Agilent 2-Port and 4-Port PNA-X Network Analyzer N5244A - MHz to 43.5 GHz N5245A - MHz to 5. GHz with Option H29 Data Sheet and Technical Specifications
Documentation Warranty THE MATERIAL CONTAINED IN THIS DOCUMENT IS PROVIDED "AS IS," AND IS SUBJECT TO BEING CHANGED, WITHOUT NOTICE, IN FUTURE EDITIONS. FURTHER, TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, AGILENT DISCLAIMS ALL WARRANTIES, EITHER EXPRESS OR IMPLIED WITH REGARD TO THIS MANUAL AND ANY INFORMATION CONTAINED HEREIN, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. AGILENT SHALL NOT BE LIABLE FOR ERRORS OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IN CONNECTION WITH THE FURNISHING, USE, OR PERFORMANCE OF THIS DOCUMENT OR ANY INFORMATION CONTAINED HEREIN. SHOULD AGILENT AND THE USER HAVE A SEPARATE WRITTEN AGREEMENT WITH WARRANTY TERMS COVERING THE MATERIAL IN THIS DOCUMENT THAT CONFLICT WITH THESE TERMS, THE WARRANTY TERMS IN THE SEPARATE AGREEMENT WILL CONTROL. DFARS/Restricted Rights Notice If software is for use in the performance of a U.S. Government prime contract or subcontract, Software is delivered and licensed as Commercial computer software as defined in DFAR 252.227-74 (June 995), or as a commercial item as defined in FAR 2.(a) or as Restricted computer software as defined in FAR 52.227-9 (June 987) or any equivalent agency regulation or contract clause. Use, duplication or disclosure of Software is subject to Agilent Technologies standard commercial license terms, and non-dod Departments and Agencies of the U.S. Government will receive no greater than Restricted Rights as defined in FAR 52.227-9(c)(-2) (June 987). U.S. Government users will receive no greater than Limited Rights as defined in FAR 52.227-4 (June 987) or DFAR 252.227-75 (b)(2) (November 995), as applicable in any technical data.
Definitions... 4 Specifications: N5244A and N5245A Option H29... 5 Corrected System Performance with 3.5mm Connectors... 5 Table. 8556A Calibration Kit... 5 Table 2. N4693A 2- Port Electronic Calibration Module... 9 Uncorrected System Performance, N5244A and N5245A Option H29... 3 Noise Error Terms: N5244A and N5245A Option H29... 3 Table 3. Noise State Directivity, Port and Port 2 (db)... 3 Table 4. Noise State Load Match, Port (db)... 4 Table 6. Noise State Reflection Tracking (S and S22), Min/Max (db)... 6 Table 7. Noise State Transmission Tracking, Min/Max (db)... 6 Table 8. Noise State Source Match, Port (db)... 7 Table 9. Noise State Source Match, Port 2 (db)... 8 Test Port Input: Option H29... 9 Table. Receiver Noise Figure, Port 2 (db)... 9 Table. Noise Jitter,2 (db)... 2 Table 2. Noise Receiver Linearity (db)... 2 Table 3. Noise Receiver Input Range... 22 Test Port Output: Option H29... 23 Table 4. Max Leveled Power, Port Filtered Mode (dbm)... 23 Table 5. Max Leveled Power, Port High Power Mode (dbm)... 24 Table 6. Max Leveled Power, Port Source, Combine Mode, Filtered Mode (dbm)... 25 Table 7. Max Leveled Power, Port Source, Combine Mode, High Power Mode (dbm)... 26 Table 8. Max Leveled Power, Port Source 2, Combine Mode, Filtered Mode (dbm)... 27 Table 9. Max Leveled Power, Port Source 2, Combine Mode, High Power Mode (dbm)... 28 Table 2. Max Leveled Power, Port 2 (dbm)... 29 Test Set Block Diagrams... 3 Figure. 4-Port N5244A and N5245A Option 423/H29... 3 Receiver Block Diagram... 3
