NOTE: CLEAN GLOVES MUST BE WORN DURING INSTALLATION. DO NOT REMOVE PAPER FROM ACRYLIC DIFFUSER UNTIL INSTALLATION IS COMPLETE. J-BOX & CEILING CANOPY MOUNTING PLATE TEMPORARY CHAINS LABELED CABLE & CORD HOLES CANOPY w/ MOUNTED POWER SUPPLIES AND WIRES. (FIXTURES VARY, NOT ALL ARE SHOWN) ELEC. CORD STRAIN RELIEF SUSPENSION CABLES UPPER DIFFUSER CABLE ADJUSTERS NOTE: DO NOT OVERTIGHTEN SCREWS LIGHT BAR LOWER DIFFUSER 8-32 x 3/16" CONE POINT SET SCREW
NOTE: CLEAN GLOVES MUST BE WORN DURING INSTALLATION. DO NOT REMOVE PAPER FROM ACRYLIC DIFFUSER UNTIL INSTALLATION IS COMPLETE. CONTENTS (1) Rectangular Canopy 36" L x 18" W (1) Canopy Mouting Frame (3) Light Bar, Electrical Cord and pre-installed Strain Relief with Set Screw (3) Lower Acrylic Diffuser (3) Upper Acrylic Diffuser (6) Suspension Cables, Labeled and pre-marked with insertion depth (4) Canopy Mounting Screws (#10-32) (4) Temporary Chains w/ S-Hooks (3) Hex Wrench 1/16, 5/64, 1/8 (4) Sets of Gloves to be worn during installation. NOTE: DO NOT OVERTIGHTEN SCREWS UL Approved in US and Canada
PLEASE USE THE FOLLOWING DIAGRAM AND STEPS FOR INSTALLATION NOTE: CLEAN GLOVES MUST BE WORN DURING INSTALLATION. DO NOT REMOVE PAPER FROM ACRYLIC DIFFUSER UNTIL INSTALLATION IS COMPLETE. INSTRUCTIONS 1. Determine fixture location, J Box should be located on the center of the Fixture. 2. Screw Canopy Mounting Plate to ceiling w/ appropriate screws and/or anchors per installation requirements. (Mounting requirements and hardware to be determined and provided by installer) 3. Hang Temporary Chains from Canopy Mounting Plate; raise Canopy to hang from Temporary Chains, note alignment mark on Canopy Mounting Plate and Canopy. NOTE: TEMPORARY CHAINS ARE NOT MEANT TO BE LEFT SUSPENDING THE FIXTURE FOR EXTENDED PERIODS OF TIME 4. Connect 110-277 Volt power to pre-wired fixture (black and white wires). All power supplies have been installed by manufacturer. The drivers installed in this unit have multiple methods of dimming to accommodate your needs. The systems are capable of Triac dimming at 120 VAC or have the option for 0-10 vdc current-sinking control for dimming. 5. Make Electrical connections to fixture based on dimming type or controls with provided wiring diagrams supplied with dimming or control options. (See next page for diagrams.) This fixture can be wired to accept Triac dimming or 0-10V dimming or switch (the 0-10V dimming signal must be supplied to the purple and gray wires as there is no reference voltage supplied from the driver for this dimming option)). If no dimming is required cap gray and purple wires from the driver and install a nondimming switch wired per switch instructions. 6. Slide the labeled Suspension Cables into corresponding holes through top of Canopy. 7. Match the Light Bars to their corresponding labels in the Canopy and hang all Light Bars from the Suspension Cables with Cable Adjusters to the insertion depth marked on the Cables. 8. Loosen Set Screws pre-installed in Strain Reliefs with provided Hex Wrench. 9. Uncoil silver cloth covered Elec. Cord and feed through Strain Reliefs. Snug the set screw in the Strain Relief against the Cord when the Cord is hanging straight---do NOT OVERTIGHTEN. 10. Make electrical connections with Snap Connectors at labeled positions in Canopy. Connect to Supply Power with wire nuts and Ground to Canopy. 11. Remove pre-installed 8-32 x 3/16" Cone Point Set Screws from ends of Light Bars using provided Hex Wrench. Reaise each numbered Lower Diffuser to the corresponding Light Bar and secure into bottom slot by re-installing Cone Point Set Screws. DO NOT OVERTIGHTEN SCREWS. 12. Install Upper Diffusers into Light Bars. 13. Remove Temporary Chains and raise the Canopy to the Canopy Mounting Plate. Secure with provided 10-32 screws (start all screws before final tightening). 14. Based on site conditions, a slight leveling of Light Bars may be necessary. Pressing the center cylinder of the Cable Adjuster will release pressure on the Cable and Light Bar can be repositioned.
