Transient Stability Improvement Of IEEE 9 Bus System With Shunt FACTS Device STATCOM

Similar documents
Voltage Control and Power System Stability Enhancement using UPFC

Transient stability improvement by using shunt FACT device (STATCOM) with Reference Voltage Compensation (RVC) control scheme

Arvind Pahade and Nitin Saxena Department of Electrical Engineering, Jabalpur Engineering College, Jabalpur, (MP), India

Damping Power system Oscillation using Static Synchronous Series Compensator (SSSC)

Increasing Dynamic Stability of the Network Using Unified Power Flow Controller (UPFC)

Improving the Transient and Dynamic stability of the Network by Unified Power Flow Controller (UPFC)

ELEMENTS OF FACTS CONTROLLERS

Static Synchronous Compensator (STATCOM) for the improvement of the Electrical System performance with Non Linear load 1

IJSER. Fig-1: Interconnection diagram in the vicinity of the RajWest power plant

Transient Stability Improvement of Multi Machine Power Systems using Matrix Converter Based UPFC with ANN

Improvement of Power system transient stability using static synchronous series compensator

International Journal of Advance Engineering and Research Development

Enhancement of Voltage Stability & reactive Power Control of Distribution System Using Facts Devices

INTERNATIONAL JOURNAL OF ELECTRICAL ENGINEERING & TECHNOLOGY (IJEET)

Keywords: Stability, Power transfer, Flexible a.c. transmission system (FACTS), Unified power flow controller (UPFC). IJSER

Analysis of Effect on Transient Stability of Interconnected Power System by Introduction of HVDC Link.

STATCOM WITH POD CONTROLLER FOR REACTIVE POWER COMPENSATION Vijai Jairaj 1, Vishnu.J 2 and Sreenath.N.R 3

LOW FREQUENCY OSCILLATION DAMPING BY DISTRIBUTED POWER FLOW CONTROLLER WITH A ROBUST FUZZY SUPPLEMENTARY CONTROLLER

PERFORMANCE COMPARISON OF POWER SYSTEM STABILIZER WITH AND WITHOUT FACTS DEVICE

Chapter 10: Compensation of Power Transmission Systems

Stability Enhancement for Transmission Lines using Static Synchronous Series Compensator

SIMULATION OF D-Q CONTROL SYSTEM FOR A UNIFIED POWER FLOW CONTROLLER

Transient Stability Analysis of Multimachine System Using Statcom

Power System Stability Improvement in Multi-machine 14 Bus System Using STATCOM

Volume I Issue VI 2012 September-2012 ISSN

PUBLICATIONS OF PROBLEMS & APPLICATION IN ENGINEERING RESEARCH - PAPER CSEA2012 ISSN: ; e-issn:

Damping of Power System Oscillations and Control of Voltage Dip by Using STATCOM and UPFC

Application of SSSC-Damping Controller for Power System Stability Enhancement

Application Of Power System Stabilizer At Serir Power Plant

International Journal of Engineering & Computer Science IJECS-IJENS Vol:12 No:06 14 Smart Power Transmission System Using FACTS Device

Power System Oscillations Damping and Transient Stability Enhancement with Application of SSSC FACTS Devices

Comparison of FACTS Devices for Power System Stability Enhancement

A.V.Sudhakara Reddy 1, M. Ramasekhara Reddy 2, Dr. M. Vijaya Kumar 3

[Mahagaonkar*, 4.(8): August, 2015] ISSN: (I2OR), Publication Impact Factor: 3.785

ECE 422/522 Power System Operations & Planning/Power Systems Analysis II 5 - Reactive Power and Voltage Control

Transfer Capability Enhancement of Transmission Line using Static Synchronous Compensator (STATCOM)

Comparison of Adaptive Neuro-Fuzzy based PSS and SSSC Controllers for Enhancing Power System Oscillation Damping

EXPERIMENTAL INVESTIGATION OF THE ROLE OF STABILIZERS IN THE ENHANCEMENT OF AUTOMATIC VOLTAGE REGULATORS PERFORMANCE

Power Quality enhancement of a distribution line with DSTATCOM

Development of Dynamic Test Cases in OPAL-RT Real-time Power System Simulator

A Real-Time Platform for Teaching Power System Control Design

Improvement of Power Quality in PMSG Based Wind Integrated System Using FACTS Controller

Fuzzy Control Scheme for Damping of Oscillations in Multi Machine. Power System with UPFC

factors that can be affecting the performance of a electrical power transmission system. Main problems which cause instability to a power system is vo

