Power Distribution Blocks with Short-Circuit Current Ratings General Information: The requirements of the 005 National Electric Code (NEC) and UL508A now require many electrical panels to carry a Short Circuit Current Rating (SCCR). Analyzing the SCCR of individual components and overcurrent protection devices is a method of determining the SCCR of an electrical assembly. Equipment with low SCCR s are limited to locations where only low-level short-circuit current is available. By replacing a low-rated power distribution block with a Marathon high SCCR power distribution block, an assembly can achieve a higher SCCR for more installation flexibility. Short-Circuit Current Ratings Marathon s Power Distribution Blocks are standard products that have been used in electrical control panels for over 35 years. These blocks have now been tested and approved for higher SCCR. The higher ratings are based on proper wire sizes and the appropriate circuit protection device (fuses or circuit breakers). UL508A does allow default SCCR for Power Distribution Blocks of 0,000A with no additional testing. Marathon s Power Distribution Blocks are recognized under UL Standard 059 (UL File # E80) and have been investigated by UL for Short Circuit Current Rating under category XCFR; Terminal Blocks-Component. In addition, Marathon offers Power Distribution Blocks that are listed to UL 953 (UL File # E3090). The feeder spacing requirements of UL508A are achieved with these blocks. Phone: 800.89.0 - Fax: 888.73.773 - Web: www.clrwtr.com - Email: info@clrwtr.com
UL Listed Power Distribution Blocks UL Listed The requirements of the 005 National Electric Code (NEC) and UL508A now require many electrical panels to carry a Short Circuit Current Rating (SCCR). These new Power Distribution Blocks are listed to UL953. The feeder spacing requirements of UL508A are achieved with these blocks. Housings, Thermoplastic, UL 9 V-0, RTI 5 o C Insulator Base Plate, Laminate, UL 9 V-0, RTI 30 o C Wire s - Tin Plated Aluminum, Rated for Copper or Aluminum Wire ( & ) Short Circuit Current Rating up to 00kA (00kA SCCR Rating with copper conductors only. Requires specific over-current protection device.) Attached hinged cover UL 508A Feeder Circuit Terminal Spacing for up to 00 Volts Rated up to 335 Amp, 00 Volts Line side conductor up to 00 kcmil Distribution, up to twelve conductors per pole Investigated to UL 953 UL Category and File: QPQS.E3090 Current Amps Material Config. Config. SCCR RMS Sym Amps 00 volt Max FPB3570 75 35 Aluminum /0 - # # - # 00,000 FPB357 75 35 Aluminum /0 - # /0 - # 00,000 FPB357 75 35 Aluminum /0 - # / - 0 stud 00,000 FPB3580 75 35 Aluminum /0 - # # - # 00,000 FPB33553 335 70 Aluminum 00 kcmil - # # - # 00,000 FPB33588 335 335 Aluminum 00 kcmil - # /0 - # # - # 3 00,000 FPB33595 335 335 Aluminum 00 kcmil - # # - # 00,000 See page 37 for dimensional information. Phone: 800.89.0 - Fax: 888.73.773 - Web: www.clrwtr.com - Email: info@clrwtr.com
