TABLE OF CONTENTS General Information..................................... Elevation Notes......................................... Elevation Notes Transom................................. Light Cut Information.................................... Clear Opening Design Data Table 1 & 2 Panel................. Clear Opening Design Data Table 3 & 4 Panel................. Clear Opening Layout.................................... Unit Sizing, s, & Masonry Openings............. 9-2 9-3 9-4 9-5 9-6 9-7 9-8 9-9 Trim Options............................................ 9-10 Frame Options.......................................... Mullion Options......................................... Raised Panel Options..................................... 9-11 9-12 9-13 Bottom Rail Options...................................... 9-14 Stile Options............................................ Sill Options............................................. Divided Lite Options..................................... Section Details......................................... 9-15 9-16 9-17 9-19 Page 9-1
GENERAL INFORMATION DIMENSIONAL DOORS Siteline Clad Inswing Patio Doors may be specified as "dimensional", by adjusting the desired rough opening width or height in 1/8" increments from standard. Siteline Clad Inswing Patio Doors are available in single, twin, triple and quad panel doors. The standard size range includes sizes specifically designed for replacement of older patio door models in existing structures, as well as a full range of "true size" products for architectural consistency. Please consult our Quick Quote software for detailed product options and availability. OPERATION Siteline Clad Inswing Patio Doors are available in a full range of operating styles. Single panel doors may be specified as stationary (non-venting) or can operate left or right. Center swing two-or three-panel doors are available with left or right operation. Page 9-2
ELEVATION NOTES ELEVATION DRAWINGS UTILIZE A LIMITED NUMBER OF PROJECTED LINES TO PRODUCE A RUDIMENTARY DRAWING INTENDED TO BE USED IN A SMALL GRAPHICAL SCALE. ELEVATIONS ARE VIEWED PERPENDICULAR FROM THE EXTERIOR OF THE STRUCTURE. IF MORE DIMENSIONS ARE NEEDED, USE THE SECTION DRAWINGS FOR MORE COMPLETE DEPICTIONS. 36 (924) 35 5/8" (905) 24 3/16" (614) SEE SYMBOL LEGEND BELOW ## 80" (2032) 79 1/2" (2019) 63 5/8" (1680) OUTSIDE OF FRAME DAYLIGHT OPENING PRCISW3068 BOOK CODE 'PRCISW' INDICATES SITELINE CLAD INSWING WIDE STILE PATIO DOOR GENERAL SWINGING DOOR NOTES 1. PATIO DOOR (PRCISW) UNITS ARE AVAILABLE AS OPERATING OR FIXED UNITS. 