I. INTRODUCTION. Keywords:- FACTS, TCSC, TCPAR,UPFC,ORPD

ENHANCEMENT OF POWER FLOW USING SSSC CONTROLLER

Comparison and Performance Analysis of FACTs Controller in System Stability

IJSER. Rajasthan power system power map is placed in Fig-1. Fig-1: Rajasthan Power System

COMPARATIVE PERFORMANCE OF SMART WIRES SMARTVALVE WITH EHV SERIES CAPACITOR: IMPLICATIONS FOR SUB-SYNCHRONOUS RESONANCE (SSR)

Dynamic stability of power systems

CHAPTER-IV EXPERIMENTAL AND SIMULATION PROGRAM

Performance Improvement of Power System Using Static Synchronous Compensator (STATCOM) Priya Naikwad, Mayuri Kalmegh, Poonam Bhonge

The Influence of Thyristor Controlled Phase Shifting Transformer on Balance Fault Analysis

Level 6 Graduate Diploma in Engineering Electrical Energy Systems

APPLICATION OF INVERTER BASED SHUNT DEVICE FOR VOLTAGE SAG MITIGATION DUE TO STARTING OF AN INDUCTION MOTOR LOAD

Power flow improvement using Static Synchronous Series Compensator (SSSC)

Investigation of D-Statcom Operation in Electric Distribution System

Bhavin Gondaliya 1st Head, Electrical Engineering Department Dr. Subhash Technical Campus, Junagadh, Gujarat (India)

Brief Study on TSCS, SSSC, SVC Facts Device

Mitigation of Voltage Sag and Swell using Distribution Static Synchronous Compensator (DSTATCOM)

Chapter-5 MODELING OF UNIFIED POWER FLOW CONTROLLER. There are a number of FACTS devices that control power system

Transmission Congestion and voltage profile management in long transmission Lines using UPFC with Fuzzy Logic Controller

LARGE-SCALE WIND POWER INTEGRATION, VOLTAGE STABILITY LIMITS AND MODAL ANALYSIS

Available ONLINE

Application of Unified Power Flow Controller in Interconnected Power Systems Modeling, Interface, Control Strategy, and Case Study

Application of Fuzzy Logic Controller in UPFC to Mitigate THD in Power System

Modelling of Fuzzy Generic Power System Stabilizer for SMIB System

Improvement of Rotor Angle Stability and Dynamic Performance of AC/DC Interconnected Transmission System

Power System Stability Enhancement Using Static Synchronous Series Compensator (SSSC)

In Class Examples (ICE)

Impact of Thyristor Controlled Series Capacitor on Voltage Profile of Transmission Lines using PSAT

D-STATCOM FOR VOLTAGE SAG, VOLTAGE SWELL MITIGATION USING MATLAB SIMULINK

STATCOM Control of Ill-Conditioned Power Systems Using Dogleg Trust-Region Algorithm

[Kumar*, 4.(7): July, 2015] ISSN: (I2OR), Publication Impact Factor: 3.785

TRANSIENT STABILITY ENHANCEMENT OF POWER SYSTEM USING INTELLIGENT TECHNIQUE

Development and Simulation of Voltage Regulation System of A.C. Transmission lines using Static Synchronous Compensator (STATCOM)

Optimal Placement of Shunt Connected Facts Device in a Series Compensated Long Transmission Line

Improvement of Power Quality Considering Voltage Stability in Grid Connected System by FACTS Devices

EXCITATION SYSTEM MODELS OF GENERATORS OF BALTI AND EESTI POWER PLANTS

ANALYTICAL AND SIMULATION RESULTS

Modelling and Analysis of Single Machine Infinite Bus System with and without UPFC for Different Locations of Unsymmetrical Fault

Enhancement of Power System Voltage Stability Using SVC and TCSC

Transient Stability Enhancement with Application of FACTS Devices

Power Quality Analysis in Power System with Non Linear Load

1 Introduction General Background The New Computer Environment Transmission System Developments Theoretical Models and Computer Programs

Course ELEC Introduction to electric power and energy systems. Additional exercises with answers December reactive power compensation

SIMULATION OF D-STATCOM AND DVR IN POWER SYSTEMS

Power System Stability. Course Notes PART-1

Analysis and Enhancement of Voltage Stability using Shunt Controlled FACTs Controller

Damping of Sub-synchronous Resonance and Power Swing using TCSC and Series capacitor

Energy-Based Damping Evaluation for Exciter Control in Power Systems

Analysis the Modeling and Control of Integrated STATCOM System to Improve Power System

