Features: Small size, minimal footprint/low profile A Output Current (all voltages) High Efficiency: up to 95% High reliability RoHS Compliant Cost efficient open frame design Pre-bias monotonic start-up Over-current and Over-temperature protection Output Input Efficiency PARD (mvp-p) Regulation Max Vin Nom. Range (V) Iin Max Full Load Vout (V) Iout (A) (V) (A) Typ. Max. Line Load Typ. 1 5 50 +/-0.1% +/-0.5% 5 3 5.0 % 1. 5 50 +/-0.1% +/-0.5% 5 3 5.75 % 1.5 0 50 +/-0.1% +/-0.5% 5 3 5 5.75 9% 1. 0 50 +/-0.1% +/-0.5% 5 3 5.75 91% 0 50 +/-0.1% +/-0.5% 5 3 5 7. 9%.5 0 50 +/-0.1% +/-0.5% 5 3 5 9.1 93% 3.3 0 50 +/-0.1% +/-0.5% 5.5-5.5 7. 95% Technical enquiries email: sales@murata-ps.com, tel: +50 339 3000 1 NCF0_00000_B01_1/0/0
Input Characteristics Notes & Conditions Min Typ. Max Units Input Voltage Operating Range 3.0 5 5.5 Vdc Input Reflected Ripple Current 0 ma p-p Inrush Current Transient 0. A s Input Filter Type (external) 0 μf Input Turn ON Threshold. V Input Turn OFF Threshold.7 V ON Control Open or 0 to +0.V OFF Control +.V to Vin (<3mA) Output Characteristics Notes & Conditions Min Typ. Max Units Vout Accuracy 50% load -1.5 +1.5 % Output Loading 0 A Output Ripple & Noise 30 mv @ 0Mhz Bandwidth. Maximum Capacitive Load Low ESR 000 μf Vout Trim Range - + % Total Accuracy Over line/load temperature <3% Current Limit 13 1 0 A Output Line Regulation -0.1 +0.1 % Output Load Regulation +0.5-0.5 % Turn-on Overshoot 1 % SC Protection Technique Pre-bias Start-up at output Hiccup with auto recovery Unit starts monotonically with prebias Dynamic Characteristics Notes & Conditions Min Typ. Max Units Load Transient 50% step,.5a/μs 0 mv Settling Time 0 μs Frequency 300 khz Start-Up Time Vin to Vout and On/Off to Vout Vout rise to monotonic <0 ms General Specifications Notes & Conditions Min Typ. Max Units MTBF Calculated (MIL-HDBK-17F) 1.5 x Hrs Demonstrated @ 0% Confidence 1 x Hrs Level Thermal Protection Hotspot 1 10 C Operating Temperature Without derating -0 0 C Dimensions Lx0.3 Wx0.5 H (50.x.x1.7mm) Pin Dimensions 0.03 (0.7mm) Pin Material Matte Sn Finish on component Leads Weight 0.3 ounces (.5g) Flammability Rating UL9V-0 Standards Compliance CSA C., No.0950/UL 0950, Third Edition (000), File UL E15113 NCF0_00000_A03_05Jun07
Thermal Considerations The power module operates in a variety of thermal environments; however, sufficient cooling should be provided to help ensure reliable operation of the unit. Heat is removed by conduction, convection, and radiation to the surrounding environment. The thermal data presented is based on measurements taken in a set-up as shown in fig 1. when the airflow is parallel to the long axis of the module. The de-rating applies accordingly. The temperature at either location should not exceed 1 C. The output power of the module should not exceed the rated power for the module (VO, set x IO, max). Figure 1: Thermal Measurement Setup Convection Requirements for Cooling To predict the approximate cooling needed for the module, refer to the Power Derating Curve in Figure to Figure. These derating curve are approximations of the ambient temperature and airflow required to keep the power module temperature below it's maximum rating. Once the module is assembled in the actual system, the module's temperature should be verified. Proper cooling can be verified by measuring the power module's temperature at Q1-pin and Q-pin as shown in Figure 1. 3 NCF0_00000_A03_05Jun07
