All-in-one Projector Adapter Plate I5300 series, I5500 series, and SP8602 series Model: SP-CEIL-ISTALL Maximum Load Capacity: 50 lbs/22 kg Read all instructions before you start installation and assembly. R This product is intended for use with UL Listed products and must be installed by a qualified professional installer. Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. IMPORTAT! Turn to the appropriate page for your ceiling installation. Applications: Projector Mount Installation to Wood oist Ceilings... page 3 Projector Mount Installation to Concrete Ceilings...page 4 Ceiling Plate Installation to Wood oist Ceilings...page 5 Ceiling Plate Installation to Concrete Ceilings... page 6 Extension Column Installation...page 7 Installation to Extension Column...page 8 Installation to Threaded Rod...page 9 I5500 Series I5300 Series and SP8602 1 of 12
efore you start check the parts list to ensure all of the parts shown are included. Parts List Description Qty. Part # A adapter plate 1 055-1941 projector mount assembly 1 055-1968 C M6 x 30 mm socket pin screw 4 520-1067 D 1/4" flat washer 4 540-9440 E.25 ID x.38 x.75 spacer 4 590-1120 F 4 mm security allen wrench 2 560-9646 G #10-32 x 3/8" serrated washer head socket pin screw 2 520-1151 H #10-32 x 1/4" socket pin screw 1 520-1196 I flat washer 2 540-1078 #14 x 2.5 phillips hex head wood screw 4 5S1-015-C03 concrete anchor 4 590-0097 L 2 mm security allen wrench 1 560-1097 M connection block, blk. 1 580-1065 ceiling plate 1 580-1042 O M5 x 10 mm socket pin screw 1 520-1164 P M5 x 10 mm phillips screw 1 520-9250 A M C D E F G H I L O P Q ote: Actual parts may appear slightly different than illustrated. 2 of 12
Projector Mount Installation to Wood oist Ceilings Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. Tighten wood screws so that projector mount assembly is firmly attached, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power. ever tighten in excess of 80 in. lb (9.M.). Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder is highly recommended. Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs. Installers are responsible to provide hardware for other types of mounting situations (not evaluated by UL). 1 Place projector mount assembly () on ceiling as a template and mark the center of the two mounting holes. Make sure that the mounting holes are in the center of the wood joist. Drill two 5/32" (4 mm) dia. holes to a minimum depth of 2.5" (64 mm). Attach projector mount assembly () with two #14 x 2.5" (6 mm x 65 mm) wood screws () and two flat washers (I) as shown in figure 1.1 or figure 1.2 depending on joist orientation. ote: Mounting slots on projector mount assembly allow for 30 (±15 ) of swivel adjustment before fully securing wood screws. Tighten wood screws () using 3/8" (10 mm) socket wrench, phillips screwdriver or 10mm open end wrench until projector mount assembly () is firmly attached. Skip to step 6. WOOD OIST WOOD OIST ARROW O TOP OF PROECTOR MOUT ASSEMLY IDICATES FROT OF MOUT I I fig. 1.1 fig. 1.2 3 of 12
Projector Mount Installation to Concrete Ceilings Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor. Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. 2 Place projector mount assembly () on ceiling as a template and mark the center of the two mounting holes. Drill two 1/4" (6 mm) dia. holes to a minimum depth of 2.5" (64 mm). Attach projector mount assembly () using two concrete anchors (), two flat washers (I), and two #14 x 2.5" wood screws () as shown. ote: Mounting slots on projector mount assembly allow for 30 (±15 ) of swivel adjustment before fully securing wood screw. Tighten wood screws () using 3/8" (10 mm) socket wrench, phillips screwdriver or 10 mm open end wrench until projector mount assembly () is firmly attached. Skip to step 6. COCRETE CEILIG ARROW O TOP OF PROECTOR MOUT ASSEMLY IDICATES FROT OF MOUT CUTAWAY VIEW Tighten wood screws firmly, but do not overtighten. Overtightening can damage screws, greatly reducing their holding power. ever tighten in