 unit 20.000 2.2 8 0. X BD2A-3-160-SB-2 BVP:261479 1 unit 14.000 1.2 4 0. X BD2A-3-160-SB-1 BVP:261478 1 unit 8.400 NSV0_0007 20 3.2 12 0. X BD2A-3-20-SB-3 BVP:261483 1 unit 22.200 2.2 8 0. X BD2A-3-20-SB-2 BVP:261482 1 unit 16.00 1.2 4 0. X BD2A-3-20-SB-1 BVP:261481 1 unit 8.600 400 3.2 12 0. X BD2A-3-400-SB-3 BVP:261489 1 unit 26.000 2.2 8 0. X BD2A-3-400-SB-2 BVP:261488 1 unit 19.000 1.2 4 0. X BD2A-3-400-SB-1 BVP:261487 1 unit 12.000 630 3.2 12 0. X BD2A-3-630-SB-3 BVP:26101 1 unit 36.600 2.2 8 0. X BD2A-3-630-SB-2 BVP:26100 1 unit 27.900 1.2 4 0. X BD2A-3-630-SB-1 BVP:261499 1 unit 1.900 800 3.2 12 0. X BD2A-3-800-SB-3 BVP:26107 1 unit 39.900 2.2 8 0. X BD2A-3-800-SB-2 BVP:26106 1 unit 27.00 1.2 4 0. X BD2A-3-800-SB-1 BVP:2610 1 unit 19.100 1000 3.2 12 0. X BD2A-3-1000-SB-3 BVP:26113 1 unit 1.000 2.2 8 0. X BD2A-3-1000-SB-2 BVP:26112 1 unit 3.000 1.2 4 0. X BD2A-3-1000-SB-1 BVP:26111 1 unit 23.200 Standard lengths, without tap-off points With joint block 400 3.2 -- -- X BD2A-3-400-SO-3 BVP:261492 1 unit 2.300 2.2 -- -- X BD2A-3-400-SO-2 BVP:261491 1 unit 19.000 1.2 -- -- X BD2A-3-400-SO-1 BVP:261490 1 unit 12.000 NSV0_0008 630 3.2 -- -- X BD2A-3-630-SO-3 BVP:26104 1 unit 37.600 2.2 -- -- X BD2A-3-630-SO-2 BVP:26103 1 unit 28.900 1.2 -- -- X BD2A-3-630-SO-1 BVP:26102 1 unit 17.200 800 3.2 -- -- X BD2A-3-800-SO-3 BVP:26110 1 unit 40.900 2.2 -- -- X BD2A-3-800-SO-2 BVP:26109 1 unit 28.00 1.2 -- -- X BD2A-3-800-SO-1 BVP:26108 1 unit 19.600 1000 3.2 -- -- X BD2A-3-1000-SO-3 BVP:26116 1 unit 2.000 2.2 -- -- X BD2A-3-1000-SO-2 BVP:2611 1 unit 36.000 1.2 -- -- X BD2A-3-1000-SO-1 BVP:26114 1 unit 23.700 * You can order this quantity or a multiple thereof. Siemens LV 70 2009 /23
BD2 System 160... 120 A Trunking units With aluminum busbars Version Rated current PS* Weight I e Length Tap-off points DT Tap-off point distance 0. m L1, L2, L3, N, 1 / 2 PE per unit Number Distance approx. A m m Type Order No. kg Optional lengths, with tap-off points on both sides With joint block 160 2.26... 3.24 8... 12 0. X BD2A-2-160-WB-3W* BVP:261447 1 unit 20.000 1.26... 2.24 4... 8 0. X BD2A-2-160-WB-2W* BVP:261448 1 unit 1.000 20 2.26... 3.24 8... 12 0. X BD2A-2-20-WB-3W* BVP:261449 1 unit 21.900 NSV0_0007 1.26... 2.24 4... 8 0. X BD2A-2-20-WB-2W* BVP:26140 1 unit 16.300 400 2.26... 3.24 8... 12 0. X BD2A-2-400-WB-3W* BVP:26143 1 unit 26.100 1.26... 2.24 4... 8 0. X BD2A-2-400-WB-2W* BVP:26144 1 unit 19.100 630 2.26... 3.24 8... 12 0. X BD2A-2-630-WB-3W* BVP:26147 1 unit 4.600 1.26... 2.24 4... 8 0. X BD2A-2-630-WB-2W* BVP:26148 1 unit 30.900 800 2.26... 3.24 8... 12 0. X BD2A-2-800-WB-3W* BVP:26149 1 unit 44.400 1.26... 2.24 4... 8 0. X BD2A-2-800-WB-2W* BVP:261460 1 unit 30.00 1000 2.26... 3.24 8... 12 0. X BD2A-2-1000-WB-3W* BVP:261461 1 unit 4.800 1.26... 2.24 4... 8 0. X BD2A-2-1000-WB-2W* BVP:261462 1 unit 37.00 Optional lengths, without tap-off points With joint block 400 2.26... 3.24 -- -- X BD2A-2-400-WO-3W* BVP:261463 1 unit 26.100 1.26... 2.24 -- -- X BD2A-2-400-WO-2W* BVP:261464 1 unit 19.100 0.0... 1.24 -- -- X BD2A-2-400-WO-1W* BVP:26146 1 unit 11.900 NSV0_0008 630 2.26... 3.24 -- -- X BD2A-2-630-WO-3W* BVP:261469 1 unit 4.600 1.26... 2.24 -- -- X BD2A-2-630-WO-2W* BVP:261470 1 unit 30.900 0.0... 1.24 -- -- X BD2A-2-630-WO-1W* BVP:261471 1 unit 18.200 800 2.26... 3.24 -- -- X BD2A-2-800-WO-3W* BVP:261472 1 unit 44.400 1.26... 2.24 -- -- X BD2A-2-800-WO-2W* BVP:261473 1 unit 30.00 0.0... 1.24 -- -- X BD2A-2-800-WO-1W* BVP:261474 1 unit 19.300 1000 2.26... 3.24 -- -- X BD2A-2-1000-WO-3W* BVP:26147 1 unit 4.800 1.26... 2.24 -- -- X BD2A-2-1000-WO-2W* BVP:261476 1 unit 37.00 0.0... 1.24 -- -- X BD2A-2-1000-WO-1W* BVP:261477 1 unit 23.200 For W*, you must specify the required dimension in meters between the center of one joint block to the center of the next, e.g. -3W2.0. For optional lengths, see page /81. Special colors available on request. Version Type suffix Order No. PS* Weight per unit approx. kg Fire barriers (optional) Fire barrier S90 X +BD2-S90-BX*-M* BVP:93196 1 unit 1.000 Fire barrier S120 X +BD2-S120-BX*-M* BVP:93199 1 unit 1.00 For BX* specify the required dimension in meters from the center of the joint block (end without joint block) to the center of the fire wall or fire ceiling, for -M* specify the wall or ceiling thickness. For the configuration of the fire barriers, see page /94. For approval in Germany: BD2-S90(S120)-ZUL-D fire protection kit see page /69. /24 Siemens LV 70 2009 * You can order this quantity or a multiple thereof.
BD2 System 160... 120 A Trunking units Version Rated current I e Length Tap-off points DT Tap-off point distance 0. m L1, L2, L3, N, PE Number Distance PS* Weight per unit approx. A m m Type Order No. kg Optional lengths, with tap-off points on both sides With joint block 160 2.26... 3.24 8... 12 0. X BD2A-3-160-WB-3W* BVP:26117 1 unit 20.000 1.26... 2.24 4... 8 0. X BD2A-3-160-WB-2W* BVP:26118 1 unit 1.000 20 2.26... 3.24 8... 12 0. X BD2A-3-20-WB-3W* BVP:26119 1 unit 21.900 NSV0_0007 1.26... 2.24 4... 8 0. X BD2A-3-20-WB-2W* BVP:26120 1 unit 16.300 400 2.26... 3.24 8... 12 0. X BD2A-3-400-WB-3W* BVP:26123 1 unit 2.300 1.26... 2.24 4... 8 0. X BD2A-3-400-WB-2W* BVP:26124 1 unit 18.00 630 2.26... 3.24 8... 12 0. X BD2A-3-630-WB-3W* BVP:26127 1 unit 4.600 1.26... 2.24 4... 8 0. X BD2A-3-630-WB-2W* BVP:26128 1 unit 30.900 800 2.26... 3.24 8... 12 0. X BD2A-3-800-WB-3W* BVP:26129 1 unit 4.900 1.26... 2.24 4... 8 0. X BD2A-3-800-WB-2W* BVP:26130 1 unit 31.00 1000 2.26... 3.24 8... 12 0. X BD2A-3-1000-WB-3W* BVP:26131 1 unit 7.000 1.26... 2.24 4... 8 0. X BD2A-3-1000-WB-2W* BVP:26132 1 unit 39.000 Optional lengths, without tap-off points With joint block 400 2.26... 3.24 -- -- X BD2A-3-400-WO-3W* BVP:26133 1 unit 2.300 1.26... 2.24 -- -- X BD2A-3-400-WO-2W* BVP:26134 1 unit 18.00 0.0... 1.24 -- -- X BD2A-3-400-WO-1W* BVP:2613 1 unit 11.600 NSV0_0008 630 2.26... 3.24 -- -- X BD2A-3-630-WO-3W* BVP:26139 1 unit 4.600 1.26... 2.24 -- -- X BD2A-3-630-WO-2W* BVP:26140 1 unit 30.900 0.0... 1.24 -- -- X BD2A-3-630-WO-1W* BVP:26141 1 unit 18.200 800 2.26... 3.24 -- -- X BD2A-3-800-WO-3W* BVP:26142 1 unit 4.900 1.26... 2.24 -- -- X BD2A-3-800-WO-2W* BVP:26143 1 unit 31.00 0.0... 1.24 -- -- X BD2A-3-800-WO-1W* BVP:26144 1 unit 19.900 1000 2.26... 3.24 -- -- X BD2A-3-1000-WO-3W* BVP:2614 1 unit 7.000 1.26... 2.24 -- -- X BD2A-3-1000-WO-2W* BVP:26146 1 unit 39.000 0.0... 1.24 -- -- X BD2A-3-1000-WO-1W* BVP:26147 1 unit 24.000 * You can order this quantity or a multiple thereof. Siemens LV 70 2009 /2
BD2 System 160... 120 A Trunking units With copper busbars Version Special colors available on request. For BX* specify the required dimension in meters from the center of the joint block (end without joint block) to the center of the fire wall or fire ceiling, for -M* specify the wall or ceiling thickness. For the configuration of the fire barriers, see page /94. For approval in Germany: BD2-S90(S120)-ZUL-D fire protection kit see page /69. Rated current I e Length Tap-off points DT Tap-off point distance 0. m L1, L2, L3, N, 1 / 2 PE Number Distance PS* Weight per unit approx. A m m Type Order No. kg Standard lengths, with tap-off points on both sides With joint block 160 3.2 12 0. X BD2C-2-160-SB-3 BVP:261631 1 unit 26.400 2.2 8 0. X BD2C-2-160-SB-2 BVP:261630 1 unit 18.400 1.2 4 0. X BD2C-2-160-SB-1 BVP:261629 1 unit 10.800 NSV0_0007 20 3.2 12 0. X BD2C-2-20-SB-3 BVP:261634 1 unit 27.00 2.2 8 0. X BD2C-2-20-SB-2 BVP:261633 1 unit 20.100 1.2 4 0. X BD2C-2-20-SB-1 BVP:261632 1 unit 10.600 400 3.2 12 0. X BD2C-2-400-SB-3 BVP:261640 1 unit 33.200 2.2 8 0. X BD2C-2-400-SB-2 BVP:261639 1 unit 23.900 1.2 4 0. X BD2C-2-400-SB-1 BVP:261638 1 unit 14.700 630 3.2 12 0. X BD2C-2-630-SB-3 BVP:26162 1 unit 47.300 2.2 8 0. X BD2C-2-630-SB-2 BVP:26161 1 unit 3.300 1.2 4 0. X BD2C-2-630-SB-1 BVP:26160 1 unit 19.900 800 3.2 12 0. X BD2C-2-800-SB-3 BVP:26168 1 unit 7.400 2.2 8 0. X BD2C-2-800-SB-2 BVP:26167 1 unit 39.00 1.2 4 0. X BD2C-2-800-SB-1 BVP:26166 1 unit 2.600 1000 3.2 12 0. X BD2C-2-1000-SB-3 BVP:261664 1 unit 76.800 2.2 8 0. X BD2C-2-1000-SB-2 BVP:261663 1 unit 2.800 1.2 4 0. X BD2C-2-1000-SB-1 BVP:261662 1 unit 32.900 120 3.2 12 0. X BD2C-2-120-SB-3 BVP:261670 1 unit 112.900 2.2 8 0. X BD2C-2-120-SB-2 BVP:261669 1 unit 77.600 1.2 4 0. X BD2C-2-120-SB-1 BVP:261668 1 unit 46.400 Standard lengths, without tap-off points With joint block 400 3.2 -- -- X BD2C-2-400-SO-3 BVP:261643 1 unit 32.00 2.2 -- -- X BD2C-2-400-SO-2 BVP:261642 1 unit 23.900 1.2 -- -- X BD2C-2-400-SO-1 BVP:261641 1 unit 14.700 NSV0_0008 630 3.2 -- -- X BD2C-2-630-SO-3 BVP:2616 1 unit 48.300 2.2 -- -- X BD2C-2-630-SO-2 BVP:26164 1 unit 36.300 1.2 -- -- X BD2C-2-630-SO-1 BVP:26163 1 unit 21.200 800 3.2 -- -- X BD2C-2-800-SO-3 BVP:261661 1 unit 8.400 2.2 -- -- X BD2C-2-800-SO-2 BVP:261660 1 unit 40.00 1.2 -- -- X BD2C-2-800-SO-1 BVP:26169 1 unit 26.100 1000 3.2 -- -- X BD2C-2-1000-SO-3 BVP:261667 1 unit 77.800 2.2 -- -- X BD2C-2-1000-SO-2 BVP:261666 1 unit 3.800 1.2 -- -- X BD2C-2-1000-SO-1 BVP:26166 1 unit 33.400 120 3.2 -- -- X BD2C-2-120-SO-3 BVP:261673 1 unit 113.900 2.2 -- -- X BD2C-2-120-SO-2 BVP:261672 1 unit 78.600 1.2 -- -- X BD2C-2-120-SO-1 BVP:261671 1 unit 46.900 Version Type suffix Order No. PS* Weight per unit approx. kg Fire barriers (optional) Fire barrier S120 X +BD2-S120-BX*-M* BVP:93199 1 unit 1.00 /26 Siemens LV 70 2009 * You can order this quantity or a multiple thereof.
BD2 System 160... 120 A Trunking units With copper busbars Version Rated current I e Length Tap-off points DT Tap-off point distance 0. m L1, L2, L3, N, PE Number Distance PS* Weight per unit approx. A m m Type Order No. kg Standard lengths, with tap-off points on both sides With joint block 160 3.2 12 0. X BD2C-3-160-SB-3 BVP:261712 1 unit 26.400 2.2 8 0. X BD2C-3-160-SB-2 BVP:261711 1 unit 18.400 1.2 4 0. X BD2C-3-160-SB-1 BVP:261710 1 unit 10.800 NSV0_0007 20 3.2 12 0. X BD2C-3-20-SB-3 BVP:26171 1 unit 27.00 2.2 8 0. X BD2C-3-20-SB-2 BVP:261714 1 unit 20.100 1.2 4 0. X BD2C-3-20-SB-1 BVP:261713 1 unit 10.600 400 3.2 12 0. X BD2C-3-400-SB-3 BVP:261721 1 unit 34.400 2.2 8 0. X BD2C-3-400-SB-2 BVP:261720 1 unit 24.700 1.2 4 0. X BD2C-3-400-SB-1 BVP:261719 1 unit 1.100 630 3.2 12 0. X BD2C-3-630-SB-3 BVP:261733 1 unit 47.300 2.2 8 0. X BD2C-3-630-SB-2 BVP:261732 1 unit 3.300 1.2 4 0. X BD2C-3-630-SB-1 BVP:261731 1 unit 19.900 800 3.2 12 0. X BD2C-3-800-SB-3 BVP:261739 1 unit 60.800 2.2 8 0. X BD2C-3-800-SB-2 BVP:261738 1 unit 41.900 1.2 4 0. X BD2C-3-800-SB-1 BVP:261737 1 unit 26.900 1000 3.2 12 0. X BD2C-3-1000-SB-3 BVP:26174 1 unit 80.700 2.2 8 0. X BD2C-3-1000-SB-2 BVP:261744 1 unit.00 1.2 4 0. X BD2C-3-1000-SB-1 BVP:261743 1 unit 34.400 120 3.2 12 0. X BD2C-3-120-SB-3 BVP:26171 1 unit 120.900 2.2 8 0. X BD2C-3-120-SB-2 BVP:26170 1 unit 83.100 1.2 4 0. X BD2C-3-120-SB-1 BVP:261749 1 unit 49.400 Standard lengths, without tap-off points With joint block 400 3.2 -- -- X BD2C-3-400-SO-3 BVP:261724 1 unit 33.700 2.2 -- -- X BD2C-3-400-SO-2 BVP:261723 1 unit 24.700 1.2 -- -- X BD2C-3-400-SO-1 BVP:261722 1 unit 1.100 NSV0_0008 630 3.2 -- -- X BD2C-3-630-SO-3 BVP:261736 1 unit 48.300 2.2 -- -- X BD2C-3-630-SO-2 BVP:26173 1 unit 36.300 1.2 -- -- X BD2C-3-630-SO-1 BVP:261734 1 unit 21.200 800 3.2 -- -- X BD2C-3-800-SO-3 BVP:261742 1 unit 61.800 2.2 -- -- X BD2C-3-800-SO-2 BVP:261741 1 unit 42.900 1.2 -- -- X BD2C-3-800-SO-1 BVP:261740 1 unit 27.400 1000 3.2 -- -- X BD2C-3-1000-SO-3 BVP:261748 1 unit 81.700 2.2 -- -- X BD2C-3-1000-SO-2 BVP:261747 1 unit 6.00 1.2 -- -- X BD2C-3-1000-SO-1 BVP:261746 1 unit 34.900 120 3.2 -- -- X BD2C-3-120-SO-3 BVP:26174 1 unit 121.900 2.2 -- -- X BD2C-3-120-SO-2 BVP:26173 1 unit 84.100 1.2 -- -- X BD2C-3-120-SO-1 BVP:26172 1 unit 49.900 * You can order this quantity or a multiple thereof. Siemens LV 70 2009 /27
BD2 System 160... 120 A Trunking units With copper busbars Version Rated current PS* Weight I e Length Tap-off points DT Tap-off point distance 0. m L1, L2, L3, N, 1 / 2 PE per unit Number Distance approx. A m m Type Order No. kg Optional lengths, with tap-off points on both sides With joint block 160 2.26... 3.24 8... 12 0. X BD2C-2-160-WB-3W* BVP:261674 1 unit 26.400 1.26... 2.24 4... 8 0. X BD2C-2-160-WB-2W* BVP:26167 1 unit 19.400 20 2.26... 3.24 8... 12 0. X BD2C-2-20-WB-3W* BVP:261676 1 unit 27.200 NSV0_0007 1.26... 2.24 4... 8 0. X BD2C-2-20-WB-2W* BVP:261677 1 unit 19.900 400 2.26... 3.24 8... 12 0. X BD2C-2-400-WB-3W* BVP:261680 1 unit 32.00 1.26... 2.24 4... 8 0. X BD2C-2-400-WB-2W* BVP:261681 1 unit 23.400 630 2.26... 3.24 8... 12 0. X BD2C-2-630-WB-3W* BVP:261684 1 unit 6.300 1.26... 2.24 4... 8 0. X BD2C-2-630-WB-2W* BVP:26168 1 unit 38.300 800 2.26... 3.24 8... 12 0. X BD2C-2-800-WB-3W* BVP:261686 1 unit 63.400 1.26... 2.24 4... 8 0. X BD2C-2-800-WB-2W* BVP:261687 1 unit 43.00 1000 2.26... 3.24 8... 12 0. X BD2C-2-1000-WB-3W* BVP:261688 1 unit 82.800 1.26... 2.24 4... 8 0. X BD2C-2-1000-WB-2W* BVP:261689 1 unit 6.800 120 2.26... 3.24 8... 12 0. X BD2C-2-120-WB-3W* BVP:261690 1 unit 118.900 1.26... 2.24 4... 8 0. X BD2C-2-120-WB-2W* BVP:261691 1 unit 81.600 Optional lengths, without tap-off points With joint block 400 2.26... 3.24 -- -- X BD2C-2-400-WO-3W* BVP:261692 1 unit 32.00 1.26... 2.24 -- -- X BD2C-2-400-WO-2W* BVP:261693 1 unit 23.400 0.0... 1.24 -- -- X BD2C-2-400-WO-1W* BVP:261694 1 unit 14.300 NSV0_0008 630 2.26... 3.24 -- -- X BD2C-2-630-WO-3W* BVP:261698 1 unit 6.300 1.26... 2.24 -- -- X BD2C-2-630-WO-2W* BVP:261699 1 unit 38.300 0.0... 1.24 -- -- X BD2C-2-630-WO-1W* BVP:261700 1 unit 22.200 800 2.26... 3.24 -- -- X BD2C-2-800-WO-3W* BVP:261701 1 unit 63.400 1.26... 2.24 -- -- X BD2C-2-800-WO-2W* BVP:261702 1 unit 43.00 0.0... 1.24 -- -- X BD2C-2-800-WO-1W* BVP:261703 1 unit 26.400 1000 2.26... 3.24 -- -- X BD2C-2-1000-WO-3W* BVP:261704 1 unit 82.800 1.26... 2.24 -- -- X BD2C-2-1000-WO-2W* BVP:26170 1 unit 6.800 0.0... 1.24 -- -- X BD2C-2-1000-WO-1W* BVP:261706 1 unit 33.700 120 2.26... 3.24 -- -- X BD2C-2-120-WO-3W* BVP:261707 1 unit 118.900 1.26... 2.24 -- -- X BD2C-2-120-WO-2W* BVP:261708 1 unit 81.600 0.0... 1.24 -- -- X BD2C-2-120-WO-1W* BVP:261709 1 unit 47.200 For W*, you must specify the required dimension in meters between the center of one joint block to the center of the next, e.g. -3W2.0. For optional lengths, see page /81. Special colors available on request. Version Type suffix Order No. PS* Weight per unit approx. kg Fire barriers (optional) Fire barrier S120 X +BD2-S120-BX*-M* BVP:93199 1 unit 1.00 For BX* specify the required dimension in meters from the center of the joint block (end without joint block) to the center of the fire wall or fire ceiling, for -M* specify the wall or ceiling thickness. For the configuration of the fire barriers, see page /94. For approval in Germany: BD2-S90(S120)-ZUL-D fire protection kit see page /69. /28 Siemens LV 70 2009 * You can order this quantity or a multiple thereof.
BD2 System 160... 120 A Trunking units With copper busbars Version Rated current I e Length Tap-off points DT Tap-off point distance 0. m L1, L2, L3, N, PE Number Distance PS* Weight per unit approx. A m m Type Order No. kg Optional lengths, with tap-off points on both sides With joint block 160 2.26... 3.24 8... 12 0. X BD2C-3-160-WB-3W* BVP:2617 1 unit 26.400 1.26... 2.24 4... 8 0. X BD2C-3-160-WB-2W* BVP:26176 1 unit 19.400 20 2.26... 3.24 8... 12 0. X BD2C-3-20-WB-3W* BVP:26177 1 unit 27.200 NSV0_0007 1.26... 2.24 4... 8 0. X BD2C-3-20-WB-2W* BVP:26178 1 unit 19.900 400 2.26... 3.24 8... 12 0. X BD2C-3-400-WB-3W* BVP:261761 1 unit 33.700 1.26... 2.24 4... 8 0. X BD2C-3-400-WB-2W* BVP:261762 1 unit 24.200 630 2.26... 3.24 8... 12 0. X BD2C-3-630-WB-3W* BVP:26176 1 unit 6.300 1.26... 2.24 4... 8 0. X BD2C-3-630-WB-2W* BVP:261766 1 unit 38.300 800 2.26... 3.24 8... 12 0. X BD2C-3-800-WB-3W* BVP:261767 1 unit 66.800 1.26... 2.24 4... 8 0. X BD2C-3-800-WB-2W* BVP:261768 1 unit 4.900 1000 2.26... 3.24 8... 12 0. X BD2C-3-1000-WB-3W* BVP:261769 1 unit 86.700 1.26... 2.24 4... 8 0. X BD2C-3-1000-WB-2W* BVP:261770 1 unit 9.00 120 2.26... 3.24 8... 12 0. X BD2C-3-120-WB-3W* BVP:261771 1 unit 126.900 1.26... 2.24 4... 8 0. X BD2C-3-120-WB-2W* BVP:261772 1 unit 87.100 Optional lengths, without tap-off points With joint block 400 2.26... 3.24 -- -- X BD2C-3-400-WO-3W* BVP:261773 1 unit 33.700 1.26... 2.24 -- -- X BD2C-3-400-WO-2W* BVP:261774 1 unit 24.200 0.0... 1.24 -- -- X BD2C-3-400-WO-1W* BVP:26177 1 unit 14.700 NSV0_0008 630 2.26... 3.24 -- -- X BD2C-3-630-WO-3W* BVP:261779 1 unit 6.300 1.26... 2.24 -- -- X BD2C-3-630-WO-2W* BVP:261780 1 unit 38.300 0.0... 1.24 -- -- X BD2C-3-630-WO-1W* BVP:261781 1 unit 22.200 800 2.26... 3.24 -- -- X BD2C-3-800-WO-3W* BVP:261782 1 unit 66.800 1.26... 2.24 -- -- X BD2C-3-800-WO-2W* BVP:261783 1 unit 4.900 0.0... 1.24 -- -- X BD2C-3-800-WO-1W* BVP:261784 1 unit 27.700 1000 2.26... 3.24 -- -- X BD2C-3-1000-WO-3W* BVP:26178 1 unit 86.700 1.26... 2.24 -- -- X BD2C-3-1000-WO-2W* BVP:261786 1 unit 9.00 0.0... 1.24 -- -- X BD2C-3-1000-WO-1W* BVP:261787 1 unit 34.900 120 2.26... 3.24 -- -- X BD2C-3-120-WO-3W* BVP:261788 1 unit 126.900 1.26... 2.24 -- -- X BD2C-3-120-WO-2W* BVP:261789 1 unit 87.100 0.0... 1.24 -- -- X BD2C-3-120-WO-1W* BVP:261790 1 unit 0.200 * You can order this quantity or a multiple thereof. Siemens LV 70 2009 /29
BD2 System 160... 120 A Junction units Selection and ordering data With aluminum busbars Version L-units (with joint block) (fitted to Y as standard) Knee, rear Y X NSV0_00428 Length/ Optional length X0.36/ Y0.36 X0.36... 1.2/ Y0.36 X0.36/ Y0.36... 1.2 X0.36... 1.2/ Y0.36... 1.2 DT Rated current I e 160 A, 20 A, 400 A PS* Type Order No. kg Weight per unit approx. X BD2A-400-LH BVP:261793 1 unit 8.00 X BD2A-400-LH-X* BVP:261846 1 unit 18.000 X BD2A-400-LH-Y* BVP:261847 1 unit 18.000 X BD2A-400-LH-X*/Y* BVP:261848 1 unit 28.000 Knee, front Y X NSV0_00429 X0.36/ Y0.36 X0.36... 1.2/ Y0.36 X0.36/ Y0.36... 1.2 X0.36... 1.2/ Y0.36... 1.2 X BD2A-400-LV BVP:261796 1 unit 8.00 X BD2A-400-LV-X* BVP:261849 1 unit 18.000 X BD2A-400-LV-Y* BVP:26180 1 unit 18.000 X BD2A-400-LV-X*/Y* BVP:26181 1 unit 28.000 Elbow, right X0.36/ X BD2A-400-LR BVP:26179 1 unit 8.000 Y0.36 X0.36... 1.2/ X BD2A-400-LR-X* BVP:26182 1 unit 18.000 Y0.36 X0.36/ X BD2A-400-LR-Y* BVP:26183 1 unit 18.000 Y0.36... 1.2 X0.36... 1.2/ X BD2A-400-LR-X*/Y* BVP:26184 1 unit 28.000 Y0.36... 1.2 Elbow, left X0.36/ X BD2A-400-LL BVP:261794 1 unit 8.000 Y0.36 X0.36... 1.2/ X BD2A-400-LL-X* BVP:2618 1 unit 18.000 Y0.36 X0.36/ X BD2A-400-LL-Y* BVP:26186 1 unit 18.000 Y0.36... 1.2 X0.36... 1.2/ X BD2A-400-LL-X*/Y* BVP:26187 1 unit 28.000 Y0.36... 1.2 Optional lengths: For X* and Y* you must specify the required dimension in meters from the center of the joint block to the outside edge of the trunking unit (see also page /81). Special colors available on request. Y Y X NSV0_00430 X NSV0_00431 Version Type suffix Order No. PS* Weight per unit approx. kg Fire barriers for L-units (optional) Fire barrier S90 in limb X X +BD2-S90-BX*-M* BVP:93196 1 unit 1.000 Fire barrier S90 in limb Y X +BD2-S90-BY*-M* BVP:93197 1 unit 1.000 Fire barrier S120 in limb X X +BD2-S120-BX*-M* BVP:93199 1 unit 1.00 Fire barrier S120 in limb Y X +BD2-S120-BY*-M* BVP:931960 1 unit 1.00 For BX* or BY you must specify the required dimension in meters For the configuration of the fire barriers, see page /94. from the center of the joint block (for BX*: end without joint block) to the center of the fire wall or fire ceiling, for -M* specify the wall For approval in Germany: or ceiling thickness. BD2-S90(S120)-ZUL-D fire protection kit see page /69. /30 Siemens LV 70 2009 * You can order this quantity or a multiple thereof.