TYPICAL DERATING CURVES NCF000B (5Vin) Derating Curve 1 Output Current (A) 0 LFM 0 LFM 00 LFM 0 0 0 30 0 50 0 70 0 90 Ambient Temperature (C) Figure. Typical Power Derating vs Output Current for 5Vi and 1.0Vo. NCF0010B (5Vin) Derating Curves 1 Output Current (A) 0 LFM 0 LFM 00 LFM 0 0 0 30 0 50 9 70 0 90 Ambient Temperature (C) Figure 3. Typical Power Derating vs Output Current for 5Vi and 1.Vo. NCF0_00000_A03_05Jun07
NCF00150B (5Vin) Derating Curve Output Current (A) 1 0 LFM 0 LFM 00 LFM 0 0 0 30 0 50 70 0 90 Ambient Temperature (C) Figure. Typical Power Derating vs Output Current for 5Vi and 1.5Vo. NCF0010B (5Vin) Derating Curve 1 Output Current (A) 0 LFM 0 LFM 00 LFM 0 0 0 30 0 50 0 70 0 90 Ambient Temperature (C) Figure 5. Typical Power Derating vs Output Current for 5Vi and 1.Vo. 5 NCF0_00000_A03_05Jun07
NCF0000B (5Vin) Derating Curve Output Current (A) 1 0 LFM 0 LFM 00 LFM 0 0 0 30 0 50 70 0 90 Ambient Temperature (C) Figure. Typical Power Derating vs Output Current for 5Vi and.0vo. NCF0050B (5Vin) Derating Curve 1 Output Current (A) 0 LFM 0 LFM 00 LFM 0 0 0 30 0 50 70 0 90 Ambient Temperature (C) Figure 7. Typical Power Derating vs Output Current for 5Vi and.5vo. NCF0_00000_A03_05Jun07
NCF00330B0 (5Vin) Derating Curve Output Current (A) 1 0 LFM 0 LFM 00 LFM 0 0 0 30 0 50 0 70 0 90 Ambient Temperature (C) Figure. Typical Power Derating vs Output Current for 5Vi and 3.3Vo. TYPICAL EFFICIENCY CURVES NCF00330B0 (5C) Eff vs Output Load Efficiency (%) 9.00% 9.00% 9.00% 9.00% 90.00%.00%.00%.00%.00% 0.00% 1 3 5 7 9 Output Load (A) Vin=.5V Vin=5.0V Vin=5.5V Figure 9. Efficiency Curves for Vout=3.3V (5C) 7 NCF0_00000_A03_05Jun07
NCF0050B0 (5C) Eff vs Output Load Efficiency (%) 0.00% 95.00% 90.00% 5.00% 0.00% 75.00% Vin=3.0V Vin=5.0V Vin=5.5V 70.00% 1 3 5 7 9 Output Load (A) Figure. Efficiency Curves for Vout=.5V (5C) NCF0000B0 (5C) Eff vs Output Load Efficiency (%) 0.00% 95.00% 90.00% 5.00% 0.00% 75.00% Vin=3.0V Vin=5.0V Vin=5.5V 70.00% 1 3 5 7 9 Output Load (A) Figure 11. Efficiency Curves for Vout=.0V (5C) NCF0_00000_A03_05Jun07
NCF0010B0 (5C) Eff vs Output Load Efficiency (%) 0.00% 90.00% 0.00% 70.00% 0.00% 50.00% 0.00% 30.00% 0.00%.00% 0.00% 0.5 1.5.5 3.5.5 5.5.5 7.5.5 9.5 Vin=3.0V Vin=5.0V Vin=5.5V Output Load (A) Figure 1. Efficiency Curves for Vout=1.V (5C) NCF00150B0 (5C) Eff vs Output Load Efficiency (%) 0.00% 90.00% 0.00% 70.00% 0.00% 50.00% 0.00% 30.00% 0.00%.00% 0.00% 1 3 5 7 9 Output Load (A) Vin=3.0V Vin=5.0V Vin=5.5V Figure 13. Efficiency Curves for Vout=1.5V (5C) 9 NCF0_00000_A03_05Jun07
NCF0010B0 (5C) Eff vs Output Load Efficiency (%) 0.00% 90.00% 0.00% 70.00% 0.00% 50.00% 0.00% 30.00% 0.00%.00% 0.00% 1 3 5 7 9 Output Load (A) Vin=3.0V Vin=5.0V Vin=5.5V Figure 1. Efficiency Curves for Vout=1.V (5C) NCF000B0 (5C) Eff vs Output Load Efficiency (%) 0.00% 90.00% 0.00% 70.00% 0.00% 50.00% 0.00% 30.00% 0.00%.00% 0.00% 1 3 5 7 9 Output Load (A) Vin=3.0V Vin=5.0V Vin=5.5V Figure 15. Efficiency Curves for Vout=1.0V (5C) NCF0_00000_A03_05Jun07
Typical Start Up Ch 1. Vin Ch. Vout. Typical Start Up with pre-bias Ch1 : Enable Ch : Vout 11 NCF0_00000_A03_05Jun07
Typical Output Noise and Ripple Output Voltage Set point adjustment. The following relationship establish the calculation of external resistors: Trim-Up For trim_up an external resistor is connected between the TRIM and Ground Pin. Rtrim_Up Vr R1 V Rt Where, Rt = internal buffer resistor. For calculation choose value as per table below: Vo, set (Volts) Rt (KΩ) 3.3 59.5 7.7.0 0 1. 0 1.5 0 1. 59 1.0 30.1 1 NCF0_00000_A03_05Jun07