This is the technical specifications for the N5244A and N5245A PNA-X network analyzer with option H29. Option H29, adds 26.5 GHz low-noise receivers to N5244A/45A for fully-corrected noise figure measurements of amplifiers, frequency converters, and mixers, utilizing source-correction technique (requires option 4, 49 and 423). See the block diagram. Option 4, 4-port standard test set (includes twelve front-panel access loops), power range, and an internal second source (Option 8 recommended). Option 49, adds 4-port extended power range, source and receiver attenuators, and bias-tees (requires Option 4). Option 423, adds an internal combiner, and mechanical switches to the 4-port analyzer (requires Option 4, 49, and 8). Notes In noise mode, the S-parameter measurement performance above 26.5 GHz is degraded due to the 26.5 GHz noise coupler in the port 2 source path (shown in green on the block diagram on page 3). Noise measurements are not specified above 26.5GHz. This document provides technical specifications for the 8556A calibration kit, and the N4693A 2- Port ECal module. Please download our free Uncertainty Calculator from http://www.agilent.com/find/na_calculator to generate the curves for your calibration kit and PNA setup. Definitions All specifications and characteristics apply over a 25 C ±5 C range (unless otherwise stated) and 9 minutes after the instrument has been turned on. Specification (spec.): Warranted performance. Specifications include guardbands to account for the expected statistical performance distribution, measurement uncertainties, and changes in performance due to environmental conditions. Characteristic (char.): A performance parameter that the product is expected to meet before it leaves the factory, but that is not verified in the field and is not covered by the product warranty. A characteristic includes the same guardbands as a specification. Typical (typ.): Expected performance of an average unit which does not include guardbands. It is not covered by the product warranty. Nominal (nom.): A general, descriptive term that does not imply a level of performance. It is not covered by the product warranty. Calibration: The process of measuring known standards to characterize a network analyzer's systematic (repeatable) errors. Corrected (residual): Indicates performance after error correction (calibration). It is determined by the quality of calibration standards and how well "known" they are, plus system repeatability, stability, and noise. Uncorrected (raw): Indicates instrument performance without error correction. The uncorrected performance affects the stability of a calibration. Standard: When referring to the analyzer, this includes no options unless noted otherwise.