2. UNIT ELEVATIONS ARE SHOWN WITHOUT EXTERIOR TRIM. UNIT SIZES & MASONRY OPENING DIMENSIONS WILL CHANGE WITH THE ADDITION OF EXTERIOR TRIM. SEE THE 'UNIT SIZING, ROUGH OPENINGS & MASONRY OPENINGS' PAGE FOR EXTERIOR TRIM EFFECTS. 3. OPERATING UNITS ARE AVAILABLE AS LEFT OR RIGHT HAND OPERATION. 4. HANDICAP SILL, 10" BOTTOM RAILS, INTERMEDIATE LOCK RAILS AND RAISED PANELS ARE AVAILABLE FOR ALL UNITS. ## THE LAST TWO NUMBERS INDICATE THE FRAME CALLOUT HEIGHT (FT. IN.) THE FIRST TWO OR THREE NUMBERS INDICATE THE FRAME CALLOUT WIDTH IN (FT. IN.) ELEVATION SYMBOL LEGEND NUMBER INDICATES PERFORMANCE GRADE (PG) RATING WITH STANDARD GLAZING FOR ALL UNITS EXCLUDING ADA SILL UNITS. NUMBER INDICATES PERFORMANCE GRADE (PG) WITH LIMITED WATER RATING WITH STANDARD GLAZING FOR ADA SILL UNITS. Page 9-3
ELEVATION NOTES ELEVATION DRAWINGS UTILIZE A LIMITED NUMBER OF PROJECTED LINES TO PRODUCE A RUDIMENTARY DRAWING INTENDED TO BE USED IN A SMALL GRAPHICAL SCALE. ELEVATIONS ARE VIEWED PERPENDICULAR FROM THE EXTERIOR OF THE STRUCTURE. IF MORE DIMENSIONS ARE NEEDED, USE THE SECTION DRAWINGS FOR MORE COMPLETE DEPICTIONS. ROUGH OPENING FRAME SIZE DAYLIGHT OPENING 24 3/4"(629) 24"(610) 17 5/16"(440) 72"(1829) 7(1810) 59 13/16"(1519) ## SEE SYMBOL LEGEND BELOW DAYLIGHT OPENING OUTSIDE OF FRAME PRCIST6020 BOOK CODE 'PRCIST' INDICATES SITELINE CLAD INSWING PATIO DOOR TRANSOM GENERAL SWINGING DOOR NOTES 1. PATIO DOOR TRANSOMS (PRCIST) UNITS ARE AVAILABLE AS FIXED UNITS ONLY. 2. UNIT ELEVATIONS ARE SHOWN WITHOUT EXTERIOR TRIM. UNIT SIZES & MASONRY OPENING DIMENSIONS WILL CHANGE WITH THE ADDITION OF EXTERIOR TRIM. SEE THE 'UNIT SIZING, ROUGH OPENINGS & MASONRY OPENINGS' PAGE FOR EXTERIOR TRIM EFFECTS. ## THE LAST TWO NUMBERS INDICATE THE FRAME CALLOUT HEIGHT (FT. IN.) THE FIRST TWO OR THREE NUMBERS INDICATE THE FRAME CALLOUT WIDTH IN (FT. IN.) ELEVATION SYMBOL LEGEND NUMBER INDICATES PERFORMANCE GRADE (PG) RATING WITH STANDARD GLAZING FOR ALL UNITS. Page 9-4
LIGHT CUT INFORMATION Siteline Clad Inswing Patio Doors are available with full surround removable grilles in, 1 1/8" and 1 widths, with grilles between the glass (GBG), or with simulated divided lites (SDL). Standard lite cuts are rectangular, and conform to the layouts noted in the charts on the next page. To use the chart, refer to the appropriate table by the type of patio door and type of bars or grilles the section drawings illustrate. Then simply cross reference the frame height and width to determine the standard lite cut. LITE CUT OPTIONS Special lite cut patterns can include a wide variety of straight line and radius