CPC12N Single-Pole, Normally Open 4-Lead SOP OptoMOS Relay Parameter Rating Units Blocking Voltage 3 V P Load Current 1.2 A DC On-Resistance (max).2 Features 1V rms Input/Output Isolation Small 4-Lead SOP Package Low Drive Power Requirements (TTL/CMOS Compatible) No Moving Parts High Reliability Arc-Free With No Snubbing Circuits No EMI/RFI Generation Machine Insertable, Wave Solderable Tape & Reel Version Available Applications Sensor Circuitry Instrumentation Multiplexers Data Acquisition Electronic Switching I/O Subsystems Meters (Watt-Hour, Water, Gas) Medical Equipment Patient/Equipment Isolation Aerospace Industrial Controls Description The CPC12N is a 3V, single-pole, normally open (1-Form-A) Solid State Relay. The ultra-low on-resistance,.2, of this relay allows for high-current operation. IXYS Integrated Circuits Division's patented OptoMOS architecture makes available the optically coupled technology necessary to activate the output's efficient MOSFET switches while providing 1V rms input to output isolation. Control of the isolated output is accomplished by means of the highly effective GaAlAs infrared LED at the input. Approvals UL Recognized Component: File E7627 CSA Certified Component: Certificate 117739 EN/IEC 69-1 Certified Component: TUV Certificate B 9 7 4941 4 Ordering Information Part # Description CPC12N 4-Lead SOP (1/tube) CPC12NTR 4-Lead SOP (2/reel) Pin Configuration 1 + Control 4 Load 2 3 Control Load Switching Characteristics of Normally Open Devices Form-A 9% I LOAD 1% t on t off Pb e3 DS-CPC12N-R3 www.ixysic.com 1
CPC12N Absolute Maximum Ratings @ 2ºC Parameter Ratings Units Blocking Voltage 3 V P Input Power Dissipation 1 7 mw Input Control Current ma Peak (1ms) 1 A Reverse Input Voltage V Total Power Dissipation 2 4 mw Isolation voltage, Input to Output 1 V rms Operational Temperature -4 to +8 C Storage Temperature -4 to +12 C 1 Derate linearly 1.33 mw / ºC 2 Derate linearly 3.33 mw / ºC Absolute Maximum Ratings are stress ratings. Stresses in excess of these ratings can cause permanent damage to the device. Functional operation of the device at conditions beyond those indicated in the operational sections of this data sheet is not implied. Electrical Characteristics @ 2ºC Parameter Conditions Symbol Min Typ Max Units Output Characteristics Load Current Continuous 1 =2mA I L - - 1.2 A DC Peak t < 1ms I LPK - - 3 A On-Resistance 2 I L =1A R ON -.116.2 Off-State Leakage Current V L =3V P I LEAK - - 1 A Switching Speeds Turn-On t =ma, V L =1V on -.48 3 Turn-Off t off -.6 3 ms Output Capacitance V L =1V, f=1mhz C OUT - 7 - pf Input Characteristics Input Control Current to Activate I L =1A -.13 2 ma Input Control Current to Deactivate -.1 - - ma Input Voltage Drop =ma V F.9 1.2 1.4 V Reverse Input Current V R =V I R - - 1 µa Input/Output Characteristics Capacitance, Input to Output - C I/O - 3 - pf 1 Load current derates linearly from 1.2A @ 2 o C to.8a @8 o C. 2 Measurement taken within 1 second of on-time. ESD Rating ESD Rating (Human Body Model) 1 Volts R3 2 www.ixysic.com
CPC12N PERFORMANCE DATA* 2 Typical Turn-On Time Distribution (N=, =ma, I L =ma, T A 3 Typical Turn-Off Time Distribution (N=, =ma, I L =ma, T A 2 Typical On-Resistance Distribution (N=, =2mA, I L =1A, T A 2 1 1 2 2 1 1 1 1.3.4.4...6 Turn-On Time (ms).47..63.71.79 Turn-Off Time (ms).113.114.11.116.117.118 On-Resistance ( ) 2 Typical for Switch Operation (N=, I L =1mA, T A 2 Typical Blocking Voltage Distribution (N=, T A 3 Typical LED Forward Voltage Drop (N=, =ma, T A 2 1 1 2 1 1 3 2 2 1 1.93.11.19.117.12.133 37.8 38.2 38.6 39. 39.4 Blocking Voltage (V P ) 1.2 1.26 1.27 1.28 1.29 LED Forward Voltage (V) LED Forward Voltage (V) 1.6 1. 1.4 1.3 Typical LED Forward Voltage Drop =ma =2mA =1mA 1.2 1.1 =ma =2mA 1. -4-2 2 4 6 8 1 Turn On Time (ms) 2. 2. 1. 1.. Typical Turn-On Time vs. LED Forward Current =1mA) 1 2 3 4 Turn-Off Time ( s) 7 68 66 64 62 6 Typical Turn-Off Time vs. LED Forward Current =1mA) 1 2 3 4.2.18.16.14.12.1 Typical for Switch Operation =1A).8-4 -2 2 4 6 8 1 Turn-On Time (ms) 3. 3. 2. 2. 1. 1.. Typical Turn-On Time =1mA) =2mA =ma -4-2 2 4 6 8 1 Turn-Off Time (ms) Typical Turn-Off Time =1mA) 1.2 1.1 1..9.8 =2mA.7.6. =ma.4-4 -2 2 4 6 8 1 *The Performance data shown in the graphs above is typical of device performance. For guaranteed parameters not indicated in the written specifications, please contact our application department. R3 www.ixysic.com 3