HOLLY HUNT STUDIO NOTE: CLEAN GLOVES MUST BE WORN DURING INSTALLATION. DO NOT REMOVE PAPER FROM ACRYLIC DIFFUSER UNTIL INSTALLATION IS COMPLETE. 0-10V Dimmer Switch Ref. Control Module Light Bar Below Light Bar Below REFERENCE WIRING DIAGRAM FOR 0-10V DIMMING To 120/240V J-Box Wire Nut Light Bar Below Light Bar Below REFERENCE WIRING DIAGRAM WITHOUT DIMMING REFERENCE TRIAC WIRING DIAGRAM Triac Dimmer Wire Nut Light Bar Below Light Bar Below
NOTE: CLEAN GLOVES MUST BE WORN DURING INSTALLATION. DO NOT REMOVE PAPER FROM ACRYLIC DIFFUSER UNTIL INSTALLATION IS COMPLETE. J-BOX & CEILING CANOPY MOUNTING PLATE TEMPORARY CHAINS LABELED CABLE & CORD HOLES CANOPY w/ MOUNTED POWER SUPPLIES AND WIRES. (FIXTURES VARY, NOT ALL ARE SHOWN) ELEC. CORD STRAIN RELIEF SUSPENSION CABLES UPPER DIFFUSER CABLE ADJUSTERS NOTE: DO NOT OVERTIGHTEN SCREWS LIGHT BAR LOWER DIFFUSER 8-32 x 3/16" CONE POINT SET SCREW
CONTENTS (1) Rectangular Canopy 72" L x 18" W (1) Canopy Mouting Frame (5) Light Bar, Electrical Cord (5) Strain Reliefs with Nylon Tip Set Screw Installed (5) Lower Acrylic Diffuser (5) Upper Acrylic Diffuser (10) Suspension Cables, Labeled and pre-marked with insertion depth (6) Canopy Mounting Screws (#10-32) (4) Temporary Chains w/ S-Hooks (3) Hex Wrench 1/8", 1/16" and 5/64" (4) Sets of Gloves to be worn during installation. (2) Extra Butt Connector (2) 8-32 x 3/16 or 1/4 Cone Point SS, Pre-installed per Light Bar (5) Wire Nuts NOTE: CLEAN GLOVES MUST BE WORN DURING INSTALLATION. DO NOT REMOVE PAPER FROM ACRYLIC DIFFUSER UNTIL INSTALLATION IS COMPLETE. NOTE: DO NOT OVERTIGHTEN SCREWS UL Approved in US and Canada
PLEASE USE THE FOLLOWING DIAGRAM AND STEPS FOR INSTALLATION NOTE: CLEAN GLOVES MUST BE WORN DURING INSTALLATION. DO NOT REMOVE PAPER FROM ACRYLIC DIFFUSER UNTIL INSTALLATION IS COMPLETE. INSTRUCTIONS 1. Determine fixture location, J Box should be located on the center of the Fixture. 2. Screw Canopy Mounting Plate to ceiling w/ appropriate screws and/or anchors per installation requirements. (Mounting requirements and hardware to be determined and provided by installer) 3. Hang Temporary Chains from Canopy Mounting Plate; raise Canopy to hang from Temporary Chains, note alignment mark on Canopy Mounting Plate and Canopy. NOTE: TEMPORARY CHAINS ARE NOT MEANT TO BE LEFT SUSPENDING THE FIXTURE FOR EXTENDED PERIODS OF TIME 4. Connect 110-277 Volt power to pre-wired fixture (black and white wires). All power supplies have been installed by manufacturer. The drivers installed in this unit have multiple methods of dimming to accommodate your needs. The systems are capable of Triac dimming at 120 VAC or have the option for 0-10 vdc current-sinking control for dimming. 5. Make Electrical connections to fixture based on dimming type or controls with provided wiring diagrams supplied with dimming or control options. (See next page for diagrams.) This fixture can be wired to accept Triac dimming or 0-10V dimming or switch (the 0-10V dimming signal must be supplied to the purple and gray wires as there is no reference voltage supplied from the driver for this dimming option)). If no dimming is required cap gray and purple wires from the driver and install a nondimming switch wired per switch instructions. 