BD2 System 160... 120 A Junction units With aluminum busbars Version L-units (with joint block) (Fitted to Y as standard) Knee, rear Y X NSV0_00428 Length/ Optional length X0.36/ Y0.36 X0.36... 1.2/ Y0.36 X0.36/ Y0.36... 1.2 X0.36... 1.2/ Y0.36... 1.2 DT Rated current I e 630 A, 800 A, 1000 A PS* Type Order kg Weight per unit approx. X BD2A-1000-LH BVP:261803 1 unit 17.000 X BD2A-1000-LH-X* BVP:261874 1 unit 38.000 X BD2A-1000-LH-Y* BVP:26187 1 unit 38.000 X BD2A-1000-LH-X*/Y* BVP:261876 1 unit 9.000 Knee, front Y X NSV0_00429 X0.36/ Y0.36 X0.36... 1.2/ Y0.36 X0.36/ Y0.36... 1.2 X0.36... 1.2/ Y0.36... 1.2 X BD2A-1000-LV BVP:261806 1 unit 17.000 X BD2A-1000-LV-X* BVP:261877 1 unit 38.000 X BD2A-1000-LV-Y* BVP:261878 1 unit 38.000 X BD2A-1000-LV-X*/Y* BVP:261879 1 unit 9.000 Elbow, right Elbow, left Y Y X NSV0_00430 X NSV0_00431 X0.36/ Y0.36 X0.36... 1.2/ Y0.36 X0.36/ Y0.36... 1.2 X0.36... 1.2/ Y0.36... 1.2 X0.36/ Y0.36 X0.36... 1.2/ Y0.36 X0.36/ Y0.36... 1.2 X0.36... 1.2/ Y0.36... 1.2 Optional lengths: For X* and Y* you must specify the required dimension in meters from the center of the joint block to the outside edge of the trunking unit (see also page /81). Special colors available on request. X BD2A-1000-LR BVP:26180 1 unit 17.000 X BD2A-1000-LR-X* BVP:261880 1 unit 38.000 X BD2A-1000-LR-Y* BVP:261881 1 unit 38.000 X BD2A-1000-LR-X*/Y* BVP:261882 1 unit 9.000 X BD2A-1000-LL BVP:261804 1 unit 17.000 X BD2A-1000-LL-X* BVP:261827 1 unit 38.000 X BD2A-1000-LL-Y* BVP:261828 1 unit 38.000 X BD2A-1000-LL-X*/Y* BVP:261829 1 unit 9.000 * You can order this quantity or a multiple thereof. Siemens LV 70 2009 /31
BD2 System 160... 120 A Junction units With aluminum busbars Version Z-units (with joint block) (Fitted to Y as standard) Rear Z NSV0_00432 X Length/ Optional length X0.36/ Y0.36/ Z0.14... 1.2 X0.36... 0.60/ Y0.36... 0.60/ Z0.14... 1.2 DT Rated current I e 160 A, 20 A, 400 A PS* Type Order No. kg Weight per unit approx. X BD2A-400-ZH-Z* BVP:261814 1 unit 13.000 X BD2A-400-ZH-X*/Y*/Z* BVP:261822 1 unit 16.000 Y Front Y Z X0.36/ Y0.36/ Z0.14... 1.2 X0.36... 0.60/ Y0.36... 0.60/ Z0.14... 1.2 X BD2A-400-ZV-Z* BVP:261813 1 unit 13.000 X BD2A-400-ZV-X*/Y*/Z* BVP:261821 1 unit 16.000 NSV0_00433 X Right Y Z X NSV0_00434 X0.36/ Y0.36/ Z0.34... 1.2 X0.36... 0.60/ Y0.36... 0.60/ Z0.34... 1.2 X BD2A-400-ZR-Z* BVP:261811 1 unit 13.000 X BD2A-400-ZR-X*/Y*/Z* BVP:261819 1 unit 16.000 Left Y Z NSV0_0043 X X0.36/ Y0.36/ Z0.34... 1.2 X0.36... 0.60/ Y0.36... 0.60/ Z0.34... 1.2 X BD2A-400-ZL-Z* BVP:261812 1 unit 13.000 X BD2A-400-ZL-X*/Y*/Z* BVP:261820 1 unit 16.000 Optional lengths: For X* and Y* you must specify the required dimension in meters from the center of the joint block to the outside edge of the trunking unit, for Z* from the outer edge to the outer edge of the trunking unit (see also page /81). Special colors available on request. /32 Siemens LV 70 2009 * You can order this quantity or a multiple thereof.
BD2 System 160... 120 A Junction units With aluminum busbars Version Z-units (with joint block) (Fitted to Y as standard) Rear Z NSV0_00432 X Length/ Optional length X0.36/ Y0.36/ Z0.26... 1.2 X0.36... 0.60/ Y0.36... 0.60/ Z0.26... 1.2 DT Rated current I e 630 A, 800 A, 1000 A PS* Type Order No. kg Weight per unit approx. X BD2A-1000-ZH-Z* BVP:261818 1 unit 26.000 X BD2A-1000-ZH-X*/Y*/Z* BVP:261826 1 unit 32.000 Y Front Y Z X0.36/ Y0.36/ Z0.26... 1.2 X0.36... 0.60/ Y0.36... 0.60/ Z0.26... 1.2 X BD2A-1000-ZV-Z* BVP:261817 1 unit 26.000 X BD2A-1000-ZV-X*/Y*/Z* BVP:26182 1 unit 32.000 NSV0_00433 X Right Y Z X NSV0_00434 X0.36/ Y0.36/ Z0.34... 1.2 X0.36... 0.60/ Y0.36... 0.60/ Z0.34... 1.2 X BD2A-1000-ZR-Z* BVP:26181 1 unit 26.000 X BD2A-1000-ZR-X*/Y*/Z* BVP:261823 1 unit 32.000 Left Y Z NSV0_0043 X X0.36/ Y0.36/ Z0.34... 1.2 X0.36... 0.60/ Y0.36... 0.60/ Z0.34... 1.2 X BD2A-1000-ZL-Z* BVP:261816 1 unit 26.000 X BD2A-1000-ZL-X*/Y*/Z* BVP:261824 1 unit 32.000 Optional lengths: For X* and Y* you must specify the required dimension in meters from the center of the joint block to the outside edge of the trunking unit, for Z* from the outer edge to the outer edge of the trunking unit (see also page /81). Special colors available on request. * You can order this quantity or a multiple thereof. Siemens LV 70 2009 /33
BD2 System 160... 120 A Junction units With aluminum busbars Version Length/ Optional length L-units (with joint block), with engineered angle 8... 17 (Fitted to Y as standard) Knee, rear X0.36/ Y0.36 X0.36... 1.2/ Y0.36 X0.36/ Y Y0.36... 1.2 8 7 X0.36... 1.2/ Y0.36... 1.2 X NSV0_00436 DT Rated current I e 160 A, 20 A, 400 A PS* Type Order No. kg Weight per unit approx. X BD2A-400-LH-G* BVP:26188 1 unit 8.000 X BD2A-400-LH-X*-G* BVP:26189 1 unit 18.000 X BD2A-400-LH-Y*-G* BVP:261860 1 unit 18.000 X BD2A-400-LH-X*/Y*-G* BVP:261861 1 unit 28.000 Knee, front 8 17 Y X NSV0_00437 X0.36/ Y0.36 X0.36... 1.2/ Y0.36 X0.36/ Y0.36... 1.2 X0.36... 1.2/ Y0.36... 1.2 X BD2A-400-LV-G* BVP:261862 1 unit 8.000 X BD2A-400-LV-X*-G* BVP:261863 1 unit 18.000 X BD2A-400-LV-Y*-G* BVP:261864 1 unit 18.000 X BD2A-400-LV-X*/Y*-G* BVP:26186 1 unit 28.000 Elbow, right Y Elbow, left Y X 8 17 NSV0_00438 X 8-17 NSV0_00439 X0.36/ Y0.36 X0.36... 1.2/ Y0.36 X0.36/ Y0.36... 1.2 X0.36... 1.2/ Y0.36... 1.2 X0.36/ Y0.36 X0.36... 1.2/ Y0.36 X0.36/ Y0.36... 1.2 X0.36... 1.2/ Y0.36... 1.2 Elbow: For G* you must specify the required number of degrees in increments. Optional lengths: For X* and Y* you must specify the required dimension in meters from the center of the joint block to the outside edge of the trunking unit (see also page /81). Special colors available on request. X BD2A-400-LR-G* BVP:261866 1 unit 8.000 X BD2A-400-LR-X*-G* BVP:261867 1 unit 18.000 X BD2A-400-LR-Y*-G* BVP:261868 1 unit 18.000 X BD2A-400-LR-X*/Y*-G* BVP:261869 1 unit 28.000 X BD2A-400-LL-G* BVP:261870 1 unit 8.000 X BD2A-400-LL-X*-G* BVP:261871 1 unit 18.000 X BD2A-400-LL-Y*-G* BVP:261872 1 unit 18.000 X BD2A-400-LL-X*/Y*-G* BVP:261873 1 unit 28.000 Version Type suffix Order No. PS* Weight per unit approx. kg Fire barriers for L-units (optional) Fire barrier S90 in limb X X +BD2-S90-BX*-M* BVP:93196 1 unit 1.000 Fire barrier S90 in limb Y X +BD2-S90-BY*-M* BVP:93197 1 unit 1.000 Fire barrier S120 in limb X X +BD2-S120-BX*-M* BVP:93199 1 unit 1.00 Fire barrier S120 in limb Y X +BD2-S120-BY*-M* BVP:931960 1 unit 1.00 For BX* or BY you must specify the required dimension in meters For the configuration of the fire barriers, see page /94. from the center of the joint block (for BX*: end without joint block) to the center of the fire wall or fire ceiling, for -M* specify the wall For approval in Germany: or ceiling thickness. BD2-S90(S120)-ZUL-D fire protection kit see page /69. /34 Siemens LV 70 2009 * You can order this quantity or a multiple thereof.
BD2 System 160... 120 A Junction units With aluminum busbars Version Length/ Optional length L-units (with joint block), with engineered angle 8... 17 (Fitted to Y as standard) Knee, rear X0.36/ Y0.36 X0.36... 1.2/ Y0.36 X0.36/ Y Y0.36... 1.2 8 7 X0.36... 1.2/ Y0.36... 1.2 X NSV0_00436 DT Rated current I e 630 A, 800 A, 1000 A PS* Type Order No. kg Weight per unit approx. X BD2A-1000-LH-G* BVP:261830 1 unit 17.000 X BD2A-1000-LH-X*-G* BVP:261831 1 unit 38.000 X BD2A-1000-LH-Y*-G* BVP:261832 1 unit 38.000 X BD2A-1000-LH-X*/Y*-G* BVP:261833 1 unit 9.000 Knee, front 8 17 Y X NSV0_00437 X0.36/ Y0.36 X0.36... 1.2/ Y0.36 X0.36/ Y0.36... 1.2 X0.36... 1.2/ Y0.36... 1.2 X BD2A-1000-LV-G* BVP:261834 1 unit 17.000 X BD2A-1000-LV-X*-G* BVP:26183 1 unit 38.000 X BD2A-1000-LV-Y*-G* BVP:261836 1 unit 38.000 X BD2A-1000-LV-X*/Y*-G* BVP:261837 1 unit 9.000 Elbow, right Y Elbow, left Y X 8 17 NSV0_00438 X 8-17 NSV0_00439 X0.36/ Y0.36 X0.36... 1.2/ Y0.36 X0.36/ Y0.36... 1.2 X0.36... 1.2/ Y0.36... 1.2 X0.36/ Y0.36 X0.36... 1.2/ Y0.36 X0.36/ Y0.36... 1.2 X0.36... 1.2/ Y0.36... 1.2 Elbow: For G* you must specify the required number of degrees in increments. Optional lengths: For X* and Y* you must specify the required dimension in meters from the center of the joint block to the outside edge of the trunking unit (see also page /81). Special colors available on request. X BD2A-1000-LR-G* BVP:261838 1 unit 17.000 X BD2A-1000-LR-X*-G* BVP:261839 1 unit 38.000 X BD2A-1000-LR-Y*-G* BVP:261840 1 unit 38.000 X BD2A-1000-LR-X*/Y*-G* BVP:261841 1 unit 9.000 X BD2A-1000-LL-G* BVP:261842 1 unit 17.000 X BD2A-1000-LL-X*-G* BVP:261843 1 unit 38.000 X BD2A-1000-LL-Y*-G* BVP:261844 1 unit 38.000 X BD2A-1000-LL-X*/Y*-G* BVP:26184 1 unit 9.000 * You can order this quantity or a multiple thereof. Siemens LV 70 2009 /3
BD2 System 160... 120 A Junction units With aluminum busbars Version Length DT Rated current I e 160 A, 20 A, 400 A PS* Weight per unit approx. Type Order No. kg Flexible junction units (with joint block) (Fitted to Y as standard) 1.2 X BD2-400-R BVP:04889 1 unit 11.000 NSV0_00440 T-units (with joint block) Rear 0.36 X BD2A-400-TH BVP:261797 1 unit 12.800 Front 0.36 X BD2A-400-TV BVP:261800 1 unit 12.800 NSV0_00442 NSV0_00441 Right 0.36 X BD2A-400-TR BVP:261799 1 unit 12.800 NSV0_00443 Left 0.36 X BD2A-400-TL BVP:261798 1 unit 12.800 NSV0_00444 K-units (with joint block) Front/rear 0.36 X BD2A-400-KVH BVP:261792 1 unit 1.300 NSV0_0044 Right/left 0.36 X BD2A-400-KRL BVP:261791 1 unit 1.300 NSV0_00446 Special colors available on request. /36 Siemens LV 70 2009 * You can order this quantity or a multiple thereof.
BD2 System 160... 120 A Junction units With aluminum busbars Version Length DT Rated current I e 630 A, 800 A, 1000 A 1) PS* Weight per unit approx. Type Order No. kg Flexible junction units (with joint block) (Fitted to Y as standard) 1.7 1) X BD2-800-R BVP:04890 1 unit 22.000 NSV0_00440 T-units (with joint block) Rear 0.36 X BD2A-1000-TH BVP:261807 1 unit 2.000 Front 0.36 X BD2A-1000-TV BVP:261810 1 unit 2.000 NSV0_00442 NSV0_00441 Right 0.36 X BD2A-1000-TR BVP:261809 1 unit 2.000 NSV0_00443 Left 0.36 X BD2A-1000-TL BVP:261808 1 unit 2.000 NSV0_00444 K-units (with joint block) Front/rear 0.36 X BD2A-1000-KVH BVP:261802 1 unit 32.000 NSV0_0044 Right/left 0.36 X BD2A-1000-KRL BVP:261801 1 unit 32.000 NSV0_00446 Special colors available on request. 1) BD2-800-R for use up to 800 A. * You can order this quantity or a multiple thereof. Siemens LV 70 2009 /37
BD2 System 160... 120 A Junction units With copper busbars Version L-units (with joint block) (Fitted to Y as standard) Knee, rear Y X NSV0_00428 Length/ Optional length X0.36/ Y0.36 X0.36... 1.2/ Y0.36 X0.36/ Y0.36... 1.2 X0.36... 1.2/ Y0.36... 1.2 DT Rated current I e 160 A, 20 A, 400 A PS* Type Order No. kg Weight per unit approx. X BD2C-400-LH BVP:26188 1 unit 1.200 X BD2C-400-LH-X* BVP:261938 1 unit 31.00 X BD2C-400-LH-Y* BVP:261939 1 unit 31.00 X BD2C-400-LH-X*/Y* BVP:261940 1 unit 48.200 Knee, front Y X NSV0_00429 X0.36/ Y0.36 X0.36... 1.2/ Y0.36 X0.36/ Y0.36... 1.2 X0.36... 1.2/ Y0.36... 1.2 X BD2C-400-LV BVP:261888 1 unit 1.200 X BD2C-400-LV-X* BVP:261941 1 unit 31.00 X BD2C-400-LV-Y* BVP:261942 1 unit 31.00 X BD2C-400-LV-X*/Y* BVP:261943 1 unit 48.200 Elbow, right Elbow, left Y Y X NSV0_00430 X NSV0_00431 X0.36/ Y0.36 X0.36... 1.2/ Y0.36 X0.36/ Y0.36... 1.2 X0.36... 1.2/ Y0.36... 1.2 X0.36/ Y0.36 X0.36... 1.2/ Y0.36 X0.36/ Y0.36... 1.2 X0.36... 1.2/ Y0.36... 1.2 Optional lengths: For X* and Y* you must specify the required dimension in meters from the center of the joint block to the outside edge of the trunking unit (see also page /81). Special colors available on request. X BD2C-400-LR BVP:261887 1 unit 13.300 X BD2C-400-LR-X* BVP:261944 1 unit 30.100 X BD2C-400-LR-Y* BVP:26194 1 unit 30.100 X BD2C-400-LR-X*/Y* BVP:261946 1 unit 46.600 X BD2C-400-LL BVP:261886 1 unit 13.300 X BD2C-400-LL-X* BVP:261947 1 unit 30.100 X BD2C-400-LL-Y* BVP:261948 1 unit 30.100 X BD2C-400-LL-X*/Y* BVP:261949 1 unit 46.600 Version Type suffix Order No. PS* Weight per unit approx. kg Fire barriers for L-units (optional) Fire barrier S120 in limb X X +BD2-S120-BX*-M* BVP:93199 1 unit 1.00 Fire barrier S120 in limb Y X +BD2-S120-BY*-M* BVP:931960 1 unit 1.00 For BX* or BY you must specify the required dimension in meters For the configuration of the fire barriers, see page /94. from the center of the joint block (for BX*: end without joint block) to the center of the fire wall or fire ceiling, for -M* specify the wall For approval in Germany: or ceiling thickness. BD2-S90(S120)-ZUL-D fire protection kit see page /69. /38 Siemens LV 70 2009 * You can order this quantity or a multiple thereof.
BD2 System 160... 120 A Junction units With copper busbars Version L-units (with joint block) (Fitted to Y as standard) Knee, rear Y X NSV0_00428 Length/ Optional length X0.36/ Y0.36 X0.36... 1.2/ Y0.36 X0.36/ Y0.36... 1.2 X0.36... 1.2/ Y0.36... 1.2 DT Rated current I e 630 A, 800 A, 1000 A, 120 A PS* Type Order No. kg Weight per unit approx. X BD2C-120-LH BVP:26189 1 unit 31.900 X BD2C-120-LH-X* BVP:261966 1 unit 72.300 X BD2C-120-LH-Y* BVP:261967 1 unit 72.300 X BD2C-120-LH-X*/Y* BVP:261968 1 unit 112.800 Knee, front Y X NSV0_00429 X0.36/ Y0.36 X0.36... 1.2/ Y0.36 X0.36/ Y0.36... 1.2 X0.36... 1.2/ Y0.36... 1.2 X BD2C-120-LV BVP:261898 1 unit 31.900 X BD2C-120-LV-X* BVP:261969 1 unit 72.300 X BD2C-120-LV-Y* BVP:261970 1 unit 72.300 X BD2C-120-LV-X*/Y* BVP:261971 1 unit 112.800 Elbow, right Elbow, left Y Y X NSV0_00430 X NSV0_00431 X0.36/ Y0.36 X0.36... 1.2/ Y0.36 X0.36/ Y0.36... 1.2 X0.36... 1.2/ Y0.36... 1.2 X0.36/ Y0.36 X0.36... 1.2/ Y0.36 X0.36/ Y0.36... 1.2 X0.36... 1.2/ Y0.36... 1.2 Optional lengths: For X* and Y* you must specify the required dimension in meters from the center of the joint block to the outside edge of the trunking unit (see also page /81). Special colors available on request. X BD2C-120-LR BVP:261897 1 unit 29.00 X BD2C-120-LR-X* BVP:261972 1 unit 70.000 X BD2C-120-LR-Y* BVP:261973 1 unit 70.000 X BD2C-120-LR-X*/Y* BVP:261974 1 unit 110.00 X BD2C-120-LL BVP:261896 1 unit 29.00 X BD2C-120-LL-X* BVP:261919 1 unit 70.000 X BD2C-120-LL-Y* BVP:261920 1 unit 70.000 X BD2C-120-LL-X*/Y* BVP:261921 1 unit 110.00 * You can order this quantity or a multiple thereof. Siemens LV 70 2009 /39
BD2 System 160... 120 A Junction units With copper busbars Version Z-units (with joint block) (Fitted to Y as standard) Rear Z NSV0_00432 X Length/ Optional length X0.36/ Y0.36/ Z0.14... 1.2 X0.36... 0.60/ Y0.36... 0.60/ Z0.14... 1.2 DT Rated current I e 160 A, 20 A, 400 A PS* Type Order No. kg Weight per unit approx. X BD2C-400-ZH-Z* BVP:261906 1 unit 29.700 X BD2C-400-ZH-X*/Y*/Z* BVP:261914 1 unit 37.100 Y Front Y Z X0.36/ Y0.36/ Z0.14... 1.2 X0.36... 0.60/ Y0.36... 0.60/ Z0.14... 1.2 X BD2C-400-ZV-Z* BVP:26190 1 unit 29.700 X BD2C-400-ZV-X*/Y*/Z* BVP:261913 1 unit 37.100 NSV0_00433 X Right Y Z X NSV0_00434 X0.36/ Y0.36/ Z0.34... 1.2 X0.36... 0.60/ Y0.36... 0.60/ Z0.34... 1.2 X BD2C-400-ZR-Z* BVP:261903 1 unit 27.600 X BD2C-400-ZR-X*/Y*/Z* BVP:261911 1 unit 34.100 Left Y Z NSV0_0043 X X0.36/ Y0.36/ Z0.34... 1.2 X0.36... 0.60/ Y0.36... 0.60/ Z0.34... 1.2 Optional lengths: For X* and Y* you must specify the required dimension in meters from the center of the joint block to the outside edge of the trunking unit, for Z* from the outer edge to the outer edge of the trunking unit (see also page /81). Special colors available on request. X BD2C-400-ZL-Z* BVP:261904 1 unit 27.600 X BD2C-400-ZL-X*/Y*/Z* BVP:261912 1 unit 34.100 /40 Siemens LV 70 2009 * You can order this quantity or a multiple thereof.