R1 = 30.1 KΩ Murata Power Solutions ΔV = Change in adjustment voltage required ( example % of Volts = 0.1). Vr = 0. Trim_Down For trim down an external resistor is to be connected between TRIM and Vout pins of the module. The value of Rtrim_Down is calculated from the following relationship. Rtrim_Down Vout Vr V 1 R1 Rt The values of Vr, R1 and Rt are as defined above. ΔV is the adjustment trim required. Examples: Vout = 1.5V Trim_Up required % to 1.V Rtrim_Up 300 0. 0.1 0000 Rtrim_Up 0. k Vout = 1.5V Trim_Down required % to 1.3V Rtrim_Down 1.5 0. 0.1 1 300 0000 Rtrim_Down 5.3 k Remote Sense: All Murata Power Solutions SIP power modules offer an option for remote sense. The remote sense compensates for any distribution drops to accurately control voltage at the point of load. The voltage between the sense pin to Vout pin should not exceed 0.5V. Safety Considerations The NCF series of converters are certified to IEC/EN/CSA/UL 0950. If this product is built into information technology equipment, the installation must comply with the above standard. An external input fuse of less than 50 Amps (5A to 30A recommended), must be used to meet the above requirements. The output of the converter [Vo(+)/Vo(-)] is considered to remain within SELV limits when the input to the converter meets SELV or TNV- requirements. The converters and materials meet UL 9V-0 flammability ratings. 13 NCF0_00000_B01_1/0/0
SMT Lead free Reflow profile 1. Ramp up rate during preheat : 1.33 /Sec ( From 30 to 150 ). Soaking temperature : 0.9 /Sec ( From 150 to 10 ) 3. Ramp up rate during reflow : 0. /Sec ( From 0 to 50 ). Peak temperature : 50, above 0 0 to 70 Seconds 5. Ramp up rate during cooling : -1.5 /Sec ( From 0 to 150 ) Mechanical Information SIZE SIP 0.37(.3) 0.139(3.53) 0.(.5) 0.9(7.).00(50.) 0.50(1.7) 1 3 5 7 9 11 0.0(.) 0.05(0.) 1.00(5.) LAYOUT PATTE RN TOP VIEW All Dimmension In Inches(mm) Tolerance :.XX= ± 0.0.XXX= ± 0.0 0.05(1.3) 0.3(5.) 0.(7.) 0.05(0.) 0.33(.) 1.1mm PLATED THROUGH HOLE 1.mm PAD SIZE PIN CONNECTION Pin FUNCTION 1 3 5 7 9 11 +Output +Output +Sense +Output Common Common +V Input +V Input No Pin Trim On/Off Control 1 NCF0_00000_A03_05Jun07
Ordering Information Part Number Vin Vout Iout Enable Logic Pin Length NCF000B0C 3.0V - 5.5V 1.0V A Negative 0.139" NCF0010B0C 3.0V - 5.5V 1.V A Negative 0.139" NCF00150B0C 3.0V - 5.5V 1.5V A Negative 0.139" NCF0010B0C 3.0V - 5.5V 1.V A Negative 0.139" NCF0000B0C 3.0V - 5.5V.0V A Negative 0.139" NCF0050B0C 3.0V - 5.5V.5V A Negative 0.139" NCF00330B0C.5V - 5.5V 3.3V A Negative 0.139" NCF001B0C 3.0V - 5.5V 1.0V A Positive 0.139" NCF0011B0C 3.0V - 5.5V 1.V A Positive 0.139" NCF00151B0C 3.0V - 5.5V 1.5V A Positive 0.139" NCF0011B0C 3.0V - 5.5V 1.V A Positive 0.139" NCF0001B0C 3.0V - 5.5V.0V A Positive 0.139" NCF0051B0C 3.0V - 5.5V.5V A Positive 0.139" NCF00331B0C.5V - 5.5V 3.3V A Positive 0.139" Label Information N C F 0 1 0 x x x 0 B 0 X C C = RoHS Compliant Iout Place Holder Vout Range F=Fixed A=Adjustable Vin (value or range) C= 3.3V - 5.0V E=.3V - 1V F=.0V -1V Vout 0 = Standard. (No PGood option) P = Power Good Option Pin Length Option B=0.139 S=SMT Enable Logic, 0 for ve, 1 for +ve X = Factory control character (not required when ordering) Non - Isolated Family RoHS Compliant The NCF0 series of converters is in compliance with the European Union Directive 00/95/EC (RoHS) with repsect to the following sustances: lead (Pb), mercury (Hg), cadmium (Cd), hexavalent chromium, polybrominated biphenyls (PBB) or polybrominated diphenyl ethers (PBDE). 15 NCF0_00000_B01_1/0/0