I. INTRODUCTION IJSRST Volume 3 Issue 2 Print ISSN: Online ISSN: X

Robust controller design for LFO damping

Power Quality Improvement in Distribution System Using D-STATCOM

DESIGN OF A MODE DECOUPLING FOR VOLTAGE CONTROL OF WIND-DRIVEN IG SYSTEM

The Eect of an Interline Power Flow Controller (IPFC) on Damping Inter-area Oscillations in Interconnected Power Systems

Simulation and Comparison of DVR and DSTATCOM Used For Voltage Sag Mitigation at Distribution Side

Testing model data usability Excitation Systems PSS Limiters

Address for Correspondence

Transcription:

Transient Stability Improvement Of IEEE 9 Bus System With Shunt FACTS Device STATCOM P.P. Panchbhai 1, P.S.Vaidya 2 1Pratiksha P Panchbhai, Dept. of Electrical Engineering, G H Raisoni College of Engineering Nagpur, Maharashtra, India. E-mail: pratiksha.panchbhai@gmail.com 2Prajakta S Vaidya (Assistant Professor), Dept. of Electrical Engineering, G H Raisoni College of Engineering Nagpur, Maharashtra, India. E-mail: prajakta.vaidya@raisoni.net ------------------------------------------------------------------***--------------------------------------------------------------------- Abstract - This paper aims on improving the stability of a 9 bus power system under fault condition using a shunt FACTS device STATCOM or static synchronous compensator. In this paper an IEEE 9 bus system is modeled in MATLAB SIMULINK Software. STATCOM is a shunt FACTS device consisting of a voltage source inverter and a gate pulse generation circuit. It is connected to the transmission line through a coupling transformer. The results are obtained with STATCOM and without STATCOM. Analysis of the results shows that STATCOM has reduced the fault magnitude and has compensated the reactive power. It has also enhanced the voltage profile. Key Words: IEEE 9 bus system, Static Synchronous Compensator (STATCOM), Transient stability. 1. INTRODUCTION The existing power systems are big and are extensive and complex. Due to increase demand of power transfer the transmission lines are becoming overburdened. As the burden on the transmission line increases the transient stability of the system is affected and hence the system becomes unstable. Some of the parameters involve are the rotor speed, bus voltage, power flow and other system variables. Transient stability is an important aspect in designing of a power system. Power system stability is the ability of the system, for a given initial operating condition, to retain a normal state of equilibrium after being subjected to a disturbance [6]. In order to improve the voltage transfer across the system it is convenient to connect a FACTS device rather than installing new transmission lines. A shunt FACTS device STATCOM can be used to improve the power transfer capability of a system. STATCOM consists of a voltage source inverter and a dc capacitor. It is connected to the transmission line through a coupling transformer. 2. POWER SYSTEM STABILIZER The power system stabilizer (PSS) is a tool that measures improvements in system stability when added to a generator s automatic voltage regulator (AVR) and improves the power system stability. Power system stabilizer controls the excitation depending upon the fluctuations of generator output power. Although the output power of the generator is decided by the turbine mechanical torque the generator output power can be change by changing the excitation value. PSS detects the change in generator output power and controls the excitation value and reduces the power swing rapidly. The main function of power system stabilizer is to damp generator rotor oscillations which are oscillations due to electromechanical dynamics and are known as electromechanical oscillations [2]. The PSS is a feedback controller, part of the control system for a synchronous generator, which acts through the excitation system, adding a signal to modulate the field voltage. There are two types of stabilizer 1) Generic power system stabilizer model using the acceleration power (P a= difference between mechanical power P m and output electrical power P eo) and a 2) Multi-band power system stabilizer using the speed deviation (dw). In this paper Generic power system stabilizer block is connected to the synchronous machine. It consists of a general gain, low-pass filter, a washout highpass filter, phase-compensation system, and an output limiter. The input to the power system stabilizer is the synchronous machine speed deviation with respect to nominal (dw in pu) or the acceleration power (P a=p m-p e in pu). The output of pss is the stabilization voltage in pu which is connected as input to the excitation system. Block diagram of a power system stabilizer is shown in fig 1. It consists of a sensor block, overall gain, washout, lead lag filter 1 and 2 and a limiter. The washout block is used to reduce the over response of the damping during several events also it severs as a high pass filter which permits the signal associated with oscillations in speed of the rotor to pass as it is i.e remains unchanged but blocks the steady state change to modify the terminal voltages. The phase lead blocks are used to compensate for the lag between the PSS output and control action and the electric torque. PSS gain is 2016, IRJET Impact Factor value: 4.45 ISO 9001:2008 Certified Journal Page 128