BD2 System 160... 120 A Junction units With copper busbars Version Z-units (with joint block) (Fitted to Y as standard) Rear Z NSV0_00432 X Length/ Optional length X0.36/ Y0.36/ Z0.26... 1.2 X0.36... 0.60/ Y0.36... 0.60/ Z0.26... 1.2 DT Rated current I e 630 A, 800 A, 1000 A, 120 A PS* Type Order No. kg Weight per unit approx. X BD2C-120-ZH-Z* BVP:261910 1 unit 67.800 X BD2C-120-ZH-X*/Y*/Z* BVP:261918 1 unit 83.00 Y Front Y Z X0.36/ Y0.36/ Z0.26... 1.2 X0.36... 0.60/ Y0.36... 0.60/ Z0.26... 1.2 X BD2C-120-ZV-Z* BVP:261909 1 unit 67.800 X BD2C-120-ZV-X*/Y*/Z* BVP:261917 1 unit 83.00 NSV0_00433 X Right Y Z X NSV0_00434 X0.36/ Y0.36/ Z0.34... 1.2 X0.36... 0.60/ Y0.36... 0.60/ Z0.34... 1.2 X BD2C-120-ZR-Z* BVP:261907 1 unit 64.300 X BD2C-120-ZR-X*/Y*/Z* BVP:26191 1 unit 78.600 Left Y Z NSV0_0043 X X0.36/ Y0.36/ Z0.34... 1.2 X0.36... 0.60/ Y0.36... 0.60/ Z0.34... 1.2 Optional lengths: For X* and Y* you must specify the required dimension in meters from the center of the joint block to the outside edge of the trunking unit, for Z* from the outer edge to the outer edge of the trunking unit (see also page /81). Special colors available on request. X BD2C-120-ZL-Z* BVP:261908 1 unit 64.300 X BD2C-120-ZL-X*/Y*/Z* BVP:261916 1 unit 78.600 * You can order this quantity or a multiple thereof. Siemens LV 70 2009 /41
BD2 System 160... 120 A Junction units With copper busbars Version Length/ Optional length L-units (with joint block), with engineered angle 8... 17 (Fitted to Y as standard) Knee, rear X0.36/ Y0.36 X0.36... 1.2/ Y0.36 X0.36/ Y Y0.36... 1.2 8 7 X0.36... 1.2/ Y0.36... 1.2 X NSV0_00436 DT Rated current I e 160 A, 20 A, 400 A PS* Type Order No. kg Weight per unit approx. X BD2C-400-LH-G* BVP:26190 1 unit 14.700 X BD2C-400-LH-X*-G* BVP:26191 1 unit 31.00 X BD2C-400-LH-Y*-G* BVP:26192 1 unit 31.00 X BD2C-400-LH-X*/Y*-G* BVP:26193 1 unit 48.200 Knee, front 8 17 Y X NSV0_00437 X0.36/ Y0.36 X0.36... 1.2/ Y0.36 X0.36/ Y0.36... 1.2 X0.36... 1.2/ Y0.36... 1.2 X BD2C-400-LV-G* BVP:26194 1 unit 14.700 X BD2C-400-LV-X*-G* BVP:2619 1 unit 31.00 X BD2C-400-LV-Y*-G* BVP:26196 1 unit 31.00 X BD2C-400-LV-X*/Y*-G* BVP:26197 1 unit 48.200 Elbow, right Y Elbow, left Y X 8 17 NSV0_00438 X 8-17 NSV0_00439 X0.36/ Y0.36 X0.36... 1.2/ Y0.36 X0.36/ Y0.36... 1.2 X0.36... 1.2/ Y0.36... 1.2 X0.36/ Y0.36 X0.36... 1.2/ Y0.36 X0.36/ Y0.36... 1.2 X0.36... 1.2/ Y0.36... 1.2 Elbow: For G* you must specify the required number of degrees in increments. Optional lengths: For X* and Y* you must specify the required dimension in meters from the center of the joint block to the outside edge of the trunking unit (see also page /81). Special colors available on request. X BD2C-400-LR-G* BVP:26198 1 unit 13.300 X BD2C-400-LR-X*-G* BVP:26199 1 unit 30.100 X BD2C-400-LR-Y*-G* BVP:261960 1 unit 30.100 X BD2C-400-LR-X*/Y*-G* BVP:261961 1 unit 46.600 X BD2C-400-LL-G* BVP:261962 1 unit 13.300 X BD2C-400-LL-X*-G* BVP:261963 1 unit 30.100 X BD2C-400-LL-Y*-G* BVP:261964 1 unit 30.100 X BD2C-400-LL-X*/Y*-G* BVP:26196 1 unit 46.600 Version Type suffix Order No. PS* Weight per unit approx. kg Fire barriers for L-units (optional) Fire barrier S120 in limb X X +BD2-S120-BX*-M* BVP:93199 1 unit 1.00 Fire barrier S120 in limb Y X +BD2-S120-BY*-M* BVP:931960 1 unit 1.00 For BX* or BY you must specify the required dimension in meters For the configuration of the fire barriers, see page /94. from the center of the joint block (for BX*: end without joint block) to the center of the fire wall or fire ceiling, for -M* specify the wall For approval in Germany: or ceiling thickness. BD2-S90(S120)-ZUL-D fire protection kit see page /69. /42 Siemens LV 70 2009 * You can order this quantity or a multiple thereof.
BD2 System 160... 120 A Junction units With copper busbars Version Length/ Optional length L-units (with joint block), with engineered angle 8... 17 (Fitted to Y as standard) Knee, rear X0.36/ Y0.36 X0.36... 1.2/ Y0.36 X0.36/ Y Y0.36... 1.2 8 7 X0.36... 1.2/ Y0.36... 1.2 X NSV0_00436 DT Rated current I e 630 A, 800 A, 1000 A, 120 A PS* Type Order No. kg Weight per unit approx. X BD2C-120-LH-G* BVP:261922 1 unit 31.900 X BD2C-120-LH-X*-G* BVP:261923 1 unit 72.300 X BD2C-120-LH-Y*-G* BVP:261924 1 unit 72.300 X BD2C-120-LH-X*/Y*-G* BVP:26192 1 unit 112.800 Knee, front 8 17 Y X NSV0_00437 X0.36/ Y0.36 X0.36... 1.2/ Y0.36 X0.36/ Y0.36... 1.2 X0.36... 1.2/ Y0.36... 1.2 X BD2C-120-LV-G* BVP:261926 1 unit 31.900 X BD2C-120-LV-X*-G* BVP:261927 1 unit 72.300 X BD2C-120-LV-Y*-G* BVP:261928 1 unit 72.300 X BD2C-120-LV-X*/Y*-G* BVP:261929 1 unit 112.800 Elbow, right Y Elbow, left Y X 8 17 NSV0_00438 X 8-17 NSV0_00439 X0.36/ Y0.36 X0.36... 1.2/ Y0.36 X0.36/ Y0.36... 1.2 X0.36... 1.2/ Y0.36... 1.2 X0.36/ Y0.36 X0.36... 1.2/ Y0.36 X0.36/ Y0.36... 1.2 X0.36... 1.2/ Y0.36... 1.2 Elbow: For G* you must specify the required number of degrees in increments. Optional lengths: For X* and Y* you must specify the required dimension in meters from the center of the joint block to the outside edge of the trunking unit (see also page /81). Special colors available on request. X BD2C-120-LR-G* BVP:261930 1 unit 29.00 X BD2C-120-LR-X*-G* BVP:261931 1 unit 70.000 X BD2C-120-LR-Y*-G* BVP:261932 1 unit 70.000 X BD2C-120-LR-X*/Y*-G* BVP:261933 1 unit 110.00 X BD2C-120-LL-G* BVP:261934 1 unit 29.00 X BD2C-120-LL-X*-G* BVP:26193 1 unit 70.000 X BD2C-120-LL-Y*-G* BVP:261936 1 unit 70.000 X BD2C-120-LL-X*/Y*-G* BVP:261937 1 unit 110.00 * You can order this quantity or a multiple thereof. Siemens LV 70 2009 /43
BD2 System 160... 120 A Junction units With copper busbars Version Length DT Rated current I e 160 A, 20 A, 400 A PS* Weight per unit approx. Type Order No. kg Flexible junction units (with joint block) (Fitted to Y as standard) 1.2 X BD2-400-R BVP:04889 1 unit 11.000 NSV0_00440 T-units (with joint block) Rear 0.36 X BD2C-400-TH BVP:261889 1 unit 21.900 Front 0.36 X BD2C-400-TV BVP:261892 1 unit 21.900 NSV0_00442 NSV0_00441 Right 0.36 X BD2C-400-TR BVP:261891 1 unit 16.700 NSV0_00443 Left 0.36 X BD2C-400-TL BVP:261890 1 unit 16.700 NSV0_00444 K-units (with joint block) Front/rear 0.36 X BD2C-400-KVH BVP:261884 1 unit 27.100 NSV0_0044 Right/left 0.36 X BD2C-400-KRL BVP:261883 1 unit 20.300 NSV0_00446 Special colors available on request. /44 Siemens LV 70 2009 * You can order this quantity or a multiple thereof.
BD2 System 160... 120 A Junction units With copper busbars Version Length DT Rated current I e 630 A, 800 A, 1000 A, 120 A 1) PS* Weight per unit approx. Type Order No. kg Flexible junction units (with joint block) (Fitted to Y as standard) 1.7 1) X BD2-800-R BVP:04890 1 unit 22.000 NSV0_00440 T-units (with joint block) Rear 0.36 X BD2C-120-TH BVP:261899 1 unit 49.300 Front 0.36 X BD2C-120-TV BVP:261902 1 unit 49.300 NSV0_00442 NSV0_00441 Right 0.36 X BD2C-120-TR BVP:261901 1 unit 37.700 NSV0_00443 Left 0.36 X BD2C-120-TL BVP:261900 1 unit 37.700 NSV0_00444 K-units (with joint block) Front/rear 0.36 X BD2C-120-KVH BVP:261894 1 unit 63.100 NSV0_0044 Right/left 0.36 X BD2C-120-KRL BVP:261893 1 unit 47.900 NSV0_00446 Special colors available on request. 1) BD2-800-R for use up to 800 A. * You can order this quantity or a multiple thereof. Siemens LV 70 2009 /4
BD2 System 160... 120 A Feeder units Selection and ordering data Version DT Rated current I e 160 A, 20 A Feeder units End feeder units without joint block Bolt terminal (bolt included in scope of supply); PE position can be changed Cable entry for multi-core cables from the front PS* Weight per unit approx. DT Rated current I e 160 A, 20 A, 400 A Type Order No. kg Type Order No. kg PS* Weight per unit approx. NSV0_00422 Aluminum X BD2A-20-EE BVP:261993 1 unit 6.600 X BD2A-400-EE BVP:26199 1 unit 13.300 Copper X BD2C-20-EE BVP:262001 1 unit 8.900 X BD2C-400-EE BVP:262003 1 unit 16.300 With cable entry plate 1) Cable entry for single-core cables from the front NSV0_0142 Aluminum X BD2A-20-EE- EBAL Copper X BD2C-20-EE- EBAL With cabling box Cable entry for multi-core cables from 2 sides BVP:611093 1 unit 6.600 X BD2A-400-EE- EBAL BVP:611094 1 unit 8.900 X BD2C-400-EE- EBAL BVP:611097 1 unit 13.300 BVP:611098 1 unit 16.300 NSV0_0143 Aluminum -- X BD2A-400-EE- KR Copper -- X BD2C-400-EE- KR With cabling box and cable entry plate 1) Cable entry for single -core cables from 2sides BVP:61109 1 unit 16.00 BVP:611096 1 unit 19.00 NSV0_01463 Aluminum -- X BD2A-400-EE- KR-EBAL Copper -- X BD2C-400-EE- KR-EBAL Accessories for cable entry, see page /69. 1) Single-core cable entry plate, undrilled. BVP:611099 1 unit 16.00 BVP:611100 1 unit 19.00 /46 Siemens LV 70 2009 * You can order this quantity or a multiple thereof.
BD2 System 160... 120 A Feeder units Version DT Rated current I e 630 A, 800 A, 1000 A Feeder units End feeder units without joint block Bolt terminal (bolt included in scope of supply); PE position can be changed Cable entry for multi-core cables from the front PS* Weight per unit approx. DT Rated current I e 120 A Type Order No. kg Type Order No. kg PS* Weight per unit approx. NSV0_00422 Aluminum X BD2A-1000-EE BVP:261998 1 unit 14.900 Copper X BD2C-1000-EE BVP:262006 1 unit 22.100 X BD2C-120-EE BVP:262009 1 unit 27.100 With cable entry plate 1) Cable entry for single-core cables from the front NSV0_0142 Aluminum X BD2A-1000-EE- EBAL Copper X BD2C-1000-EE- EBAL With cabling box Cable entry for multi-core cables from 2 sides BVP:611103 1 unit 14.900 BVP:611104 1 unit 22.100 X BD2C-120-EE- EBAL BVP:611108 1 unit 27.100 NSV0_0143 Aluminum X BD2A-1000-EE- KR Copper X BD2C-1000-EE- KR With cabling box and cable entry plate 1) Cable entry for single -core cables from 2sides BVP:611101 1 unit 19.900 BVP:611102 1 unit 27.100 X BD2C-120-EE- KR BVP:611107 1 unit 32.100 NSV0_01463 Aluminum X BD2A-1000-EE- KR-EBAL Copper X BD2C-1000-EE- KR-EBAL BVP:61110 1 unit 19.900 BVP:611106 1 unit 27.100 X BD2C-120-EE- KR-EBAL BVP:611109 1 unit 32.100 Accessories for cable entry, see page /69. 1) Single-core cable entry plate, undrilled. * You can order this quantity or a multiple thereof. Siemens LV 70 2009 /47
BD2 System 160... 120 A Feeder units Version DT Rated current I e 160 A, 20 A Feeder units End feeder units with 3-pole switch disconnector and with cable entry plate 1) Cable entry for single-core cables from 3 sides PS* Weight per unit approx. DT Rated current I e 160 A, 20 A, 400 A Type Order No. kg Type Order No. kg PS* Weight per unit approx. Copper X BD2C-20- EESC BVP:611343 1 unit 28.000 X BD2C-31- EESC Copper X BD2C-400- EESC Distribution board feeder units without joint block Bolt terminal (bolt included in scope of supply); PE position can be changed BVP:611344 1 unit 28.000 BVP:61134 1 unit 33.000 Aluminum X BD2A-20-VE BVP:261994 1 unit 2.100 X BD2A-400-VE BVP:261996 1 unit 3.00 Copper X BD2C-20-VE BVP:262002 1 unit 4.400 X BD2C-400-VE BVP:262004 1 unit 6.00 Center feeder units without joint block Bolt terminal (bolt included in scope of supply); edgewise, flat and PE positions can be changed (by rotating the whole busbar section) Cable entry for multi-core cables from 3 sides Aluminum X BD2A-400-ME BVP:261997 1 unit 28.000 Copper X BD2C-400-ME BVP:26200 1 unit 36.600 With cable entry plate 1) Cable entry for single-core cables from 3 sides NSV0_01464 NSV0_00424 NSV0_00423 NSV0_0147 Aluminum X BD2A-400-ME- MBAL Copper X BD2C-400-ME- MBAL Accessories for cable entry, see page /69. 1) Single-core cable entry plate, undrilled. BVP:611110 1 unit 28.000 BVP:611111 1 unit 36.600 /48 Siemens LV 70 2009 * You can order this quantity or a multiple thereof.
BD2 System 160... 120 A Feeder units Version DT Rated current I e 630 A, 800 A, 1000 A Feeder units End feeder units with 3-pole switch disconnector and with cable entry plate 1) Cable entry for single -core cables from 3 sides PS* Weight per unit approx. DT Rated current I e 120 A Type Order No. kg Type Order No. kg PS* Weight per unit approx. Copper X BD2C-630- EESC Copper X BD2C-800- EESC Distribution board feeder units without joint block Bolt terminal (bolt included in scope of supply); PE position can be changed BVP:611346 1 unit 39.000 BVP:611347 1 unit 39.000 Aluminum X BD2A-1000-VE BVP:261999 1 unit 4.700 Copper X BD2C-1000-VE BVP:262007 1 unit 11.800 X BD2C-120-VE BVP:262010 1 unit 16.300 Center feeder units without joint block Bolt terminal (bolt included in scope of supply); edgewise, flat and PE positions can be changed (by rotating the whole busbar section) Cable entry for multi-core cables from 3 sides Aluminum X BD2A-1000-ME BVP:262000 1 unit 47.000 Copper X BD2C-1000-ME BVP:262008 1 unit 7.00 With cable entry plate 1) Cable entry for single -core cables from 3 sides NSV0_01464 NSV0_00424 NSV0_00423 NSV0_0147 Aluminum X BD2A-1000-ME- MBAL Copper X BD2C-1000-ME- MBAL Accessories for cable entry, see page /69. 1) Single-core cable entry plate, undrilled. BVP:611112 1 unit 47.000 BVP:611113 1 unit 7.00 * You can order this quantity or a multiple thereof. Siemens LV 70 2009 /49
BD2 System 160... 120 A Tap-off units for international use Selection and ordering data Version Fuse bases Rated current I e Rated operational voltage U e DT Type Order No. PS* Weight per unit approx. A V kg Molded-plastic enclosures, size 1, up to 2 A With fuse base Without socket outlet 3 D02 2 400 X BD2-AK1/S18 BVP:047112 1 unit 1.10 3 D01 16 400 X BD2-AK1/S14 BVP:047113 1 unit 1.100 With 2 CEE socket outlets, 3-pole, 16 A 2 D01 16 230 X BD2- AK1/2CEE163S14 BVP:047167 1 unit 1.200 With 1 CEE socket outlet, -pole, 16 A 3 D01 16 400 X BD2- AK1/CEE16S14 BVP:047230 1 unit 1.200 With 3 Schuko socket outlets 16 A 3 D01 16 230 X BD2- AK1/3SD163S14 BVP:047284 1 unit 1.400 NSV0_0043 NSV0_0040 NSV0_00449 NSV0_00447 M2 cable grommet included in scope of supply. Screw adapters, fuse links and screw caps are not included in scope of supply. Use plastic cable glands with strain relief (not included in scope of supply). /0 Siemens LV 70 2009 * You can order this quantity or a multiple thereof.
BD2 System 160... 120 A Tap-off units for international use Version Miniature circuit breakers (MCBs) Molded-plastic enclosures, size 1, up to 2 A With miniature circuit breaker Without socket outlet 3-pole, 16 A, characteristic C Rated current I e Rated operational voltage U e DT Type Order No. PS* Weight per unit approx. A V kg 16 400 X BD2-AK1/A163 BVP:047146 1 unit 1.400 With 2 CEE socket outlets, 3-pole, 16 A 2 1-pole, 16 A, characteristic B 16 230 X BD2- AK1/2CEE163A161 BVP:047231 1 unit 1.400 With 1 CEE socket outlet, -pole, 16 A 3-pole, 16 A, characteristic C 16 400 X BD2- AK1/CEE16A163 BVP:047283 1 unit 1.00 With 3 Schuko socket outlets 16 A 3 1-pole, 16 A, characteristic B 16 230 X BD2- AK1/3SD163A161 BVP:04733 1 unit 1.300 With 1 CEE socket outlet, 3-pole, 16 A 1-pole, 16 A, characteristic C RCCBs 2-pole, 2 A/30 ma NSV0_0042 16 230 X BD2-AK1/ CEE163FIA161 BVP:660869 1 unit 1.00 With 2 Schuko socket outlets 16 A 1-pole, 16 A, characteristic B RCCBs 2-pole, 2 A/30 ma NSV0_00477 16 230 X BD2-AK1/ 2SD163FIA161 BVP:660870 1 unit 1.300 Freely assignable (P V max 13 W) Without socket outlet, with integrated standard mounting rail Mounting space for 2 400 X BD2-AK1/F BVP:203247 1 unit 0.700 4 modular widths (MW) NSV0_01466 NSV0_0044 NSV0_0042 NSV0_0041 NSV0_00448 M2 cable grommet included in scope of supply. Use plastic cable glands with strain relief (not included in scope of supply). * You can order this quantity or a multiple thereof. Siemens LV 70 2009 /1
NSV0_0046 NSV0_004 NSV0_0046 NSV0_004 BD2 System 160... 120 A Tap-off units for international use Version Fuse base/miniature circuit breaker Rated current I e Rated operational voltage U e DT Type Order No. PS* Weight per unit approx. A V kg Sheet-steel enclosures, size 02, up to 63 A With fuse base 3-pole fuse base D02 63 400 X BD2-AK02X/S18 BVP:262438 1 unit 4.140 3-pole fuse base S27, 2 00 X BD2-AK02X/S27 BVP:262439 1 unit 3.940 with gauge screw system 3-pole fuse base S33, 63 00 X BD2-AK02X/S33 BVP:26240 1 unit 4.200 with gauge screw system 3-pole fuse base SP38 for cylinder fuses 10 mm 38 mm 2 400 X BD2-AK02X/ F1038-3 BVP:262469 1 unit.00 With miniature circuit breaker Freely assignable (P V max 22. W) With integrated standard mounting rail 4-pole fuse base SP38 for cylinder fuses 10 mm 38 mm 3-pole fuse base SP1 for cylinder fuses 14 mm 1 mm 4-pole fuse base SP1 for cylinder fuses 14 mm 1 mm 3-pole fuse base SP8 for cylinder fuses 22 mm 8 mm 4-pole fuse base SP8 for cylinder fuses 22 mm 8 mm 3-pole, 32 A, characteristic C 3-pole + N, 32 A, characteristic C 3-pole, 63 A, characteristic C 3-pole + N, 63 A, characteristic C Mounting space for 8 modular widths (MW) 2 400 X BD2-AK02X/ F1038-3N 32 400 X BD2-AK02X/ F141-3 32 400 X BD2-AK02X/ F141-3N 63 400 X BD2-AK02X/ F228-3 63 400 X BD2-AK02X/ F228-3N BVP:262470 1 unit.00 BVP:262471 1 unit.00 BVP:262472 1 unit.00 BVP:262473 1 unit.700 BVP:262474 1 unit.700 32 400 X BD2-AK02M2/A323 BVP:26241 1 unit 4.380 32 400 X BD2-AK02M2/A323N BVP:26242 1 unit 4.800 63 400 X BD2-AK02M2/A633 BVP:26243 1 unit.100 63 400 X BD2-AK02M2/A633N BVP:26244 1 unit.200 63 690 X BD2-AK02X/F BVP:26247 1 unit 3.800 With device installation unit, 8 MW Mounting space for 8 modular widths (MW) 63 690 X BD2-AK02M2/F BVP:26248 1 unit 3.900 Special colors available on request. Screw adapters, fuse links and screw caps are not included in scope of supply. Use plastic cable glands with strain relief (not included in scope of supply). /2 Siemens LV 70 2009 * You can order this quantity or a multiple thereof.
NSV0_0047 NSV0_00460 NSV0_0049 NSV0_0048 NSV0_0047 BD2 System 160... 120 A Tap-off units for international use Version Fuse bases Rated current I e Rated operational voltage U e DT Type Order No. PS* Weight per unit approx. A V kg Sheet-steel enclosures, size 2, up to 63 A With fuse base Without socket outlet 3-pole fuse base D02 63 400 X BD2-AK2X/S18 BVP:20313 1 unit 4.140 3-pole fuse base S27, 2 00 X BD2-AK2X/S27 BVP:203136 1 unit 3.940 with gauge screw system 3-pole fuse base S33, with gauge screw system 63 00 X BD2-AK2X/S33 BVP:203138 1 unit 4.200 With 1 CEE socket outlet, -pole, 32 A 3-pole fuse base S33, 32 400 X BD2- with gauge screw system AK2X/CEE32S33 BVP:203142 1 unit.100 With 1 CEE socket outlet, -pole, 63 A 3-pole fuse base S33, 63 400 X BD2-AK2X/ with gauge screw system CEE63S33 BVP:203146 1 unit.680 With 2 CEE socket outlets, -pole, 16 A 2 3-pole fuse base D01 2 3-pole fuse base S27, with gauge screw system 16 400 X BD2- AK2X/2CEE16S14 BVP:203148 1 unit 4.800 16 400 X BD2-AK2X/ BVP:203149 1 unit 4.900 2CEE16S27/FORMP Freely assignable (P V max 22. W) Without socket outlet, with integrated standard mounting rail Mounting space for 8 modular widths (MW) 63 690 X BD2-AK2X/F BVP:20321 1 unit 3.800 Special colors available on request. Screw adapters, fuse links and screw caps are not included in scope of supply. Use plastic cable glands with strain relief (not included in scope of supply). * You can order this quantity or a multiple thereof. Siemens LV 70 2009 /3
NSV0_00472 NSV0_00471 NSV0_00461 NSV0_00464 NSV0_00463a NSV0_00462 NSV0_00462 NSV0_00461 BD2 System 160... 120 A Tap-off units for international use Version Miniature circuit breaker/ fuse base/switch disconnector Sheet-steel enclosures, size 2, up to 63 A With miniature circuit breaker Without socket outlet 3-pole, 32 A, characteristic C Rated current I e Rated operational voltage U e DT Type Order No. PS* Weight per unit approx. A V kg 32 400 X BD2-AK2M2/A323 BVP:203144 1 unit 4.380 With 1 CEE socket outlet, -pole, 16 A 3-pole, 16 A, characteristic C RCCBs 4-pole, 2 A/30 ma 16 400 X BD2-AK2M2/ CEE16FIA163 BVP:660868 1 unit 6.100 With 1 CEE socket outlet, -pole, 32 A 3-pole, 32 A, characteristic C 32 400 X BD2-AK2M2/ CEE32A323 BVP:207986 1 unit 4.900 With 1 CEE socket outlet, -pole, 16 A and 2 Schuko socket outlets 16 A 3-pole, 16 A, characteristic B and 2 1-pole, 16A, characteristic B 16 230 X BD2-AK2M2/ 2SD163CEE16A163 BVP:20310 1 unit.600 With 2 CEE socket outlets, -pole, 16 A 2 3-pole, 16 A, characteristic C 16 400 X BD2-AK2M2/ 2CEE16A163 BVP:20311 1 unit.400 Freely assignable (P V max 22. W) Without socket outlet, with device installation unit Mounting space for 8 modular widths (MW) 63 690 X BD2-AK2M2/F BVP:20322 1 unit 3.900 Sheet-steel enclosures, size 3, up to 12 A With fuse base LV HRC fuse base, size 00; bolt terminal 12 690 X BD2-AK3X/GS00 BVP:203162 1 unit.400 With fuse switch-disconnector LV HRC fuse switchdisconnector, size 00; bolt terminal 12 690 X BD2-AK3X/GSTZ00 BVP:203163 1 unit 6.960 Special colors available on request. Use plastic cable glands with strain relief (not included in scope of supply). /4 Siemens LV 70 2009 * You can order this quantity or a multiple thereof.