UL Listed Power Distribution Blocks FPB3XXX.5 08 PRODUCT & SCCR INFORMATION PROVIDED ON SIDES OF BLOCK.38 9.5.5 57. Ø. [5.] THRU CBØ.50 X.38 DP X [.7 X 9.7 DP].3 33.3.3.3 3.00 7. UL Listed 3.8 80.8 w/ Cover 3.05 77.3 w/o Cover FPB33XXX.38 9.5.38 3.9.00 5. 3.5 8.5 5.50 39.7.75 0. PRODUCT & SCCR INFORMATION PROVIDED ON SIDES OF BLOCK Ø. [5.] THRU CBØ.50 X.38 DP X [.7 X 9.7 DP]. 0.5 w/ Cover 3.9 00.5 w/o Cover Phone: 800.89.0 - Fax: 888.73.773 - Web: www.clrwtr.com - Email: info@clrwtr.com
UL Listed Enclosed UL Listed Enclosed Electrical 00 Volts AC/DC + 000 Volts (IEC) Up to 5 Amps # to # Mechanical Base, Gray Thermoplastic, 5 o C (57 o F) (UL RTI) Flammability, UL 9 V-0 Mounting: DIN or panel mount Standards UL Listed File No. QPQS.E3090 (UL 953) CSA Certified File No. LR97 (CSA C- No. 58) (Component IEC 097-7-) IEC 059, IP-0 Accessories (consult Cust. Service) White Markers to Identify Circuits DIN Rail for Mounting Option End Piece for DIN Rail (MSK35) Shown left to right: EPBAD, EPBAD Amperage Wire 75 o C SCCR, RMS SYM Amps 00 Volt Max EPBAD 5 # - # AWG 35 -.5 mm # - # AWG 35 -.5 mm 00,000 EPBAD 5 # - # AWG 35 -.5 mm #0 - # AWG -.5 mm 5,000 Ordering Code: EPB A D Note: Material: A - Aluminum rated copper or aluminum wire ) The ampacities are based on Table 30- of the NEC. ) The connectors were tested and approved per UL 8 A/B. 3) For detailed SCCR information with fuses and circuit breakers, please refer to datasheets on MarathonSP website. D - Mount on 35 mm DIN rail or flat panel. 05. - () # to () # - () # to () #0 Min. Enclosure Size: x x in See Data-sheet for addtional ratings AC/DC 75 Str./Sol. BLOCK - 3JUU 5A 00V POWER DISTRIBUTION IEC 097-7- LISTED SLOT.3 X., [7.9 X 5.3] FOR USE WITH #0 MTG SCREW 5/3 [mm] HEX DRIVE DOVETAIL FEATURES ON SIDES OF BLOCK FOR MULTI-LINE STACK-UP (SEE NOTE-) 5/ [mm] HEX DRIVE TYP. FOR SNAP-IN MARKER CARDS.37 9.5 3.75 95.3 STACK-UP DIMENSIONS (If Dovetail is used for Mulit-Line).9 37.9. 5.8 SCCR RATINGS & ENGLISH & METRIC WIRE RANGES W/TORQUE PRINTED ON OPPOSITE SIDE OF BLOCK..0.75.75. 9 8.9 TYP..9 37.8 Phone: 800.89.0 - Fax: 888.73.773 - Web: www.clrwtr.com - Email: info@clrwtr.com
Enclosed COMING SOON: UL LISTED ENCLOSED POWER BLOCKS Electrical 00 Volts AC/DC + (IEC - 90 Volts AC/DC) Up to 50 Amps /0 to 00 kcmil Mechanical Base, Gray Thermoplastic, 5 o C (UL RTI) Flammability, UL 9 V-0 Mounting: DIN or panel mount Standards UL Recognized File No. XCFR.E80 (UL 059) CSA Certified File No. LR97 (CSA C. No. 58) (IEC 097-7-) IEC 059, IP-0 Accessories (consult Cust. Service) White Markers to Identify Circuits Black Thermoplastic Safety Plugs Feed Spacing UL508A Adapter Plate EPBXD Amperage Wire 75 o C 75 /0 - # AWG 70 -.5 mm Multiple Wire Ratings Copper Stranded Wire Only # opening: /0 opening: () # AWG () # AWG () #8 AWG () # AWG ( to ) #0 AWG () #8 AWG ( to ) # AWG () #0 AWG ( to ) # AWG () # AWG Wire Hole Size Conductor opening: # - # AWG.38 /0 - # AWG.50 50 kcmil - # AWG.7 00 kcmil - # AWG.9 Config. () # AWG Diameter of opening: /0 - # AWG 70 -.5 mm Shown left to right: EPBAD7, EPBAD7 EPBAD, EPBAD Config. SCCR, RMS SYM Amps 00 Volt Max 00,000 Enclosed EPBXD 75 /0 - # AWG 70 -.5 mm # - # AWG 35 -.5 mm 00,000 EPBXD7 0,000 50 kcmil - # AWG 50 kcmil - # AWG 50 0 - mm 0 - mm 50,000 - EPBXP7 00,000 00 kcmil - # AWG EPBXD7 0,000 85 - mm # - # 335 8 /0 - # AWG 35 -.5mm EPBXP7 00,000 70 -.5 mm Ordering Code: Note: ) The ampacities are based on Table 30- of the NEC. EPB A D Material: A - Aluminum rated copper or aluminum wire C - Copper rated copper D - Mount on 35 mm DIN rail or flat panel P - Flat panel (for 7 and 7 - () /0 to () /0 - () /0 to () # 7 - () 50 kcmil to () 50 kcmil 7 - () 00 kcmil to () /0 to (8) # See page 0 for dimensional information. Phone: 800.89.0 - Fax: 888.73.773 - Web: www.clrwtr.com - Email: info@clrwtr.com
Enclosed Power Block Dimensions EPBXD & EPBXD Enclosed. 0.0 3.7 [95.58].0 5.93.53.9 SLOT.50 X.5 [.70 X.35] 3.00 7.0 STACK UP DIMENSIONS (IF DOVETAIL IS USED FOR MULTI-LINE) 3.8 97.5.5.97 TYP. FOR SNAP-IN MARKER CARDS...33 33.78.8 [3.9] TYP..5.97 EPBXX7 & EPBXX7 STACK UP DIMENSIONS (IF DOVETAIL IS USED FOR MULTI-LINE PB) 3.9 83.7 3. 79.79 SLOT.5 X.7 [3. X.8]..73. 9.0.73 [.5].39 [.] 3.75 [95.5] TYP. FOR SNAP-IN MARKER CARDS. [8.8].7 57.58. 5.3..73 Phone: 800.89.0 - Fax: 888.73.773 - Web: www.clrwtr.com - Email: info@clrwtr.com
Power Terminal Blocks General Information: Barrier Style Power Terminal Blocks are available in eight sizes. They are identified by the first three digits of the catalog number. The 0,, 3, and 5 series are manufactured with general purpose phenolic rated at 50 o C. The, 3 and 33 series are manufactured with high impact thermoplastic rated at 5 o C. Enclosed touch proof power terminal blocks (EPB series) are available in three sizes (one listed, two recognized). Wire Hole Size: Conductor Opening Diameter of Opening English Metric Inch Metric #0 AWG.58.0 # AWG 5.50. # AWG 35.35 * 7.9 /0 50.0 0.3 /0 70.38 *. 3/0 95.53 3.5 50 kcmil 0.30 *.0 350 kcmil 85.78 8. 00 kcmil -.79 * - 500 kcmil 0.875. 00 kcmil 300.938 3.8 750 kcmil -.5-000 kcmil -.50 - * Enclosed blocks have larger openings (see page 39) Ratings and Standards: The voltage ratings of terminal blocks are based upon the minimum spacing between electrically conductive parts line to line through air and over surface and line to ground through air and over surface. Class A Service equipment including deadfront switchboards, panel boards, service entrance devices. Class B Commercial appliances including business equipment, electronic data processing equipment and the like. Class C General industrial and machine tool controls which can be further defined as equipment falling under UL 508. Ratings based on UL 059 may be higher in some cases depending on application. Spacing Requirements*: Voltage Thru Air Over Surface 5-50.500.750 Class A 5-300.750.50 30-00.000.000 5-50.03.03 Class B 5-300.09.09 30-00.375.500 5-50.5.50 Class C 5-300.50.375 30-00.375.500 *In Inches Applications: Designed for use with solar, wind, alternate energy, transportation, heating, air conditioning and refrigeration, elevator systems, material handling equipment, control panels, motor control, switchgear and any area where power needs to be distributed to more than one load. Phone: 800.89.0 - Fax: 888.73.773 - Web: www.clrwtr.com - Email: info@clrwtr.com