important factor as the damping provided by PSS is directly proportional to the gain up to certain gain value after that the damping begins to decrease. i c current which is feed to three separated PI controllers. Here it is compared with the triangular wave and if the given condition is satisfied then pulses are generated which are the input to the VSI. Voltage Source Inverter has filters and IGBT/Diode which is use to generate the output voltage. 4. STANDARD IEEE 9 BUS POWER SYSTEM Fig-1: Power system stabilizer 3. STATCOM Fig-3: IEEE 9 bus power system without STATCOM Fig -2: Schematic diagram of basic STATCOM STATCOM is a static synchronous compensator, it is a shunt controller used to inject the current and control the voltage. It is connected to the transmission line through a coupling transformer. The shunt controller is use only to consume or to supply the reactive power. STATCOM consists of a voltage source inverter, which is used to convert dc voltage at its input terminal into three phase ac voltage. STATCOM can be applied with two basic control which includes (a) control of dc voltage across dc capacitor and (b) regulation of the ac voltage of power system at the bus bar, where STATCOM is installed. The basic principle of STATCOM involves the generation of controllable alternating current voltage source behind a transformer leakage reactance with a voltage source converter connected to a DC storage capacitor. The difference in voltage across the reactance produces active and reactive power exchanges between the STATCOM and the power system. STATCOM in this paper consists of a gate pulse generator circuit which is use to generate the gate pulses for the firing of the IGBT/Diode of the voltage source inverter. VSI is used to produce the output voltage. To the gate pulse generator input is given as a three phase current which is then converted to d-q frame of reference by parks transformation then its value is compared with the reference voltage by the PI controller and again it is converted to three phase i a, i b and Above fig shows MATLAB model of IEEE 9 bus power system without STATCOM. The system is prepared using the standard 9 bus system data [1]. Fig -4: IEEE 9 bus power system with STATCOM Above figure shows IEEE 9 bus system with STATCOM. The system is prepared in MATLAB SIMULINK software. Shunt FACTS device is connected between bus no. 7 and 8. The 2016, IRJET Impact Factor value: 4.45 ISO 9001:2008 Certified Journal Page 129

system consists of three generators, three transmission lines, three transformers and three loads. Synchronous machine are associated with the generator 2 and generator 3. Also the power system stabilizer is connected to the synchronous machine of generator 2 and 3. Bus 1 is the source bus, Bus 2 and 3 are the generator or the voltage bus as the generators are directly connected to these buses, and bus 4,5,6,7 8 and 9 are the load buses. 5. DATA SHEET OF 9 BUS SYSTEM Table-1: Prefault Network Admittance including load Equivalents Table-2: Generator Data Generator 1 2 3 Rated MVA 247.5 192.0 128.0 KV 16.5 18.0 13.8 Power Factor 1.0 0.85 0.85 Type Hydro Steam Steam Speed 180 r/min 3600r/min 3600 r/min Xd 0.1460 0.8958 1.3125 Xd 0.0608 0.1198 0.1813 Xq 0.0969 0.8645 1.2578 Xq 0.0969 0.1969 0.25 BUS No Impedance Admittance Xl (leakage) 0.336 0.0521 0.0742 Td0 8.96 6.00 5.89 Generator R X G D No 1 1-4 0 0.1184 0-8.4459 No 2 2-7 0 0.1823 0-5.4855 No 3 3-9 0 0.2399 0-4.1684 Transmission Line Shunt Admittance 4-5 0.0100 0.0850 1.3652-11.6041 4-6 0.0170 0.0920 1.9422-10.5107 5-7 0.0320 0.1610 1.1876-5.9751 6-9 0.0390 0.1700 1.2820-5.5882 7-8 0.0085 0.0720 1.6171-13.6980 8-9 0.0119 0.1008 1.1551-9.7843 Load A 5-0 1.2610-0.2634 Load B 6-0 0.8777-0.0346 Load C 8-0 0.9690-0.1601 4-0 0.1670 Tq0 0 0.535 0.600 Stored Energy at rated speed 2364 MW/s 640 MW/s 301 MW/s The generator internal voltage and their initial angles are given in pu by E 1 10 1.0566 2.2717 E 1.0502 19.7315 E 2 20 3 30 1.0170 13.1752 The system base is chosen to be 100 MVA and all the impedance values are taken corresponding to this base. Table 1 shows the equivalent shunt admittance for the load and the corresponding Y matrix is given in [1]. Table 2 gives the generator data were generator 1 is hydro and generator 2 and 3 are steam generator. The transmission line is having π connections. The system is first tested with fault and without the STATCOM connected. After that the results are obtain with fault and with the device connected in the system. Fault is created between bus no. 5 and 7. The parameters which are observed are line voltage, rotor speed, active power and the reactive power. 6. SIMULATION RESULTS 7-0 0.2275 9-0 0.2835 Fig-5: Rotor speed without STATCOM 2016, IRJET Impact Factor value: 4.45 ISO 9001:2008 Certified Journal Page 130

