MR RESISTOR 110-230V~ DIMMER WITH BUIT-I RADIO RECEIVER AD DAI PUT FOR CTRO BAASTS AD AMPS. Push-button input for manual controls. Product code TVDMA868A01 20 slaves, 868.3Mhz TVDMA868A02 64 slaves, 868.3Mhz TVDMA916A01 20 slaves, 916Mhz TVDMA916A02 64 slaves, 916Mhz P1 P2 ed 1 ed 2 ed 3 ed 4 Remove J1 and J2 if an external DAI power supply is used! 230V~ I 230V~ DIP 5 4 3 2 1 J1 J2 DA1 DA2 DA1 DA2 DAI I DAI Push-button input for manual controls. It s possible to connect in parallel more than one push-button. T3 < 0,5 s = / > 0,5 s = DIMMER ꜛ ꜜ Mounting 165 mm 40 mm 47 mm Hole for fixing with screw (under the cover) Flat surface mounting TVDMAxxxA01-A02 DOC.: T559.03 DATE: 07/10/16
Wirings BROADCAST DIP1..5 = 1 2 3 4 5 SAVE 1 SAVE 2 230V~ DIP J1 J2 DA1 DA2 DAI T3 TVDMAxxxA01 20 slaves TVDMAxxxA02 64 slaves DAI GROUP (0..15) To test the led wiring: P1 / < 1s DIMMER ꜛ ꜜ > 1s GROUP DIP1 DIP2 DI DIP4 0 1 2 3 4 GROUP DIP1 DIP2 DI DIP4 8 9 10 11 12 DIP5 =... DAI GROUP DAI GROUP SAVE SAVE DAI POWER SUPPY UIT 5 6 7 13 14 15 1 2 3 4 5 230V~ DIP J1 J2 DA1 DA2 DA1 DA2 T3 DAI I DAI Remove J1 and J2 if an external DAI power supply is used! DAI GROUP SAVE SAVE 2
1.1 Activation/deactivation of the memory of the last light intensity value P1+ + P1 Press the buttons P1 and at the same time. Activation Deactivation ED4 ED4 = last value = 100% 1.2 Assigning a GROUP to the connected SAVE devices ED 1 2 3 4 P2+ P2 + ED4 (1 s) P2 GROUP ED1 ED2 ED3 ED4 0 1 2 GROUP ED1 ED2 ED3 ED4 8 9 10 ( 3 s) CFIGURED 3 11 Press the buttons P2 and at the same time. 4 5 6 7 12 13 14 15 = default 1.3 Restoring DAI default values of the SAVES P2+ + ( 3s) P2 P2 Press P2 and simultaneously twice and hold them the second time for 3 s. + DAI 1 s 3 DEFAUT VAUE POWER EVE: 0 MIIMUM EVE: 85 (1%) MAXIMUM EVE: 254 (100%) FADE TIME: 1 FADE RATE: 1 SYSTEM FAIURE EVE: 254 (100%)
2 Wireless command devices 100% 100% 75% 50% Min. 75% 50% Min. / / / / 7/42 channels transmitter 3/6/18 channels transmitter Green Mouse Transmitter with integrated light sensor See the product s instructions for details. Single command channel with function, or //DIM 4
2.1 Radio codes memorization TYPE OF MEMORIZATI (see description p.4) P2 keep it pressed 7 channels x1 1 button: < 1 s / 1 button with function 1 button with function > 1 s DIMMER ꜛ ꜜ x2 x3 x4 Press the button of the transmitter relative to the code to memorize.... intermittent sound 3 channels x5 Green Mouse x6 The buzzer will make a beep each press. 5
2.2 Radio codes deletion TYPE OF DEETI keep it pressed... intermittent sound Single radio code x1 Press the button of the transmitter relative to the code to delete. All the radio codes x2 (10 s) 2.3 Modification of the preset light values of a 7/42 channel transmitter If any transmitter with modified light values is used in the remote memorization (3.1), the added transmitter will have the same modified values. 1 2 3 ED ED ( 5 s) 1. Press the button relative to the value to modify (..). 2. Adjust the value with buttons and. 3. Press and keep it pressed for 5s. The buzzer will make a beep each press. 6
3.1 Remote memorization of further radio codes memorized memorized new intermittent sound button is located inside the transmitter. The added radio code will have the same functions of the code used for the memorization. This procedure is compatible with any type of transmitter. < 5 s Press the button of the memorized transmitter. Press the button relative to a memorized code. Press the button relative to the new code. 1 s < 5 s... 3.2 Remote deletion of a radio code memorized intermittent sound button is located inside the transmitter. x 3... 1 s < 5 s Press three times the button of the memorized transmitter. Press the button relative to the code to delete. 7