00 Volts AC/DC Up to 000 Volts AC/DC ( ) +, High Conductive Aluminum, Tin Plated, Rated for Copper and Aluminum Wire, High Conductive Copper, Tin Plated, Rated for Copper Wire Only Amp Rating Based on NEC Table 30- Using 75 o C Copper Wire UL Recognized File No. XCFR.E80 CSA Certified File No. LR97 Power Distribution Blocks 3570 00 ** rated for #- AWG are multiple wire rated: () #0 Str, ( to ) # Str, and ( to ) # Str. *** rated for #- AWG are multiple wire rated: () #8 Str, () #0 Str, () # Str, and () # Str. Hinge Cover Poles (X) MATERI Amps Insulator Conn. Replace X with # of poles (0 = Adder) X03 //3/ 0 # - # AWG #0 - # AWG X00 //3/ 5 # - # AWG #0 - # AWG 3X570 0///3 75 /0 - # AWG # - # AWG** X570 //3 75 /0 - # AWG # - # AWG** 3X580 0///3 75 /0 - # AWG # - # AWG** 0X0 /3 75 /0 - # AWG # - # AWG** 0X0 /3 75 /0 - # AWG # - # AWG** 3X970 0///3 75 /0 - # AWG # - # AWG** X970 //3 75 /0 - # AWG # - # AWG** 0X0 /3 30 350 kcmil - # AWG # - # AWG 33X55 //3 30 350 kcmil - # AWG /0 - # AWG = Block is also available with hinge cover attached - include at end of part number when ordering (not available on Adder blocks) - See page 55 for available covers See pages 5-5 for dimensional information Phone: 800.89.0 - Fax: 888.73.773 - Web: www.clrwtr.com - Email: info@clrwtr.com
Power Distribution Blocks (cont.) 00 Volts AC/DC Up to 000 Volts AC/DC ( ) +, High Conductive Aluminum, Tin Plated, Rated for Copper and Aluminum Wire, High Conductive Copper, Tin Plated, Rated for Copper Wire Only Amp Rating Based on NEC Table 30- Using 75 o C Copper Wire UL Recognized File No. XCFR.E80 CSA Certified File No. LR97 350 33553 ** rated for #- AWG are multiple wire rated: () #0 Str, ( to ) # Str, and ( to ) # Str. *** rated for #- AWG are multiple wire rated: () #8 Str, () #0 Str, () # Str, and () # Str. Hinge Cover Poles (X) MATERI Amps Insulator Conn. Replace X with # of poles X0 //3 335 00 kcmil - # AWG # - # AWG 3X55 //3 335 00 kcmil - # AWG # - # AWG 3X553 //3 335 00 kcmil - # AWG # - # AWG X50 //3 335 00 kcmil - # AWG # - # AWG 8 33X55 //3 335 00 kcmil - # AWG # - # AWG*** 3X555 //3 350 /0 - # AWG # - # AWG** 33X555 //3 350 /0 - # AWG # - # AWG** 3X955 //3 350 /0 - # AWG # - # AWG** 33X955 //3 350 /0 - # AWG # - # AWG** 3X953 //3 380 500 kcmil - # AWG # - # AWG 33X953 //3 380 500 kcmil - # AWG # - # AWG*** = Block is also available with hinge cover attached - include at end of part number when ordering (not available on Adder blocks) - See page 55 for available covers See pages 5-5 for dimensional information Phone: 800.89.0 - Fax: 888.73.773 - Web: www.clrwtr.com - Email: info@clrwtr.com
Power Distribution Blocks (cont.) 00 Volts AC/DC Up to 000 Volts AC/DC ( ) +, High Conductive Aluminum, Tin Plated, Rated for Copper and Aluminum Wire, High Conductive Copper, Tin Plated, Rated for Copper Wire Only Amp Rating Based on NEC Table 30- Using 75 o C Copper Wire UL Recognized File No. XCFR.E80 CSA Certified File No. LR97 333588 333595 ** rated for #- AWG are multiple wire rated: () #0 Str, ( to ) # Str, and ( to ) # Str. *** rated for #- AWG are multiple wire rated: () #8 Str, () #0 Str, () # Str, and () # Str. Hinge Cover Poles (X) MATERI Amps Insulator Conn. Replace X with # of poles X55 //3 380 500 kcmil - # AWG # - # AWG 