Fig-6: Rotor speed with STATCOM Fig-9: Reactive power without STATCOM From fig 5 the result shows that the rotor speed is fluctuate during the fault condition and fig 6 shows that STATCOM has improve the rotor speed to the value of almost 1 pu without any fluctuation even during the fault condition. Fig-10: Reactive power with STATCOM Fig-7: Active power without STATCOM Fig 9 and 10 shows the output reactive power without STATCOM and with STATCOM respectively the device has compensated the reactive power from 0.18 pu to 0.2 pu as STATCOM is use for reactive power compensation it has done so. Fig-8: Active power with STATCOM Fig-11: Line Voltage without STATCOM Fig 7 and 8 shows the output active power without device and with device respectively under fault condition the device has compensated the active power from 0.7 to 0.2 pu and also the magnitude of fault is reduced. Fig-12: Line Voltage with STATCOM 2016, IRJET Impact Factor value: 4.45 ISO 9001:2008 Certified Journal Page 131

Fig 11 and 12 shows the line voltage between bus 8 and bus 9 with and without STATCOM. Due to the presence of STATCOM the magnitude of fault has decrease a lot form 1.5 pu to 0.15 pu. 7. CONCLUSIONS Fault with FACTS Devices TCSC, STATCOM and UPFC (IJITR) international journal of innovative technology and research Volume No. 1, Issue No. 1, December January 2013 [10] Juan Segundo-Ramirez1 and A. Medina2, Analysis of Power Electronic Controllers in Electric Power Systems Using Simulink www.intechopen.com The simulation result shows that the device has enhanced the transmission capacity of line. The presence of STATCOM has reduced the fault magnitude as a result of which the main system losses have also been reduced. STATCOM is known for reactive power compensation and it has up to some extend shows compensation of power. In this paper simulation of STATCOM has verified that it can be applied to the power transmission line to compensate the reactive power and also to improve the voltage profile. It is use for the improvement of transient voltage behaviour of the power system. 8. REFERENCES [1] P.M. Anderson and A.A Fouad, Power system Control and Stability, Iowa State University Press. [2] ANDREA ANGEL ZEA, Power System Stabilizers for The Synchronous Generator Tuning and Performance Evaluation CHALMERS UNIVERSITY OF TECHNOLOGY Goteborg, Sweden 2013. [3] Sreevidya T.R, Dawnee S Optimal Interaction of PSS and SSSC in a Power System Network International Conference on Emerging Trends in Science, Engineering and Technolog IEEE 2012 [4] Prabha Kundur, Power System Stability and Control, Electric power research Institute, Tata McGraw-Hill Publishing Company Limited,Sixth Reprint 2008 [5] V.K.Ramachandaramurthy,R.N.Mukerjee,N.M. Mmuhamad Razali, Power System Stabilizer Placement and Tuning Methods for Inter-area Oscillation Damping First International Power and Energy Coference PECon 2006 November 28-29, 2006, Putrajaya, Malaysia [6] Swaroop Kumar.Nallagalva,Mukesh Kumar Kirar, Dr.Ganga Agnihotri, Transient Stability Analysis of the IEEE 9-Bus Electric Power System International Journal of Scientific Engineering and Technology, 01 July 2012 [7] Dr. S. Titus*, B.J.Vinothbabu**, I. Maria Anton Nishanth**, Power System Stability Enhancement under Three Phase Fault with FACTS Devices TCSC, STATCOM and UPFC International Journal of Scientific and Research Publications, Volume 3, Issue 3, March 2013 [8] Engr.Qazi Waqar Ali ¹, Prof.Dr.Azzam ul Asar, Smart Power Transmission System Using FACTS Device International Journal of Engineering & Computer Science IJECS-IJENS Vol:12 No:06 December 2012 [9] Dr. S. Titus, B.J.Vinothbabu, I. Maria Anton Nishanth, Power System Stability Enhancement Under Three Phase 2016, IRJET Impact Factor value: 4.45 ISO 9001:2008 Certified Journal Page 132