Specifications: N5244A and N5245A Option H29 General specifications apply to Option H29 with the port noise tuner switch set to the internal position except as stated below. By default, the switch is set to the external position to ensure functional compatibility with existing PNA instruments. Refer to the Help System topic Noise Figure Application for information on setting the switch position. Corrected System Performance with 3.5mm Connectors Note: For any Sii reflection measurement: Sjj =. For any Sij transmission measurement: Sji = Sij when Sij Sji = /Sij when Sij Skk = for all k Table. 8556A Calibration Kit N5244A and N5245A Option H29 Applies to the N5244A and N5245A analyzer with Option H29, an 8556A (2.4mm) calibration kit, an 8533F flexible test port cable set, and a full 2-port calibration. S-parameter measurements were made with the analyzer in the noise figure configuration. Environmental temperature 23 ±3 C, with < C deviation from calibration temperature. Description Specification (db) MHz to 45 MHz 45 MHz to 2 GHz 2 GHz to 2 GHz 2 GHz to 26.5 GHz 26.5 GHz to 4 GHz 4 GHz to 5 GHz Directivity 42 42 42 38 38 36 Source Match 4 4 38 33 33 3 Load Match 42 42 4 37 37 35 Reflection Tracking Mag ±. ±. ±.8 ±.2 ±.2 ±.27 Phase +.9/ C +.9/ C +.54/ C +.33/ C +.33/ C +.8/ C S2 Transmission Tracking Mag ±.6 ±.37 ±.77 ±.44 ±.89 ±.248 Phase +.42/ C +.246/ C +.58/ C +.95/ C +.8/ C +.636/ C S2 Transmission Tracking Mag ±.5 ±.4 ±.7 ±.35 ±.83 ±.242 Phase +.338/ C +.268/ C +.468/ C +.89/ C +.28/ C +.598/ C Temperature deviation is a characteristic value. 5
Uncertainty (db) Uncertainty (degrees) Uncertainty (db) Uncertainty (degrees) Specifications: N5244A and N5245A Option H29 (continued) Transmission Uncertainty (S2) The following charts were generated for Opt 423 / H29. N5244A Opt 423 / H29 with 8556A (S2) Magnitude N5244A 423/H29(N,2N) Full Two Port Cal Using 8556A 26.5 GHz to 43.5 GHz Phase N5244A 423/H29(N,2N) Full Two Port Cal Using 8556A 26.5 GHz to 43.5 GHz.. - -2-3 -4-5 -6-7 S = S22 = Source Power = -5 dbm -8-9 -. - -2-3 -4-5 -6-7 S = S22 = Source Power = -5 dbm -8-9 - N5245 Opt 423 / H29 with 8556A (S2) Magnitude N5245A 423/H29(N,2N) Full Two Port Cal Using 8556A 26.5 GHz to 5 GHz Phase N5245A 423/H29(N,2N) Full Two Port Cal Using 8556A 26.5 GHz to 5 GHz.. - -2-3 -4-5 -6-7 S = S22 = Source Power = -5 dbm -8-9 -. - -2-3 -4-5 -6-7 S = S22 = Source Power = -5 dbm -8-9 - 6
Uncertainty (db) Uncertainty (degrees) Uncertainty (db) Uncertainty (degrees) Specifications: N5244A and N5245A Option H29 (continued) Transmission Uncertainty (S2) The following charts were generated for Opt 423 / H29. N5244A Opt 423 / H29 with 8556A (S2) Magnitude N5244A 423/H29(2N,N) Full Two Port Cal Using 8556A 26.5 GHz to 43.5 GHz Phase N5244A 423/H29(2N,N) Full Two Port Cal Using 8556A 26.5 GHz to 43.5 GHz.. - -2-3 -4-5 -6-7 S = S22 = Source Power = -5 dbm -8-9 -. - -2-3 -4-5 -6-7 S = S22 = Source Power = -5 dbm -8-9 - N5245 Opt 423 / H29 with 8556A (S2) Magnitude N5245A 423/H29(2N,N) Full Two Port Cal Using 8556A 26.5 GHz to 5 GHz Phase N5245A 423/H29(2N,N) Full Two Port Cal Using 8556A 26.5 GHz to 5 GHz.. - -2-3 -4-5 -6-7 S = S22 = Source Power = -5 dbm -8-9 -. - -2-3 -4-5 -6-7 S = S22 = Source Power = -5 dbm -8-9 - 7