5X579 //3 380 500 kcmil - # AWG /0 - # AWG 33X587 //3 380 500 kcmil - # AWG # - # AWG*** 350 kcmil - # AWG 3 3X587 //3 380 500 kcmil - # AWG # - # AWG*** 350 kcmil - # AWG 3 5X59 //3 380 500 kcmil - # AWG # - # AWG 8 5X55 //3 380 500 kcmil - # AWG # - # AWG 33X588 //3 0 00 kcmil - # AWG # - # AWG*** /0 - # AWG 3 33X595 //3 0 00 kcmil - # AWG - # AWG** 33X585 //3 0 00 kcmil - # AWG - # AWG*** 8 33X575 //3 0 00 kcmil - # AWG /0 - # AWG 33X55 //3 0 00 kcmil - # AWG 50 kcmil - # AWG = Block is also available with hinge cover attached - include at end of part number when ordering - See page 55 for available covers See pages 5-5 for dimensional information Phone: 800.89.0 - Fax: 888.73.773 - Web: www.clrwtr.com - Email: info@clrwtr.com
Power Distribution Blocks (cont.) 00 Volts AC/DC Up to 000 Volts AC/DC ( ) +, High Conductive Aluminum, Tin Plated, Rated for Copper and Aluminum Wire, High Conductive Copper, Tin Plated, Rated for Copper Wire Only Amp Rating Based on NEC Table 30- Using 75 o C Copper Wire UL Recognized File No. XCFR.E80 CSA Certified File No. LR97 33359 333598 ** rated for #- AWG are multiple wire rated: () #0 Str, ( to ) # Str, and ( to ) # Str. *** rated for #- AWG are multiple wire rated: () #8 Str, () #0 Str, () # Str, and () # Str. Hinge Poles Cover (X) MATERI Amps Insulator Conn. Replace X with # of poles 33X59 //3 50 50 kcmil - /0 AWG # - # AWG** 33X597 //3 50 50 kcmil - /0 AWG # - # AWG*** 8 33X598 //3 50 50 kcmil - /0 AWG /0 - # AWG 5X587 //3 90 500 kcmil - # AWG 350 kcmil - # AWG /0 - # AWG 5X59 //3 70 500 kcmil - # AWG # - # AWG** 5X58 //3 70 500 kcmil - # AWG /0 - # AWG 8 5X99 //3 70 500 kcmil - # AWG # - # AWG 5X98 //3 70 500 kcmil - # AWG /0 - # AWG 8 5X08 //3 70 500 kcmil - # AWG # - # AWG 5X //3 80 00 kcmil - # AWG 3/0 - # AWG # - # AWG** 530* 80 500 kcmil - # AWG /0 - # AWG 8 = Block is also available with hinge cover attached - include at end of part number when ordering - See page 55 for available covers See pages 5-5 for dimensional information *Special one-pole block. Apply Power Block Dimensions for 5 Series block on page 5 (3 pole). Phone: 800.89.0 - Fax: 888.73.773 - Web: www.clrwtr.com - Email: info@clrwtr.com
00 Volts AC/DC Up to 000 Volts AC/DC ( ) +, High Conductive Aluminum, Tin Plated, Rated for Copper and Aluminum Wire, High Conductive Copper, Tin Plated, Rated for Copper Wire Only Amp Rating Based on NEC Table 30- Using 75 o C Copper Wire UL Recognized File No. XCFR.E80 CSA Certified File No. LR97 Power Splicer Blocks 3397 3357 Hinge Cover Poles (X) MATERI Amps Insulator Conn. Replace X with # of poles (0 = Adder) X300 //3/ 5 # - # AWG # - # AWG X55 //3 5 # - # AWG # - # AWG 3X57 0///3 75 /0 - # AWG /0 - # AWG X57 //3 75 /0 - # AWG /0 - # AWG 3X97 0///3 75 /0 - # AWG /0 - # AWG X //3 75 /0 - # AWG /0 - # AWG 3X //3 55 50 kcmil - # AWG 50 kcmil - # AWG 0X80 /3 55 50 kcmil - # AWG 50 kcmil - # AWG 3X3 //3 55 50 kcmil - # AWG 50 kcmil - # AWG 0X303 /3 30 350 kcmil - # AWG 350 kcmil - # AWG 3X //3 30 350 kcmil - # AWG 350 kcmil - # AWG = Block is also available with hinge cover attached - include at end of part number when ordering (not available on Adder blocks) - See page 55 for available covers See pages 5-5 for dimensional information Phone: 800.89.0 - Fax: 888.73.773 - Web: www.clrwtr.com - Email: info@clrwtr.com
