hinges
general specifications inge-to-door attachment Mounting plate-to-cabinet Press-in Use #6 wood screws Pre-attached dowels, install with lum MINIPRESS lum boring pattern Door-to-cabinet attachment Door 9.5 C Ø35 C Cup centerpoint 20.5 21.5 22.5 23.5 24.5 25.5 13/16" 27/" 7/8" 15/16" 31/" 1" 3 4 5 6 7 8 45 Ø8 ore distance only for use with select lum hinges Cup centerpoint is the MINIPRESS or MINIDRILL fence depth position. o install slide hinge on to the mounting plate, tighten rear fixing screw. Loosen rear fixing screw and pull hinge forward to remove. hree-dimensional adjustment Side adjustment eight adjustment Depth adjustment Rotate front screw to increase or decrease door overlay. Range = ±2 mm Loosen screw(s) on the mounting plate. Adjust door to position and tighten screws. Range = ±3 mm Loosen back screw. Adjust door to position and tighten screw. Range = ±2 mm wo piece mounting plate One piece mounting plate inge dimension abbreviations Minimum reveal inges per door X W R OL = oring distance = Mounting plate height OL = Door overlay P = Door protrusion (at max opening) S P R = Reveal S = inge arm protrusion = Door thickness W = Side panel width X = Fixed cup distance 19 1 rad (1/ ") Minimum Reveal A minimum reveal per door is required to keep the door from binding and varies depending on door thickness (see Minimum reveal table for each hinge). Minimum reveal based on outside door edge with radius of 1 (1/"). X = Door height 100" Y = Number of hinges his chart can serve as a guide for determining the number of hinges per door. Note that door weight can also determine the number of hinges required. 80" 60" 40" 20" X Y 15 lb. 15-30 lb. 30-45 lb. 45-60 lb. 2 3 4 5 he distance between the top and bottom hinges must be greater than the width of the door. 53
100 hinges 100 Frame cabinet applications door Features - 100 opening angle - All metal hinge, nickel-plated - hree-dimensional adjustment - Slide-on hinge arm Cover caps page 59 Mounting plates pages 57-58 Panel cabinet applications door 16 18 19 20 22 24 26 Door thickness ore See back cover fold out for more specifications Straight-arm hinges Free swing 91M2550 90M2550 Press-in 91M2580 90M2580 Minimum Reveal Minimum reveal table 0.5 0.9 1.1 1.4 2.3 3.6 5.2 3 Cross-refer- 0.5 0.8 1.0 1.3 2.0 3.3 4.8 4 0.4 0.8 1.0 1.2 1.8 3.0 4.4 5 0.4 0.8 0.9 1.1 1.7 2.8 4.1 6 ence the door thickness and bore distance to assure that doors won t bind when opened. table 10.5 58 58 10.5 0 14 15 16 17 9 20 3 12 13 14 12 23 6 8 9 10 15 26 9 5 6 7 8 18 29 3 4 5 6 P S Plate ore distance Clearances fixed distance NOE: 9 plate only available for panel cabinets Partial overlay door win overlay doors alf-cranked hinges (9.5 mm) 91M2650 Press-in 91M2680 table Partial overlay 0 4.5 5.5 6.5 7.5 18.5 30 10.5 58 58 10.5 Reveal 3 4 5 6 P S Plate ore distance Clearances 1.5 fixed distance Reveal table 7 5 3 1 16 win overlay 0 10 8 6 4 19 18.5 30 13 9 7 22 3 4 5 6 W P S Plate ore distance Panel Clearances Inset door Full-cranked hinges (18 mm) 91M2750 Press-in 91M2780 60 + 38.5 Reveal table 0 4 3 2 1 27 38 3 4 5 6 P S Plate ore distance Clearances - 7 fixed distance 10.5 Reveal 54