Uncertainty (linear) Uncertainty (deg) Uncertainty (linear) Uncertainty (deg) Specifications: N5244A and N5245A Option H29 (continued) Reflection Uncertainty The following charts were generated for Opt 423 / H29. N5244A Opt 423 / H29 with 8556A Magnitude N5244A 423/H29(N,2N) with 8556A.5.4 26.5 GHz to 43.5 GHz.3.2 S2 = S2 = Source Power = -5 dbm Phase 8 6 4 N5244A 423/H29(N,2N) with 8556A 26.5 GHz to 43.5 GHz S2 = S2 = Source Power = -5 dbm. 2-2.78E-7.2.4.6.8 Reflection Coefficient (linear).2.4.6.8 Reflection Coefficient (linear) N5245A Opt 423 / H29 with 8556A Magnitude N5245A 423/H29(N,2N) with 8556A.5.4 26.5 GHz to 5 GHz.3.2 S2 = S2 = Source Power = -5 dbm Phase 8 6 4 N5245A 423/H29(N,2N) with 8556A 26.5 GHz to 5 GHz S2 = S2 = Source Power = -5 dbm. 2-2.78E-7.2.4.6.8 Reflection Coefficient (linear).2.4.6.8 Reflection Coefficient (linear) 8
Specifications: N5244A and N5245A Option H29 (continued) Table 2. N4693A 2- Port Electronic Calibration Module N5244A and N5245A Option H29 Applies to the N5244A and N5245A analyzer with Option H29, an N4693A (2.4 mm) electronic calibration module, an 8533F flexible test port cable set, and a full 2-port calibration. S-parameter measurements were made with the analyzer in the noise figure configuration. Environmental temperature 23 ±3 C, with < C deviation from calibration temperature. Description Specification (db) MHz to 45 MHz 45 MHz to 2 GHz 2 GHz to 2 GHz 2 GHz to 26.5 GHz 26.5 GHz to 4 GHz 4 GHz to 5 GHz Directivity 32 55 49 45 43 4 Source Match 25 46 42 37 35 3 Load Match 25 44 4 35 33 29 Reflection Tracking Mag ±.5.3.4.5 ±.6 ±.8 Phase +.33/ C +.98/ C +.264/ C +.33/ C +.396/ C +.528/ C S2 Transmission Tracking Mag ±.46 ±.35 ±.56 ±.76 ±.98 ±.28 Phase.966/ C.234/ C.37/ C.5/ C +.65/ C +.847/ C S2 Transmission Tracking Mag ±.8 ±.34 ±.5 ±.69 ±.94 ±.23 Phase +.78/ C +.224/ C +.328/ C +.457/ C +.622/ C +.82/ C Temperature deviation is a characteristic value. 9
Uncertainty (db) Uncertainty (degrees) Uncertainty (db) Uncertainty (degrees) Specifications: N5244A and N5245A Option H29 (continued) Transmission Uncertainty (S2) The following charts were generated for Opt 423 / H29. N5244A Opt 423 / H29 with N4693A (S2) Magnitude N5244A 423/H29(N,2N) Full Two Port Cal Using N4693A 26.5 GHz to 43.5 GHz Phase N5244A 423/H29(N,2N) Full Two Port Cal Using N4693A 26.5 GHz to 43.5 GHz.. - -2-3 -4-5 -6-7 S = S22 = Source Power = -5 dbm -8-9 -. - -2-3 -4-5 -6-7 S = S22 = Source Power = -5 dbm -8-9 - N5245A Opt 423 / H29 with N4693A (S2) Magnitude N5245A 423/H29(N,2N) Full Two Port Cal Using N4693A 26.5 GHz to 5 GHz Phase N5245A 423/H29(N,2N) Full Two Port Cal Using N4693A 26.5 GHz to 5 GHz.. - -2-3 -4-5 -6-7 S = S22 = Source Power = -5 dbm -8-9 -. - -2-3 -4-5 -6-7 S = S22 = Source Power = -5 dbm -8-9 -
Uncertainty (db) Uncertainty (degrees) Uncertainty (db) Uncertainty (degrees) Specifications: N5244A and N5245A Option H29 (continued) Transmission Uncertainty (S2) The following charts were generated for Opt 423 / H29. N5244A Opt 423 / H29 with N4693A (S2) Magnitude N5244A 423/H29(2N,N) Full Two Port Cal Using N4693A 26.5 GHz to 43.5 GHz Phase N5244A 423/H29(2N,N) Full Two Port Cal Using N4693A 26.5 GHz to 43.5 GHz.. - -2-3 -4-5 -6-7 S = S22 = Source Power = -5 dbm -8-9 -. - -2-3 -4-5 -6-7 S = S22 = Source Power = -5 dbm -8-9 - N5245A Opt 423 / H29 with N4693A (S2) Magnitude N5245A 423/H29(2N,N) Full Two Port Cal Using N4693A 26.5 GHz to 5 GHz Phase N5245A 423/H29(2N,N) Full Two Port Cal Using N4693A 26.5 GHz to 5 GHz.. - -2-3 -4-5 -6-7 S = S22 = Source Power = -5 dbm -8-9 -. - -2-3 -4-5 -6-7 S = S22 = Source Power = -5 dbm -8-9 -