Power Splicer Blocks (cont.) 00 Volts AC/DC Up to 000 Volts AC/DC ( ) +, High Conductive Aluminum, Tin Plated, Rated for Copper and Aluminum Wire, High Conductive Copper, Tin Plated, Rated for Copper Wire Only Amp Rating Based on NEC Table 30- Using 75 o C Copper Wire UL Recognized File No. XCFR.E80 CSA Certified File No. LR97 3557 539 Hinge Cover Poles (X) MATERI Amps Insulator Conn. Replace X with # of poles 33X //3 30 350 kcmil - # AWG 350 kcmil - # AWG 33X305 //3 350 /0 - # AWG /0 - # AWG 3X30 //3 350 /0 - # AWG /0 - # AWG X557 //3 0 00 kcmil - # AWG 00 kcmil - # AWG 33X30 //3 0 00 kcmil - # AWG 00 kcmil - # AWG 33X30 //3 50 50 kcmil - /0 AWG 50 kcmil - /0 AWG 5X9 //3 0 350 kcmil - # AWG 350 kcmil - # AWG 5X30 //3 70 500 kcmil - # AWG 500 kcmil - # AWG = Block is also available with hinge cover attached - include at end of part number when ordering - See page 55 for available covers See pages 5-5 for dimensional information Phone: 800.89.0 - Fax: 888.73.773 - Web: www.clrwtr.com - Email: info@clrwtr.com
00 Volts AC/DC Up to 000 Volts AC/DC ( ) +, High Conductive Copper, Tin Plated Stud, Brass, Tin Plated, Metric (M) Studs, Steel Suitable for Compression Wire Lugs UL Recognized File No. XCFR.E80 CSA Certified File No. LR97 Power Stud Blocks 3 33 Replace X with # of poles (0 = Adder) Hinge Cover Poles (X) MATERI Amps Insulator Conn. 3X 0///3 00 /-0 x 9/ /-0 x 9/ 3X 0///3 00 M x 5 M x 5 X3 //3 00 /-0 Screw /-0 Screw X //3 00 /-0 x 9/ /-0 x 9/ 3X53 //3 30 3/8- x 3/ 3/8- x 3/ 3X5 //3 30 3/8- x 3/ /-0 x 3/ X553 //3 30 3/8- x 7/ 3/8- x 7/ 0.75 X //3 0 3/8- x 7/ /-0 x 9/ 33X5 //3 30 M0 X 30 M0 X 30 33X53 //3 30 3/8- x 3/ 3/8- x 3/ 5X573 //3 30 3/8- x 7/ 3/8- x 7/.5 5X583 //3 30 3/8- x 7/ /-0 X 7/.5 5X0 //3 0 /-3 x 7/ /-3 x 7/ X //3 80 3/8- x 3/8- x = Block is also available with hinge cover attached - include at end of part number when ordering (not available on Adder blocks) - See page 55 for available covers See pages 5-5 for dimensional information Phone: 800.89.0 - Fax: 888.73.773 - Web: www.clrwtr.com - Email: info@clrwtr.com
Miscellaneous Power Splicer Blocks 00 Volts AC/DC Up to 000 Volts AC/DC ( ) +, High Conductive Aluminum, Tin Plated Rated for Copper and Aluminum Wire Stud, Brass, Tin Plated Quick Connect, Brass, Tin Plated 0-3 Screw, Brass, Nickel Plated Amp Rating Based on NEC Table 30- Using 75 o C Copper Wire UL Recognized File No. XCFR.E80 CSA Certified File No. LR97 30 305 Replace X with # of poles Poles (X) Amps MATERI Insulator Conn. Load Connection X00 //3/ 5 # - # AWG 0-3 Screw X0 //3/ 5 # - # AWG 0-3 Tapped Hole X0 //3/ 5 # - # AWG.5 x.03 QC X05 //3/ 5 # - # AWG #0-3 Hole & () QC X30 //3/ 5 # - # AWG # - # AWG & () QC X //3 75 /0 - # AWG M Hole X553 //3 75 /0 - # AWG /-0 Tapped Hole See page 55 for available covers See pages 5-5 for dimensional information Phone: 800.89.0 - Fax: 888.73.773 - Web: www.clrwtr.com - Email: info@clrwtr.com