excess of 80 in. lb (9.M.). ICORRECT plaster/ dry wall Always attach concrete anchors directly to loadbearing concrete. ever attach concrete anchors to concrete covered with plaster, drywall, or other finishing material. If mounting to concrete surfaces covered with a finishing surface is unavoidable (not evaluated by UL), the finishing surface must be counter bored as shown below. e sure concrete anchors do not pull away from concrete when tightening screws. If plaster/drywall is thicker than 5/8", custom fasteners must be supplied by installer (not evaluated by UL). concrete CORRECT plaster/ dry wall concrete 1 2 3 I Drill holes and insert anchors (). concrete surface Place plate () over anchors () and secure with screws (). Tighten all fasteners. 4 of 12
Ceiling Plate Installation to Wood oist Ceilings 1 Drill two 5/32" (4 mm) dia. holes to a minimum depth of 2.5" (64 mm). Attach ceiling plate () with two #14 x 2.5" wood screws () as shown using 3/8" (10 mm) socket wrench. Installer must verify that the supporting surface will safely support the combined weight of mount and projector. Tighten wood screws so that ceiling plate is firmly attached, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power. ever tighten in excess of 80 in lb (9.M.). Make sure that mounting screws are anchored into the center of the studs. The use of an "edge to edge" stud finder is highly recommended. IMPORTAT: e sure to drill holes into the joist CETER! WOOD OIST CEILIG 5 of 12
Ceiling Plate Installation to Concrete Ceilings Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor. Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. 2 Place ceiling plate () on ceiling as a template and mark the center of the two mounting holes. Drill two 1/4" (6 mm) dia. holes to a minimum depth of 2.5" (64 mm). Attach ceiling plate () using two concrete anchors (), two flat washers (I), and two #14 x 2.5" wood screws () as shown. ote: Mounting slots on projector mount assembly allow for 30 (±15 ) of swivel adjustment before fully securing wood screw. Tighten wood screws () using 3/8" (10 mm) socket wrench, phillips screwdriver or 10 mm open end wrench until ceiling plate () is firmly attached. Skip to step 6. COCRETE CEILIG Tighten wood screws firmly, but do not overtighten. Overtightening can damage screws, greatly reducing their holding power. ever tighten in excess of 80 in. lb (9.M.). CUTAWAY VIEW Always attach concrete anchors directly to loadbearing concrete. ever attach concrete anchors to concrete covered with plaster, drywall, or other finishing material. If mounting to concrete surfaces covered with a finishing surface is unavoidable (not evaluated by UL), the finishing surface must be counter bored as shown below. e sure concrete anchors do not pull away from concrete when tightening screws. If plaster/drywall is thicker than 5/8", custom fasteners must be supplied by installer (not evaluated by UL).. ICORRECT plaster/ dry wall concrete CORRECT plaster/ dry wall concrete 1 Drill holes and insert anchors (). 2 3 concrete surface Place plate () over anchors () and secure with screws (). Tighten all fasteners. 6 of 12
Extension Column Installation 3 Attach extension column (sold separately) to ceiling plate (). Align the notch with one of the four holes in the ceiling plate () and secure extension column with a M5 x 10 phillips screw (P) or a M5 x 10 mm socket pin screw (O) using security allen wrench (F). See detail 1. O or P 1 1/2" EXTESIO COLUM (SOLD SEPARATELY) (UL LISTED EXT OR AEC SERIES) DETAIL 1 SLOT 7 of 12
Installation to Extension Column 4 Screw projector mount assembly () onto extension column as shown in figure 4.1. Tighten swivel stop screw against extension column, flush mount tube or reducer using 4 mm security allen wrench (F) as shown in figure 4.2. OTE: Swivel stop screw is used to jam against threads of extension column, flush mount tube or reducer to prevent any excess movement of projector mount assembly (). Do not overtighten screw; overtightening screw will damage threads making it difficult to separate products. Skip to step 6. 1 1/2" EXTESIO COLUM (SOLD SEPARATELY) (UL LISTED EXT OR AEC SERIES) ARROW IDICATES FROT OF MOUT fig. 4.1 CM 455 (SOLD SEPARATELY) SWIVEL STOP SCREW fig. 4.2 8 of 12
