SD-6200 IrDA SD-6100 IrDA UHF 2-way Sync True Diversity / Diversity Wireless Microphone Operation manual ISO 9001 EGISTEED INTENATIONAL ISO 14001 ISO 14001 EGISTEED INTENATIONAL OHSAS 18001 OHSAS 18001 GEEN PODUCT
Thank you for choosing this wireless microphone system! Our products are designed to last and for user friendly operation. Each system consists of 1. a receiver 2. a handheld or belt-pack transmitter 3. a pair of antennas 4. a switching adaptor 5. an operation manual For more details, please take a few moments to read this operating manual to have a thorough understanding of the function and operation of both transmitter and receiver. Parts and functions of SD-6200 IrDA/SD-6100 IrDA receiver Front panel 1 2 POWE 1. Power switch 2. I sensor area 3. Diversity indicator 4. Audio signal indicator 5. LCD display 6. UP button 7. DOWN button 8. IrDA synchronization button 9. SET button ear panel A B 3 4 D IV E S IT Y A U D IO 5 SD-6100 IrDA UHF 2-WAY SYNC. DIVESITY ECEIVE 6 7 8 9 10 11 12 14 13 SD-6200 IrDA ANT.B 10 BALANCED 1.GND 2. 3. MIC OUT 11 UNBALANCED 12 LINE OUT ANT.A DC IN 12V 13 14 SD-6100 IrDA 10. Antenna B socket (TNC) 11. Balanced audio output 12. Unbalanced audio output 13. Antenna A socket (TNC) 14. DC in -1-
ISO 9001 ISO 14001 OHSAS 18001 Changing CHANNEL / FEQUENCY 1. Press and release SET button until the CHANNEL-FEQUENCY page appears. 2. Press (UP) or (DOWN) button to select a new channel. As the channel changes, the frequency changes accordingly, too. 3. After a channel is chosen, wait 5 seconds to store the setting. CHANNEL SYNCHONIZING of the receiver and transmitter Align infrared areas of the receiver and transmitter within 30cm. < 30cm A. Changing the receiver s channel B. Changing the transmitter s channel 1. Press the synchronizing button of the transmitter. 1. Press the SYNC button of the receiver. A B POWE D IV E S IT Y A U D IO SD-6200 IrDA UHF 2-WAY SYNC. TUE DIVESITY ECEIVE 2. The transmitter's LED will grow to denote synchronizing signal transmitted. 2. IDA DATA SEND will appear on the receiver s display 3. COPIED BY IDA will appear on the receiver's LCD, which means the receiver has been successfully synchronized. 3. Then IDA TX FINISH will appear to denote data transferred. -2-
CHANNEL scanning For an interference- free operation, a cleaner channel might be necessary if the current one receives too much interference. Before scanning, the transmitter must be switched off. 1. Press and release SET button until the AUTO SCAN page appears. 2. Press (UP) or (DOWN) button to find and locate a clear, interference- free channel. 3. After a channel is chosen, wait 5 seconds to store the setting. Adjusting VOLUME level 1. The setting can be made right on the homepage. 2. Press (UP) or (DOWN) button to choose a new level. POWE A B D IV E S IT Y A U D IO SD-6200 IrDA UHF 2-WAY SYNC. TUE DIVESITY ECEIVE 3. After the setting is made, wait 5 seconds to store the setting. Adjusting SQUELCH level When interference is encountered try reducing the sensitivity of the receiver, thus less susceptible to interference. 1. Press and release SET button until the SQUELCH SETUP page appears. 2. Then press (UP) or (DOWN) button to choose a new level between 1 and 10. IrDA UHF 2-WAY SYNC. TUE DIVESITY ECEIVE D IV E S IT Y POWE A B A U D IO SD-6200 IrDA UHF 2-WAY SYNC. TUE DIVESITY ECEIVE 3. After a level is chosen, wait 5 seconds to store the setting. Since increasing the squelch level will also reduce the reception distance, it s recommended to choose the lowest level that can eliminate the interference. If this still does not solve the problem it means this frequency is not suitable. Adjust the squelch back to its preset level and use the scan function to locate a clear, interference-free channel. -3-
ISO 9001 ISO 14001 OHSAS 18001 eceiver installation 1. For best operation, the receiver should be at least 1m above the ground and 1m away from a wall or metal surface to minimize reflections. 2. The transmitter should also be at least 1m away from a wall or metal surface to minimize reflections. The transmitter should also be at least 1m away from the receiver. 3. Keep antennas away from noise source such as motors, automobiles, neon light as well as large metal objects. Audio output connection There are two audio outputs on the back of the receiver, Mic-level balanced and Line-level unbalanced. Use shielded audio cable for the connection between the receiver and the amplifier/mixer. If the amplifier/mixer has a 1/4"(6.3mm) phone jack, connect a cable from the 1/4"(6.3mm) unbalanced audio output from the receiver to the amplifier/mixer. If the amplifier/mixer has an XL input, connect a cable from the balanced XL audio output from the receiver to the amplifier/mixer input. 6.3mm phone jack connection XL connection -4-
ack mounting The receiver can be cabinet-mounted by either one or two units. If only one receiver is to be mounted, an optional kit is available and it's installed as shown in Fig 1. If two receivers are to be mounted, they can be assembled by another kit and installed as shown in Fig 2. Fig 1. ack mount one receiver Fig 2. ack mount two receivers -5-
CHIAYO ELECTONICS CO.,LTD. Http//www.chiayo.com.tw Email sales@chiayo.com.tw Office 30, Lane 27, Section 4, Jen-Ai oad, Taipei 10685, Taiwan Tel 886-2-27415741 Fax 886-2-27525242 Factory 88, Chung-Hsiao Street 2, Chiayi 60080, Taiwan Tel 886-5-2711000 Fax 886-5-5767611 12I1373