patterns. The illustrations shown here represent just a few of the possibilities. Rectangular, horizontal, vertical and prairie lite patterns are available in all standard size clad swinging patio doors. Uneven, diamond, radius and gothic lite cuts are available, subject to approval. Approvals are based on the ability to fulfill the design requirement while maintaining the construction integrity of the finished product. RECTANGULAR HORIZONTAL VERTICAL PRAIRIE UNEVEN DIAMOND RADIUS GOTHIC EXTERIOR F/S GRILLE BAR 1 1/8" F/S GRILLE BAR 1 F/S GRILLE BAR 5/8" FLAT 23/32" CONTOUR 1" CONTOUR 5/8" PUTTY SDL BAR GBG EXTERIOR PUTTY 5/8" PUTTY SDL BAR PUTTY BEAD PUTTY BEAD 1 SDL BAR 2 5/16" SDL BAR 5/8" SDL BAR SDL BAR 1 1/8" SDL BAR Height Callout Width Callout 1-2 1-4 1-6 2-0 2-6 2-8 3-0 3-2 3-6 3-8 6-8 1W 5H 1W 5H 1W 5H 2W 5H 2W 5H 3W 5H 3W 5H 3W 5H 4W 5H 4W 5H 6-11 1W 5H 1W 5H 1W 5H 2W 5H 2W 5H 3W 5H 3W 5H 3W 5H 4W 5H 4W 5H 7-0T 1W 5H 1W 5H 1W 5H 2W 5H 2W 5H 3W 5H 3W 5H 3W 5H 4W 5H 4W 5H 8-0 1W 6H 1W 6H 1W 6H 2W 6H 2W 6H 3W 6H 3W 6H 3W 6H 4W 6H 4W 6H 8-0T 1W 6H 1W 6H 1W 6H 2W 6H 2W 6H 3W 6H 3W 6H 3W 6H 4W 6H 4W 6H 9-0 1W 7H 1W 7H 1W 7H 2W 7H 2W 7H 3W 7H 3W 7H 3W 7H 4W 7H 4W 7H 10-0 1W 7H 1W 7H 1W 7H 2W 7H 2W 7H 3W 7H 3W 7H 3W 7H 4W 7H 4W 7H Page 9-5
CLEAR OPENING DESIGN DATA TABLES 1 & 2 PANEL Page 9-6
CLEAR OPENING DESIGN DATA TABLES 3 & 4 PANEL Page 9-7
CLEAR OPENING LAYOUT 1 9/32" [33] HORIZONTAL Clear Opening Width Formulas (1-Panel ): Clear Opening @ 90 = Frame Width - 4 19/32" Clear Opening Maximum = Frame Width - 2 9/16" Maximum Wall = 2 x Frame Width - 2 15/16" VERTICAL CLEAR OPENING HEIGHT 1 9/32" [33] 3 5/16" [84] CLEAR OPENING @ 90 CLEAR OPENING @ MAXIMUM MAXIMUM WALL = 2 x FRAME WIDTH - 2 15/16"[75] VERTICAL 10 3/16" [258] 1 [35] Clear Opening Height Formulas: With DP35 Sill Clear Opening Height = Frame Height - 2 21/32" 1 9/32" [33] 2 1/32" [52] CLEAR OPENING @ 90 CLEAR OPENING @ MAXIMUM FRAME WIDTH / 2 HORIZONTAL 2 Panel unit hinged from fixed mullion. Clear Opening Width Formulas: Clear Opening @ 90 = (Frame Width / 2) - 4 19/32" Clear Opening @ Maximum = (Frame Width / 2) - 2 9/16" 1 9/32" [33] HORIZONTAL French Doors hinged off jamb Clear Opening Width Formulas: Clear Opening @ 90 = Frame Width - 6-5/8" Clear Opening Maximum = Frame Width - 2 9/16" Maximum Wall = 2 x Frame Width - 3 1 9/32" [33] CLEAR OPENING @ 90 3 5/16" [84] CLEAR OPENING @ MAXIMUM Panel Callout 1-2 1-4 1-6 2-0 2-6 2-8 3-0 3-2 3-6 3-8 Panel Width 12-15/16 14-15/16 16-15/16 21-15/16 27-15/16 29-15/16 33-15/16 35-15/16 39-15/16 41-15/16 HORIZONTAL 4 panel unit - French door flanked by two stationary panels. Clear Opening Width Formulas: Clear Opening @ 90 = (Frame Width / 2) - 6 5/8" Clear Opening Maximum = (Frame Width / 2) - 2 9/16" 1 9/32" [33] CLEAR OPENING @ 90 CLEAR OPENING @ MAXIMUM FRAME WIDTH / 2 2 1/32" [52] Page 9-8