NSV0_00468 NSV0_00467 NSV0_0046 NSV0_0046 BD2 System 160... 120 A Tap-off units for international use Version Protection equipment Rated current I e Rated operational voltage U e DT Type Order No. PS* Weight per unit approx. A V kg Sheet-steel enclosures, size 03, up to 12 A With fuse base Bolt terminal 3-pole fuse base SP8 for cylindrical fuses 22 mm 8 mm 4-pole fuse base SP8 for cylindrical fuses 22 mm 8 mm 12 690 X BD2-AK03X/ F228-3 12 690 X BD2-AK03X/ F228-3N BVP:262497 1 unit 7.00 BVP:262498 1 unit 7.00 With fuse switch-disconnector LV HRC fuse switchdisconnector, size 00; bolt terminal 12 690 X BD2-AK03X/ GSTA00 BVP:262496 1 unit 6.960 With fuse switch-disconnector With miniature circuit breaker 3-pole, 12 A, characteristic C 3-pole + N, 12 A, characteristic C Bolt terminal 3-pole, IEC 12 400 X BD2-AK03X/ FS12IEC-3 3-pole, BS 12 400 X BD2-AK03X/ FS12BS-3 4-pole, IEC 12 400 X BD2-AK03X/ FS12IEC-4 4-pole, BS 12 400 X BD2-AK03X/ FS12BS-4 12 400 X BD2-AK03M2/ A123 12 400 X BD2-AK03M2/ A123N BVP:262499 1 unit 7.940 BVP:26200 1 unit 7.940 BVP:26201 1 unit 8.280 BVP:26202 1 unit 8.280 BVP:26248 1 unit.800 BVP:262486 1 unit 6.000 Special colors available on request. Fuse links are not included in scope of supply. Use plastic cable glands with strain relief (not included in scope of supply). * You can order this quantity or a multiple thereof. Siemens LV 70 2009 /
NSV0_00470 NSV0_00470 NSV0_00470 BD2 System 160... 120 A Tap-off units for international use Version Circuit breaker/ setting range Rated current I e Rated operational voltage U e DT Type Order No. PS* Weight per unit approx. A A V kg Sheet-steel enclosures, size 03, up to 12 A With circuit breaker, normal switching capacity, with rotary operating mechanism, terminal connection With thermal-magnetic trip unit 3-pole 3VL27 0 40 400 X BD2-AK03X/ BVP:610402 1 unit 8.00 40... 0 LSD-DC40-N 3VL27 06 63 400 X BD2-AK03X/ BVP:610403 1 unit 8.00 0... 63 LSD-DC63-N 3VL27 08 80 400 X BD2-AK03X/ BVP:610404 1 unit 8.00 63... 80 LSD-DC80-N 3VL27 10 100 400 X BD2-AK03X/ BVP:61040 1 unit 8.00 80... 100 LSD-DC100-N 3VL27 12 12 400 X BD2-AK03X/ BVP:610406 1 unit 8.00 100... 12 LSD-DC12-N With solid-state trip unit, selective 3-pole 3VL27 06 63 400 X BD2-AK03X/ BVP:610407 1 unit 8.00 0... 63 LSD-AE63-N 3VL27 10 80... 100 100 400 X BD2-AK03X/ LSD-AE100-N BVP:610408 1 unit 8.00 With thermal-magnetic trip unit, selective (N release 100 %) 4-pole 3VL27 0 40... 0 3VL27 06 0... 63 3VL27 08 63... 80 3VL27 10 80... 100 3VL27 12 100... 12 Special colors available on request. Use plastic cable glands with strain relief (not included in scope of supply). 40 400 X BD2-AK03X/ LSD-EM40-N 63 400 X BD2-AK03X/ LSD-EM63-N 80 400 X BD2-AK03X/ LSD-EM80-N 100 400 X BD2-AK03X/ LSD-EM100-N 12 400 X BD2-AK03X/ LSD-EM12-N BVP:610397 1 unit 9.000 BVP:610398 1 unit 9.000 BVP:610399 1 unit 9.000 BVP:610400 1 unit 9.000 BVP:610401 1 unit 9.000 /6 Siemens LV 70 2009 * You can order this quantity or a multiple thereof.
BD2 System 160... 120 A Tap-off units for international use Version Circuit breaker/ setting range Rated current I e Rated operational voltage U e DT Type Order No. PS* Weight per unit approx. A A V kg Sheet-steel enclosures, size 04, 0 and 06, up to 30 A With circuit breaker, normal switching capacity, with rotary operating mechanism, bolt terminals With thermal-magnetic trip unit 3-pole 3VL27 16 160 400 X BD2-AK04/ BVP:610424 1 unit 30.000 12... 160 LSD-DC160-N 3VL37 20 200 400 X BD2-AK04/ BVP:610430 1 unit 30.000 160... 200 LSD-DC200-N 3VL37 2 20 400 X BD2-AK04/ BVP:610436 1 unit 30.000 200... 20 LSD-DC20-N 3VL47 40 400 400 X BD2-AK0/ BVP:610442 1 unit 3.000 320... 400 LSD-DC400-N 3VL7 63 30 400 X BD2-AK06/ BVP:610448 1 unit 40.000 NSV0_01011 00... 30 LSD-DC630-N With solid-state trip unit, selective 3-pole 3VL27 16 160 400 X BD2-AK04/ BVP:610428 1 unit 30.000 12... 160 LSD-AE160-N 3VL37 20 200 400 X BD2-AK04/ BVP:610434 1 unit 30.000 160... 200 LSD-AE200-N 3VL37 2 20 400 X BD2-AK04/ BVP:610440 1 unit 30.000 200... 20 LSD-AE20-N 3VL47 40 400 400 X BD2-AK0/ BVP:610446 1 unit 3.000 320... 400 LSD-AE400-N 3VL7 63 30 400 X BD2-AK06/ BVP:61042 1 unit 40.000 NSV0_01011 00... 30 LSD-AE630-N With thermal-magnetic trip unit, selective (N release 60 %) NSV0_01011 4-pole 3VL27 16 12... 160 3VL37 20 160... 200 3VL37 2 200... 20 3VL47 40 320... 400 3VL7 63 00... 30 160 400 X BD2-AK04/ LSD-EC160-N 200 400 X BD2-AK04/ LSD-EC200-N 20 400 X BD2-AK04/ LSD-EC20-N 400 400 X BD2-AK0/ LSD-EC400-N 30 400 X BD2-AK06/ LSD-EC630-N BVP:610426 1 unit 30.000 BVP:610432 1 unit 30.000 BVP:610438 1 unit 30.000 BVP:610444 1 unit 3.000 BVP:61040 1 unit 40.000 Special colors available on request. Use plastic cable glands with strain relief (not included in scope of supply). For BD2-AK04, -AK0 and -AK06, the KT3 or KT4 cable grommet is included in scope of supply. The tap-off units, size 0 and 06, are suitable only for systems 630 A to 120 A. * You can order this quantity or a multiple thereof. Siemens LV 70 2009 /7
BD2 System 160... 120 A Tap-off units for international use Version Circuit breaker/ setting range Rated current I e Rated operational voltage U e DT Type Order No. PS* Weight per unit approx. A A V kg Sheet-steel enclosures, size 04, 0 and 06, up to 30 A With circuit breaker, normal switching capacity, with motorized operating mechanism, bolt terminals With thermal-magnetic trip unit 3-pole 3VL27 16 160 400 X BD2-AK04/ BVP:61042 1 unit 30.000 12... 160 LSM-DC160-N 3VL37 20 200 400 X BD2-AK04/ BVP:610431 1 unit 30.000 160... 200 LSM-DC200-N 3VL37 2 20 400 X BD2-AK04/ BVP:610437 1 unit 30.000 200... 20 LSM-DC20-N 3VL47 40 400 400 X BD2-AK0/ BVP:610443 1 unit 3.000 320... 400 LSM-DC400-N 3VL7 63 30 400 X BD2-AK06/ BVP:610449 1 unit 40.000 NSV0_01012 00... 30 LSM-DC630-N With solid-state trip unit, selective 3-pole 3VL27 16 160 400 X BD2-AK04/ BVP:610429 1 unit 30.000 12... 160 LSM-AE160-N 3VL37 20 200 400 X BD2-AK04/ BVP:61043 1 unit 30.000 160... 200 LSM-AE200-N 3VL37 2 20 400 X BD2-AK04/ BVP:610441 1 unit 30.000 200... 20 LSM-AE20-N 3VL47 40 400 400 X BD2-AK0/ BVP:610447 1 unit 3.000 320... 400 LSM-AE400-N 3VL7 63 30 400 X BD2-AK06/ BVP:61043 1 unit 40.000 NSV0_01012 00... 30 LSM-AE630-N With thermal-magnetic trip unit, selective (N release 60 %) NSV0_01012 4-pole 3VL27 16 12... 160 3VL37 20 160... 200 3VL37 2 200... 20 3VL47 40 320... 400 3VL7 63 00... 30 160 400 X BD2-AK04/ LSM-EC160-N 200 400 X BD2-AK04/ LSM-EC200-N 20 400 X BD2-AK04/ LSM-EC20-N 400 400 X BD2-AK0/ LSM-EC400-N 30 400 X BD2-AK06/ LSM-EC630-N BVP:610427 1 unit 30.000 BVP:610433 1 unit 30.000 BVP:610439 1 unit 30.000 BVP:61044 1 unit 3.000 BVP:61041 1 unit 40.000 Special colors available on request. Use plastic cable glands with strain relief (not included in scope of supply). For BD2-AK04, -AK0 and -AK06, the KT3 or KT4 cable grommet is included in scope of supply. The tap-off units, size 0 and 06, are suitable only for systems 630 A to 120 A. /8 Siemens LV 70 2009 * You can order this quantity or a multiple thereof.
BD2 System 160... 120 A Tap-off units for international use Version Fuse base/fuse switch-disconnector Rated current I e Rated operational voltage U e DT Type Order No. PS* Weight per unit approx. A V kg Sheet-steel enclosures, size 04, 0 and 06, up to 30 A With fuse base, 3-pole, NH1 20 690 X BD2-AK04/SNH1 BVP:610421 1 unit 30.000 bolt terminal NH2 400 690 X BD2-AK0/SNH2 BVP:610422 1 unit 3.000 NH3 30 690 X BD2-AK06/SNH3 BVP:610423 1 unit 40.000 NSV0_01010 Sheet-steel enclosures, size 04 and 0, up to 320 A With fuse switch-disconnector, bolt terminal 3-pole NH1, IEC 22 400 X BD2-AK04/ FS20IEC-3 NH1, BS 22 400 X BD2-AK04/ FS20BS-3 NH2, IEC 320 400 X BD2-AK0/ FS400IEC-3 NH2, BS 320 400 X BD2-AK0/ FS400BS-3 BVP:610409 1 unit 30.000 BVP:610411 1 unit 30.000 BVP:610413 1 unit 3.000 BVP:61041 1 unit 3.000 NSV0_01013 4-pole NH1, IEC 22 400 X BD2-AK04/ FS20IEC-4 NH1, BS 22 400 X BD2-AK04/ FS20BS-4 NH2, IEC 320 400 X BD2-AK0/ FS400IEC-4 NH2, BS 320 400 X BD2-AK0/ FS400BS-4 BVP:610410 1 unit 30.000 BVP:610412 1 unit 30.000 BVP:610414 1 unit 3.000 BVP:610416 1 unit 3.000 NSV0_01013 Special colors available on request. Fuse links are not included in scope of supply. Use plastic cable glands with strain relief (not included in scope of supply). For BD2-AK04, -AK0 and -AK06, the KT3 or KT4 cable grommet is included in scope of supply. The tap-off units, size 0 and 06, are suitable only for systems 630 A to 120 A. * You can order this quantity or a multiple thereof. Siemens LV 70 2009 /9
NSV0_0048 NSV0_00484 BD2 System 160... 120 A Ancillary equipment units for international use Selection and ordering data Version Can be used for Max. power loss P v Rated operational voltage U e DT Type Order No. PS* Weight per unit approx. W V kg Sheet-steel enclosures Ancillary equipment units, freely assignable Built-in standard mounting rail for 8 MW (MW = modular width) Overvoltage protection Remote control/remote switching Intelligence Electronic control equipment Fuse bases Miniature circuit breakers 30 400 X BD2-GKX/F BVP:20316 1 unit 2.800 Sheet-steel enclosures with device installation unit Ancillary equipment units, freely assignable Built-in standard mounting rail for 8 MW (MW = modular width) Remote control/remote switching Intelligence Electronic control equipment Miniature circuit breakers 30 400 X BD2-GKM2/F BVP:203166 1 unit 2.00 Special colors available on request. Including sundries for connecting the enclosures Use plastic cable glands with strain relief (not included in scope of supply). /60 Siemens LV 70 2009 * You can order this quantity or a multiple thereof.
NSV0_00461 BD2 System 160... 120 A Tap-off units for Belgium Selection and ordering data Version Miniature circuit breakers (MCBs) Rated current I e Rated operational voltage U e DT Type Order No. PS* Weight per unit approx. A V kg Molded-plastic enclosures, size 1, up to 20 A With miniature circuit breaker Characteristic C Without socket outlet 1-pole, 16 A 16 230 X BD2-AK1/A161/1 BVP:20319 1 unit 1.100 2-pole, 16 A 16 230 X BD2-AK1/A162 BVP:203170 1 unit 1.200 3-pole + N, 16 A 16 400 X BD2-AK1/A163N BVP:203171 1 unit 1.400 1-pole, 20 A 20 230 X BD2-AK1/A201 BVP:203173 1 unit 1.100 2-pole, 20 A 20 230 X BD2-AK1/A202 BVP:203174 1 unit 1.200 3-pole, 20 A 20 400 X BD2-AK1/A203 BVP:20317 1 unit 1.300 3-pole + N, 20 A 20 400 X BD2-AK1/A203N BVP:203176 1 unit 1.400 With 2 CEE socket outlets, 3-pole, 16 A 2 2-pole, 16 A 16 230 X BD2- AK1/2CEE163A162 BVP:203172 1 unit 1.00 With 2 socket outlets, 3-pole, 16 A 2 2-pole, 16 A 16 230 X BD2- AK1/2PC163A162 BVP:203177 1 unit 1.00 NSV0_00477 NSV0_0041 NSV0_00448 Sheet-steel enclosures, size 2, up to 63 A With miniature circuit breaker Characteristic C Without socket outlet 3-pole + N, 32 A 32 400 X BD2-AK2M2/A323N BVP:203178 1 unit 4.800 3-pole, 63 A 63 400 X BD2-AK2M2/A633 BVP:203179 1 unit.100 3-pole + N, 63 A 63 400 X BD2-AK2M2/A633N BVP:203180 1 unit.200 For BD2-AK1/..., the M2 cable grommet is included in scope of supply. For BD2-AK2M2/... Special colors available on request. Use plastic cable glands with strain relief (not included in scope of supply). * You can order this quantity or a multiple thereof. Siemens LV 70 2009 /61
BD2 System 160... 120 A Tap-off units for Denmark Selection and ordering data Version Fuse base/miniature circuit breaker Rated current I e Rated operational voltage U e DT Type Order No. PS* Weight per unit approx. A V kg Molded-plastic enclosures, size 1, up to 10 A With fuse base With 3 socket outlets 10 A 3 D01 13 230 X BD2- AK1/3DKS103S14 BVP:203167 1 unit 1.200 With miniature circuit breaker With 3 socket outlets 10 A 3 1-pole, 13 A, characteristic C 13 230 X BD2- AK1/3DKS103A131 BVP:203168 1 unit 1.200 NSV0_0044 NSV0_0043 Fuse links and screw caps are not included in scope of supply. /62 Siemens LV 70 2009 * You can order this quantity or a multiple thereof.
NSV0_0047 BD2 System 160... 120 A Tap-off units for France Selection and ordering data Version Fuse base/miniature circuit breaker Molded-plastic enclosures, size 1, up to 2 A With fuse base Without socket outlet 3-pole fuse base SP38 for cylinder fuses 10 mm 38 mm 4-pole fuse base SP38 for cylinder fuses 10 mm 38 mm NSV0_00448 Rated current I e Rated operational voltage U e DT Type Order No. PS* Weight per unit approx. A V kg 2 400 X BD2-AK1/F1038-3 BVP:203189 1 unit 1.100 2 400 X BD2-AK1/F1038-3-N BVP:203190 1 unit 1.200 With miniature circuit breaker Without socket outlet 2-pole, 16 A, characteristic B + 2-pole residualcurrent protective module 40 A/30 ma NSV0_00448 16 230 X BD2-AK1/FI40-162 BVP:214822 1 unit 1.600 Sheet-steel enclosures, size 2, up to 63 A With fuse base Without socket outlet 3-pole fuse base SP1 for cylinder fuses 14 mm 1 mm 3-pole fuse base SP8 for cylinder fuses 22 mm 8 mm 32 400 X BD2-AK2X/F141-3 BVP:203192 1 unit.00 63 400 X BD2-AK2X/F228-3 BVP:203193 1 unit.700 For BD2-AK1/..., the M2 cable grommet is included in scope of supply. For BD2-AK2X/... Special colors available on request. Fuse links are not included in scope of supply. Use plastic cable glands with strain relief (not included in scope of supply). * You can order this quantity or a multiple thereof. Siemens LV 70 2009 /63
NSV0_00471 NSV0_00479 NSV0_00478 NSV0_0047 BD2 System 160... 120 A Tap-off units for the United Kingdom Selection and ordering data Version Fuse base/miniature circuit breaker Rated current I e Rated operational voltage U e DT Type Order No. PS* Weight per unit approx. A V kg Sheet-steel enclosures, size 2, up to 63 A With fuse base Without socket outlet 3 CM32F 32 400 X BD2-AK2X/GB323 BVP:203236 1 unit.00 1 CM32F, L1 32 230 X BD2-AK2X/GB321L1 BVP:611128 1 unit 4.600 1 CM32F, L2 32 230 X BD2-AK2X/GB321L2 BVP:611129 1 unit 4.600 1 CM32F, L3 32 230 X BD2-AK2X/GB321L3 BVP:611130 1 unit 4.600 3 CM63F 63 400 X BD2-AK2X/GB633 BVP:203237 1 unit.600 1 CM63F, L1 63 230 X BD2-AK2X/GB631L1 BVP:611131 1 unit 4.700 1 CM63F, L2 63 230 X BD2-AK2X/GB631L2 BVP:611132 1 unit 4.700 1 CM63F, L3 63 230 X BD2-AK2X/GB631L3 BVP:611133 1 unit 4.700 With 3 socket outlets BS1363, 13 A 3 CM32F 13 230 X BD2- AK2X/3BS133GB131 BVP:203181 1 unit.400 With miniature circuit breaker With 3 socket outlets BS1363, 13 A 3 1-pole, 13 A, characteristic B 13 230 X BD2-AK2M2/ 3BS133A131 BVP:203182 1 unit.600 Sheet-steel enclosures, size 3, 100 A With fuse base 3 CM100F 100 400 X BD2-AK3X/GB1003 BVP:203238 1 unit 7.800 1 CM100F, L1 100 230 X BD2-AK3X/GB1001L1 BVP:611134 1 unit 6.200 1 CM100F, L2 100 230 X BD2-AK3X/GB1001L2 BVP:61113 1 unit 6.200 1 CM100F, L3 100 230 X BD2-AK3X/GB1001L3 BVP:611136 1 unit 6.200 Special colors available on request. Fuse links are not included in scope of supply. Use plastic cable glands with strain relief (not included in scope of supply). /64 Siemens LV 70 2009 * You can order this quantity or a multiple thereof.
NSV0_0046 NSV0_004 BD2 System 160... 120 A Tap-off units for the United Kingdom Version Fuse base Rated current I e Rated operational voltage U e DT Type Order No. PS* Weight per unit approx. A V kg Sheet-steel enclosures, size 02, up to 63 A With fuse base 3 CM32F 32 400 X BD2-AK02X/GB323 BVP:26243 1 unit.00 1 CM32F, L1 32 230 X BD2-AK02X/GB321L1 BVP:61111 1 unit 4.600 1 CM32F, L2 32 230 X BD2-AK02X/GB321L2 BVP:611116 1 unit 4.600 1 CM32F, L3 32 230 X BD2-AK02X/GB321L3 BVP:611117 1 unit 4.600 3 CM63F 63 400 X BD2-AK02X/GB633 BVP:262436 1 unit.600 1 CM63F, L1 63 230 X BD2-AK02X/GB631L1 BVP:611118 1 unit 4.700 1 CM63F, L2 63 230 X BD2-AK02X/GB631L2 BVP:611119 1 unit 4.700 1 CM63F, L3 63 230 X BD2-AK02X/GB631L3 BVP:611120 1 unit 4.700 Sheet-steel enclosures, size 03, 100 A With fuse base 3 CM100F 100 400 X BD2-AK03X/GB1003 BVP:262484 1 unit 7.800 1 CM100F, L1 100 230 X BD2-AK03X/GB1001L1 BVP:611121 1 unit 6.200 1 CM100F, L2 100 230 X BD2-AK03X/GB1001L2 BVP:611122 1 unit 6.200 1 CM100F, L3 100 230 X BD2-AK03X/GB1001L3 BVP:611123 1 unit 6.200 3 R100 100 400 X BD2-AK03X/TPNR1003 BVP:611124 1 unit 7.800 1 R100, L1 100 230 X BD2-AK03X/ BVP:61112 1 unit 6.200 SPNR1001L1 1 R100, L2 100 230 X BD2-AK03X/ BVP:611126 1 unit 6.200 SPNR1001L2 1 R100, L3 100 230 X BD2-AK03X/ BVP:611127 1 unit 6.200 SPNR1001L3 Sheet-steel enclosures, size 04, up to 20 A With fuse base 3 J20 20 400 A BD2-AK04/GB20J-3 BVP:61138 1 unit 32.000 1 J20, L1 20 230 A BD2-AK04/GB20J-L1 BVP:61139 1 unit 29.000 1 J20, L2 20 230 A BD2-AK04/GB20J-L2 BVP:611360 1 unit 29.000 1 J20, L3 20 230 A BD2-AK04/GB20J-L3 BVP:611361 1 unit 29.000 NSV0_01467 Sheet-steel enclosures, size 0, up to 100 A With fuse base 3 3 R100 100 400 A BD2-AK0/GB9R1003 BVP:611362 1 unit 36.00 4 3 R100 100 400 A BD2-AK0/GB12R1003 BVP:611363 1 unit 39.000 NSV0_01467 Special colors available on request. Fuse links are not included in scope of supply. Use plastic cable glands with strain relief (not included in scope of supply). * You can order this quantity or a multiple thereof. Siemens LV 70 2009 /6
BD2 System 160... 120 A Tap-off units for Switzerland Selection and ordering data Version Miniature circuit breakers Rated current I e Rated operational voltage U e DT Type Order No. PS* Weight per unit approx. A V kg Molded-plastic enclosures, size 1, up to 16 A With miniature circuit breaker Characteristic C Without socket outlet 3-pole, 13 A 13 400 X BD2-AK1/A133 BVP:611330 1 unit 1.100 With 3 socket outlets type 23, 16 A 3 1-pole, 16 A 16 230 X BD2-AK1/ 3T23-3A161 BVP:611322 1 unit 1.600 With 1 socket outlet type 2, 16 A 3-pole, 16 A 16 400 X BD2-AK1/T2-A163 BVP:611324 1 unit 1.400 NSV0_00481 NSV0_00480 NSV0_00448 With miniature circuit breaker and RCCB With 2 socket outlets type 23, 16 A NSV0_0009 Characteristic C 1 1-pole, 16 A 2-pole residual-current circuit breaker 16 A/30 ma 16 230 X BD2-AK1/ 2T23-FI162-A161 BVP:611323 1 unit 1.800 M2 cable grommet included in scope of supply. Use plastic cable glands with strain relief (not included in scope of supply). /66 Siemens LV 70 2009 * You can order this quantity or a multiple thereof.
NSV0_00462 NSV0_00464 NSV0_00464 NSV0_00464 NSV0_00464 NSV0_00461 BD2 System 160... 120 A Tap-off units for Switzerland Version Miniature circuit breakers Rated current I e Rated operational voltage U e DT Type Order No. PS* Weight per unit approx. A V kg Molded-plastic enclosures, size 2, up to 63 A With miniature circuit breaker Characteristic C Without socket outlet 3-pole, 2 A 2 400 X BD2-AK2M2/A23 BVP:611331 1 unit 4.600 3-pole, 40 A 40 400 X BD2-AK2M2/A403 BVP:611332 1 unit 4.600 3-pole, 63 A 63 400 X BD2-AK2M2/A633 BVP:611333 1 unit 4.900 With 1 socket outlet type 23, 16 A and 1 CEE socket outlet, -pole, 16 A 1-pole, 16 A; 3-pole, 16 A 16 230, 400 X BD2-AK2M2/ T23-A161/ CEE16-A163 BVP:611326 1 unit.400 With 1 socket outlet type 2, 16 A and 1 CEE socket outlet, -pole, 16 A 2 3-pole, 16 A 16 400 X BD2-AK2M2/ T2-CEE16-2A163 BVP:611327 1 unit.700 With 1 socket outlet type 23, 16 A and 1 CEE socket outlet, -pole, 32 A 1-pole, 16 A; 3-pole, 32 A 16, 32 230, 400 X BD2-AK2M2/ T23-A161/ CEE32-A323 BVP:611328 1 unit.00 With 1 socket outlet type 2, 16 A and 1 CEE socket outlet, -pole, 32 A 3-pole, 16 A; 3-pole, 32 A 16, 32 400 X BD2-AK2M2/ T2-A163/ CEE32-A323 BVP:611329 1 unit.700 With miniature circuit breaker and RCCB With 1 socket outlet type 2, 16 A Characteristic C 3-pole, 16 A 4-pole residual-current circuit breaker 2 A/30 ma 16 400 X BD2-AK2M2/ T2-FI24-A163 BVP:61132 1 unit 4.900 Special colors available on request. * You can order this quantity or a multiple thereof. Siemens LV 70 2009 /67
NSV0_00489 NSV0_00488 NSV0_00487 NSV0_00486 NSV0_00492 NSV0_00491 NSV0_00490 BD2 System 160... 120 A Accessories Selection and ordering data Version DT Rated current I e 160 A, 20 A, 400 A PS* Weight per unit approx. DT Rated current I e 630 A, 800 A, 1000 A, 120 A PS* Weight per unit approx. Type Order No. kg Type Order No. kg Fixing Joint blocks X BD2-400-SK BVP:20316 1 unit 3.00 X BD2-120-EK BVP:261989 1 unit 6.480 End flanges X BD2-400-FE BVP:043977 1 unit 0.980 X BD2-120-FE BVP:261990 1 unit 1.280 Fixing brackets for flat and edgewise installation X BD2-400-BB BVP:0414 1 unit 0.440 X BD2-120-BB BVP:261987 1 unit 0.40 Spacers for 40 mm spacing, for use with fixing bracket X BD2-DSB BVP:20332 10 units 0.030 X BD2-DSB BVP:20332 10 units 0.030 Spacer brackets for wall and ceiling mounting, for use with fixing bracket X BD2-BD BVP:034228 1 unit 0.440 X BD2-BD BVP:034228 1 unit 0.440 Retaining elements for vertical busbar lines Wall mounting, X BD2-BWV BVP:0403 1 unit 1.60 X BD2-BWV BVP:0403 1 unit 1.60 distance from wall adjustable Ceiling mounting X BD2-BDV BVP:0404 1 unit 4.00 X BD2-BDV BVP:0404 1 unit 4.00 /68 Siemens LV 70 2009 * You can order this quantity or a multiple thereof.