Installation to Threaded Rod (Professional installation only, not evaluated by UL) 5 Thread two 1/4-20 hex thin nylon-insert locknuts (not included) on two 1/4-20 threaded rods (not included) to the desired height of projector mount assembly. Attach projector mount assembly () to the two 1/4-20 threaded rods using two 1/4-20 hex thin nylon-insert locknuts as shown in figure 5.1 or figure 5.2. 1/4-20 THREADED ROD (OT ICLUDED) 1/4-20 HEX THI YLO-ISERT LOCUT (OT ICLUDED) 1/4-20 THREADED ROD (OT ICLUDED) 1/4-20 HEX THI YLO-ISERT LOCUT (OT ICLUDED) ARROW IDI- CATES FROT OF MOUT ARROW IDI- CATES FROT OF MOUT 1/4-20 HEX THI YLO-ISERT LOCUT (OT ICLUDED) 1/4-20 HEX THI YLO-ISERT LOCUT (OT ICLUDED) fig. 5.1 fig. 5.2 9 of 12
OTE: The projector adapter plate and projector you are installing may differ in appearance from the samples illustrated below. 6 Align shoulder on connection block (M) opposite of front of projector. Attach adapter plate (A) to connection block (M) using two #10-32 X 3/8" serrated socket pin screws (G) as shown. M SHOULDER OTCH IDICATES FROT OF PROECTOR A G 7 Flip projector upside down. Using the holes indicated on the corresponding hole pattern diagram, attach adapter plate (A) to projector using four M6 X 30 mm socket pin screws (C) and four 1/4" washers (D) and four.25 ID X.38 X.75 spacers (E). OTE: Spacers go between adapter plate and projector. Failure to do so may void projector warranty if damage occurs. C D C D A E FROT OF PROECTOR A E FROT OF PROECTOR I5500 Series I5300 Series and SP8602 10 of 12
Always use an assistant or mechanical lifting equipment to safely lift and position the projector. 8 Slide connection block (M) with projector into projector mount assembly () as shown. Tighten captive screw to secure projector to projector mount assembly (). FROT OF MOUT M CAPTIVE SCREW I5500 Series ROUTE CORDS CAPTIVE SCREW M I5300 Series and SP8602 9 IMPORTAT: For security installations, insert one #10-32 X 1/4" socket pin screw (H) through projector mount assembly (A) and into connection block (M) as shown. CLIP CORDS ITO TEETH O AC OF THE PROECTOR A H FROT OF PROECTOR 11 of 12
Projector Alignment 10 To adjust yaw (swivel) for threaded rod mounting applications: Loosen locknuts for threaded rods (refer to step four) until projector mount can be rotated. Rotate mount to desired position and retighten locknuts. To adjust yaw (swivel) for extension column applications: Loosen screw on projector mount assembly (A) indicated below until projector mount can be rotated. Rotate mount to desired position and retighten screw. To adjust pitch (forward and backward tilt): Turn knob on back of mount as shown below. Pull knob out and turn by hand for easy adjustment or insert #2 phillips screwdriver in end of knob and turn. To adjust roll (side to side tilt): Turn knob on side of mount as shown below. Pull knob out and turn by hand for easy adjustment or insert #2 phillips screwdriver in end of knob and turn. SCREW FOR YAW (SWIVEL) STOP (REFER TO STEP 2, ISTALLATIO TO EXTESIO COLUMS, FIG. 2.3) O FOR ROLL ADUSTMET ARROW IDICATES FROT OF MOUT O FOR PITCH ADUSTMET AC OF MOUT 10-1 To prevent tampering with the pitch and roll adjustments: Tighten the two tamper resistant security screws on the projector mount assembly using 4 mm security allen wrench (L) to lock the pitch and roll adjustments as shown below. ote: Tighten screws firmly, but do not overtighten. Overtightening can damage the mount. CAUTIO Do not adjust pitch or roll while tamper resistant security screws are fully engaged. Loosen the two tamper resistant security screws one complete turn before adjusting the projector mount assembly or damage may occur. TO LOC ROLL TIGHTE TAMPER RESISTAT SECURITY SCREW TO LOC PITCH TIGHTE TAMPER RESISTAT SECURITY SCREW FROT VIEW SIDE VIEW 12 of 12