UNIT SIZING ROUGH OPENINGS AND MASONRY OPENINGS STANDARD OFFERING DRIP CAP & NAILING FLANGE HORIZONTAL GENERAL NOTES: ROUGH OPENING HEIGHT IS ALWAYS FRAME SIZE + 1/2" ROUGH OPENING WIDTH IS ALWAYS FRAME SIZE + 3/4" MASONRY OPENING: MASONRY OPENING IS ALWAYS 1/2" OVER THE UNIT SIZE OF THE DOOR ROUGH OPENING: DRIP CAP & NAILING FLANGE VERTICAL [10] HORIZONTAL ROUGH OPENING [10] 3" [76] 1 1/2" [38] 1/2" [13] UNIT SIZE FRAME TO EXTERIOR TRIM (UNIT) SIZE 1 1/2" [38] 1 1/2" [38] 3" [76] 3" [76] HORIZONTAL CASING SIZE FOR BRICKMOULD & BEADED BRICKMOULD IS FRAME WIDTH + 3" [76] BRICKMOULD BEADED BRICKMOULD 3 1/2" FLAT CASING ADAMS CASING 1 1/2" [38] 1 1/2" [38] 3" [76] 3" [76] VERTICAL UNIT SIZE 3 1/2" FLAT CASING & ADAMS CASING FRAME + 3" [76] VERTICAL UNIT SIZE BRICKMOULD & BEADED BRICKMOULD FRAME + 1 1/2" [38] VERTICAL ROUGH OPENING HORIZONTAL CASING SIZE FOR 3 1/2" FLAT CASING & ADAMS CASING IS FRAME WIDTH + 6" [152] Page 9-9
TRIM OPTIONS STANDARD NAIL FIN BRICKMOULD BEADED BRICKMOULD ADAMS CASING 3 1/2" FLAT CASING SCALE: 3" = 1' - 0" Page 9-10
FRAME OPTIONS 7 13/16" 6 9/16" FRAME OPTION 6 9/16" FRAME OPTION 8 5/16" 7 1/16" 1/2" 7 1/16" FRAME OPTION SCALE: 3" = 1' - 0" Page 9-11
MULLION OPTIONS 2" VERTICAL MULL SECTION TRANSOM OVER WIDE STILE UNIT 1/4" 1/4" 2" 9 1/16" 9 5/16" VERTICAL MULL SECTION TRANSOM OVER WIDE STILE UNIT WITH 1/4" REINFORCEMENT SCALE: 3" = 1' - 0" Page 9-12
RAISED PANEL OPTIONS STANDARD GLAZED PANEL OPTION 1 OPTION 2 INTERIOR FLAT PANEL - INTERIOR RAISED PANEL - EXTERIOR FLAT PANEL EXTERIOR FLAT PANEL SCALE: 1/2" = 1' - 0" Page 9-13
BOTTOM RAIL OPTIONS 1/4" 8 1/2" 8 1/4" 1/4" 7 10 1/4" 10" 9 5/8" 1 3/4" 1 3/4" 8 1/4" BOTTOM RAIL 10" BOTTOM RAIL SCALE: 6" = 1' - 0" Page 9-14
STILE OPTIONS 1 1 3/4" 2 1/2" SIDELITE STILE 3" 1 3/4" NARROW STILE 4 1/4" 1 3/4" 4 WIDE STILE SCALE: 6" = 1' - 0" Page 9-15
SILL OPTIONS 5 15/16" 1 5 15/16" DP35 SILL OPTION 7 15/16" 1 DP50 SILL OPTION 7 15/16" 2" 2" 6 9/16" DP35 SILL OPTION 6 9/16" DP50 SILL OPTION 9 15/16" 9" DP35 SILL OPTION 9 15/16" 2" 1 9" DP50 SILL OPTION 8 1/8" 1/2" ADA SILL OPTION SCALE: 3" = 1' - 0" Page 9-16
DIVIDED LITE OPTIONS BEAD SDL W/ LIGHT BRONZE SHADOW BAR BEAD SDL W/ SILVER SHADOW BAR 1 1/8" BEAD SDL W/ LIGHT BRONZE SHADOW BAR 1 1/8" BEAD SDL W/ SILVER SHADOW BAR 1 BEAD SDL W/ LIGHT BRONZE SHADOW BAR 1 BEAD SDL W/ SILVER SHADOW BAR 2-5/16" BEAD SDL W/ LIGHT BRONZE SHADOW BAR 2-5/16" BEAD SDL W/ SILVER SHADOW BAR NTS Page 9-17