Uncertainty (linear) Uncertainty (deg) Uncertainty (linear) Uncertainty (deg) Specifications: N5244A and N5245A Option H29 (continued) Reflection Uncertainty The following charts were generated for Opt 423 / H29. N5244A Opt 423 / H29 with N4693A Magnitude N5244A 423/H29(N,2N) with N4693A.5.4 26.5 GHz to 43.5 GHz.3.2 S2 = S2 = Source Power = -5 dbm Phase 8 6 4 N5244A 423/H29(N,2N) with N4693A 26.5 GHz to 43.5 GHz S2 = S2 = Source Power = -5 dbm. 2-2.78E-7.2.4.6.8 Reflection Coefficient (linear).2.4.6.8 Reflection Coefficient (linear) N5245A Opt 423 / H29 with N4693A Magnitude N5245A 423/H29(N,2N) with N4693A.5.4 26.5 GHz to 5 GHz.3.2 S2 = S2 = Source Power = -5 dbm Phase 8 6 4 N5245A 423/H29(N,2N) with N4693A 26.5 GHz to 5 GHz S2 = S2 = Source Power = -5 dbm. 2-2.78E-7.2.4.6.8 Reflection Coefficient (linear).2.4.6.8 Reflection Coefficient (linear) This document does not present specifications for the 8556D Calibration Kit. Please download our free Uncertainty Calculator from http://www.agilent.com/find/na_calculator to generate the data and curves for the 8556D Calibration Kit. 2
Uncorrected System Performance, N5244A and N5245A Option H29 Noise Error Terms: N5244A and N5245A Option H29 Table 3. Noise State Directivity, Port and Port 2 (db) Frequency Specification Typical MHz to 5 MHz 7 2 5MHz to 2MHz 22 27 2 MHz to 5 MHz 23 27 5 MHz to 3.2 GHz 23 3 3.2 GHz to GHz 22 25 GHz to 3.5 GHz 8 23 3.5 GHz to 6 GHz 8 2 6 GHz to 2 GHz 7 9 2 GHz to 24 GHz 5 9 24 GHz to 26.5 GHz 5 2 26.5GHz to 43.5GHz 5 2 43.5GHz to 46GHz 4 2 46GHz to 5GHz 4 8 Analyzer test set switches are set in accordance with the Figure block diagram on page 3, but with a jumper replacing the ECal module. 3
Table 4. Noise State Load Match, Port (db) Frequency Specification Typical MHz to 5 MHz 5 5 MHz to 5 MHz 6 22 5 MHz to 3.2 GHz 2 6 3.2 GHz to GHz 8 GHz to 3.5 GHz 7 3.5 GHz to 6 GHz 5 6 GHz to 2 GHz 7 2 GHz to 24 GHz 9 5 24 GHz to 26.5 GHz 8 4 26.5GHz to 43.5GHz 5 43.5GHz to 46GHz 5 46GHz to 5GHz 5 9 Analyzer test set switches are set in accordance with the Figure block diagram on page 3, but with a jumper replacing the ECal module. 4
Table 5. Noise State Load Match, Port 2 (db) Frequency Specification Typical MHz to 5 MHz 7 2 5 MHz to 5 MHz 2 8 5 MHz to 3.2 GHz 9 3.2 GHz to GHz 5.5 9.5 GHz to 3.5 GHz 5.5 9.5 3.5 GHz to 6 GHz 5.5 6 GHz to 2 GHz 5.5 2 GHz to 24 GHz 5.5.5 24 GHz to 26.5 GHz 5.5.5 26.5GHz to 43.5GHz 4 9 43.5GHz to 46GHz 4 9 46GHz to 5GHz 4 8 Analyzer test set switches are set in accordance with the Figure block diagram on page 3, but with a jumper replacing the ECal module. 5