NSV0_00494 NSV0_00493 BD2 System 160... 120 A Accessories Version DT Rated current I e 160 A, 20 A, 400 A Fixing Fixing brackets for vertical wall mounting at each connecting flange PS* Weight per unit approx. DT Rated current I e 630 A, 800 A, 1000 A, 120 A Type Order No. kg Type Order No. kg PS* Weight per unit approx. X BD2-BVF BVP:20331 1 unit 0.00 X BD2-BVF BVP:20331 1 unit 0.00 Protective sleeves X BD2-400-D BVP:040 1 unit 4.000 X BD2-120-D BVP:261988 1 unit 4.000 Cable entry Cable entry plates for single-core cable entry, undrilled (drilling template included in scope of supply) NSV0_0049 For use with 20 A end feeder units X BD2-20-EBAL BVP:20330 1 unit 0.300 -- For use with end feeder units or cabling boxes - Up to 400 A or 1000 A X BD2-400-EBAL BVP:0407 1 unit 0.00 X BD2-1000-EBAL BVP:261976 1 unit 1.000 - For 120 A -- X BD2-120-EBAL BVP:261982 1 unit 2.660 For use with center feeder units - Up to 400 A or 1000 A X BD2-400-MBAL BVP:0409 1 unit 0.00 X BD2-1000-MBAL BVP:261980 1 unit 1.000 Cabling boxes, cable entry for multi-core cables from 2 sides, for use with feeder units NSV0_0042 Up to 400 A or 1000 A X BD2-400-KR BVP:0411 1 unit 3.100 X BD2-1000-KR BVP:261978 1 unit.000 For 120A -- X BD2-120-KR BVP:261984 1 unit.000 Version DT Rated current I e 160... 120 A PS* Weight per unit approx. Type Order No. kg Fire barriers Fire protection approval kits (required only for Germany) S90 X BD2-S90-ZUL-D BVP:611397 1 unit 0.200 S120 X BD2-S120-ZUL-D BVP:611398 1 unit 0.200 * You can order this quantity or a multiple thereof. Siemens LV 70 2009 /69
BD2 System 160... 120 A Accessories Version DT Rated current I e 160 A, 20 A, 400 A PS* Weight per unit approx. DT Rated current I e 630 A, 800 A, 1000 A, 120 A PS* Weight per unit approx. Type Order No. kg Type Order No. kg Flanges for degree of protection IP4 Edgewise mounting position At all connection points X BD2-400-HF BVP:0413 1 unit 0.300 X BD2-120-HF BVP:261991 1 unit 0.20 NSV0_00496 At end flanges X BD2-400-HFE BVP:041 1 unit 0.180 X BD2-120-HFE BVP:261992 1 unit 0.260 NSV0_00497 Flat mounting position At all connection points X BD2-FF BVP:0417 1 unit 0.600 X BD2-FF BVP:0417 1 unit 0.600 NSV0_00498 At end flanges X BD2-FFE BVP:0418 1 unit 0.320 X BD2-FFE BVP:0418 1 unit 0.320 NSV0_00499 At top tap-off points X BD2-FAS BVP:0419 1 unit 0.220 X BD2-FAS BVP:0419 1 unit 0.220 Vertical mounting position At all connection points X BD2-400-VF BVP:0420 1 unit 0.200 X BD2-120-VF BVP:26212 1 unit 0.00 NSV0_0001 NSV0_0000 At all tap-off points X BD2-FAS BVP:0419 1 unit 0.220 X BD2-FAS BVP:0419 1 unit 0.220 NSV0_0000 /70 Siemens LV 70 2009 * You can order this quantity or a multiple thereof.
BD2 System 160... 120 A Accessories Version DT Rated current I e 160 A, 20 A, 400 A PS* Weight per unit approx. DT Rated current I e 630 A, 800 A, 1000 A, 120 A PS* Weight per unit approx. Type Order No. kg Type Order No. kg Flanges for degree of protection IP Flanges for IP At all connection points X BD2-400-FS BVP:610369 1 unit 1.700 X BD2-120-FS BVP:610370 1 unit 2.100 NSV0_0101 At end flanges X BD2-400-FSE BVP:610371 1 unit 1.900 X BD2-120-FSE BVP:610372 1 unit 2.600 NSV0_0101 At tap-off points X BD2-FAS BVP:0419 1 unit 0.220 X BD2-FAS BVP:0419 1 unit 0.220 NSV0_0000 Version For tap-off unit DT Type Order No. PS* Weight per unit approx. Type kg Accessories for degree of protection IP Seals for tap-off units BD2-AK1/... X BD2-AK1-IP BVP:610373 1 unit 0.030 NSV0_01016 NSV0_01017 BD2-AK02X/... X BD2-AK02X-IP BVP:610374 1 unit 0.040 BD2-AK03X/... X BD2-AK03X-IP BVP:61037 1 unit 0.040 BD2-AK2X/... X BD2-AK2X-IP BVP:611061 1 unit 0.070 BD2-AK3X/... X BD2-AK3X-IP BVP:611062 1 unit 0.070 BD2-AK04/... X BD2-AK04-IP BVP:611063 1 unit 0.00 BD2-AK0/... X BD2-AK0-IP BVP:611064 1 unit 0.070 BD2-AK06/... X BD2-AK06-IP BVP:61106 1 unit 0.070 NSV0_01018 * You can order this quantity or a multiple thereof. Siemens LV 70 2009 /71
BD2 System 160... 120 A Accessories Version Socket outlets DT Type Order No. PS* Weight per unit approx. kg Socket outlets for tap-off units and ancillary equipment units Socket outlets with adapter enclosure, with wiring, with fixing kit Schuko socket outlet 16 A, 3-pole X BD2-SD163 BVP:20323 1 unit 0.280 CEE socket outlet 16 A, 3-pole X BD2-CEE163 BVP:20324 1 unit 0.260 16 A, -pole X BD2-CEE16 BVP:2032 1 unit 0.310 NSV0_0003 32 A, -pole X BD2-CEE32 BVP:20326 1 unit 0.30 Adapter enclosures for socket outlets with fixing kit X BD2-AG BVP:20327 1 unit 0.10 Adapter plates for use with adapter enclosure For customized socket outlet cut-outs X BD2-APO BVP:20328 1 unit 0.090 With socket outlet cut-out, 44 mm diameter X BD2-APM BVP:20329 1 unit 0.060 NSV0_0006 NSV0_000 NSV0_0004 NSV0_0002 /72 Siemens LV 70 2009 * You can order this quantity or a multiple thereof.
BD2 System 160... 120 A Configuration information Overview Specimen text for tenders Item Quantity Description Unit price Amount... m Busbar trunking system (see Appendix for diagram) As type-tested low-voltage switchgear and controlgear assembly (TTA) according to IEC/EN 60439-1 and -2 Rated current, corresponds to thermal rated current at max. +40 C and +3 C on a 24 h average for indoor installation Rated insulation voltage U i = 690 V AC, 800 V DC; overvoltage category/degree of pollution III/3 Operational voltage... V,... Hz Rated peak withstand current of busbar trunking system,... ka tested according to IEC/EN 60439-1 Degree of protection IP2, increase to IP4 or IP with optional equipment -conductor system: L1, L2, L3, N, PE Busbars: nickel-plated and tinned aluminum or tinned copper; supported by insulated busbar supports Tested for sprinkler systems (with optional equipment) Halogen free system Functional endurance E30, E90 (with additional parts) Trunking units steel-enclosed, galvanized and with paint finish; light gray RAL 703 Busbar connection via joint block with built-in expansion compensation Tap-off points: on two sides every 0. m; offset by 0.2 m Supplied ready for connection with all assembly parts Made by Siemens Type BD2-... Comprising: Siemens LV 70 2009 /73
BD2 System 160... 120 A Configuration information Key to type references for BD2 for various conductor versions BD2. -. -... -... -... (Details of length) (Type length) Current strength [A] Aluminum Copper 160 160 20 20 400 400 630 630 800 800 1000 1000 120 2: L1, L2, L3, 1/1 N, 1/2 PE; 12 tap-off points 3: L1, L2, L3, 1/1 N, 1/1 PE; 12 tap-off points (N conductor with 10 or 200 percent crosssection on request) A: Aluminum C: Copper Sizes of the trunking units (cross-sections) System size 1 System size 2 N L1 L2 L3 ½PE 167 160... 400 A BD2A-2, BD2C-2 trunking units N L1 L2 L3 PE 167 160... 400 A 68 68 BD2A-3, BD2C-3 trunking units, junction units, BD2A-..., BD2C-... feeder units NSV0_00084a NSV0_00086a N L1 L2 L3 ½PE 167 630... 120 A N L1 L2 L3 PE 167 630... 120 A 126 126 BD2. -... -... -... (Length details with junction unit) (Type junction unit, feeder unit) Current strength [A] Aluminum Copper 20 1) 20 1) 400 400 1000 1000 1) 120 A: Aluminum C: Copper Busbars System size 1 System size 2 System accessories Junction units Junction units Tap-off units Feeder units Coupling units (on request) Optional equipment Molded-plastic enclosure up to 2 A With circuit breaker up to 20 A With fuse up to 20 A Feeder units Coupling units (on request) Optional equipment Molded-plastic enclosure up to 2 A With circuit breaker up to 20 A With fuse up to 20 A With circuit breaker up to 630 A With fuse up to 630 A /74 Siemens LV 70 2009
BD2 System 160... 120 A Configuration information Design Notes on supporting structures Examples for mounting flat runs Structures made from standard materials. Manufacturer: Rieth & Co, Kirchheim-Teck, Tel. +49 (0) 7021 977-0. All struts and beams are designed for mounting without a BD2-...-BB fixing bracket. Examples for mounting edgewise runs L L NSV0_00162 L 00 mm 00 mm L 2000 mm L L NSV0_0017 C strut with accessories (left) and double-c strut (right) Length L in 100 mm increments B L 00 mm L 00 mm C strut with accessories (left) and double-c strut (right) Length L in 100 mm increments L NSV0_00164 L 200 mm 100 mm B 600 mm L H strut with beam (without BD2-...-BB fixing bracket) Length L in 100 mm increments, width B in 0 mm increments. L NSV0_0019 NSV0_0016 B 00 mm L 2000 mm L 200 mm Z strut (left) and H strut (right) Length L in 100 mm increments. Trunking units can be secured at the side and at the center of the strut. NSV0_00161 B 100 mm B 600 mm Wall beam (without BD2-...-BB fixing bracket) Width B in 0 mm increments. Example for securing busbar lines between floors NSV0_00166 B 100 mm B 600 mm Wall beam Width B in 0 mm increments 200 mm B 600 mm Tubular beam Width B in 0 mm increments. For securing runs without BD2-...-BB bracket Siemens LV 70 2009 /7
BD2 System 160... 120 A Configuration information Suspension support on flange mount with terminal b NSV0_00167 90 mm b 10 mm For Z and H struts only Securing trunk units on the cable trays NSV0_00168 Can be fitted to standard cable trays using BD2-...-BB fixing bracket or angle clamp. Sundries required Clamp terminals For securing trunking units to the illustrated supporting structures. NSV0_00170 Clamp terminals /76 Siemens LV 70 2009
NSV0_00191 BD2 System 160... 120 A Configuration information Basic configuration information To simplify the configuration of BD2 systems, engineering symbols have been introduced. On the configuration drawings, these symbols clearly indicate the component mounting position, the phase sequence, the open busbar end, the end with the terminal, the position of the flange cover and the side from which the terminal can be accessed. The following conventions apply to all components of the busbar line (feeder units, straight trunking units, branch units and junction units): Open busbar end The PE side is marked with a bold black line. Determining the orientation of L-units 1 NSV0_00174 2 4 3 1 2 3 4 = L = Left = F = Front = R = Right = B = Back Example: NSV0_00171 NSV0_0017 N L1 L2 L3 PE Phase sequence, PE on the right Terminal end of the trunking unit 1 = R = Right 1 1 2 NSV0_00172 1 2 Terminal access side Top flange cover Elbow, right, Type: BD2.-...-LR Determining the orientation of feeder units On feeder units, the position of the cabling box relative to the trunking unit is not critical for type selection, since the busbar connection flange can be turned on site to provide the required phase sequence. Example: SB NSV0_00173 Straight trunking unit with tap-off points on both sides; Type: BD2.-...-SB-. The configuration symbols are used on the selection data pages. End feeder unit (left) and center feeder unit (right) Siemens LV 70 2009 /77
NSV0_00176 BD2 System 160... 120 A Configuration information Route planning: Horizontal installation Mounting positions With the BD2 system, the mounting position can be chosen as required, allowing a horizontal busbar line to be laid out in two ways: N L1 L2 L3 PE PE L3 L2 L1 N Space requirement To ensure easier mounting of the trunking units and tap-off units, minimum clearances from the building's elements must be observed when planning the route. Busbar trunking system without tap-off units: Minimum dimensions for busbar trunking system without tap-off units, including system-conform fixing brackets mounted horizontally on rack or wall beam: Horizontal, edgewise NSV0_00178 b N L1 L2 L3 PE PE L3 L2 L1 N Horizontal, flat As can be seen from the illustration, any phase sequence is possible. A derating factor in horizontal edgewise mounting position ( 0.9) is necessary with power conveyance. This applies for straight trunking units and branch/junction units. The configuration symbol identifying the type shown on the selection page only needs to be turned to the desired mounting position in the engineering drawing. Example: NSV0_00194 a Busbar system Dimension a Dimension b mm mm BD2A(C)-.-160(-400) 100 160 BD2A(C)-.-630(-120) 100 280 Busbar trunking system with tap-off units: Busbar trunking system with tap-off units, including systemconform fixing brackets mounted horizontally on rack or wall beam. The minimum dimension a applies for the front cable entry. NSV0_00180 b Elbow, right, Type: BD2.-...-LR-, flat and edgewise mounting Horizontal edgewise mounting has the advantage of a larger suspension span and the need for fewer accessories (flanges) to achieve the increased degree of protection IP4 (see page /11). a NSV0_0019 Busbar system Dimension a Dimension b mm mm BD2A(C)-.-160(-400) 300 620 BD2A(C)-.-630(-120) 300 680 For a configuring example for horizontal installation see page /84. /78 Siemens LV 70 2009
BD2 System 160... 120 A Configuration information Route planning: Vertical installation Mounting positions When engineering vertical busbar lines (see page /86), the height of the storey measured from the center of one ceiling to the center of the next determines the choice of busbar lengths. If no fire protection is required, standard lengths with protective sleeves can be used. In this case, a minimum distance of 0.18 m must be maintained between the end of the trunking unit enclosure and the upper edge of the protective sleeve. For vertically mounted systems, only one mounting position is possible. The PE bar must always be on the right-hand side, and the trunking unit end with the joint block must point towards the top. This ensures that the flange cover can be push-fitted to the terminal from the front and the screws can be tightened, the tap-off units are not mounted upside-down, i.e. they can only be fitted in the correct position. Space requirement To ensure easier mounting of the trunking units and tap-off units, minimum clearances from the building's elements must be observed when planning the route. Busbar trunking system without tap-off units: a b c b NSV0_00196 1 7 N L1 L2 L3 PE 2 Busbar system Dimension a Dimension b 1) Dimension c 2) (incl. fixing bracket) mm mm mm BD2A(C)-.-160(-400) 130 640 30 BD2A(C)-.-630(-120) 170 640 30 1) Space requirement due to fixing bracket. 2) Distance from wall due to fixing bracket. Busbar trunking system with tap-off units: A busbar system with connected tap-off unit is illustrated. Cable entry is from the bottom. 3 c a 6 PE NSV0_00182 No current reduction is required for vertical busbar lines. For more information about vertical installation see page /86. 4 1 2 3 4 Joint block Tap-off point Cable gland BD2.-...-EE feeder unit Cover 6 Joint block (of the last trunking unit in the vertical busbar run) 7 Tap-off unit Busbar system Dimension a Dimension b Dimension c 1) (incl. fixing bracket) mm mm mm BD2A(C)-.-160(-400) 660 640 30 BD2A(C)-.-630(-120) 700 640 30 1) Distance from wall due to fixing bracket. b NSV0_00197 Siemens LV 70 2009 /79
BD2 System 160... 120 A Configuration information Fire protection The fire protection must always be seated centrally in the fire ceiling. Both standard trunking units and trunking units with optional lengths can be equipped with fire protection through compartmentalization. 10 1 2 Tap-off units For the tap-off units in the vertical run, the mounting position is stipulated. The outgoing cable must be connected from the bottom. This is the case when the PE conductor is on the righthand side viewing from the front. Vertical fixing Vertical fixing brackets at the stipulated maximum intervals (see Table) must be used. The vertical brackets are fitted at the flange of the joint block. Fixtures in between are realized with the spacer bracket combined with the BD2-BB fixing bracket. The distance from the wall can be varied: 30 mm minimum, 82 mm minimum. Maximum length or height of vertical BD2-... busbar lines, supported by one vertical retaining element: Rated operational current Max. length or height BD2A A m m BD2C 160 11.3 10.0 20 10.9 9.9 400 7.9 7.2 630.8.2 800.8 4.8 1000.3 4.1 120 3.2 9 11 8 4 7 6 3 NSV0_00198 $ End flange, termination % Tap-off point & Retaining element for vertical fixing ( Ceiling thickness ) End feeder unit * 1st storey + Center of fire protection, Storey height from center of one ceiling to the center of the next - 2nd storey. 3rd storey / Fixing with BD2-BB and spacer bracket /80 Siemens LV 70 2009
BD2 System 160... 120 A Configuration information Defining the configuration reference dimensions Straight trunking units, standard lengths, type BD2.-.-...-SB-. Standard lengths from center of terminal to center of terminal Example: standard length with tap-off points on both sides, type BD2.-...-SB-3 NSV0_00183 SB 3,2 m Dimensions in the configuration drawings BD2.-2, BD2.-3, tap-off point distance = 0. m 163 167 307 220 NSV0_0091a n 00 Dimensional drawing Straight trunking units, optional lengths, type BD2.-.-...-WB-. Example: BD2.-2, BD2.-3, tap-off point distance = 0. m The open busbar end is used as the reference edge. The grid spacing between the tap-off points is shown in the diagram. 167 n x 20 (00) 20 w PE NSV0_00184 PE L3 L2 L1 N Length Tap-off units on both sides m Number 0.... 1.24 1.2... 2.2 4... 8 2.26... 3.2 8... 12 On optional lengths, it may not be possible to fit tap-off units to all tap-off points. Distance x is the distance between the center of the terminal at the open end and the next tap-off point on the trunking unit. For the standard length x = 20 mm. For optional lengths, 260 mm x 490 mm (depending on the optional length w). Measuring and determining the optional lengths on site a w NSV0_0018 On site, the dimension a between the enclosure edges of the two trunking units to be connected is measured. The optional length is then determined as follows: w[m] = a[m] 0.14 m Junction units X dimension (side with open busbar end): from center of terminal to outside edge of enclosure, Y dimension (side with joint block): from center of terminal to outside edge of enclosure, Z dimension: from outside edge of enclosure to outside edge of enclosure. For dimensioning data see page /102. Siemens LV 70 2009 /81
BD2 System 160... 120 A Configuration information Max. length/height of vertical BD2 busbar lines, supported by one BD2-BWV or BD2-BDV retaining element BD2A-.-... Rated current A 160 20 400 630 800 1000 120 Max. supported length or height m 11.3 10.9 7.9.8.8.3 at max. load (see below) Max. weight per 3.2 m trunking unit fitted with tap-off units kg 0 3 74 106 108 108 BD2C-.-... Rated current A 160 20 400 630 800 1000 120 Max. supported length or height m 10.0 9.9 7.2.2 4.8 4.1 3.2 at max. load (see below) Max. weight per 3.2 m trunking unit kg 0 3 74 106 108 108 108 fitted with tap-off units Notes For taller BD2 busbar lines, additional mountings must be used. The maximum load applied to the BD2-BWV and BD2-BDV vertical retaining elements must not exceed 17 kg. They must be fitted in the area of the terminal. Function Overload and short-circuit protection Busbar trunking systems need to be protected against shortcircuits and overloads. Fuses and circuit breakers are available for use as protective devices. With the selection of this protective device, the level of the expected short-circuit currents, selectivity requirements or operating and signaling functions are also factors for consideration. If circuit breakers are used, the thermally delayed overload release is set to the rated current value for the busbar trunking system. This means that the busbar trunking system can be 100 % loaded. When you decide on your short-circuit protection via fuses and circuit breakers you must not exceed the specified short-circuit strength of the busbar trunking systems. It depends on the level of expected short-circuit current whether a current limiting protective device is required and what shortcircuit breaking capacity the protective device must have. A tabular overview follows of the circuit breakers which can provide short-circuit and overload protection (400 V and 0 Hz) for the corresponding busbar system. The following applies: with I k I cc I cu I k = The expected short-circuit current at the site of installation I cc = Rated conditional short-circuit current of the busbar trunking system I cu = Rated short-circuit breaking capacity of the circuit breaker Type Rated current Circuit breaker with normal Rated conditional short-circuit switching capacity current Circuit breaker Rated conditional with medium short-circuit switching capacity current Circuit breaker with high switching capacity Rated conditional short-circuit current I e A I cu ka I cc ka BD2A(C)-160 160 3VL27 16-1... 40 20 3VL27 16-2... 70 20 3VL27 16-3... 100 20 BD2A(C)-20 20 3VL37 2-1... 40 40 3VL37 2-2... 70 0 3VL37 2-3... 100 0 BD2A(C)-400 400 3VL47 40-1... 4 4 3VL47 40-2... 70 4 3VL47 40-3... 100 4 BD2A(C)-630 630 3VL7 63-1DC36 4 4 3VL7 63-2DC36 70 70 3VL7 63-3DC36 100 100 BD2A(C)-800 800 3VL7 80-1AE36 0 0 3VL7 80-2AE36 70 70 3VL7 80-3AE36 100 100 BD2A(C)-1000 1000 3VL77 10-1AE36 0 0 3VL77 10-2AE36 70 60 3VL77 10-3AE36 100 60 BD2C-120 120 3VL77 12-1AE36 0 0 3VL77 12-2AE36 70 60 3VL77 12-3AE36 100 60 The values for the conditional rated short-circuit current I cc apply to the busbar trunking systems without consideration of any tapoff units. I cu ka I cc ka I cu ka I cc ka /82 Siemens LV 70 2009
BD2 System 160... 120 A Configuration information Temperature characteristic of BD2 systems 0,19 NSV0_00193a Rated current (%) 120 11 110 10 100 9 90 8 80 7 70 6 1 2 3 4 6 NSV0_00186a U (V/m) 0,17 0,1 0,13 0,11 BD2C-.-20 BD2C-.-400 BD2C-.-800 Ambient temperature C (24h average) 0,09 BD2C-.-1000 BD2C-.-630 BD2C-.-160 BD2C-.-120 Voltage drop Voltage drop at rated current The following diagrams show the voltage drop of the BD2A/BD2C systems Taking into account the heat resistors (according to IEC/EN 60439-2) With a load distribution factor a = 1 Under loading with the rated current. (With a different load distribution factor, the curve value must be multiplied by the corresponding distribution factor.) 0,07 0,4 0, 0,6 0,7 0,8 0,9 1,0 cos Voltage drop BD2C Calculation of the voltage drop For long busbar lines, it may be necessary to calculate the voltage drop. ΔU = a 3 I x l (R cos ϕ + X sin ϕ) 10-3 (V) 0,18 NSV0_00192a ΔU = Voltage drop (V) U (V/m) 0,16 BD2A-.-630 BD2A-.-20 BD2A-.-160 I = Load current (A) l = Length (m) a = Load distribution factor 0,14 0,12 BD2A-.-400 BD2A-.-800 BD2A-.-1000 R = Ohmic resistance R 1 (mω/m) X = Inductive resistor X 1 (mω/m) cos ϕ = Power factor (p.f.) Factor "a" used in the equation for calculating the voltage drop is dependent on the load distribution. Load distribution Load distribution Factor a 0,10 A B Infeed at A, one outgoing feeder at B 1 A B C D E Infeed at A, outgoing feeders at B, C, D, E 0. 0,08 0,4 0, 0,6 0,7 Voltage drop BD2A 0,8 0,9 1,0 cos B B D A A E C C Infeed at A, outgoing feeders at B, C 0.2 Infeed at A, outgoing feeders at B, C, D, E 0.12 A C D E F B Infeed at A, B, outgoing feeders at C, D, E, F 0.2 Siemens LV 70 2009 /83
BD2 System 160... 120 A Configuration information Configuration Configuring example: horizontal mounting position Required details The following details are required for configuring BD2 busbar trunking systems (horizontal installation): Installation flat or edgewise, horizontal or vertical, quantity, type and approximate ratings of prospective loads, p.f. Rated diversity factor α Feeding transformers (short-circuit current) Nature of the installation site (dimensions, construction of the building, transport paths, cellar, etc.) Routing of supply lines from other power sources Coordination of lighting system with the BD busbar line Crane operation in installation area Given: 1. Σ of the actual load rating 600 kw, p.f. = 0.8; U e = 400 V 2. Floor plan and machine layout 3. Rated diversity factor α = 0.6 4. Infeed cables 2 18 mm 2 from distribution board. Transformer: 1 00 kva 6. Steel frame shed construction 7. Suspension height 3 m 8. Installed power on machine lines: 200, 182, 118, 100 kw 9. No crane operation 10. Edgewise mounting Operational current The operational current is calculated using the following formula: Determining the operational current Main busbar line: Machine line 200 kw: Machine line 182 kw: Machine line 118 kw: Machine line 100 kw: I B = 600 0.6 1 3 400 0.8 10 3 = 60 A I B = 200 0.6 1 3 400 0.8 10 3 = 217 A I B = 182 0.6 1 3 400 0.8 10 3 = 197 A I B = 118 0.6 1 3 400 0.8 10 3 = 128 A I B = 100 0.6 1 3 400 0.8 10 3 = 108 A Installation plan It contains: Position of the busbar trunking system in the building, Position of the PE and the tap-off openings and consequently the installation direction of the tap-off units, Number of components with item numbers, And the method and height of suspension. The information assists the installer later. If the system is correctly assembled, the entire system will have the same sense of rotation as the three-phase motors throughout the entire system. As a result, it will not be necessary to check the direction of rotation of the motors when relocating a machine. I B = P inst α b 3 U e p.f. 10 3 with: I B = Operational current (A) P inst = Installed power (kw) U e = Rated operational voltage (V) p.f. = Power factor α = Rated diversity factor b = Supply factor b = 1 b = ½ = Single feeder unit = Double end feeder unit, center feeder unit If no data are available about the actual currents occurring simultaneously (derating factor), the following values according to IEC/EN 60439-1 apply: Number of main circuits 2 and 3 4 and 6 to 9 inclusive 10 and more Rated diversity factor α 0.9 0.8 0.7 0.6 /84 Siemens LV 70 2009
BD2 System 160... 120 A Configuration information 1 SIVACON 8PV Machine line II 6 4 2 Machine line IV 6 6 m 11 8 7 7 7 7 4 9 9 9 9 10 11 118 kw 182 kw 1 m 2 22 m Route 2 Machine line IIl 11 10 9 9 9 Machine line V 2 4 6 6 9 7 7 7 7 8 11 2 200 kw 3 100 kw PE, L3, L2, L1, N, Tap-off units N, L1, L2, L3, PE Tap-off units NSV0_00187 36 m 1 2 3 4 Feeder unit Trunking unit End flange Tap-off unit 6 7 8 Tap-off unit Feeder unit Trunking unit Trunking unit 9 Trunking unit 10 Trunking unit 11 End flange Installation plan Suspension: at a height of 3 m with ceiling mounted supporting structures. BD2 busbar line I, 800 A, supplies BD2 runs II, III, IV and V via tap-off units and end feeder units, connected by short cable lengths. Parts list The parts list should contain all the items shown on the installation plan, with type reference, description and quantity. Item No. F (installation site) W L K Type Benennung, Zuordnung Description Dénomination Anzahl Quant. Listenpreis List price Prix brut Einzeln Each Unitaire Zusammen Total 1 BD2A-1000-EE Feeder unit 1 2 BD2A-2-800-SB-3 Trunking units 6 3 BD2-120-FE End flanges 1 4 BD2-AK04/SNH1 Tap-off units 3 BD2-AK3X/GS00 Tap-off units 1 6 BD2A-400-EE Feeder unit 4 7 BD2A-2-160-SB-3 Trunking units 8 8 BD2A-2-160-SB-1 Trunking units 2 9 BD2A-2-20-SB-3 Trunking units 8 1 0 BD2A-2-20-SB-1 Trunking units 2 1 1 BD2-400-FE End flanges 4 1 2 BD2-120-BB Fixing brackets 1 3 BD2-400-BB Fixing brackets 14 Siemens LV 70 2009 /8
