CP SYSTEM CP LED Find additional images and information at alwusa.com/cp
1. BASE MODEL CPP 1 Pendant; four sides and bottom illuminated CPC 1 Ceiling-Mount; four sides and bottom illuminated CPW 1 Wall Sconce; three sides plus top and bottom illuminated When specified with an Accent Downlight, bottom panel will be aluminum and non-illuminated Page 2 of 5 Type: 2.SIZE A 12"H x 28"W x 12"D B 12"H x "W x 12"D C 12"H x 52"W x 18"D D 3 12"H x 52"W x 52"D F 28"H x 12"W x 12"D H "H x 12"W x 12"D J 52"H x 12"W x 12"D L "H x "W x 28"D Custom Dimensions 2 (Enter H"xW"xD"; ex: 48"x24"x8") NOTE: Typical output is 600-900 delivered lm/cuft and varies with base model and size specified. Consult factory for specifics or when consistency is required across different models and/or sizes. 2 Custom sizes must fall within these ranges: = 8"-96", Width 8"-52", Depth 8"-36" 3 Not available with CPW 3. LAMPING DECOR RGB 4 RGBW 4 Pair lamping with CCT (where applicable), ex: DECOR/ Decorative constant voltage LED, raw 439 lm/ft, 5.9 W/lf Color-changing RGB LED, 5 W/lf Color-changing RGB plus White ( CCT) LED, 5 W/lf 4 DMX driver recommended; controller not included 4. DRIVER Pair driver with dimming level (where applicable), ex: 0/10V/S 0/10V/S 0-10V dimming down to 10% DALI DALI dimming to 0% DMX DMX dimming to 0% ECOSYS1 Lutron Hi-lume 1% EcoSystem, constant current or constant voltage ECOSYS5 Lutron 5-Series 5% EcoSystem, constant current 5. LENS LN WHT Linen-colored, 1/8" acrylic White-white, 1/8" acrylics Consult factory for additional lens options including Lumicor and 3Form acrylics 6. [CODE] None. Select when specifying only Primary Lamping Complete Accent Downlight Worksheet on Page 4 to determine code
7. DRIVER 0/10V/ Page 3 of 5 Pair driver with dimming level (where applicable), ex: 0/10V/S None. Select "None" when specifying only Primary Lamping 0-10V dimming S Standard dimming to 10% 1% Dimming to 1% 0% Premium dimming to 0% DALI DALI dimming to 0% DMX DMX dimming to 0% ECOSYS1 Lutron Hi-lume 1% EcoSystem, constant current or constant voltage ECOSYS5 Lutron 5-Series 5% EcoSystem, constant current 8. ACCESSORY None HEX Hexcell louver SNT Snoot HEXCELL LOUVER SNOOT 9. QUANTITY None. Select "None" when specifying only Primary Lamping Enter total quantity downlights per unit For total quantity considerations, please note each downlight requires roughly 8" of width and 8" of depth in fixture. Consult factory for specifics for special requests 10. FINISH AL BK BRS SV WH WH/AM RAL/ Standard, natural Ultimatte aluminum Black powdercoat Brass metallic powdercoat Silver powdercoat White powdercoat White antimicrobial powdercoat for healthcare environments Specify RAL powdercoat code (ex: #RAL/3003) 11. VOLTAGE UNV Universal voltage 347 5 347 volt 5 Driver options may be limited with 347 voltage. Consult factory. 12. ADDITIONAL OPTIONS COMBO EMC 6 EMB 6 ENLGHT/ 7,8 OS 8 PH 8 SB None Combination 4.5" canopies at feed locations with both power feed and suspension mounting hardware Emergency circuit Emergency battery pack Enlighted 0-10V remoted smart sensor (occupancy, daylight, networking and more) 0-10V remoted occupancy sensor 0-10V remoted photocell/daylight sensor Seismic bracing 6 Consult factory for available options 7 Enlighted Gateway and Energy Manager (by others) plus programming required. Learn more at enlightedinc.com. 8 Compatible with 0-10V driver only. Contact factory for alternative options.
DIMENSION PLANES & MOUNTING OPTIONS Page 4 of 5 Width CEILING-MOUNT CPC Width HEIGHT PENDANT CPP DEPTH Depth WIDTH WALL SCONCE CPW WORKSHEET SPOTLIGHTS DL800 DL1000 DL1500 SPOT DELIVERED LUMENS (LM) WATTS (W) EFFICACY (LM/W) CRI BEAM SPREAD (DEGREES) SELECT ONE ONLY CCT SELECT ONE ONLY COMPLETE CODE Compile bold codes, separate each with a slash and enter on Page 2, Section 6. ex: DL1500// DL800 800 4.8 167 80 DL1000 1000 6.1 164 80 DL1500 1500 9.7 155 80
FRAME 3/4" frame constructed of 100% recyclable, extruded architectural grade T6061 aluminum with.08" minimum wall thickness. ELECTRICAL LED drivers are Class 2. ETL listed for indoor location only. LENS OPTIONS Page 5 of 5 Choose from a 1/8" linen-colored, off-white acrylic lens with slightly textured look or a 1/8" white-white opal acrylic lens. Contact factory for additional options including Lumicor and 3Form acrylics. EMERGENCY Luminaires can be wired for emergency circuit and/or emergency battery backup. Consult factory for details. SUSPENSION HARDWARE Linen-colored LN White-white WHT FINISH CEILING HARDWARE (1) 4.5" canopy per power feed location, (1) bullet mount, (1) 8' aircraft cable and (1) 2" canopy (for use with T-bar mounting) per suspension point OPTIONS ADJUSTABLE GRIP-LOCK Adjustable aircraft cable grip-locks attached to topside of luminaire provide secure suspension points Canopy finish is always white. Contact factory for alternate color. Standard finish is "Ultimatte" aluminum a smooth, clean and durable finish achieved from a deepetch and two-step clear anodizing process. White, black, silver, brass and color RAL powdercoat options also available. For healthcare environments, a white antimicrobial finish (WH/AM) is also an option. ALUMINUM AL WHITE WH & WH/AM BLACK BK Eye Bolt (By Others) Gripper w/hook 2-Cable Clamp SILVER SV BRASS BRS COLOR RAL Aircraft Cable SEISMIC BRACING Add-on hardward includes cable gripper with hook, 2-cable clamp and specified length of aircraft cable per suspension point COMBO CANOPY Choose COMBO to specfiy 4.5" canopies at feed locations with power feed and aircraft cable suspension mounting OPERATING TEMPERATURE Luminaire should be installed and operated ONLY in environments where the ambient temperature ranges from -4 F (-20 C) to 122 F (50 C). Operating the luminaire in environments outside the listed temperature range voids the warranty AND may damage the product or adversely impact lamp life, lumen output and color consistency.