Osaka Drawer Chest Assembly Instructions - Please keep for future reference White Black 00 Dimensions Width : Depth : Height: 0. cm 0.0 cm. cm Assembly Instructions - Please keep for future reference If you need help or have damaged or missing parts, call the Argos Customer Helpline: 0 0 0 0 0 Issue - -0-0
! Safety and re Advice Important - Please read these instructions fully before starting assembly Check you have all the components and tools listed on pages and. Remove all fittings from the plastic bags and separate them into their groups. Keep children and animals away from the work area, small parts could choke if swallowed. Make sure you have enough space to layout the parts before starting. Do not stand or put weight on the product, this could cause damage. Assemble the item as close to its final position (in the same room) as possible. Assemble on a soft level surface to avoid damaging the unit or your floor. Parts of the assembly will be easier with people. We do not recommend the use of power drill/drivers for inserting screws, as this could damage the unit. Only use hand screwdrivers. Dispose of all packaging carefully and responsibly. re and maintenance Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners. From time to time check that there are no loose screws on this unit. This product should not be discarded with household waste. Take to your local authority waste disposal centre. Note: if required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
Components - Panels If you have damaged or missing components, call the Argos Customer Helpline: 0 0 0 0 Please check you have all the panels listed below Top (0, cm x 0 cm) Front rail (, cm x cm) Back rail (, cm x cm) Side, left (, cm x cm) Side, right (, cm x cm) Drawer front x (, cm x, cm) Drawer side, right/left ( cm x cm) x Back x (0,0 cm x, cm) 0 Drawer back ( cm x cm) x Post x (0, cm x, cm) Drawer bottom x (,0 cm x, cm) H-Profile (,0 cm x, cm) 0-0
Components - ttings Please check you have all the panels listed below Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required. Ab Bp ø. x 0mm Wooden dowel x ø x 0mm Wooden dowel x ø x mm Screw x Di ø x 0.mm m x ø x, ccmm Bolt x Ge. x mm Nail x Hd Back fitting w. ø. x mm Screw x Hk ø x mm Metal Knob x M x 0mm Screw x M x mm Screw x ø x mm Screw x ø. x mm Screw x Vl ø, x,mm Screw x x x 0mm Drawer runner x x x mm Angle x Tools required Phillips screwdriver (Medium & large) Hammer Flatblade screwdriver (Medium) Ruler - Use this ruler to help correctly identify the screws 0 0 0 0 0 0 0 0 0 0 00 0 0 0 0 0 0 0 0-0
Step Assembly of the chest. Step. x the posts onto the sides and using screws into the holes indicated. The top of the posts and the sides and must be flush. ø x mm Screw x Step. Knock the dowels into the holes indicated on the sides and using a small hammer. ø. x 0mm Wooden dowel x ø x, ccmm Bolt x Screw the bolts into the holes indicated on the sides and. 0-0
Step. Slide the top of the drawer runners backwards. You can identify the front end of the drawer runner by the two M holes. See details. x the front end of the drawer runners to the sides and using screws through the holes number and as indicated. ø. x mm Screw x Hole no. Hole no. Front end Front end x x 0mm Drawer runner x Hole no. See details. Front end Hole no. Step. Note the hole! Bottom end of right hand side Slide the top of the drawer runners forwards. x the back end of the drawer runners to the sides and using screws through the holes indicated. ø. x mm Screw x See details. 0-0
Step. Vl x the angles Vl using screws into the holes indicated on the front rail. ø, x,mm Screw x x x mm Angle x Vl Vl Step. Knock the dowels into the holes indicated on the back rail using a small hammer. ø. x 0mm Wooden dowel x Step. Screw the bolts into the holes indicated on the top. ø x, ccmm Bolt x Step. Place the sides and onto the back rail. Push cams into the holes indicated on the back rail. Arrows pointing towards the sides /. ø x 0.mm m x Turn the cams to the right to fix the sides and. 0-0
Step. Place the top onto the sides and. ø x 0.mm m x Push cams into the holes indicated on the sides and. Arrows pointing towards the top. Turn the cams to the right to fix the top. Step.0 Place the front rail as shown. x the angles Vl to the sides using screws. See detail. ø, x,mm Screw x 0-0
Step. Place the backs into the rabbet on the top into the H-profile and onto the posts. Distribute equally!. x mm Nail x Di Important!! Make sure the angle between the top and the posts is 0 when the backs is attached. x the backs to the top, the posts and the back rail using nails Di. Di Use a small hammer. Step Assembly of the drawers. 0 x Step. x the drawer sides to the drawer back 0 as shown, using screws Bp. 0 Bp ø x mm Screw x Bp Bp x 0-0
Step. Knock the dowels Ab into the holes indicated on the drawer sides using a smal hammer. Ab ø x 0mm Wooden dowel x Ab Ab x Step. Slide the drawer bottom into the drawer sides. x Step. Screw the bolts into the holes indicated on the drawer front. ø x, ccmm Bolt x x Step. Push the drawer front onto the drawer sides. ø x 0.mm m x Place cams into the holes indicated. Arrow pointing towards the front. Turn the cams to the right to fix the front. x 0-0
Step. Important!! Make sure the angle between the drawer front and the drawer sides is 0 before the drawer bottom is fixed using as shown. 0 Back fitting w. ø. x mm Screw x 0 x To adjust the angle between the drawer sides and the fronts push the fitting sidewards. See details. Step. Ge Hd x the metal knobs Ge to the drawer front using screws Hd. ø x mm Metal Knob x M x 0mm Screw x Ge Ge Hd Hd x Step. Pull out the drawer runners. Slide the drawers onto the runners. Hk M x mm Screw x t and fix the lower drawer first and work your way up. Hk x drawers to the drawer runners using screws Hk. Hk 0-0