BD2 System 160... 120 A Configuration information Configuring example: vertical mounting position Required details Number and height of storeys Ratings and types of load per storey Rated diversity factor α Feeding transformers (characteristics, position) Special requirements (degree of protection, fire protection, etc.) Given: 1. Six storeys with five apartments each 2. 38 kw connected load per apartment 3. U e = 400 V, p.f. = 0.8 4. Rated diversity factor α = 0.8. Derating factor β = 0.4 6. Infeed cables 2 240 mm 2 7. Protection with 3VL7 80 circuit breaker 8. Details and site plans required for routing the trunking Operational current The operational current per storey, which also determines the required rated current of the tap-off units, is calculated using the following formula with: I NB = Operational current per storey (A) P inst = Sum of installed power (kw) per storey U e = Rated operational voltage (V) p.f. = Power factor α = Rated diversity factor If α is not specified, the values from Table 1 can be used. If p.f. is not known, this can be set for a block of apartments = 1. The operational current per busbar line is: with I NB = P inst α 3 U e p.f. I NB = 38 0.8 3 400 0.8 I B = I NB β 10 3 10 3 = 274 A β = Derating factor for the total number of loads. Good empirical values for derating factors can be obtained from your local power supply company. They vary from region to region. Average values are indicated in table 2. Table 1 (according to IEC/EN 60439-1) Table 2: Derating factor Item Factor β Schools, nursery schools 0.6... 0.9 Carpenters' and joiners' workshops 0.2... 0.7 Restaurants, hotels 0.4... 0.7 Butchers 0.... 0.8 Bakeries 0.4... 0.8 Laundries 0.... 0.9 Conference halls 0.6... 0.8 Small offices 0.... 0.7 Large offices 0.4... 0.8 Department stores, supermarkets 0.7... 0.9 Metal processing works 0.2... 0.3 Car factories 0.2... 0.3 Lighting systems for road tunnels 1.0 Building sites 0.2... 0.4 Once the system has been selected, in this case BD2A-2-800, the following documents must be completed to place an order: Installation plan Parts list Order from Parts list Item No. (installation site) F W L K Type Benennung, Zuordnung Description Dénomination 1 BD2A-1000-EE End feeder unit 1 2 BD2A-2-800-WB-2W1,0 Trunking unit with optional 1 +BD2-S120-BX1,00- length 1. m + fire protection a = 1.0 m, ceiling M0,2 thickness M = 0.2 m 3 BD2A-2-800-SB-2 Trunking unit 2.2 m 4 BD2A-2-800-WO-1W1,00 +BD2-S120-BX0.0- M0.2 Trunking unit with optional 4 length 1.0 m + fire protection a = 0. m, ceiling thickness M = 0.2 m BD2-120-FE End flanges 1 6 BD2-BWV Vertical retaining elements 4 7 BD2-120-BB Fixing brackets 8 BD2-BD Spacer bracket 9 BD2-AK0/SNH2 Tap-off unit with LV HRC 6 fuse switch-disconnector Alternatively: 2... 4 BD2A-2-800-SB-3 Trunking unit 3.2 m + fire +BD2-S120-BX1,00- protection a = 1.0 m, ceiling thickness M = 0.2 M0,2 m Anz. Qty. Qté Number of main circuits 2 and 3 4 and 6 to 9 inclusive 10 and more Rated diversity factor α 0.9 0.8 0.7 0.6 /86 Siemens LV 70 2009
BD2 System 160... 120 A Configuration information Installation plan c 6 3 Explanations for the installation plan $ End feeder unit % Trunking unit, optional length 1. m, with fire protection & Trunking unit, standard length 2.2 m ( Trunking unit, optional length 1.0 m, with fire protection ) End flange * Vertical retaining elements + Fixing bracket, Spacer bracket - Tap-off unit 4 a M a Position of fire protection in m; center of fire protection is always at center of fire ceiling b Dimension for spacer bracket in m c Dimension for retaining element in m M Ceiling thickness in m 9 7 8 3 3,2 m Fixing elements: Second retaining element at approx. m height (always near the terminal) Third retaining element at approx. 10 m height Fourth retaining element at approx. 1 m height Note The fixing points for all fixing brackets, retaining elements and spacer brackets must be specified in the installation plan. M b 2 3,10 m 9 a 6 NSV0_00188 1 Siemens LV 70 2009 /87
BD2 System 160... 120 A Configuration information More information Rated currents and short-circuit currents of standard transformers Rated voltage U N 400/230 V 690/400 V Relative short-circuit voltage u k 4 % 1) 6 % 2) 4 % 1) 6 % 2) Rated power Rated current Short-circuit current I" 3) k Rated current Short-circuit current I" 3) k kva A A A A A A 0 72 180 42 1042 100 144 3610 2406 84 2084 1392 160 230 776 380 133 332 2230 200 288 7220 4812 168 4168 2784 20 360 902 601 210 220 360 31 4 1137 783 263 660 4380 400 78 1440 9630 336 8336 68 00 722 1800 12030 420 10440 7120 630 909 2270 1166 26 13300 8760 800 116 28900 19260 672 16672 11136 1000 1444 36100 24060 840 20840 13920 120 180 412 30080 100 26060 17480 1) u k = 4%, standardized according to DIN 4200 for S NT = 0... 630 kva. 2) u k = 6 %, standardized according to DIN 4200 for S NT = 100... 1600 kva. 3) I" k = Transformer initial short-circuit alternating current when connecting to a network with unlimited short-circuit power. Approximating formula Transformer rated current Transformer short-circuit alternating current With I N [A] = k S NT [kva] I" k = I N /u k 100 k = 1.4 at 400 V k = 0.84 at 690 V Dimensioning and selection Safe shutoff of the smallest single-pole ground short-circuit current Since the level of the loop impedance is decisive in determining the level of the single-pole short-circuit current, DIN VDE 0100 Part 600 prescribes that the loop impedance must be determined between the following: Phase conductor and the protective conductor or Phase conductor and PEN conductor. This value may be determined by: Measuring with measuring devices or Calculation or Simulation of the network in a network model. In the "Technical Specifications" section, the impedance values for the BD2A/BD2C busbar trunking systems are listed so that it is possible to calculate the loop impedances of a busbar system, which contributes to the total loop impedance. With the aid of the loop impedance of the entire busbar trunking system, it is easy to calculate the smallest expected single-pole short-circuit current. I kl min = c U n 3 Z k with c = Voltage factor 0.9 U n = Voltage between the phase conductors Z k = Short-circuit impedance Note: DIN VDE 0100 is equivalent to IEC 60364. /88 Siemens LV 70 2009
BD2 System 160... 120 A Degrees of protection for busbar trunking systems Room types according to DIN VDE 0100 (IEC 60364) Closed electrical operating areas Electrical operating areas Dry areas and rooms Damp and wet areas and rooms Designation of the degree of protection according to IEC/EN 6029 IP10 IP20 IP20 IP20 Degrees of protection of electrical equipment according to IEC/EN 6029 Configuration information Usage in operating areas exposed to a fire hazard In operating areas exposed to a fire hazard, IEC 60364-7-72 and DIN VDE 0100-720 places enhanced demands on the degree of protection of electrical equipment. The demands for busbar trunking systems are: For a fire hazard from dust and/or fibers: degree of protection IPX For a fire hazard from readily flammable materials apart from dust and/or fibers: degree of protection IP4X The BD2A/BD2C busbar trunking systems meet these demands. They are therefore suitable for applications in this area. Degree of 1. figure 2. figure protection Touch protection Protection against solid foreign bodies and dust Protection against ingress of liquid IP00 No special protection No special protection No special protection IP20 Against finger contact Against solid bodies 12. mm No special protection IP34 Against tools Against solid bodies 2. mm No damage caused by splashwater IP41 Against wire Against solid bodies 1 mm No damage caused by vertically dripping water (vertical drops) IP43 Against wire Against solid bodies 1 mm No damaged caused by spraywater IP4 Against wire Against hazardous dust deposits inside (dust-tight) No damage caused by splashwater IP Against wire Against hazardous dust deposits inside (dust-tight) No damage caused by hose-water IP6 Against wire Against penetration of dust (dust-tight) No damage caused by hose-water IP66 Against wire Against penetration of dust (dust-tight) In the event of temporary immersion, ingress of water will have no harmful effects (water jet) IP67 Against wire Against penetration of dust (dust-tight) Water may not ingress in harmful quantities during immersion (temporary immersion) IP68 Against wire Against penetration of dust (dust-tight) Water may not ingress in harmful quantities during immersion for indefinite periods (continuous immersion) Touch protection against direct contact according to EN 0274 These regulations apply for the design of electrical equipment and its installation in electrical installations with rated voltages up to 1000 V AC or 100 V DC regarding protection against direct contact, where there are actuators (pushbuttons, toggle levers etc.) located in the direct vicinity of parts which are live or dangerous to touch. "Finger-safe" relates only to the operating device (actuator) and only in the normal direction of actuation. A minimum distance of r = 30 mm in radius from the center point of the device to any live parts must be ensured. The degree of protection IP20 is a more enhanced touch protection against direct contact than "finger-safe". It constitutes touch protection with electrical equipment from all directions. Devices with "finger-safe" touch protection and degree of protection IP00 can be assigned with additional touch protection by shrouding if required. Siemens LV 70 2009 /89
BD2 System 160... 120 A Configuration information Power distribution systems (grid types) according to IEC 60364-3 or DIN VDE 0100-300 Determination of the protective measures and selection of the electrical equipment in accordance with the power distribution system used. TN systems TN-S system L1 L2 L3 N PE Other systems TT system L1 L2 L3 N NSV0_01081 PE 1 1 NSV0_01078 Separated neutral and protective conductors throughout the system. TN-C system L1 L2 In a TT system, one point is directly earthed; the chassis of the electrical system is connected to earth which has no direct connection to the power earth. In the modern TT system, protective measures include protective grounding as well as current-operated e.l.c.b. systems and voltageoperated e.l.c.b. systems. IT system L1 L2 L3 PEN L3 2 NSV0_01082 PE 1 1 NSV0_01079 Neutral and protective functions are combined throughout the system in a single conductor. TN-C-S system L1 L2 L3 PEN NSV0_01080 PE N 1 Combination between neutral conductor and protective earth functions. They are combined in one part of the system to a single conductor and separated in another part. $ Chassis % Impedance In the IT system there is no direct connection between the live conductors and earthed components; the chassis of the electrical system is earthed. The IT system corresponds with the system where a protective earth system for protective measures is applied. Explanations First character = grounding condition of the power supply source T = direct grounding of a point I = either insulation of all live parts from earth or connection of one point with earth via impedance Second character = grounding condition of chassis of the electrical equipment T = chassis directly earthed, independently of any grounding of a point in the power supply N = chassis connected directly with the system earth in AC systems, the earth point is normally the neutral point Additional characters = arrangement of the neutral conductor and protective earth conductor S = separate conductors for neutral and protective earth functions C = neutral and protective earth functions combined in a single conductor (PEN) /90 Siemens LV 70 2009
BD2 System 160... 120 A Configuration information Functional endurance Fire protection equipment and fire protection precautions for electrical installations are required especially with building structures of a particular type of utilization. Buildings of this nature include hospitals and places where people gather. The German standards DIN VDE 0108-1 "Buildings where people meet" and DIN VDE 0100-710 "Medically used areas" state that electrical systems must remain operational for certain periods of time in the event of a fire. This applies in particular to: Fire alarm systems Systems for sounding alarms and conveying instructions to visitors and employees Emergency lighting Passenger elevators with evacuation circuit which must remain serviceable in the incoming feeder area for at least 30 minutes under post-flashover fire conditions Water-pressure boosting equipment for firefighting water supply Ventilation systems of enclosed stairwells, elevator shafts and drive equipment rooms for fire service elevators must remain operational for at least 90 minutes. 1000 C Magnetic fields General information The busbars intended for power conveyance generate - as do all other conductors - alternating electromagnetic fields with a base frequency of 0 Hz. These magnetic fields can negatively influence the function of sensitive equipment such as computers or measurement devices. Limit values The EMC directives and the standards derived from these do not contain any regulations or recommendations for engineering busbar trunking system installations. If busbar trunking systems are used in medical facilities, the DIN VDE 0100-710 standard can be consulted. In DIN VDE 0100-710, guide values of mains frequency induced magnetic fields in facilities used for medical purposes are defined. Stations where patients are treated may not be subject to magnetic induction at 0 Hz which exceeds the following values: B = 2 10-7 Tesla for EEG B = 4 10-7 Tesla for ECG In order to make it possible to decide in the planning stage which busbars should be used, Siemens has carried out extensive magnetic field measurements. The magnetic radiated noise of the busbar systems was measured using a 9.6 m long straight busbar arrangement. The busbars were loaded symmetrically with the rated current and the magnetic fields measured in their horizontal and vertical axes. 00 Z 0 0 30 60 90 120 10 (min) 180 NSV0_01072 NSV0_01046 X Standard temperature curve (ETK) for assessing functional endurance In order to provide the functional endurance of the busbar trunking system stipulated by the regulations, Siemens successfully carried out and completed tests in cooperation with Promat for BD2A/BD2C busbar system at the materials testing laboratory in Braunschweig in Germany. During the fire tests, the busbar trunking systems were equipped with a cladding of Promatect L00 plates of various thicknesses (thickness d = 20 mm, 40 mm, 60 mm) and were subjected to a fire load of of external origin as defined by the "standard temperature curve (ETK)" in order to assess the functional endurance according to DIN 4102 Part 12. More information on request. System of coordinates for magnetic field measurement The limit value for inductive interference between multi-core cables and wires of the high-current system, conductor crosssection > 18 mm 2, and the stations where patients are treated will certainly not be exceeded if a minimum distance of 9 m as recommended by the DIN VDE 0100-710 standard is observed. When busbars are used, this distance will usually turn out to be less since the sheet-steel enclosure is effective in reducing magnetic interference fields in the environment. Measured values on request. Note: DIN VDE 0100 is equivalent to IEC 60364. Siemens LV 70 2009 /91
BD2 System 160... 120 A Configuration information Sprinkler test General information Sprinkler fire-extinguishing systems in particular are used for protecting cable conduits and cable ducts. Here it is predominantly the cooling effect of the water on the surface of the fire which is exploited. Operation of the sprinkler for at least 30 minutes should be assumed. Siemens has subjected its BD2A/BD2C busbar trunking systems to an extensive range of tests with sprinkler systems. Due to the absence of a mandatory standard or directive, the test was performed using a test setup which mirrored a practical application (see the sketch). Test results With the BD2A/BD2C busbar trunking system, the system with IP4 degree of protection was sprinkled in all fitted positions paying close consideration to the "VdS" directives for sprinkler systems. The insulation resistance was measured before and after sprinkling for 90 minutes, and a high voltage test according to EN 60439-2 was performed. This test was absolved successfully and indicated that the system could be operated immediately after sprinkling without any delays. 2 1... 10 bar 3 1 1 Sprinkler 2 Manometer 3 Shutoff valve 4 Tap-off unit Trunking unit 00 4 NSV0_0100 Sprinkler test setup /92 Siemens LV 70 2009
BD2 System 160... 120 A Comparison of busbar trunking and cable installation systems Feature Busbar trunking installation Cable installation TTA assembly Yes No Mechanical safety High Low Fire load Low High Temperature characteristic System structure Protective devices for loads Ambient temperature According to IEC/EN 60439-1 and -2 max. +40 C and +3 C on a 24 hour average Clear due to linear system structure with in-line load feeders via tap-off units In the tap-off unit: Means direct and immediate on-the-spot identification of assignment to load Configuration information According to DIN 7298 Part 4/ VDE 0298 Part 4/2.88 loads are based on +30 C. Very large accumulation of cables at feed point due to point-to-point supply of loads from central power distribution unit Centrally in the distribution board: Makes the assignment to the load not directly verifiable. It is necessary to rely on correct inscription of the cables and loads. Space requirement Low High as the corresponding distribution boards are required. Routing criteria (cable accumulation, type of routing, current carrying capacity, etc.) must be complied with. Retrofitting capability if load feeders are changed Planning and configuration Dimensioning (current, voltage drop, protective earth conditions) Great flexibility due to tap-off points in the trunking units and a great number of different tap-off units Simple and fast with EDP-aided planning tools being used Not complex Only possible at great expense; laying additional cables from the central distribution board to the load. Highly intensive configuration (distribution and cable layouts, cable plans, etc.) Very complex Troubleshooting Low High Fire protection Type-tested, ex-works Dependent on the work standard applied on the building site Functional endurance Tested functional endurance according to DIN 4102-12 Dependent on the work standard applied on the building site Electromagnetic interference Low, due to sheet-steel enclosure and conductor Relatively high with a standard cable configuration Mounting Very little fitting materials and tools required, short mounting times Complex mounting materials and a comprehensive range of tools required, long mounting times Weight Up to l of the comparable cable weight Up to 3-times the busbar trunking system weight Halogen and PVC free Trunking units are always halogen and PVC free Standard cables are not always halogen and PVC free Siemens LV 70 2009 /93
NSV0_00190a NSV0_00189 BD2 System 160... 120 A Fire barriers Overview General requirements The German state building authorities demand that buildings are designed so that "spreading of fire and smoke is prevented, and that effective fire fighting and rescue of persons and domestic animals is facilitated". Fire or flue gas may not spread from one storey or fire area to another. All BD2A/BD2C busbar trunking systems can be equipped with fire barriers and generally comply with the standards for buildings including high-rise buildings. The busbar trunking system is supplied ex-works with fire barriers. Retrofitting is not possible. A general approval from the German Institute for Building Engineering (Deutsches Institut für Bautechnik in Berlin DIBt) in Berlin is available: BD2-S120: No. Z-19.1-1046, BD2-S90: No. Z-19.1-1048). The fire resistance class with the BD2 system corresponds with version S 90 or S 120 according to DIN 4102 Part 9. The demands for verification of fire resistance duration at 120 min as specified to ISO 834 according to IEC/EN 60439-2 are fulfilled. The requirements for a busbar trunking system as specified to DIN 4102 are shown in the illustration. 4 3 1 The center of the fire barrier in the trunking unit must be positioned in the center of the fire wall or ceiling. Exception: With branch/junction units, this may not be possible due to insufficient distance from the wall or ceiling, i.e. the center of the fire barrier may not coincide with the center of the fire wall or ceiling. In such cases, PROMATECT-H(L) panels are added to achieve the actually required wall or ceiling thickness. The following information must be provided: For BX*, BY* or BZ* trunking units, position of the center of the fire barrier in the trunking unit (or the center of the fire wall or ceiling for branch/junction units with insufficient distance from the wall or ceiling); the desired fire resistance rating S90 or S120; and the thickness M* of the wall or ceiling. There are no tap-off points in the area covered by the fire barrier. The trunking units must be installed by an approved fire protection installation specialist. In Germany, the BD2-S90-ZUL-D or BD2-S120-ZUL-D fire protection kit is required (see page /69). Notes For BX* and BY*, replace the asterisk in the type reference by the required dimension in meters from the center of the joint block to the center of the fire wall or ceiling. For BZ*, replace the asterisk in the type reference by the required dimension in meters from the outside edge of limb X (end without joint block) to the center of the fire wall or ceiling; for -M* specify the wall or ceiling thickness. 2 1 BX*, BY*, BZ* M* 1 Center line of fire barrier NSV0_01070 Positioning in the fire wall (1) Permissible temperature increase on components: max. 180 C (2) Scene of fire: application of fire according to the standard temperature curve DIN 4102, sheet 2 (3) Permitted temperature increase of escaping air: max. 140 C (4) No flammable gases are permitted to escape. No rescue work may be hindered by emerging smoke. Configuration To ensure fire protection to the S90 or S120 function, the following points must be observed when configuring and installing trunking units and junction units with fire barriers: M* BX*, BY*, BZ* 1 Center line of fire barrier 1 Positioning in the fire ceiling /94 Siemens LV 70 2009
BD2 System 160... 120 A Fire barriers Design Position of fire barrier on the trunking unit L 20 NSV0_01019 BX* Type: BD2A-...-S(W).-. + BD2-S90(S120)-BX*-M* BD2C-...-S(W).-. + BD2-S120-BX*-M* Fire resistance rating S90 Wall thickness M 10 mm BD2A-...-S(W). + BD2-S90-BX*-M* 1) 10 L (L min. = 370+M) BX* min. = 18+M/2 BX*max. = L BX* min. 20 (min.) 260 260 320 (max.) 260 2980 M NSV0_01020 Fire resistance rating S120 Wall thickness 10 mm M < 20 mm BD2A-...-S(W). + BD2-S120-BX*-M* 1) L (L min. = 70+M) BX* min. = 28+M/2 BX*max. = L BX* min. 720 (min.) 360 360 M = 10... 20 100 100 NSV0_01021 320 (max.) 360 2890 Wall thickness M 20 mm BD2A-...-S(W). + BD2-S120-BX*-M* 1) 20 L (L min. = 370+M) BX* min. = 18+M/2 BX*max. = L BX* min. 620 (min.) 310 310 320 (max.) 310 2940 M NSV0_01022 1) Replace the asterisk * according to the table. Siemens LV 70 2009 /9
BD2 System 160... 120 A Fire barriers Fire resistance rating S120 Wall thickness M 10 mm BD2C-...-S(W). + BD2-S120-BX*-M* 1) 10 18 L (L min. = 740+M) BX* min. = 370+M/2 BX*max. = L BX* min. 900 (min.) 40 40 320 (max.) 40 2800 18 M NSV0_01023 1) Replace the asterisk * according to the table. Position of the fire barrier on branch/junction units The minimum dimensions applicable for positioning fire barriers on the limbs of branch/junction units differ, depending on the routing of the trunking and the distance from the fire wall to the inside edge of the trunking unit. Y* (X*) NSV0_0102 BY* (BX*) Y* (X*) X* (Y*) BY* (BX*) 170 NSV0_01024 c X* (Y*) e 160... 400 A 00... 120 A c 70 130 Elbow, type: BD2A-...-LR(L)-X* (Y*), +BD2-S90(S120)-BX*(BY*)-M* BD2C-...-LR(L)-X* (Y*), +BD2-S120-BX*(BY*)-M* Knee, type: BD2A-...-LV(H)-X* (Y*), +BD2-S90(S120)-BX*(BY*)-M* BD2C-...-LV(H)-X* (Y*), +BD2-S120-BX*(BY*)-M* Fire resistance rating S90 Wall thickness 10 mm M < 20 mm (distance from wall/inside corner A 200 mm) A 200 BD2A-...-L... + BD2-S90-BX*(BY*)-M* 1) Junction units LL, LR X*(Y*)(X*(Y*) min. = 18+M+A+170) BX*(BY*) min. = 18+M/2 710 (min.) 260 260 120 (max.) 260 800 Junction units LV, LH; 400 A BX*(BY*) max. = X*(Y*)-170-A-M/2 10 M < 20 NSV0_01026 X*(Y*)(X*(Y*) min. = 18+M+A+70) BX*(BY*) min. = 18+M/2 610 (min.) 260 260 120 (max.) 260 900 Junction units LV, LH; 1000 A X*(Y*)(X*(Y*) min. = 18+M+A+130) BX*(BY*) min. = 18+M/2 670 (min.) 260 260 120 (max.) 260 840 BX*(BY*) max. = X*(Y*)-70-A-M/2 BX*(BY*) max. = X*(Y*)-130-A-M/2 1) Replace the asterisk * according to the table. /96 Siemens LV 70 2009
BD2 System 160... 120 A Fire barriers Fire resistance rating S90 Wall thickness 10 mm M < 20 mm (distance from wall/inside corner 30 mm A < 200 mm) M = 10... 20 A = 30... 190 100 NSV0_01027 BD2A-...-L... + BD2-S90-BX*(BY*)-M* 1) Junction units LL, LR X*(Y*)(X*(Y*) min. = 28+M+A+170) BX*(BY*) min. = 28+M/2 640 (min.) 360 360 120 (max.) 360 970 Junction units LV, LH; 400 A X*(Y*)(X*(Y*) min. = 28+M+A+70) BX*(BY*) min. = 28+M/2 40 (min.) 360 360 120 (max.) 360 1070 BX*(BY*) max. = X*(Y*)-170-A-M/2 BX*(BY*) max. = X*(Y*)-70-A-M/2 Junction units LV, LH; 1000 A X*(Y*)(X*(Y*) min. = 28+M+A+130) BX*(BY*) min. = 28+M/2 600 (min.) 360 360 120 (max.) 360 1010 BX*(BY*) max. = X*(Y*)-130-A-M/2 Fire resistance rating S90 Wall thickness M 20 mm (distance from wall/inside corner A 30 mm) A 30 M 20 NSV0_01028 BD2A-...-L... + BD2-S90-BX*(BY*)-M* 1) Junction units LL, LR X*(Y*)(X*(Y*) min. = 18+M+A+170) BX*(BY*) min. = 18+M/2 640 (min.) 310 310 120 (max.) 310 920 Junction units LV, LH; 400 A X*(Y*)(X*(Y*) min. = 18+M+A+70) BX*(BY*) min. = 18+M/2 40 (min.) 310 310 120 (max.) 310 1020 BX*(BY*) max. = X*(Y*)-170-A-M/2 BX*(BY*) max. = X*(Y*)-70-A-M/2 Junction units LV, LH; 1000 A X*(Y*)(X*(Y*) min. = 18+M+A+130) BX*(BY*) min. = 18+M/2 600 (min.) 310 310 120 (max.) 310 960 BX*(BY*) max. = X*(Y*)-130-A-M/2 1) Replace the asterisk * according to the table. Note: With other fire barrier configurations, please contact your local Siemens sales office. Siemens LV 70 2009 /97