6. Slide the labeled Suspension Cables into corresponding holes through top of Canopy. 7. Match the Light Bars to their corresponding labels in the Canopy and hang all Light Bars from the Suspension Cables with Cable Adjusters to the insertion depth marked on the Cables. 8. Loosen Set Screws pre-installed in Strain Reliefs with provided Hex Wrench. 9. Uncoil silver cloth covered Elec. Cord and feed through Strain Reliefs. Snug the set screw in the Strain Relief against the Cord when the Cord is hanging straight---do NOT OVERTIGHTEN. 10. Make electrical connections with Snap Connectors at labeled positions in Canopy. Connect to Supply Power with wire nuts and Ground to Canopy. 11. Remove pre-installed 8-32 x 3/16" Cone Point Set Screws from ends of Light Bars using provided Hex Wrench. Reaise each numbered Lower Diffuser to the corresponding Light Bar and secure into bottom slot by re-installing Cone Point Set Screws. DO NOT OVERTIGHTEN SCREWS. 12. Install Upper Diffusers into Light Bars. 13. Remove Temporary Chains and raise the Canopy to the Canopy Mounting Plate. Secure with provided 10-32 screws (start all screws before final tightening). 14. Based on site conditions, a slight leveling of Light Bars may be necessary. Pressing the center cylinder of the Cable Adjuster will release pressure on the Cable and Light Bar can be repositioned.
HOLLY HUNT STUDIO NOTE: CLEAN GLOVES MUST BE WORN DURING INSTALLATION. DO NOT REMOVE PAPER FROM ACRYLIC DIFFUSER UNTIL INSTALLATION IS COMPLETE. 0-10V Dimmer Switch Ref. Control Module Light Bar Below Light Bar Below REFERENCE WIRING DIAGRAM FOR 0-10V DIMMING To 120/240V J-Box Wire Nut Light Bar Below Light Bar Below REFERENCE WIRING DIAGRAM WITHOUT DIMMING REFERENCE TRIAC WIRING DIAGRAM Triac Dimmer Wire Nut Light Bar Below Light Bar Below
NOTE: CLEAN GLOVES MUST BE WORN DURING INSTALLATION. DO NOT REMOVE PAPER FROM ACRYLIC DIFFUSER UNTIL INSTALLATION IS COMPLETE. J-BOX & CEILING CANOPY MOUNTING PLATE TEMPORARY CHAINS LABELED CABLE & CORD HOLES CANOPY w/ MOUNTED POWER SUPPLIES AND WIRES. (FIXTURES VARY, NOT ALL ARE SHOWN) ELEC. CORD STRAIN RELIEF SUSPENSION CABLES UPPER DIFFUSER CABLE ADJUSTERS NOTE: DO NOT OVERTIGHTEN SCREWS LIGHT BAR LOWER DIFFUSER CONE POINT SET SCREW
NOTE: CLEAN GLOVES MUST BE WORN DURING INSTALLATION. DO NOT REMOVE PAPER FROM ACRYLIC DIFFUSER UNTIL INSTALLATION IS COMPLETE. CONTENTS (1) Rectangular Canopy 108" L x 18" W (1) Canopy Mouting Frame (7) Light Bar, Electrical Cord and pre-installed Strain Relief with Set Screw (7) Lower Acrylic Diffuser (7) Upper Acrylic Diffuser (14) Suspension Cables, Labeled and pre-marked with insertion depth (10) Canopy Mounting Screws (#10-32) (4) Temporary Chains w/ S-Hooks (1) Hex Wrench (4) Sets of Gloves to be worn during installation. NOTE: DO NOT OVERTIGHTEN SCREWS UL Approved in US and Canada