00 Volts AC/DC Up to 000 Volts AC/DC ( ) +, High Conductive Aluminum, Tin Plated, Rated for Copper and Aluminum Wire Stud, Brass, Tin Plated, Metric (M) Studs, Steel - intended for wires terminated with crimp lugs Amp Rating Based on NEC Table 30- Using 75 o C Copper Wire UL Recognized File No. XCFR.E80 CSA Certified File No. LR97 (does not apply to 33X559, 33X558, and 3X559) Power Splicer/Stud Blocks 33559 53599 ** rated for #- AWG are multiple wire rated: () #0 Str, ( to ) # Str, and ( to ) # Str. *** rated for #- AWG are multiple wire rated: () #8 Str, () #0 Str, () # Str, and () # Str. Replace X with # of poles (0 = Adder) Hinge Cover Poles (X) Amps MATERI Insulator Conn. X03 //3/ 5 # - # AWG 0-3 X.0 Stud 3X57 0///3 75 /0 - # AWG /-0 x / 3X7 0///3 75 /0 - # AWG M x 3 X57 //3 75 /0 - # AWG /-0 x / 3X590 //3 75 /0 - # AWG /-0 x 3/8 3X559 //3 30 350 kcmil - # AWG 3/8- x /8 Stud 33X559 //3 30 350 kcmil - # AWG 3/8- x / 33X558 //3 30 350 kcmil - # AWG M0 x 30 0.75 X59 //3 380 500 kcmil - # AWG /-0 x / X575 //3 380 500 kcmil - # AWG 3/8 - x 5/ 5X59 //3 55 000 kcmil - 500 kcmil 3/8 - x 3/.00 5X599 //3 70 500 kcmil - # AWG 3/8 - x 5/. 5X0 //3 70 500 kcmil - # AWG /-3 x 5/ = Block is also available with hinge cover attached - include at end of part number when ordering (not available on Adder blocks) - See page 55 for available covers See pages 5-5 for dimensional information Phone: 800.89.0 - Fax: 888.73.773 - Web: www.clrwtr.com - Email: info@clrwtr.com
Power Stud to Distribution Blocks 00 Volts AC/DC Up to 000 Volts AC/DC ( ) +, High Conductive Aluminum, Tin Plated, Rated for Copper and Aluminum Wire Stud, Brass, Tin Plated, Metric (M) Studs, Steel - intended for wires terminated with crimp lugs Amp Rating Based on NEC Table 30- Using 75 o C Copper Wire UL Recognized File No. XCFR.E80 CSA Certified File No. LR97 33370 33373 ** rated for #- AWG are multiple wire rated: () #0 Str, ( to ) # Str, and ( to ) # Str. *** rated for #- AWG are multiple wire rated: () #8 Str, () #0 Str, () # Str, and () # Str. MATERI Replace X with # of poles Hinge Cover Poles (X) Amps Insulator Conn. Threaded Stud Size 33X7 //3 50 3/8- x 3/ # - # AWG** 33X73 //3 50 M0 x 30 # - # AWG** 33X80 //3 50 3/8- x 3/ # - # AWG*** 8 33X8 //3 50 M0 x 30 # - # AWG*** 8 33X70 //3 50 3/8- x 3/ /0 - # AWG*** 33X7 //3 50 M0 x 30 /0 - # AWG*** = Block is also available with hinge cover attached - include at end of part number when ordering - See page 55 for available covers See pages 5-5 for dimensional information Phone: 800.89.0 - Fax: 888.73.773 - Web: www.clrwtr.com - Email: info@clrwtr.com
Power Terminal Block Dimensions 3 SERIES.89 [.5].00 [5.5].8 [.3].55 [.8].5 [57.] SLOT.9 X. THRU [.3 X 5.5] TYP..8 [0.7] TYP. 3.00 [7.].3 [.3]. [.5].85 [.] Adder Pole.0 [5] Pole 3 Pole 3 SERIES.00 [5.5].8 [.3].55 [.8].5 [57.] (MTG. SLOTS) 3.00 [7.].8 [0.7] TYP..3 [.3] SLOT.9 X. THRU [.3 X 5.5] TYP..85 [.].0 [5]. [.5] (W/O COVER).57 [5.] (WITH COVER) Pole Pole 3 Pole 33 SERIES.9 [9.7].3[7.9] 3. [9.9] 5.3 [3.] SLOT. X.7 THRU CB. X.9 X.9 DP TYP..00 [0.] 3.38 [85.7].97[.] TYP..70 [3.] TYP. 3.0 [8.] 3.33 [8.].39 [9.8].89 [.5] Pole Pole 3 Pole Phone: 800.89.0 - Fax: 888.73.773 - Web: www.clrwtr.com - Email: info@clrwtr.com