BD2 System 160... 120 A Fire barriers Fire resistance rating S120 Wall thickness 10 mm M < 20 mm (distance from wall/inside corner A 200 mm) BD2A-...-L... + BD2-S120-BX*(BY*)-M* 1) Junction units LL, LR M = 10... 20 A 200 100 100 NSV0_01029 X*(Y*)(X*(Y*) min. = 28+M+A+170) BX*(BY*) min. = 28+M/2 810 (min.) 360 360 120 (max.) 360 800 Junction units LV, LH; 400 A X*(Y*)(X*(Y*) min. = 28+M+A+70) BX*(BY*) min. = 28+M/2 710 (min.) 360 360 120 (max.) 360 900 Junction units LV, LH; 1000 A X*(Y*)(X*(Y*) min. = 28+M+A+130) BX*(BY*) min. = 28+M/2 770 (min.) 360 360 120 (max.) 360 840 BX*(BY*) max. = X*(Y*)-170-A-M/2 BX*(BY*) max. = X*(Y*)-70-A-M/2 BX*(BY*) max. = X*(Y*)-130-A-M/2 Fire resistance rating S120 Wall thickness M 20 mm (distance from wall/inside corner A 200 mm) BD2A-...-L... + BD2-S120-BX*(BY*)-M* 1) Junction units LL, LR M 20 A 200 NSV0_01030 X*(Y*)(X*(Y*) min. = 18+M+A+170) BX*(BY*) min. = 18+M/2 810 (min.) 310 310 120 (max.) 310 70 Junction units LV, LH; 400 A X*(Y*)(X*(Y*) min. = 18+M+A+70) BX*(BY*) min. = 18+M/2 710 (min.) 310 310 120 (max.) 310 80 BX*(BY*) max. = X*(Y*)-170-A-M/2 BX*(BY*) max. = X*(Y*)-70-A-M/2 Junction units LV, LH; 1000 A X*(Y*)(X*(Y*) min. = 18+M+A+130) BX*(BY*) min. = 18+M/2 770 (min.) 310 310 120 (max.) 310 790 BX*(BY*) max. = X*(Y*)-130-A-M/2 1) Replace the asterisk * according to the table. Note: With other fire barrier configurations, please contact your local Siemens sales office. /98 Siemens LV 70 2009
BD2 System 160... 120 A Fire barriers Fire resistance rating S120 Wall thickness 10 mm M < 20 mm (distance from wall/inside corner 30 mm A < 200 mm) BD2A-...-L... + BD2-S120-BX*(BY*)-M* 1) Junction units LL, LR A 30... 190 100 X*(Y*)(X*(Y*) min. = 28+M+A+170) BX*(BY*) min. = 28+M/2 640 (min.) 360 360 120 (max.) 360 970 BX*(BY*) max. = X*(Y*)-170-A-M/2 M =10... 20 100 NSV0_01031 Junction units LV, LH; 400 A X*(Y*)(X*(Y*) min. = 28+M+A+70) BX*(BY*) min. = 28+M/2 40 (min.) 360 360 120 (max.) 360 1070 BX*(BY*) max. = X*(Y*)-70-A-M/2 Junction units LV, LH; 1000 A X*(Y*)(X*(Y*) min. = 28+M+A+130) BX*(BY*) min. = 28+M/2 BX*(BY*) max. = X*(Y*)-130-A-M/2 600 (min.) 360 360 120 (max.) 360 1010 The dimension X* min or Y* min on the side with corner covering is 460 mm. Fire resistance rating S120 Wall thickness M 20 mm (distance from wall/inside corner 30 mm A < 200 mm) BD2A-...-L... + BD2-S120-BX*(BY*)-M* 1) Junction units LL, LR A 30... 190 100 X*(Y*)(X*(Y*) min. = 18+M+A+170) BX*(BY*) min. = 18+M/2 640 (min.) 310 310 120 (max.) 310 920 BX*(BY*) max. = X*(Y*)-170-A-M/2 M 20 NSV0_01032 Junction units LV, LH; 400 A X*(Y*)(X*(Y*) min. = 18+M+A+70) BX*(BY*) min. = 18+M/2 40 (min.) 310 310 120 (max.) 310 1020 BX*(BY*) max. = X*(Y*)-70-A-M/2 1) Replace the asterisk * according to the table. Note: With other fire barrier configurations, please contact your local Siemens sales office. Junction units LV, LH; 1000 A X*(Y*)(X*(Y*) min. = 18+M+A+130) BX*(BY*) min. = 18+M/2 BX*(BY*) max. = X*(Y*)-130-A-M/2 600 (min.) 310 310 120 (max.) 310 960 The dimension X* min or Y* min on the side with corner covering is 460 mm. Siemens LV 70 2009 /99
BD2 System 160... 120 A Fire barriers Fire resistance rating S120 Wall thickness M 10 mm (distance from wall/inside corner A 200 mm) BD2C-...-L... + BD2-S120-BX*(BY*)-M* 1) Junction units LL, LR M 10 A 200 18 18 X*(Y*)(X*(Y*) min. = 370+M+A+170) BX*(BY*) min. = 370+M/2 890 (min.) 40 40 120 (max.) 40 800 Junction units LV, LH; 400 A X*(Y*)(X*(Y*) min. = 370+M+A+70) BX*(BY*) min. = 370+M/2 790 (min.) 40 40 120 (max.) 40 900 BX*(BY*) max. = X*(Y*)-170-A-M/2 BX*(BY*) max. = X*(Y*)-70-A-M/2 NSV0_01033 Junction units LV, LH; 120 A X*(Y*)(X*(Y*) min. = 370+M+A+130) BX*(BY*) min. = 370+M/2 80 (min.) 40 40 120 (max.) 40 840 BX*(BY*) max. = X*(Y*)-130-A-M/2 Fire resistance rating S120 Wall thickness M 10 mm (distance from wall/inside corner 30 mm A < 200 mm) BD2C-...-L... + BD2-S120-BX*(BY*)-M* 1) Junction units LL, LR A 30... 190 18 X*(Y*)(X*(Y*) min. = 370+M+A+170) BX*(BY*) min. = 370+M/2 720 (min.) 40 40 120 (max.) 40 970 BX*(BY*) max. = X*(Y*)-170-A-M/2 10 M 18 NSV0_01034 Junction units LV, LH; 400 A X*(Y*)(X*(Y*) min. = 370+M+A+70) BX*(BY*) min. = 370+M/2 620 (min.) 40 40 120 (max.) 40 1070 BX*(BY*) max. = X*(Y*)-70-A-M/2 Junction units LV, LH; 120 A X*(Y*)(X*(Y*) min. = 370+M+A+130) BX*(BY*) min. = 370+M/2 680 (min.) 40 40 120 (max.) 40 1010 BX*(BY*) max. = X*(Y*)-130-A-M/2 The dimension X* min or Y* min on the side with corner covering is 0 mm. 1) Replace the asterisk * according to the table. Note: With other fire barrier configurations, please contact your local Siemens sales office. /100 Siemens LV 70 2009
BD2 System 160... 120 A Installing trunking units with fire barriers Recommended minimum dimensions of ceiling or wall cut-out Fire barriers c 28 82 mm System current strength up to a 1) mm b mm 400 A 90 200 120 A 10 200 1 b a NSV0_0103 Trunking units with Tap-off unit BD2-AK1..., BD2-AK02..., BD2-AK2..., BD2-AK03..., BD2-AK3... Tap-off unit BD2-AK04..., BD2-AK0..., BD2-AK06... BD2-BWV or BD2-BDV (with or without tap-off unit) BD2.-...-EE (with or without tap-off unit) c mm 12 200 200 200 Positioning in the fire ceiling 1) For Z units depending on the lengths X*, Y*. 100 a b 1 NSV0_01036 NSV0_01037 1 Positioning in the fire wall Mounting position NSV0_01038 20 mm 1 For installing trunking units with fire barriers, the following points must be observed in addition to correct positioning: Horizontally mounted busbar lines must be supported by a fixing bracket fitted approx. 00 mm before and after the component they pass through. The space $ surrounding the busbar trunking unit within the component it passes through must be packed with mineralbased mortar or ZZ fire protection sealant TS90. The gaps between PROMATECT-H(L) panels, the busbar trunking unit and the component must be sealed with ZZ fire protection sealant TS90 (included in scope of supply if panels are required). The mortar or ZZ fire protection sealant TS90 must conform to the applicable regulations for establishing fire resistance rating or the construction of the wall or ceiling (e.g. DIN 104 and DIN 103 Part 1). The installation must be carried out according to pertinent building regulations (included in scope of supply). ZZ fire protection sealant TS90 is available from: Fa. Diederich Industrievertretung (Brandschutztechnik) Cologne Tel.: 02 21/ 9 66 2-0 Fax: 02 21 / 9 66 2-2. NSV0_01039 Siemens LV 70 2009 /101
BD2 System 160... 120 A Project planning aids Dimensional drawings Straight trunking units BD2.-.-... c Center of joint block 330 163 167 307 220 NSV0_0091a n 00 Length Number of tap-off points on both sides N L1 L2 L3 PE m n 00 0.... 1.2 1.26... 2.2 2.26... 3.2 4... 8 8... 12 On optional lengths, it may not be possible to fit tap-off units to all tap-off points N L1 L2 L3 PE 167 160... 400 A 68 NSV0_00086a 167 630... 120 A 126 Junction units L-units BD2.-...-LR-...(-G*) BD2.-...-LL-...(-G*) BD2.-...-LV-...(-G*) BD2.-...-LH-...(-G*) c G* = 8 17 y = 360 120 70 NSV0_0092 x = 360 120 G* = 8 17 70 NSV0_0093 c x = 360 120 Rated current / A c / mm 160... 400 68 630... 120 126 Z-units BD2.-...-ZR-... BD2.-...-ZL-... BD2.-...-ZV-... BD2.-...-ZH-... y = 360 120 z c c x = 360 600 y = 360 600 NSV0_0094 z = 340 120 NSV0_009 x = 360 600 y = 360 600 70 Rated current / A z / mm 160... 400 140... 120 630... 120 260... 120 /102 Siemens LV 70 2009
BD2 System 160... 120 A Project planning aids Junction units T-units BD2.-...-TR BD2.-...-TL c1 184 c 27 27 184 70 27 163 167 NSV0_0096 Rated current / A c / mm c1 / mm 160... 400 68 64 630... 120 126 122 BD2.-...-TV BD2.-...-TH 184 163 167 27 27 184 70 c1 c NSV0_0097 27 Rated current / A c / mm c1 / mm 160... 400 68 64 630... 120 126 122 Siemens LV 70 2009 /103
BD2 System 160... 120 A Project planning aids Junction units K-units BD2.-...-KRL 184 27 70 27 184 167 c1 184 c 27 27 NSV0_0098 163 Rated current / A c / mm c1 / mm 160... 400 68 64 630... 120 126 122 BD2.-...-KVH 167 27 27 70 27 NSV0_0099 184 c1 c 27 184 163 184 Rated current / A c / mm c1 / mm 160... 400 68 64 630... 120 126 122 /104 Siemens LV 70 2009
BD2 System 160... 120 A Project planning aids Junction units Flexible junction units BD2-400-R, BD2-800-R c1 c2 b c 182 Ø 6,6 1 a1 163 167 20 c3 a3 a2 a4 NSV0_00600 Type a1 a2 a3 a4 b c c1 c2 c3 BD2-400-R 120 12 187 187 79 68 64 101 0 BD2-800-R 170 786 30 20 146. 126 122 19 14 U shape c6 R NSV0_00601 Type c6 R min BD2-400-R 220 110 BD2-800-R 340 110 Z shape c6 NSV0_00602 a a6 Type a a6 c6 R min BD2-400-R 17 1000 3 110 BD2-800-R 30 190 400 110 Siemens LV 70 2009 /10
BD2 System 160... 120 A Project planning aids Distribution board feeder units BD2.-20-VE BD2.-400-VE, BD2.-1000-VE 18 8 8 c 29 4 6 Ø12, c Ø11 90 102 108, 123 28, 183, 307 NSV0_00603 163 200 NSV0_00604 c1 c2 BD2.-120-VE Enclosure cut-out 88 44 97 42 88 242 77 124 64, 84 12, 31, Enclosure cut-out a b 129 146 14 NSV0_00606 167 18 Ø 6,6 NSV0_0060a 163 200 338 112 122 Type a b c c1 c2 BD2.-20-VE 34 68 121 64 84 BD2.-400-VE BD2.-1000-VE 92 126 1, 122 142 BD2.-120-VE End feeder units BD2.-20-EE 40 64 74 143, 100 300 7 14 9 3 270 Ø9 20 163 24 270 290 200 478 63 20 NSV0_00607 /106 Siemens LV 70 2009
BD2 System 160... 120 A Project planning aids End feeder units BD2.-400-EE BD2.-1000-EE 163 40 64 10 200 40 122 12 9 0 100 423 100 8 219 39 420 440 170 304 Ø9 NSV0_00609 200 387, 60 687 14 9 NSV0_00608 BD2.-120-EE 163 86 28 366 87 611 631 40 122 128 200 200 386, 606 688 NSV0_00610b Siemens LV 70 2009 /107
BD2 System 160... 120 A Project planning aids Cabling boxes BD2-400-KR (BD2.-400-EE) BD2-1000-KR (BD2.-1000-EE) BD2-120-KR (BD2.-120-EE) 191 191 9, 190, 223 247, 223 9 NSV0_00611 308 332, 308 NSV0_00613 26, 100 100 32 481 240 28 32 370 100 473 488, 14 9 23 NSV0_00612 338 End feeder unit with switch disconnector BD2C-20-EESC, BD2C-31-EESC 0 133 Ø 9 7, 40 64 279 148, 232, 278 420 88 30 164 39 420 440 Ø 9 103 220 819 104, /108 Siemens LV 70 2009
BD2 System 160... 120 A Project planning aids End feeder units with switch disconnector BD2C-400-EESC 0,6 82,2 NSV0_01481 BD2C-630-EESC, BD2C-800-EESC 40 122 NSV0_01482 Siemens LV 70 2009 /109
BD2 System 160... 120 A Project planning aids Center feeder units BD2.-400-ME 27 40 64 40 40 163 40 624 60 73 20 686 12 90 9 1000 16 224 27 163 64 NSV0_00614 BD2.-1000-ME 27 40 122 40 40 163 783 64 680 190 40 163 12 122 9 916 936 1200 NSV0_0061 120 27 189 327 374 /110 Siemens LV 70 2009
BD2 System 160... 120 A Project planning aids Tap-off units Size 1 up to 2 A BD2-AK1/... BD2-AK1/2SD163..., BD2-AK1/3SD163..., BD2-AK1/3DK..., BD2-AK1/2T23..., BD2-AK1/3T23..., BD2-AK1/T2... BD2-AK1/2CEE163... BD2-AK1/CEE163..., BD2-AK1/CEE16... 93 199,7 126,2 7 20, NSV0_00617 144 190 170 170 170 170 c1 c2 NSV0_00618 c2 c1 NSV0_00619 c2 c1 NSV0_00620 Type c1 c2 BD2-AK1/2SD163..., BD2-AK1/3SD163..., BD2-AK1/3DK..., BD2-AK1/2T23..., BD2-AK1/3T23..., BD2-AK1/T2... 71 13 BD2-AK1/2CEE163..., BD2-AK1/CEE163... 88 44 BD2-AK1/CEE16... 106 2 Siemens LV 70 2009 /111
BD2 System 160... 120 A Project planning aids Tap-off units Size 02 up to 63 A M2 M32 M40 M63 20 101 BD2-AK02X/F... BD2-AK02X/GB... BD2-AK02X/S... 214 0 NSV0_00621 331 NSV0_00622 BD2-AK02M2/A... BD2-AK02M2/F 214 331 NSV0_00623 /112 Siemens LV 70 2009
BD2 System 160... 120 A Project planning aids Tap-off units Size 2 up to 63 A 9 0 101 20 0 34 77 NSV0_00624 M32 M40 M32 M20 BD2-AK2X/F..., BD2-AK2X/GB..., BD2-AK2X/S... 314 7 M20 20 320 NSV0_0062 BD2-AK2M2/A..., BD2-AK2M2/F 160 20 320 NSV0_00626 Siemens LV 70 2009 /113
BD2 System 160... 120 A Project planning aids Tap-off units Size 2 up to 63 A, versions with CEE, BS- CH- and Schuko socket outlets BD2-AK2M2/ CEE16FIA163 BD2-AK2X/CEE32S33 BD2-AK2M2/CEE32A323 BD2-AK2X/2CEE16S14 BD2-AK2M2/2CEE16A163 BD2-AK2X/2CEE16S27 BD2-AK2M2/T2... BD2-AK2M2/T23(T2)...CEE16... BD2-AK2M2/T23(T2)...CEE32... NSV0_00629 b1 NSV0_00628 BD2-AK2X/3BS133... Type b1 b2 BD2-AK2X/CEE32S33 98 -- BD2-AK2M2/CEE32A323 BD2-AK2M2/T23(T2)...CEE32 BD2-AK2X/2CEE16S27 86 -- BD2-AK2X/2CEE16S14 BD2-AK2M2/ CEE16FIA163 BD2-AK2M2/2CEE16A163 BD2-AK2M2/T23(T2)...CEE16 BD2-AK2M2/T2... 4 -- BD2-AK2X/3BS133... -- 4 BD2-AK2M2/2SD163CEE16A163 86 4 b2 b2 BD2-AK2M2/2SD163CEE16A163 b2 b1 NSV0_00630 NSV0_00631 BD2-AK2X/ CEE63S33 77 NSV0_00627 /114 Siemens LV 70 2009
BD2 System 160... 120 A Project planning aids Tap-off units Size 03 up to 12 A M2 M32 M40 M63 BD2-AK03X/F... BD2-AK03X/GB... BD2-AK03X/TPNR... BD2-AK03X/SPNR... 214 0 20 101 NSV0_00632 431 NSV0_00633 BD2-AK03M2/A... 160 214 431 NSV0_00634 With fuse switch-disconnector and circuit breaker BD2-AK03X/GSTA00 101 NSV0_0063 BD2-AK03X/FS... NSV0_00638 141 69 Siemens LV 70 2009 /11
BD2 System 160... 120 A Project planning aids Tap-off units Size 03 up to 12 A BD2-AK03X/LSD... 49 196 78 20 6 7 NSV0_00680b Size 3 up to 12 A BD2-AK3X/GS00 BD2-AK3X/GB... 0 474 434 7 20 9 20 0 101 NSV0_00639 M32 M63 M40 M2 M20 440 With fuse switch-disconnector BD2-AK3X/GSTZ00 R 17 60 NSV0_00640 /116 Siemens LV 70 2009
BD2 System 160... 120 A Project planning aids Tap-off units Size 04 up to 20 A BD2-AK04/LSD... 336 260 202 494 NSV0_01040 406 ca. 340 72 662 BD2-AK04/LSM... 278 202 NSV0_01041 271 348 ca. 370 BD2-AK04/SNH1, BD2-AK04/GB20J-... BD2-AK04/FS... 278 202 NSV0_01042 339 263 202 NSV0_01043 Siemens LV 70 2009 /117
BD2 System 160... 120 A Project planning aids Tap-off units Size 0, 06 up to 630 A BD2-AK0/LSD..., BD2-AK06/LSD... 406 408 332 22 494 ca. 410 NSV0_01044 862 924 941 BD2-AK0/LSM..., BD2-AK06/LSM... 390 328 22 312 ca. 400 NSV0_01047 BD2-AK0/SNH2, BD2-AK06/SNH3, BD2-AK/GB...R1003 BD2-AK0/FS... 328 22 389 313 22 NSV0_01048 NSV0_01049 /118 Siemens LV 70 2009
BD2 System 160... 120 A Project planning aids Ancillary equipment units 4 h 10 1 NSV0_00646 77 Type BD2-GKM2/F BD2-GKX/F h 101 11 BD2-GKM2/F NSV0_00647 160 20 320 BD2-GKX/F NSV0_00648 20 320 Siemens LV 70 2009 /119
BD2 System 160... 120 A Project planning aids Protective sleeves Fire barriers BD2-400-D BD2-120-D +BD2-S90 (S120)-... NSV0_00649 208 NSV0_0060 208 NSV0_0062 64 NSV0_0063 107 163 110 168 BD2.-160 (-20, -400) -... 20 BD2-...-D NSV0_0061 208 NSV0_0064 122 16 NSV0_006 00 163 BD2.-630 (-800, -1000, -120) -... 20 Joint blocks BD2-400-SK, BD2-120-EK End flanges BD2-400-FE, BD2-120-FE NSV0_0066 330 140 a Ø 6,6 Type BD2-400-SK BD2-120-EK a mm 68 126 1 16 c Type c mm BD2-400-FE 68 BD2-120-FE 126 80 167 167 1 2 NSV0_0067 2 Length of trunking unit End of end flange = center of joint block /120 Siemens LV 70 2009
11 BD2 System 160... 120 A Fixing Fixing brackets, flat and edgewise Spacer Spacer bracket BD2-400-BB, BD2-120-BB BD2-DSB BD2-BD Project planning aids NSV0_0068 1 c 33 c1 NSV0_0069 30... 82 110 11 169 199 100 7,2 7,2 Type c mm BD2-400-BB 86, BD2-120-BB 144, 34 c1 mm 48 77 11 33 26 2 40 NSV0_00660 288 20 208 100 14 9 28 To secure systems directly to concrete walls, always use steel expansion bolts approved by the local building inspectorate. For example: RICO, Order No. 1J1-A08/40 Fischerwerke, type SLM8N, article no. 021 Vertical retaining element BD2-BWV 16 246 200 Vertical retaining element BD2-BDV NSV0_00662 28 82 91 2 9 1 48 +10-13 400 +10 - NSV0_00661 27 43 600 640 1 Vertical fixing bracket BD2-BVF 230 200 9 16 40 NSV0_00663 NSV0_00664 16 140 140 11 Siemens LV 70 2009 /121
BD2 System 160... 120 A Project planning aids Protective covers according to IP4 Edgewise mounting position Vertical mounting position BD2-400-HF, BD2-120-HF BD2-400-HFE, BD2-120-HFE BD2-400-VF, BD2-120-VF 362 b 16 182 b NSV0_00666 16 16 212 b NSV0_00667 NSV0_0066 Type b mm BD2-400-HFE 72 BD2-120-HFE 130 Type b mm BD2-400-VF 72 BD2-120-VF 130 Type b mm BD2-400-HF 72 BD2-120-HF 130 Flat mounting position Flat and vertical mounting position BD2-FF BD2-FFE BD2-FAS 364 170 NSV0_00669 17, 183 166 NSV0_00668 NSV0_00670 19 122 17, 170 /122 Siemens LV 70 2009
BD2 System 160... 120 A Project planning aids Protective covers according to IP For connection point or end flange BD2-400-FS, BD2-120-FS, BD2-400-FSE, BD2-120-FSE b a NSV0_00676 170 178 190 Type BD2-400-FS a 72 b 37 BD2-120-FS 130 66 BD2-400-FSE 72 37 10 10 368 BD2-120-FSE 130 66 For tap-off units BD2-AK1-IP 70, 120 110, 3 10 166 NSV0_00677 BD2-AK02-IP, BD2-AK03-IP 120 Ø1 10 166 NSV0_00678 Ø4 Ø7 BD2-AK2X-IP, BD2-AK3X-IP Ø 4 Ø 1 10 Ø 4 Ø 7 X Ø 4 NSV0_00679 View X Type BD2-AK2X-IP a 130 16 10 166 BD2-AK3X-IP 190 9 a 120 Siemens LV 70 2009 /123
BD2 System 160... 120 A Project planning aids Socket outlets including accessories Socket outlets with adapter enclosure BD2-CEE 7 7 40 l1 l2 BD2-SD163 7 NSV0_00672 NSV0_00671 7 1 69 Adapter enclosure BD2-AG 26 7 60 7 M2 NSV0_00673 1 4,4 60 7 R 6 3 10 40 Adapter plate BD2-APM BD2-APO 44 NSV0_0067 3, 38 60 7 7 38 60,3 R 6 NSV0_00674 7 7 /124 Siemens LV 70 2009
Appendix 6 6/2 Glossary 6/6 Ordering notes 6/7 Further documentation 6/8 Standards and approvals 6/11 Siemens contacts 6/12 Online services 6/13 Customer support 6/14 Subject index 6/1 Type reference list 6/16 Order number index 6/17 Terms of sale and delivery Export regulations Siemens LV 70 2009
Appendix Glossary 6 Overview This glossary offers brief explanations of some of the terms used in this catalog. However it must not be regarded as a substitute for the actual text of the standard, especially where the new terms used in IEC/EN 60947 are concerned. (AC) Rating or rated power (see also IEC/EN 60947-1; 4.3.2.3) Altitude Ambient temperature, enclosed (see also IEV 441-11-13) Ambient temperature, open (see also IEV 441-11-13) Back-of-hand proof Clearance in air (see also IEC/EN 60947-1; 2..46/IEV 441-17-31) Closing delay Conventional free air thermal current I th (see also IEC/EN 60947-1; 4.3.2.1) Control circuit reliability Creepage distance (see also IEC/EN 60947-1; 2..1/IEV 11-03-37) Damp heat, constant Damp heat, cyclical Reference is made underneath each term to the relevant section in the standard, e.g. IEC/EN 60947-1. Additionally, IEV numbers are stated in order to enable you to find foreign language equivalents in the electrotechnical dictionary (IEC 0: International Electrotechnical Vocabulary), e.g. IEV 441-17-31. The operational power that an equipment is capable of switching at the associated rated operational voltage in accordance with the utilization category, e.g. contactor utilization category AC-3: 37 kw at 400 V. The density of air decreases with increasing altitude, and this reduces its insulating capacity as well as its heat transfer capability. The rated operational voltage and rated operational current of switching devices, conductors and motors as well as the tripping behavior of thermal overload relays are affected by this. Upon request, Siemens will supply information as to the suitability or otherwise of switchgear for operation at altitudes above the 2000 m limit specified by the standard. or get in direct touch with Technical Assistance (see page 6/13). Temperature at which the switching device is capable of being operated within a closed enclosure. For this purpose, it must be taken into account that the power losses of the device will add to the internal temperature rise within the enclosure. Room temperature (for example of the workshop or contact chamber) in which the switching device is located. An equipment whose live parts cannot be touched by a sphere of 0 mm diameter is regarded as back-of-hand proof. The distance between two conductive parts along a string stretched the shortest way between these conductive parts. The clearance in air is determined by the rated impulse withstand voltage, overvoltage category and the degree of pollution. The interval of time between the instant of command and the first make operation of the contacts of the first pole to close. The closing delay is made up of the response delay and the closing delay. The maximum value of current that an equipment is capable of carrying for a minimum of 8 hours without thermal overloading. As a rule, it corresponds to the maximum rated operational current. Measures the probability of switching states arising during the endurance of a switching contact that would be interpreted as faults by downstream electronic controllers (PLCs). Control circuit reliability is expressed in values based on tests using standard limit values for signals according to IEC/EN 61131-2. The shortest distance along the surface of the insulating material between two conductive parts. The creepage distance is determined by the rated insulation voltage, the degree of pollution and the creep resistance CTI of the material used. This test subjects the equipment to an ambient temperature of 40 C at a constant humidity of 93 %. At set intervals during the test, the electrical and mechanical function of the equipment are examined. This test subjects the equipment to cyclically changing climatic conditions. A cycle applies 40 C ambient temperature at 93% relative humidity for 12 hours, followed by 12 hours of 2 C at 9%. At set intervals during the test, the electrical and mechanical function of the equipment are examined. 6/2 Siemens LV 70 2009
Appendix Glossary Degree of pollution (see also IEC/EN 60947-1;..8) EMERGENCY-STOP switching device Finger-safe Isolating function (see also IEC/EN 60947-1; 2.1.19) Losses (see also IEV 11-03-18) Mechanical shock resistance Minimum command duration Opening time (see also IEV 441-17-36) Overvoltage category (see also IEC/EN 60947-1; 2..60) Positive opening (see also IEC/EN 60947-1; 2.4.10 / IEV 441-16-11) Positive or enforced operation/actuation Ident. No. for the prospective quantities of conductive dust and humidity, which can lead to a reduction in the control circuit reliability of a switching device. The degree of pollution is defined by the following factors: Degree of pollution 1: No pollution or only dry, non-conductive pollution occurs. The pollution has no effect on the control circuit reliability. Degree of pollution 2: Usually, only non-conductive pollution. However, transient conductivity through condensation is to be expected. Degree of pollution 3: (switchgear for industrial use) Conductive pollution or dry, non-conductive pollution, which is rendered conductive through condensation. Degree of pollution 4: The pollution leads to long-term conductivity, e.g. pollution through conductive dust, rain or snow. Switching device with an EMERGENCY-STOP device that is intended to prevent danger to persons, damage to machinery or work materials. An equipment whose live parts cannot be touched by the operator during actuation is termed finger-safe. This also affects operator activity on neighboring switching devices. The finger-safe area of a push-actuated operating medium is a circular area of at least 30 mm radius around the actuator, and vertical to the direction of actuation. Within this circular area, touch-critical parts must be located at not less than 80 mm below the actuating level. Equipment is deemed to possess this isolating function provided their switching contacts, when in the open position, achieve the separation distance prescribed for the isolation of electrical circuits, and their clearance and creepage distances are of the required size. The power supply to the entire installation or a section of the installation can thus be cut off for safety reasons, e.g. during maintenance. The difference between the input power and the output power of a device. The main type of loss in electrical equipment and operating media in power distribution is current heat loss. The capacity of an equipment to withstand pulse-like motions without changing its operating state or sustaining damage. No contact lifting must take place on devices in the On position, the main contacts must not knock against one another in the Off position. A protective switch must not trip, and auxiliary switches must not change their switching state. Minimum period of time for which a trip-initiating factor (control pulse, short-circuit current) must be present in order to effect the corresponding reaction, e.g. the short-circuit duration necessary to initiate tripping. The interval of time between the specified instant of initiation of the opening operation and the instant when the arcing contacts have separated in all poles. The opening time is the sum of the tripping time and the inherent delay of the contacts. Ident. No. for prospective overvoltages as might be caused, for example, as a result of lightning or switching operation. The overvoltage category applicable to industrial switchgear is III. The applicability of switchgear according to the overvoltage categories is as follows: Overvoltage category IV: Use directly at the termination point of the installation (directly affected by any lightning), e.g. at an overhead line connection point. Overvoltage category III: Operating media with special requirements as to the serviceability for connection in fixed installations which are protected by overvoltage diversion measures, e.g. switches in low-voltage distribution systems or in control systems for industrial use. Overvoltage category II: Power consumers for connection to fixed installations, e.g. household appliances, electrical tools. Overvoltage category I: Operating media for connection to circuits with overvoltage protective devices, e.g. electronic devices. An opening operation which ensures that the main contacts of a switching device have attained the open position when the actuator is in the Off position. This describes an arrangement where a link between the actuator and the contact ensures that the force exerted on the actuator is transferred directly (without the intervention of sprung parts) onto the contact. 6 Siemens LV 70 2009 6/3