1 2 3 4 5 6 7 8 9 10 11 12 13 14 4 SCEES programming Example - address 1 2 3 100% address 2 4 5 25% 75% address 1 2 4 50% 100% 2 address 3 5 100% 7/42 c. scene 1 scene 2 scene 3 scene 4 ID: 1..20 Setting the address of the receiver (1..20) P1+P2 Tens P1 + P2 address Units ED3 ED2 ED1... P1 Press the buttons P1 and P2 at the same time. The flashing of ED2 and ED3 shows the address. Press as many times as the address to assign. Confirm with P1. ED1 turns off each press. 8
Modification of the preset light values of a 7/42 channel transmitter memorized in more than one receiver 1 ( 5 s) 2 + - address x RECEIVER...... y z OK! Press the button,, or and keep it pressed 5 s. Select the receiver with or. The selected dimmer will have the load. 3 x... RECEIVER y... z 4 + - intensity or 1 time 2 times Press the button relative to the value to modify (..). Adjust the value with and, or press the same button (..) for or UAFFECTED. 5 Press for memorizing. In order to modify further scenes, repeat the steps 2..5, otherwise... 6 Exit by 9
WARIG: READ CAREFUY THIS ISTRUCTIS BEFORE ISTAIG AD COMMISSIIG THE PRODUCT. SAVE THESE ISTRUCTIS FOR FUTURE REFERECE. PRODUCT ISTAATI The product at issue must be installed, commissioned and maintained only by licensed and authorised people, respecting the laws concerning the electrical installations. ot conforming installations, wrong adjustments or product alterations may cause fire, electric shock, or personal injuries. The manufacturer is not responsible for any damage due to wrong installation or improper use. EECTRICA CECTIS All the connections must be rated for a singlephase 110-230Vac power supply, with the relative Earth connection. For the disconnection from the power line, use an all-pole switch with contacts having a dimension of at least 3,5mm. Arrange all the necessary safety devices and use only materials complying with the standard of electrical installations. The cable must have a section properly rated according to the load connected. Attention: If any cable is damaged, it must be immediately replaced by a qualified person in order to avoid any hazard. manufacturer reserves the right for changing technical data and features without prior notice. 10 SAFETY IFORMATI Do not operate in the high voltage area of the electronic board, when it is supplied. Use the product only in combination with devices which can guarantee a safe extended time functioning. The radio signal reception of the device could be disturbed by the presence of electrical disturbances being transmitted by other appliances working on the same frequency or if the product is somehow shielded by metal parts. PRODUCT DISPOSA At the end of this product s useful life, it must not be disposed of as domestic waste, but must be taken to a collection centre for waste electrical and electronic equipment. It is the user s responsibility to dispose of this appliance through the appropriate channels at the end of its useful life. Failure to do so may incur the penalties established by laws governing waste disposal. Hereby automation s.r.l. declares that the product complies with the essential requirements and other relevant provisions, established by the Directive 1999/5/EC. In the view of a constant development of their products, the manufacturer reserves the right for changing technical data and features without prior notice.
Technical specifications Power supply 110-230V~ Max. DAI BUS output power 22V - 80mA = 20 SAVES (TVDMAxxxA01) 22V - 250mA = 64 SAVES (TVDMAxxxA02) The connection cables must have a section suitable to the maximum load applied to the output ( 1mm², 300m), and to the additional devices connected to the input ( 100m). Protection rating IP20 Operating temperature range -20 C / +50 C Reception frequency 868.3 MHz (TVDMA868A0x) 916 MHz (TVDMA916A0x) Radio memory capability (transmitters) 42