Table 6. Noise State Reflection Tracking (S and S22), Min/Max (db) Frequency Specification Typical(S) Typical(S22) MHz to 5MHz -- +.5/-.5 +.5/-.5 5 MHz to 5MHz -- +.5/-.5 +.5/-.5 5 MHz to 3.2GHz -- +.5/-.5 +.5/-.5 3.2 GHz to GHz -- +.5/-.5 +.5/-.5 GHz to 3.5GHz -- +.5/-.5 +.5/-.5 3.5 GHz to 6GHz -- +.5/-.5 +.5/-.5 6 GHz to 2GHz -- +.5/-.5 +.5/-.5 2 GHz to 24 GHz -- +.5/-.5 +.5/-.5 24 GHz to 26.5GHz -- +.5/-2. +.5/-.5 26.5 GHz to 43.5GHz -- +.5/-2.5 +.5/-7 43.5 GHz to 46GHz -- +.5/-3. +.5/-9 46 GHz to 5GHz -- +.5/-3.5 +.5/-2 Table 7. Noise State Transmission Tracking, Min/Max (db) Frequency Specification Typical(Port) Typical(Port2) MHz to 5 MHz -- +.5/-.5 +.5/-.5 5 MHz to 5 MHz -- +.5/-.5 +.5/-.5 5 MHz to 3.2 GHz -- +.5/-.5 +.5/-.5 3.2 GHz to GHz -- +.5/-.5 +.5/-.5 GHz to 3.5 GHz -- +.5/-.5 +.5/-.5 3.5 GHz to 6 GHz -- +.5/-.5 +.5/-.5 6 GHz to 2 GHz -- +.5/-.5 +.5/-.5 2 GHz to 24 GHz -- +.5/-.5 +.5/-.5 24 GHz to 26.5 GHz -- +.5/-.5 +.5/-.5 26.5 GHz to 43.5GHz -- +.5/-5. +.5/-.5 43.5 GHz to 46GHz -- +.5/-5. +.5/-.5 46 GHz to 5GHz -- +.5/-25. +.5/-.5 6
Table 8. Noise State Source Match, Port (db) Frequency Specification Typical MHz to 5 MHz 8 2 5 MHz to 5 MHz 6 25 5 MHz to 3.2 GHz 6 2 3.2 GHz to GHz 2 8 GHz to 3.5 GHz 2 7 3.5 GHz to 6 GHz 2 7 6 GHz to 2 GHz 2 8 2 GHz to 24 GHz 9 5 24 GHz to 26.5 GHz 9 5 26.5 GHz to 43.5 GHz 5 43.5 GHz to 46 GHz 5 46 GHz to 5GHz 4 9 Analyzer test set switches are set in accordance with the Figure block diagram on page 3, but with a jumper replacing the ECal module. 7
Table 9. Noise State Source Match, Port 2 (db) Frequency Specification Typical MHz to 5 MHz 8 2 5 MHz to 5 MHz 7 5 MHz to 3.2 GHz 3 3.2 GHz to GHz 6 8 GHz to 3.5 GHz 6 9 3.5 GHz to 6 GHz 6 9 6 GHz to 2 GHz 6 2 GHz to 24 GHz 6 24 GHz to 26.5 GHz 6 26.5 GHz to 43.5 GHz 4 9 43.5 GHz to 46 GHz 4 46 GHz to 5GHz 3 8 Analyzer test set switches are set in accordance with the Figure block diagram on page 3, but with a jumper replacing the ECal module. 8
Test Port Input: Option H29 Table. Receiver Noise Figure, Port 2 (db) Frequency Specification Typical 8 khz High Gain Setting MHz to 6 MHz 2 22. -- 6 MHz to 2 MHz 9. -- 2 MHz to 2 GHz 2. -- 2 GHz to 3.5 GHz 4.5 -- 3.5 GHz to 2 GHz 4.5 -- 2 GHz to 26.5 GHz 7. -- 2 MHz, 4 MHz, 8 MHz BW, High Gain Setting MHz to 6 MHz 2 22. -- 6 MHz to 2 MHz 9. -- 2 MHz to 2 GHz 2. -- 2 GHz to 3.5 GHz 4.5 -- 3.5 GHz to 2 GHz 4.5 -- 2 GHz to 26.5 GHz 7. -- 24 MHz BW, High Gain Setting MHz to 6 MHz 2 36.5 -- 6 MHz to 2 MHz 9. -- 2 MHz to 2 GHz 2. -- 2 GHz to 3.5 GHz 4.5 -- 3.5 GHz to 6 GHz 4.5 -- 6 GHz to 26.5 GHz 8.5 -- Using Option H29 noise receivers. 2 Noise figure below 6 MHz is degraded due to noise from a local supply regulator in the N5244A/45A. 9
Table. Noise Jitter,2 (db) Frequency Specification Typical 4 MHz BW, Low Gain Setting MHz to 5 MHz.3.5 5 MHz to 3 GHz..7 3 GHz to 3.5 GHz..7 3.5 GHz to 26.5 GHz..7 4 MHz BW, Medium Gain Setting MHz to 5 MHz.3.5 5 MHz to 3 GHz..7 3 GHz to 3.5 GHz..7 3.5 GHz to 26.5 GHz..7 4 MHz BW, High Gain Setting MHz to 5 MHz..7 5 MHz to 3 GHz..7 3 GHz to 3.5 GHz..7 3.5 GHz to 26.5 GHz..7 2 points, noise average 2 May typically be degraded at frequencies below 5 MHz due to spurious noise receiver residuals. 2
Table 2. Noise Receiver Linearity (db) Power Range Specification Typical 4 MHz BW, Low Gain Setting -36 dbm to -64 dbm +/-.5 db -- -64 dbm to -7 dbm +/-. db -- 4 MHz BW, Medium Gain Setting -48 dbm to -76 dbm +/-.5 db -- -76 dbm to -86 dbm +/-. db -- 4 MHz BW, High Gain Setting -58 dbm to -84 dbm +/-.5 db -- -84 dbm to -92 dbm +/-. db -- 2