Appendix Glossary 6 Positively-driven operation (see also IEC/EN 60947-1; 2.4.11 / IEV 441-16-12) Rated actuating voltage U c (see also IEC/EN 60947-1; 4..1) Rated breaking capacity (see also IEC/EN 60947-1; 4.3..3) Rated conditional short-circuit current I q (see also IEC/EN 60947-1; 2..29/IEV 441-17-20) Rated control supply voltage U s (see also IEC/EN 60947-1; 4..1) Rated current I n (of a circuit breaker) (see also IEC/EN 60947-2; 4.3.2.3) Rated frequency (see also IEC/EN 60947-1; 4.3.3) Rated impulse withstand voltage U imp (see also IEC/EN 60947-1; 4.3.1.3) Rated insulation voltage U i (see also IEC/EN 60947-1; 4.3.1.2) Rated making capacity (see also IEC/EN 60947-1; 4.3..2) Rated operational current I e (see also IEC/EN 60947-1; 4.3.2.3) Rated operational voltage U e (see also IEC/EN 60947-1; 4.3.1.1) Rated power (see also IEC/EN 60947-1; 4.3.2.3) Rated service short-circuit breaking capacity I cs (see also IEC/EN 60947-2; 4.3..2.2) Rated short-circuit breaking capacity I cn (see also IEC/EN 60947-1; 4.3.6.3) Rated short-circuit making capacity I cm (see also IEC/EN 60947-1; 4.3.6.2) This ensures that the auxiliary contacts of a switching device are always in the switch position corresponding to the open or closed position of the main contacts. The contacts of contactors are positively driven contacts, provided they are mechanically linked in such a way as to ensure that normally closed contacts and normally open contacts can never be closed simultaneously. This arrangement must also ensure that minimum contact separation of 0. mm is maintained over the entire endurance of the device, even during a fault (e.g. welding of one contact). The pertinent German Trade Association requires the use of contactors with positively driven contacts for control systems on power presses in the metal processing industry. The voltage which is applied to the actuating make contact in a control circuit. Due to the presence in the control circuit of transformers or resistors, this voltage may differ from the rated control supply voltage. The rms value that a switching device is capable of breaking according to its utilization category. This value refers to the rated operational voltage and the rated operational current. Equipment must be capable of breaking any value of current up to and including its rated breaking capacity stated. The short-circuit current that a switching device, e.g. a circuit breaker, protected by a short-circuit protective device such as a motor-protective circuit breaker, can carry for the duration of the tripping delay of the protective mechanism. The voltage applied to the input terminals of the control circuit of an equipment. Due to the presence in the control circuit of transformers or resistors, this voltage may differ from the rated actuating (control circuit) voltage. For circuit breakers, this current value is equal to the rated uninterrupted current and the conventional free-air thermal current. The frequency for which an equipment is designed and to which the other characteristics are referred. Measures the stability of the internal clearances of an equipment against overvoltage peaks. The utilization of suitable switchgear can ensure that overvoltages are prevented from transferring from the mains to de-energized system components within it. The voltage to which insulation tests and creepage distances of equipment are referred. The maximum rated operational voltage must not be higher than the rated insulation voltage. The value of current that an equipment is capable of switching on in accordance with the utilization category and the rated operational voltage. The current that an equipment is capable of carrying, taking into account the rated operational voltage, duration of operation, utilization category and ambient temperature. The voltage to which the characteristics of an equipment are referred. The highest rated operational voltage must not be higher than the rated insulation voltage. The power output of a motor at the associated rated operational voltage. The prospective short-circuit current which, depending on the rated operational voltage, a circuit breaker is capable of breaking repeatedly (test cycle O-CO-CO, previously P-2). After interrupting this shortcircuit current value, the circuit breaker must be capable of continuing to carry and disconnect in the event of overloading, the rated uninterrupted current, despite its own thermal level having increased. The maximum value of current that an equipment is capable of switching off at rated operational voltage and rated frequency, and without sustaining damage. It is expressed as rms value. The maximum value of current that an equipment is capable of switching on at rated operational voltage and rated frequency, and without sustaining damage. Unlike for other characteristic values, it is expressed as maximum prospective peak value. 6/4 Siemens LV 70 2009
Appendix Glossary Rated short-time withstand current I cw (see also IEC/EN 60947-1; 4.3.6.1) Rated ultimate short-circuit breaking capacity I cu (see also IEC/EN 60947-2; 4.3..2.1) Rated uninterrupted current I u (see also IEC/EN 60947-1; 4.3.2.4) Safe isolation (see also IEC/EN 61140) Tamper proof Touch protection Type of coordination Utilization category (see also IEC/EN 60947-1; 2.1.18/IEV 441-17-19) (see also IEC/EN 60947-2; 4.4) The short-time withstand current value that the equipment is capable of carrying for a specified time without damage, e.g. due to excessive heating. Maximum short-circuit current which a circuit breaker is capable of interrupting (test cycle: O.-CO, previously P-1). Following short-circuit switching off, the circuit breaker is able, in the event of overload, to trip with increased tolerances. The value of current that an equipment can carry in uninterrupted duty (for weeks, months or years). Isolation of circuits not carrying hazardous voltages, e.g. protective extra-low voltage, from circuits in which hazardous voltages flow. Such isolation is achieved by means of reinforced or double insulation, which reliably prevents voltage transfer from one circuit to another. This might otherwise take place between main circuits and auxiliary circuits in switching devices or between primary and secondary in safety transformers. Safe isolation is a priority requirement for safety circuits and functional low-voltage circuits. An Emergency-Stop switching device is regarded as tamper proof provided it cannot be reset without tools or via prescribed procedure, after tripping has taken place. The device latches in the tripped position. Accidental or deliberate manipulation (inching) is ruled out. Design measures incorporated into equipment in order to prevent direct contact (i.e. without tools) with live parts of a system (finger-safe, back-of-hand proof). Status of a controlgear combination (motor starter) during and after testing at rated conditional short-circuit current: Type of coordination "1": - no risk to persons or installations - no requirement for immediate readiness for renewed operation - damage to the starter is admissible Type of coordination "2": - no risk to persons or installations - starter is capable of renewed operation - no damage to the starter with the exception of a slight welding of the switching contacts, provided they can be separated without significant deformation A combination of specified requirements relating to the operating condition in which the switching device or fuse fulfills its purpose, selected to represent a characteristic group of practical applications. The specified requirements may concern, for example, the values of making capacity, breaking capacity and other characteristic values, data concerning associated circuits, and the relevant conditions of use and operation characteristic. For circuit breakers, the utilization category denotes whether the equipment is designed for selectivity using time delay (category B) or not (category A). Symbols used in technical data and formulae OP ON period (duty factor) I T Response value of earth-fault release I Δn Response value of earth-fault release I th Conventional free air thermal current I cm Rated short-circuit making capacity I the Conventional enclosed thermal current I cn Rated short-circuit breaking capacity I u Rated uninterrupted current I cs Rated service short-circuit breaking capacity S NT Transformer rating I cu Rated ultimate short-circuit breaking capacity t r Delay time of overload release response I cw Rated short-time withstand current t T Delay time of earth-fault release response I e Rated operational current t v Delay time of short-circuit release response i Transformer initial short-circuit current I rmf Response value of fixed, instantaneous short-circuit release I L Response value for load monitoring I rmv Response value of short-time delayed short-circuit release I n Rated current U c Rated actuating voltage I NT Rated transformer current U e Rated operational voltage I PK Rated peak withstand current U i Rated insulation voltage I q Rated conditional short-circuit current U im Rated impulse withstand voltage I r Set value of overcurrent release u k Transformer short-circuit voltage I rm Response value of instantaneous short-circuit release U s Rated control supply voltage 6 Siemens LV 70 2009 6/
Appendix Ordering notes Aluminum (Al) and copper (Cu) surcharges Surcharges for aluminum (Al) and copper (Cu) will be added to the prices of certain products. Calculation of the surcharges will be governed by the official Al quotation for aluminum and by the Cu-DEL quotation applying on the date of receipt of order or of call-off. The prices for products in this catalog include the price of aluminum and copper calculated on the basis of a list price of 10/100 kg. If the aluminum and copper rates exceed this price, a surcharge will be made on the basis of the DEL quotation in force on the day of delivery. Equation for calculating Al and Cu surcharges: Cu-DEL quotation or Al quotation 10 ----------------------------------------------------------- Cu/Al weight (kg) 100 kg The quotations for copper and aluminum can be consulted daily on the Internet: http://www.kabelverband.org See the "Aktuelle Metall-Notierungen" there, then: "KUPFER DEL Notiz hoch" (copper) "ALU in Kabeln" (aluminium) Small orders When small orders are placed, the costs associated with order processing are greater than the order value. We recommend therefore that you combine several small orders. Where this is not possible, we unfortunately have to charge a processing supplement of 20.-- to cover our costs for order processing and invoicing for all orders with a net goods value of less than 20.--. Selection and ordering data The order number and the type designation must be quoted in all orders. Order No. When ordering the busbar trunking systems BD01 and BD2, the prefix BVP: must be placed before the article number listed in the catalog, for example: BVP:034262. Type If a type designation contains * characters, it is not complete (e.g. in case of variable lengths) and must be supplemented according to specifications in the table. In this case, the order number is not unique. 6 6/6 Siemens LV 70 2009
Appendix Further documentation Overview You will find all the latest information material, such as brochures, catalogs, manuals and operating instructions on lowvoltage controls and distribution on the Internet at: http://www.siemens.com/lowvoltage/info Here you can order your copy of the available documentation or download it in common file formats (PDF, ZIP). We regard product support as just as important as the products and systems themselves. Visit our Support site on the Internet for a comprehensive range of material on SIRIUS, SENTRON and SIVACON, such as Catalogs available to order free of charge Operating instructions and manuals for direct download Online registration for seminars and events Up-to-date answers to your queries and problems Software upgrades and updates for fast download Telephone assistance in more than 190 countries Photos and graphics for external use and much, much more all conveniently and easily accessible. For your inventory control and configuration systems we can provide commercial, technical and graphic data in electronic form for the range of low-voltage control products: We also provide further support for SIRIUS - SENTRON - SIVACON Technical Product Data for CAx Applications Edition 07/2008 The DVD provides low-voltage control products for further processing in CAE/CAD systems: Technical product master data in CSV and Excel format Graphic product data - 2D dimensional and isometric drawings in DXF and DWG format - 3D models in STEP format Product data sheets as PDF files in the languages: -English - French -German - Spanish Texts for tenders in GAEB and Text format. Order No.: E86060-D1000-A207-A6-6300 Token fee 10.-- Brochures, catalogs and CDs offer fast and more in-depth information 6 Siemens LV 70 2009 6/7
Appendix Standards and approvals Overview Approvals, test certificates, characteristic curves An overview of the certificates available for low-voltage control products along with more technical documentation can be consulted daily on the Internet at: http://www.siemens.com/lowvoltage/support Product support: Approvals / Certificates Product support: Characteristic curves Approval requirements valid in different countries Siemens low-voltage switchgear and systems are designed, manufactured and tested according to the relevant German standards (DIN and VDE), IEC publications and European standards, as well as CSA and UL standards. The standards assigned to the single devices are stated in the relevant chapters of this catalog. As far as is economically viable, the requirements of the various regulations valid in other countries are also taken into account in the standard version of the equipment. Some countries have approval requirements for certain low-voltage devices. Depending on market demands, approvals for the devices have been obtained or are under application from the authorized testing authorities (see the table on page 6/9). In some cases, CSA for Canada and UL for the USA only approve special switchgear designs. For this equipment, partial limitations of the maximum permissible voltages, currents and ratings can be imposed, or special approvals and, in some cases, special identification is required. In some European countries approval is required for installation material. The equipment group "miniature circuit breakers and RCCBs" may still be marked in certain fields and therefore bears the corresponding marks of approval. (See the table on page 6/9.) For use on board ship, the specifications of the marine classification societies must be observed. In some cases, they require type tests of the components to be approved. (See the table on page 6/9.) 6 6/8 Siemens LV 70 2009
Appendix Standards and approvals Testing bodies, approval identification and approval requirements Country Canada 1) USA 1) China Austria Belgium France Germany Switzerland Government-appointed or private, officially recognized testing bodies CSA UL (USA) UL CQC ÖVE CEBEC UTE VDE SEV Approval symbol s cu cu u U cuus cuus V cuus cuus Approval requirements Remarks 2) 2) CCC Approval requirements only for installation material 1) For guide numbers and file numbers for approvals, please visit www.siemens.com/automation/support and select "Product Support". 2) UL and CSA are authorized to grant approvals according to Canadian or US regulations. Please note: these approvals are frequently not recognized and additional approval often has to be obtained from the national testing authority. Marine classification societies Country Germany France Great Britain Italy Norway Poland Russia, CIS USA Name Germanischer Lloyd Bureau Veritas Lloyds Register of Shipping Registro Italiano Navale Det Norske Veritas Polski Rejestre Statków Russian Maritime Register of Shipping Codes GL BV LRS RINA DNV PRS RMRS ABS American Bureau of Shipping > Designations Manufacturers of products which fall within the subject area to which EC directives apply must identify their products, operating instructions or packaging with a CE mark of conformity. The CE mark of conformity confirms that a product fulfills the appropriate basic requirements of all pertinent directives. The mark of conformity is a mandatory requirement for putting products into circulation throughout the EU. Special standards for the USA and Canada In the USA and Canada, for machine tools and processing machines in particular, supply lines are laid using rubber insulated cable enclosed in heavy-duty steel piping similar to that used for gas or water pipe systems. The tubing system must be completely watertight and electrically conductive (especially sleeving and elbows). Since the tubing system can also be grounded, the cable entries of enclosed units equipped with heavy-gauge or metric threads must be fitted with metal adapters between these threads and the tube thread. The necessary adapters are specified for the switchgear as accessories; they should be ordered separately unless otherwise specified. Low-voltage control circuit devices (e. g. contactor relays, commanding and signaling devices and auxiliary switches/auxiliary Different features of UL approvals (for USA and Canada) All the products in this catalog are in conformance with the EEC directives and bear the CE mark of conformity. Low Voltage Directive (73/23/EEC). EMC Directive (89/336/EEC) contacts in general) are generally only approved by CSA and UL for "Heavy Duty" or "Standard Duty" and are identified either with these specifications in addition to the maximum permissible voltage or by using an abbreviation. The abbreviations are harmonized with IEC 60947--1 Appendix 1 Table A1 and correspond to the stated utilization categories. For various switching devices detailed in the catalog, a note has been included to the effect that, above a certain voltage, the auxiliary switches/auxiliary contacts can only be used if they have the same polarity. This means that the input terminals can only be connected to the same pole of the control voltage, e.g. "600 V AC above 300 V AC same polarity". Recognized Component Listed Product UL issues yellow "Guide cards" with a Guide No. and a File No. UL issues white "Guide cards" with a Guide No. and a File No. Devices are identified on the rating plate Devices are identified using the "UL listing mark" on the rating plate using the "UL recognition mark": e. g. USA: u LISTED 16 C Canada: cu LISTED 16 C USA: U, cuus IND. CONT. EQ. IND. CONT. EQ. Canada: cu, cuus (16 C stands for: Siemens, I IA CD Division, Amberg plant) Devices are approved as modules for "factory wiring", i.e.: as devices for installation in control systems, which are selected, installed, wired and tested entirely by trained personnel in factories, workshops or elsewhere, according to the operating conditions. Devices are approved for "field wiring", i.e.: As devices for installation in control systems, which are completely wired by trained personnel in factories, workshops or elsewhere. As single devices for sale in retail outlets in the USA/Canada. If devices are u or cu approved as "listed products", they are also approved as U or cu "recognized components". 6 Siemens LV 70 2009 6/9
Appendix Standards and approvals Special standards in different countries Argentina In Argentina the approval requirements are based on Resolution 92/98. Since 01.04.2001 circuit breakers and RCCBs require approval. Since 01.04.2002 protective switches up to I n =63A and U max = 440 V require approval and must bear a mark of conformity. CCC approval for China A003617 Since August 1, 2003, CCC approval is required for all products that are marketed in China. GOST approval for Russia A GOST approval is required for all products sold in Russia. The GOST mark has been obligatory on the packaging of all devices since mid- 1998. All devices delivered to any part of the Russian Federation must have this customs certification. South Africa In South Africa there are approval requirements for circuit breakers and busbar trunking systems. Such equipment must bear a conformity mark. Romania In Romania, components which are used in public buildings must be approved by the Romanian testing authority ICECON. Country-specific approvals Country Canada USA Romania Russia 1), CIS Turkey Ukraine China South Africa Codes CSA UL ICECON GOST-R TSE Ukraine- CCC SABS GOST Busbar trunking systems CD-L System -- -- -- On request -- On request On request -- BD01 system -- -- -- -- BD2 system -- -- -- -- LD system -- -- -- -- -- LX system -- -- -- -- -- -- LR system -- -- -- -- -- -- = approved or certified 1) In Russia, the BD2, LD and LX systems also passed the fire barrier test (Poshtest). Approvals issued by marine classification societies Country Germany France Great Britain Italy Norway Poland Russia, CIS USA Name Germanischer Lloyd Bureau Veritas Lloyds Register of Shipping Registro Italiano Navale Det Norske Veritas Polski Rejestre Statków Russian Maritime Register of Shipping Codes GL BV LRS RINA DNV PRS RMRS ABS Busbar trunking systems CD-L System -- -- -- -- On request -- -- -- BD01 system -- -- -- -- -- -- BD2 system -- -- -- -- -- -- LD system -- -- -- -- -- -- LX system -- -- -- -- -- -- -- -- LR system -- -- -- -- -- -- -- -- = approved or certified American Bureau of Shipping 6 More information For more information about standards and approvals go to http://www.siemens.com/automation/support and select "Product Support". If you have any questions concerning UL/CSA approvals, contact Technical Assistance, Tel.: +49 (911) 89-900. 6/10 Siemens LV 70 2009
Appendix Siemens Contacts Siemens Contacts Worldwide At http://www.siemens.com/automation/partner you can find details of Siemens contact partners worldwide responsible for particular technologies. You can obtain in most cases a contact partner for Technical Support, Spare parts/repairs, Service, Training, Sales or Consultation/engineering. You start by selecting a Country, Product or Sector. By further specifying the remaining criteria you will find exactly the right contact partner with his/her respective expertise. 6 Siemens LV 70 2009 6/11
Appendix Online Services Siemens Industry Automation and Drive Technologies in the WWW A detailed knowledge of the range of products and services available is essential when planning and configuring automation systems. It goes without saying that this information must always be fully up-to-date. Siemens Industry Automation and Drive Technologies has therefore built up a comprehensive range of information in the World Wide Web, which offers quick and easy access to all data required. Under the address http://www.siemens.com/automation you will find everything you need to know about products, systems and services. Product Selection Using the Offline Mall Detailed information together with convenient interactive functions: The Offline Mall CA 01 covers more than 80,000 products and thus provides a full summary of the Siemens Automation and Drives product base. Here you will find everything that you need to solve tasks in the fields of automation, switchgear, installation and drives. All information is linked into a user interface which is easy to work with and intuitive. After selecting the product of your choice you can order at the press of a button, by fax or by online link. Information on the Offline Mall CA 01 can be found in the Internet under http://www.siemens.com/automation/ca01 or on CD-ROM or DVD. 6 Easy Shopping with the A&D Mall The A&D Mall is the virtual department store of Siemens AG in the Internet. Here you have access to a huge range of products presented in electronic catalogs in an informative and attractive way. Data transfer via EDIFACT allows the whole procedure from selection through ordering to tracking of the order to be carried out online via the Internet. Numerous functions are available to support you. For example, powerful search functions make it easy to find the required products, which can be immediately checked for availability. Customer-specific discounts and preparation of quotes can be carried out online as well as order tracking and tracing. Please visit the A&D Mall on the Internet under: http://www.siemens.com/automation/mall 6/12 Siemens LV 70 2009
Appendix Customer Support Our Services for Every Phase of Your Project Configuration and software engineering Support in configuring and developing with customer-oriented services from actual configuration to implementation of the automation project. 2).I In the face of harsh competition you need optimum conditions to keep ahead all the time: A strong starting position. A sophisticated strategy and team for the necessary support - in every phase. Service & Support from Siemens provides this support with a complete range of different services for automation and drives. In every phase: from planning and startup to maintenance and upgrading. Our specialists know when and where to act to keep the productivity and cost-effectiveness of your system running in top form. Online Support Technical Consulting Technical Assistance The comprehensive information system available round the clock via Internet ranging from Product Support and Service & Support services to Support Tools in the Shop. http://www.siemens.com/ automation/service&support Support in the planning and designing of your project from detailed actual-state analysis, target definition and consulting on product and system questions right to the creation of the automation solution. 2) Expert technical assistance 1) for Low-voltage controls and electrical installation. Tel.: +49 (9 11) 8 9-9 00 Fax: +49 (9 11) 8 9-9 07 E-Mail: technical-assistance @siemens.com Technical Support Service on Site Repairs and Spare Parts Optimization and Upgrading Competent consulting in technical questions covering a wide range of customer-oriented services for all our products and systems. Tel.: +49 (0)180 0 0 222 Fax: +49 (0)180 0 0 223 (0.14 /min. from a German landline network, mobile telephone prices may vary) http://www.siemens.com/ automation/support-request With Service On Site we offer services for startup and maintenance, essential for ensuring system availability. In Germany 0180 0 0 444 2) (0.14 /min. from a German landline network, mobile telephone prices may vary) In the operating phase of a machine or automation system we provide a comprehensive repair and spare parts service ensuring the highest degree of operating safety and reliability. In Germany 0180 0 0 446 1) (0.14 /min. from a German landline network, mobile telephone prices may vary) To enhance productivity and save costs in your project we offer high-quality services in optimization and upgrading. 2) 6 1) Contact: Technical assistance for product selection Old/new coding Competitor coding Special versions Special requirements Sales promotion (Infoline). Your regional contacts for sales support (prices, discounts, delivery times). Technical Support for commissioning support and after-sales services. 2) For country-specific telephone numbers go to our Internet site at: http://www.siemens.com/automation/service&support Siemens LV 70 2009 6/13