DIVIDED LITE OPTIONS 5/8" PUTTY SDL PUTTY SDL 1 1/8" PUTTY SDL TRADITIONAL PUTTY TRADITIONAL PUTTY TRADITIONAL PUTTY 5/8" PUTTY SDL PUTTY SDL 1 1/8" PUTTY SDL PUTTY/PUTTY PUTTY/PUTTY PUTTY/PUTTY 5/8" GBG 23/32" CONTOUR W/ 1" CONTOUR GBG GBG FULL SURROUND WOOD GRILLE FULL SURROUND 1 1/8" WOOD GRILLE FULL SURROUND 1 WOOD GRILLE NTS Page 9-18
VERTICAL SECTION DP35 SILL 1/2" 4 8 1/2" 1 1 5 15/16" Page 9-17
ADA VERTICAL SECTION 1/2" 4 10 1/4" 13/16" 1/2" 8 1/8" Page 9-18
VERTICAL SECTION STATIONARY DP35 SILL 1/2" 4 8 1/2" 1 5 15/16" Page 9-19
HORIZONTAL SECTION 1 PANEL 4 4 Page 9-20
HORIZONTAL SECTION 1 PANEL WIDE STILE STATIONARY 4 4 Page 9-21
HORIZONTAL SECTION 1 PANEL NARROW STILE 3 5/8" 3 5/8" Page 9-22
HORIZONTAL SECTION 1 PANEL SIDELITE STILE STATIONARY 2 1/2" 2 1/2" Page 9-23
HORIZONTAL SECTION VENTING SIDELITE 2 1/2" 2 1/2" Page 9-24
HORIZONTAL SECTION FIXED WIDE STILE W/ CENTER HINGED 4 4 4 4 1 Page 9-25
HORIZONTAL SECTION FIXED NARROW STILE W/ CENTER HINGED 3 5/8" 3 5/8" 1 4 4 Page 9-26
HORIZONTAL SECTION FIXED SIDELITE STILE W/ CENTER HINGED 2 1/2" 2 1/2" 1 4 4 Page 9-27
HORIZONTAL SECTION FIXED WIDE STILE W/ SIDE HINGED 4 4 1 4 4 Page 9-28
HORIZONTAL SECTION FIXED NARROWS STILE W/ SIDE HINGED 4 4 3 5/8" 3 5/8" 1 Page 9-29
HORIZONTAL SECTION FIXED SIDELITE STILE W/ SIDE HINGED 4 4 2 1/2" 2 1/2" 1 Page 9-30
FRENCH HORIZONTAL SECTION 4 4 4 4 1 7/16" Page 9-31
QUAD HORIZONTAL SECTION 2 1/2" 2 1/2" 4 1 1 7/16" 4 Page 9-32
VERTICAL SECTION RADIUS TOP 1/2" 4 6" 1 7/16" 1 5/8" 5 15/16" Page 9-33
HORIZONTAL SECTION 13/16" 13/16" 4 4 4 4 1 Page 9-34
HORIZONTAL SECTION IN-SWING WIDE STILE TRANSOM 4 Sash Size 4 Page 9-35
HORIZONTAL SECTION IN-SWING NARROW STILE TRANSOM 3 5/8" Sash Size 3 5/8" Page 9-36
HORIZONTAL SECTION IN-SWING SIDELITE STILE TRANSOM Sash Size 2 1/2" 2 1/2" Page 9-37
HORIZONATAL SECTION IN-SWING WIDE STILE TRANSOM - 2 PANEL Sash Size Sash Size 4 4 4 4 1 Page 9-38
HORIZONATAL SECTION IN-SWING NARROW STILE TRANSOM - 2 PANEL 3 5/8" Sash Size 3 5/8" 3 5/8" Sash Size 3 5/8" 1 Page 9-39
HORIZONATAL SECTION IN-SWING SIDELITE STILE TRANSOM - 2 PANEL 2 1/2" Sash Size 2 1/2" 2 1/2" Sash Size 2 1/2" 1 Page 9-40
HORIZONATAL SECTION IN-SWING WIDE STILE TRANSOM - 3 PANEL Sash Size 4 4 4 Sash Size 1 Page 9-41
HORIZONATAL SECTION IN-SWING NARROW STILE TRANSOM - 3 PANEL Sash Size 3 5/8" 3 5/8" 3 5/8" Sash Size 1 Page 9-42
HORIZONATAL SECTION IN-SWING SIDELITE STILE TRANSOM - 3 PANEL Sash Size 2 1/2" 2 1/2" 2 1/2" Sash Size 1 Page 9-43