PLEASE USE THE FOLLOWING DIAGRAM AND STEPS FOR INSTALLATION NOTE: CLEAN GLOVES MUST BE WORN DURING INSTALLATION. DO NOT REMOVE PAPER FROM ACRYLIC DIFFUSER UNTIL INSTALLATION IS COMPLETE. INSTRUCTIONS 1. Determine fixture location, J Box should be located on the center of the Fixture. 2. Screw Canopy Mounting Plate to ceiling w/ appropriate screws and/or anchors per installation requirements. (Mounting requirements and hardware to be determined and provided by installer) 3. Hang Temporary Chains from Canopy Mounting Plate; raise Canopy to hang from Temporary Chains, note alignment mark on Canopy Mounting Plate and Canopy. NOTE: TEMPORARY CHAINS ARE NOT MEANT TO BE LEFT SUSPENDING THE FIXTURE FOR EXTENDED PERIODS OF TIME 4. Connect 110-277 Volt power to pre-wired fixture (black and white wires). All power supplies have been installed by manufacturer. The drivers installed in this unit have multiple methods of dimming to accommodate your needs. The systems are capable of Triac dimming at 120 VAC or have the option for 0-10 vdc current-sinking control for dimming. 5. Make Electrical connections to fixture based on dimming type or controls with provided wiring diagrams supplied with dimming or control options. (See next page for diagrams.) This fixture can be wired to accept Triac dimming or 0-10V dimming or switch (the 0-10V dimming signal must be supplied to the purple and gray wires as there is no reference voltage supplied from the driver for this dimming option)). If no dimming is required cap gray and purple wires from the driver and install a nondimming switch wired per switch instructions. 6. Slide the labeled Suspension Cables into corresponding holes through top of Canopy. 7. Match the Light Bars to their corresponding labels in the Canopy and hang all Light Bars from the Suspension Cables with Cable Adjusters to the insertion depth marked on the Cables. 8. Loosen Set Screws pre-installed in Strain Reliefs with provided Hex Wrench. 9. Uncoil silver cloth covered Elec. Cord and feed through Strain Reliefs. Snug the set screw in the Strain Relief against the Cord when the Cord is hanging straight---do NOT OVERTIGHTEN. 10. Make electrical connections with Snap Connectors at labeled positions in Canopy. Connect to Supply Power with wire nuts and Ground to Canopy. 11. Remove pre-installed 8-32 x 3/16" Cone Point Set Screws from ends of Light Bars using provided Hex Wrench. Reaise each numbered Lower Diffuser to the corresponding Light Bar and secure into bottom slot by re-installing Cone Point Set Screws. DO NOT OVERTIGHTEN SCREWS. 12. Install Upper Diffusers into Light Bars. 13. Remove Temporary Chains and raise the Canopy to the Canopy Mounting Plate. Secure with provided 10-32 screws (start all screws before final tightening). 14. Based on site conditions, a slight leveling of Light Bars may be necessary. Pressing the center cylinder of the Cable Adjuster will release pressure on the Cable and Light Bar can be repositioned.
HOLLY HUNT STUDIO NOTE: CLEAN GLOVES MUST BE WORN DURING INSTALLATION. DO NOT REMOVE PAPER FROM ACRYLIC DIFFUSER UNTIL INSTALLATION IS COMPLETE. 0-10V Dimmer Switch Ref. Control Module Light Bar Below Light Bar Below REFERENCE WIRING DIAGRAM FOR 0-10V DIMMING To 120/240V J-Box Wire Nut Light Bar Below Light Bar Below REFERENCE WIRING DIAGRAM WITHOUT DIMMING REFERENCE TRIAC WIRING DIAGRAM Triac Dimmer Wire Nut Light Bar Below Light Bar Below