Table 3. Noise Receiver Input Range -- Specification Power Range High Gain Setting Medium Gain Setting Low Gain Setting 5 MHz to 3 GHz Max DUT NF + Gain (db) 32 db 44 db 55 db Max Input Power (dbm) for <. db Compression <=-57 dbm <=-45 dbm <=-36 dbm Max Operating Input Power (dbm) -37 dbm Typical -33 dbm Typical -26 dbm Typical Limit BW for full NF + Gain 4 MHz 4 MHz 4 MHz 3 GHz to 3.5 GHz Max DUT NF + Gain (db) 46 db 57 db 68 db Max Input Power (dbm) for <. db Compression Max Operating Input Power (dbm) Typical <=-43 dbm <=-32 dbm <=-2 dbm -23 dbm -2 dbm -3 dbm Limit BW for full NF + Gain 4 MHz 4 MHz 4 MHz 3.5 GHz to 26.5 GHz Max DUT NF + Gain (db) 46 db 57 db 68 db Max Input Power (dbm) for <. db Compression Max Operating Input Power (dbm) Typical <=-43 dbm <=-32 dbm <=-2 dbm -23 dbm -2 dbm -3 dbm Limit BW for full NF + Gain 4 MHz 4 MHz 4 MHz Derived from.25 db CW compression specification and -5 db offset, derived from exponential model for device compression. Referenced to test port 2. 22
Test Port Output: Option H29 Table 4. Max Leveled Power, Port Filtered Mode (dbm) Option 423/H29 Frequency Specification Typical MHz to 5 MHz 3 5 MHz to 5 MHz 7 5 MHz to 3.2 GHz 7 9 3.2 GHz to GHz 2 5 GHz to 3.5 GHz 2 3.5 GHz to 6 GHz 2 6 GHz to 2 GHz 9 2 2 GHz to 26.5 GHz 9 2 26.5 GHz to 3 GHz 8 2 3 GHz to 32GHz 6 32 GHz to 35 GHz 8 2 35 GHz to 4 GHz 2 6 4 GHz to 43.5 GHz 2 6 43.5 GHz to 47 GHz -4 2 47 GHz to 5 GHz -5-7 23
Table 5. Max Leveled Power, Port High Power Mode (dbm) Option 423/H29 Frequency Specification Typical MHz to 5 MHz 7 5 MHz to 2 GHz 2 5 2 GHz to 3.2 GHz 9 2 3.2 GHz to GHz 2 5 GHz to 3.5 GHz 2 3.5 GHz to 6 GHz 2 6 GHz to 2 GHz 9 2 2 GHz to 26.5 GHz 9 2 26.5 GHz to 3 GHz 8 2 3 GHz to 32 GHz 6 32 GHz to 35 GHz 8 2 35 GHz to 4 GHz 2 6 4 GHz to 43.5 GHz 2 6 43.5 GHz to 47 GHz -4 2 47 GHz to 5 GHz -5-7 24
Table 6. Max Leveled Power, Port Source, Combine Mode, Filtered Mode (dbm) Option 423/H29 Frequency Specification Typical MHz to 5 MHz -- 3 5 MHz to 5 MHz -- 3 5 MHz to 3.2 GHz -- 3 3.2 GHz to GHz -- 7 GHz to 3.5 GHz -- 3 3.5 GHz to 6 GHz -- 3 6 GHz to 2 GHz -- 2 GHz to 24 GHz -- 24 GHz to 26.5 GHz -- 26.5 GHz to 3 GHz -- 32 GHz to 35 GHz -- 35 GHz to 4 GHz -- -6 4 GHz to 43.5 GHz -- -6 43.5 GHz to 47 GHz -- - 47 GHz to 5 GHz -- -2 25
Table 7. Max Leveled Power, Port Source, Combine Mode, High Power Mode (dbm) Option 423/H29 Frequency Specification Typical MHz to 5 MHz -- 5 MHz to 5 MHz -- 5 MHz to 3.2 GHz -- 4 3.2 GHz to GHz -- 7 GHz to 3.5 GHz -- 3 3.5 GHz to 6 GHz -- 3 6 GHz to 2 GHz -- 2 GHz to 24 GHz -- 24 GHz to 26.5 GHz -- 26.5 GHz to 3 GHz -- 32 GHz to 35 GHz -- 35 GHz to 4 GHz -- -6 4 GHz to 43.5 GHz -- -6 43.5 GHz to 47 GHz -- - 47 GHz to 5 GHz -- -2 26
Table 8. Max Leveled Power, Port Source 2, Combine Mode, Filtered Mode (dbm) Option 423/H29 Frequency Specification Typical MHz to 5 MHz -- 4 5 MHz to 5 MHz -- 3 5 MHz to 3.2 GHz -- 3 3.2 GHz to GHz -- 6 GHz to 3.5 GHz -- 3 3.5 GHz to 6 GHz -- 3 6 GHz to 2 GHz -- 2 GHz to 24 GHz -- 24 GHz to 26.5 GHz -- 26.5 GHz to 3 GHz -- - 32 GHz to 35 GHz -- - 35 GHz to 4 GHz -- -7 4 GHz to 43.5 GHz -- -7 43.5 GHz to 47 GHz -- -2 47 GHz to 5 GHz -- -24 27