170 hinges 170 Frame cabinet applications door Features - 170 opening angle - All metal hinge, nickel-plated - hree-dimensional adjustment - Slide-on hinge arm Cover caps page 59 Mounting plates pages 57-58 Panel cabinet applications door W Minimum Reveal Minimum reveal table 0 0 0 0 0.2 2.2 4.2 3 Cross-reference 0 0 0 0 0 1.4 3.8 4 the door thickness and 0 0 0 0 0.9 2.7 5 bore distance to assure that 0 0 0 0 0 0 2.2 6 doors won t 0 0 0 0 0 0 1.7 7 bind when opened. 0 0 0 0 0 0 1.3 8 16 18 19 20 22 24 26 Door thickness ore See back cover fold out for more specifications Straight-arm hinges 91A6550 Press-in 18 91A6580 69 69 table 0 14 15 16 17 18 19 1.5 65 3 12 13 14 15 16 4.5 68 6 8 9 10 12 13 7.5 71 9 5 6 7 8 9 10 10.5 74 3 4 5 6 7 8 P S Plate ore distance Clearances fixed distance NOE: 9 plate only available for panel cabinets Partial overlay door win overlay doors W alf-cranked hinges (9.5 mm) 91A6650 Press-in 18 91A6680 table Partial overlay 0 4.5 5.5 6.5 7.5 8.5 9.5 75 69 69 3 4 5 6 7 8 P S Plate ore distance Clearances 1.5 fixed distance Reveal table win overlay Reveal 0 7 5 3 1 - - 16 10 8 6 4 2 0 19 13 9 7 5 3 22 75 3 4 5 6 7 8 W P S Plate ore distance Panel Clearances Inset door Use half-cranked hinge Any 9 mm plate alf-cranked hinges (9.5 mm) 91A6650 Press-in 18 91A6680 71 + 38.5 Reveal table 9 4.5 3.5 2.5 1.5 0.5-20 84 3 4 5 6 7 8 P S Plate ore distance Clearances - 7.5 fixed distance Reveal 55
56
mounting plates One piece wing mounting plate Cover caps - Add additional page 61 wood screw if used with wide angle hinges Mounting plates pages 59-60 - Steel, nickel-plated - Attached with wood screws #6 x 5/8" - eight adjustment ±3 mm Wood screws () eight 0 606N or 606P 193L6100 One piece wing mounting plate 8.5 - Steel, nickel-plated - Attached with pre-mounted system screws Ø5 mm (668.1450.E) - eight adjustment ±3 mm - Add additional wood screw if used with wide angled hinges 5 wo piece mounting plate System screws () eight 0 Pre-mounted 193L8100 - Zinc die-cast, nickel-plated - Attached with wood screws #6 x 5/8" - eight adjustment ±2 mm - Add additional wood screw if used with wide angled hinges Wood screws () eight 0 () eight 9 606N or 606P 1957100 1957190 57
mounting plates wo piece wing mounting plate - eight adjustment ±2 mm Cover caps - Add additional page wood 61 screw if used with wide angle hinges Mounting plates pages 59-60 5.5 - Zinc die-cast, nickel-plated - Attached with #7 x 9/16" wood screw or Ø6 x 14.5 mm system screws Wood screw or System screws () eight 0 707N 661.1450.G 1959100 Face frame adapter plate - Zinc die-cast, nickel-plated - Attached with wood screws #7 x 3/4" - eight adjustment ±2 mm - Use of the PlateMate recommended for proper installation (see page 78) Recessed frame adapter plate 12.5 Wood screws () eight 0 () eight 6 7074N 198.6600.22 198.6660.22 8.5 - Zinc die-cast, nickel-plated - Attached with wood screws #6 x 5/8" - eight and side adjustment ±2 mm - For overlays of 24 mm (15/16") to 27 mm (1-1/16") 15 35 45 Wood screw () eight 0 606N or 606P 199.0100.02 58
cover caps a Nylon (black or white) 90M2103 90M2103.22 (lum logo) 80.6107 94M03 cover caps Nylon 100 hinges Straight-arm 90M2103 Cranked-arm 94M03 170 hinges 80.6107 lind corner hinges Straight-arm 90M2103 NOE: Custom logo available in nylon (black or white). Consult your lum representative for minimum quantities and lead times on custom logos. 59