CPC12N PERFORMANCE DATA* 1. Typical Load Voltage vs. Load Current ( =2mA, T A Typical On-Resistance ( =2mA, I L =.A).4 1. Maximum Load Current ( =2mA) Load Current (A) 1... -. -1. On-Resistance ( ).3.3.2.2.1 Load Current (A DC ) 1.2 1..7..2-1. -.2 -.1 -.1 -....1.1.2 Load Voltage (V).1-4 -2 2 4 6 8 1. -4-2 2 4 6 8 1 Blocking Voltage (V P ) Typical Blocking Voltage =1 A) 4. 4. 39. 39. 38. 38. 37. 37. 36. -4-2 2 4 6 8 1 Leakage Current (na) Typical Leakage Current Measured Across Pins 3&4 ( =ma, V L =3V) 1 8 6 4 2-4 -2 2 4 6 8 1 Current (A) Energy Rating Curve 3. 3. 2. 2. 1. 1... 1 s 1 s 1ms 1ms 1ms 1s 1s 1s Time *The Performance data shown in the graphs above is typical of device performance. For guaranteed parameters not indicated in the written specifications, please contact our application department. R3 4 www.ixysic.com
CPC12N Manufacturing Information Moisture Sensitivity All plastic encapsulated semiconductor packages are susceptible to moisture ingression. IXYS Integrated Circuits Division classified all of its plastic encapsulated devices for moisture sensitivity according to the latest version of the joint industry standard, IPC/JEDEC J-STD-2, in force at the time of product evaluation. We test all of our products to the maximum conditions set forth in the standard, and guarantee proper operation of our devices when handled according to the limitations and information in that standard as well as to any limitations set forth in the information or standards referenced below. Failure to adhere to the warnings or limitations as established by the listed specifications could result in reduced product performance, reduction of operable life, and/or reduction of overall reliability. This product carries a Moisture Sensitivity Level (MSL) rating as shown below, and should be handled according to the requirements of the latest version of the joint industry standard IPC/JEDEC J-STD-33. Device Moisture Sensitivity Level (MSL) Rating CPC12N MSL 3 ESD Sensitivity This product is ESD Sensitive, and should be handled according to the industry standard JESD-62. Reflow Profile This product has a maximum body temperature and time rating as shown below. All other guidelines of J-STD-2 must be observed. Device CPC12N Maximum Temperature x Time 26ºC for 3 seconds Board Wash IXYS Integrated Circuits Division recommends the use of no-clean flux formulations. However, board washing to remove flux residue is acceptable. Since IXYS Integrated Circuits Division employs the use of silicone coating as an optical waveguide in many of its optically isolated products, the use of a short drying bake could be necessary if a wash is used after solder reflow processes. Chlorine- or Fluorine-based solvents or fluxes should not be used. Cleaning methods that employ ultrasonic energy should not be used. Pb e3 R3 www.ixysic.com
CPC12N MECHANICAL DIMENSIONS CPC12N 4.89 ±.23 (.161 ±.8).2 ±.2 (.8 ±.1) Recommended PCB Land Pattern.6 (.217) 3.81 ±.76 (.1 ±.3) Pin 1 2.4 Typ (.1 Typ) 6.96 ±.12 (.24 ±.4) 1.2 ±.2 (.4 ±.1).432 ±.127 (.17 ±.) 1.3 (.12).6 (.22) 2.184 Max (.86 Max) Lead to package standoff:.637 ±.383 (.2 ±.1) 2.4 (.1).762 ±.12 (.3 ±.4).381 TYP. (.1 TYP.) Dimensions mm (inches) CPC12NTR Tape & Reel 33.2 Dia (13. Dia) Top Cover Tape Thickness.12 Max (.4 Max) B =4.7 (.18) W=12. (.472) K =2.7 (.16) K 1 =2.3 (.91) A =6. (.26) P=8. (.31) User Direction of Feed Embossed Carrier Dimensions mm (inches) Embossment NOTE: All dimensional tolerances per Standard EIA-481-2 except as noted For additional information please visit our website at: www.ixysic.com IXYS Integrated Circuits Division makes no representations or warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications and product descriptions at any time without notice. Neither circuit patent licenses nor indemnity are expressed or implied. Except as set forth in IXYS Integrated Circuits Division s Standard Terms and Conditions of Sale, IXYS Integrated Circuits Division assumes no liability whatsoever, and disclaims any express or implied warranty, relating to its products including, but not limited to, the implied warranty of merchantability, fitness for a particular purpose, or infringement of any intellectual property right. The products described in this document are not designed, intended, authorized or warranted for use as components in systems intended for surgical implant into the body, or in other applications intended to support or sustain life, or where malfunction of IXYS Integrated Circuits Division s product may result in direct physical harm, injury, or death to a person or severe property or environmental damage. IXYS Integrated Circuits Division reserves the right to discontinue or make changes to its products at any time without notice. 6 Specification: DS-CPC12N-R3 Copyright 212, IXYS Integrated Circuits Division OptoMOS is a registered trademark of IXYS Integrated Circuits Division All rights reserved. Printed in USA. 12/13/212