Table 9. Max Leveled Power, Port Source 2, Combine Mode, High Power Mode (dbm) Option 423/H29 Frequency Specification Typical MHz to 5 MHz -- 5 MHz to 5 MHz -- 5 MHz to 3.2 GHz -- 4 3.2 GHz to GHz -- 6 GHz to 3.5 GHz -- 3 3.5 GHz to 6 GHz -- 3 6 GHz to 2 GHz -- 2 GHz to 24 GHz -- 24 GHz to 26.5 GHz -- 26.5 GHz to 3 GHz -- - 32 GHz to 35 GHz -- - 35 GHz to 4 GHz -- -7 4 GHz to 43.5 GHz -- -7 43.5 GHz to 47 GHz -- -2 47 GHz to 5 GHz -- -24 28
Table 2. Max Leveled Power, Port 2 (dbm) Option 423/H29 Frequency Specification Typical MHz to 5 MHz 9 8 5 MHz to 5 MHz 2 8 5 MHz to 3.2 GHz 2 5 3.2 GHz to GHz 2 5 GHz to 3.5 GHz 2 3.5 GHz to 6 GHz 2 6 GHz to 2 GHz 8 2 GHz to 26.5 GHz 8 26.5 GHz to 3 GHz 7 3 GHz to 32 GHz 5 9 32 GHz to 35 GHz 7 35 GHz to 4 GHz 5 4 GHz to 43.5 GHz 5 43.5 GHz to 47 GHz -5 2 47 GHz to 5 GHz -5-6 29
Test Set Block Diagrams NOTE: For best readability, use a color printer for printing the following graphics. Figure. 4-Port N5244A and N5245A Option 423/H29 Adds internal combiner and mechanical switches. Also shown, Option 25 adds 4 pulse generators. Option 2 and 22 adds pulse modulators. Receiver Block Diagram 3
Agilent Email Updates www.agilent.com/find/emailupd ates Get the latest information on the products and applications you select.. www.axiestandard.org AdvancedTCA Extensions for Instrumentation and Test (AXIe) is an open standard that extends the AdvancedTCA for general purpose and semiconductor test. Agilent is a founding member of the AXIe consortium. www.lxistandard.org LAN extensions for Instruments puts the power of Ethernet and the Web inside your test systems. Agilent is a founding member of the LXI consortium. www.pxisa.org PCI extensions for Instrumentation (PXI) modular instrumentation delivers a rugged, PC-based highperformance measurement and automation system. Agilent Channel Partners www.agilent.com/find/channelpartn ers Get the best of both worlds: Agilent s measurement expertise and product breadth, combined with channel partner convenience. www.agilent.com www.agilent.com/find/pnax For more information on Agilent Technologies products, applications or services, please contact your local Agilent office. The complete list is available at: www.agilent.com/find/contactus Americas Canada Brazil Mexico United States Asia Pacific Australia China Hong Kong India Japan Korea Malaysia Singapore Taiwan Other AP Countries Europe & Middle East Belgium Denmark Finland France Germany Ireland Israel Italy Netherlands Spain Sweden United Kingdom For other unlisted countries: (877) 894-444 () 497 35 8 564 8 (8) 829-4444 8 629 485 8 8 89 8 938 693 8 2 929 2 (42) 345 8 769 8 8 888 848 8 375 8 8 47 866 (65) 375 8 32 () 2 44 93 4 45 7 3 5 5 358 () 855 2 825 7* *.25 /minute 49 () 73 464 6333 89 924 24 972-3-9288-54/544 39 2 92 6 8 484 3 () 2 547 2 34 (9) 63 33 2-88 22 55 44 () 8 92762 www.agilent.com/find/contactus Product specifications and descriptions in this document subject to change without notice. Agilent Technologies, Inc. Published in USA, Dec 6, 22 Supersedes: June 3, 2 N5245-96