Power Terminal Block Dimensions 33 SERIES.9 [9.7].3[7.9] 3. [9.9] 5.3 [3.] SLOT. X.7 THRU CB. X.9 X.9 DP TYP..00 [0.] 3.38 [85.7] (MTG. SLOTS).39[9.8].89 [.5].97 [.] TYP..70 [3.] TYP. 3.33 [8.] (W/O COVER) 3.0 [8.] (MTG SLOTS) 3.9 [88.] (WITH COVER) Pole Pole 3 Pole 0 SERIES SERIES.05 (5.) DIA. HOLE. (0.) DIA. CLEARENCE TYP..8 X.375 [5.5 X 9.5] SLOT.3 [8.].9 [9.].75 [9.8].3 [7.9] MARATHON L L MARATHON 3.38 [85.8] 3.5 [89.3].3 [0.8] MARATHON.5 [3.8].00 [.0] L MARATHON L MARATHON.3 [7.5].77 [.] 5.38 [3.] L3 MARATHON MARATHON.00 [5.].0.90 [.0] [73.7].5 X.375 [.7 X 9.5] SLOT.5 [.3]. [.]. [5.7].5 [57.].5 [.3].88 [73.0].05 [.38].0 [5.].0 [53.].89 [.].78 [5.].38 [9.] Pole 3 Pole Pole Pole 3 Pole. [.0].3 [5.9] SERIES.7 [7.7].7 [.7].0 [5.] DIA. THRU.07 [5.5].93 [9.].9 [58.] Pole.7 [3.3] Pole 3 Pole.38 [9.7]. [.].9 [8.8] TYP. AT BOSS.5 [3.] L POCKETS.8 [.5].3 [8.].70 [7.7].53 [38.8].83..0 [.0] [37.] [53.3] REF. REF. REF..9 [.9].7 [.9].75 [9.8] REF..55 [.] Phone: 800.89.0 - Fax: 888.73.773 - Web: www.clrwtr.com - Email: info@clrwtr.com
Power Terminal Block Dimensions 3 SERIES.9 [9.3] 3.7 [88.].03 (5.) DIA. HOLE.0 (0.3) C BORE TYP. 5.00 [7.0].00 [0.].53 [38.9].7 [9.7].53 [38.9].53 [38.9] 3.38 [85.7].3 [7.9].97 [.].05 [.]. [.] Pole. [5.5] Pole 3 Pole.0 [0.].00 [5.] SERIES.9 [58.].7 [05.9].05 [53.].0/[5.] DIA. THRU./[0.3] C'BORE x.8/[.] DP..75 [0.].3 [0.8].88 [7.8].50 [38.].88 [7.8].88 [7.8].3 [7.9]. [9.0].05 [.38]. [8.3].90 [73.7] Pole Pole 3 Pole.5 [3.] 5 SERIES 3.7 [80.] 5.85 [8.7].5/(.73) DIA. HOLE.500/(.7) C BORE X. [5.3] DP 8.5 [.9].75 [0.7] 5.50 [39.7].9 [8.].30 [58.].9 [8.].9 [8.].58 [0.].05 [.] Pole Pole 3 Pole.50 [.7].0 [7.9] 3. [79.] Phone: 800.89.0 - Fax: 888.73.773 - Web: www.clrwtr.com - Email: info@clrwtr.com
Power Block Covers 0///3//5 Series (Figures & ) Material UL Recognized, QMFZ, 5 o C,.0 Clear Protective Two Thread Cutting Screws Furnished Per Cover Covers are Slotted for Easy Installation 3/33 Series (Figure 3) Snap on, Hinged Cover, Black Thermoplastic UL Recognized, QMFZ, 5 o C B A Dimensions (in): FIGURE A B Figure # CC0.75.5 CC03.00.5 CC 0.77.0 CC..0 CC3.05.0 CC.8.0 CC.0.75 CC.87.75 CC3.8.75 CC3.78 3.38 CC3 3.3 3.38 CC33.8 3.38 CC..00 CC.00.00 CC3 5.87.00 CC5.87.50 CC5 5.5.50 CC53 8.8.50 3 3 - - 3 33 33 33 - - 3 333 B FIGURE A FIGURE 3 (Hinged Cover) Phone: 800.89.0 - Fax: 888.73.773 - Web: www.clrwtr.com - Email: info@clrwtr.com
SA 980705 - Grounding Lugs, High Conductive Aluminum, Tin Plated Screw head is green ink UL Recognized File No. ZMVV.E35 CSA Certified File No. 350-5 (Part #) GL0 (980705) Torque lb in # - #3 50 # - # 5 #8 0 #0 - # 35 GL0:.3 [5.9] C 5/- SET SCREW M Ø.3 [7.9].59 [5.].5 [9.].90 [.9] Ø. [.75].5 [.]. [.0].5 [.3].0 [35.].50 [.7] GL0: 3/ HEX SOCKET Ø.0 [0.3] (Part #) GL0 (9780) Torque lb in /0 - # 0 #8 0 #0 - # 35 Ø. [.].3 [33.3]. [.].3 [8.] 9780 M C SA.75 [9.].00 [5.].5 [.] /0-.3 [7.7].3 [.3]. [5.5] GL35: 5/ HEX SOCKET Ø.53 [3.9] (Part #) Torque lb in GL35 (989830) 350 kcmil - # 375.5 [.3] Ø.7 [8.3].9 [.9].3 [8.].50 [.7].5 [3.7] M CSA 989830 350MCM-.5 [3.8].5 [.].5 [.3].5 [57.].3 [8.] Phone: 800.89.0 - Fax: 888.73.773 - Web: www.clrwtr.com - Email: info@clrwtr.com