GAS HOT GLUE GUN PHKPG 150 A1 Operating and safety instructions IAN 285747
14 1 2 13 3 4 5 12 11 10 9 6 7 8 A B C 1. 3. 2.
Table of contents 1. Scope of delivery / parts list... 04 Description of the parts...04 2. General... 04 Symbols used...04 3. Safety... 05 Appropriate use...05 Safety instructions...05 4. Before Use... 08 Checking the product and scope of delivery...08 Filling the gas tank (Fig. A)...08 Inserting the glue stick (Fig. B)...08 5. Usage... 09 Lighting the hot glue gun (Fig. C)...09 Gluing applications...10 6. After finishing work... 10 7. Storage and transport...11 8. Maintenance and spare parts...11 Maintenance and repairs...11 Cleaning...11 9. Troubleshooting...12 10. Technical specifications...12 11. Disposal...13 Disposing of the used device...13 Disposal of packaging...13 Instructions for disposal of the gas cartridge...13 12. Warranty...13 03
1. Scope of delivery / parts list Description of the parts 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Gas hot glue gun Glue port Gas regulator marking Gas supply regulator Handle Gas refilling valve Trigger Stand Piezo ignition Nozzle Inspection glass for heating chamber Ventilation opening 2 Glue sticks Butane refill cartridge Art. 1500002692 2. General This manual belongs to this product. It contains important information on safety, usage and maintenance. Read the manual carefully before using the product. Pay particular attention to the safety instructions and warnings. Failure to follow the instructions given in the manual may result in serious injuries or damage to the product. Always include the manual when you give the product to others. Keep this manual in a safe place for future reference. Symbols used The following symbols and key words will be used in this manual, on the product or the packaging. Follow the warnings and safety instructions! 04
Read the manual WARNING! Hot surface 3. Safety Appropriate use This product is only suitable for private use in the hobby and craft area for the following purposes: For gluing wood, cardboard and similar materials over a short time period and exclusively with 11 mm Ø glue sticks Any other use of the product is expressly forbidden and is considered as misuse. The manufacturer cannot be held responsible for damage or injury caused by misuse of the product. Examples of misuse are given in the following non-exhaustive list: Use of unsuitable accessories Use and maintenance of the product by someone who is not familiar with the product and/or who lacks suitable experience commercial, business-related, industrial or excessive use of the product Use the accessories according to these instructions. Failure to follow the instructions in the manual may lead to serious injury and may invalidate the guarantee. Comply with applicable local or national regulations concerning the use of this product. Do not make any modifications to the product. Any modification to the product may be dangerous and is prohibited. Safety instructions WARNING! Read the safety instructions carefully. Failure to follow the safety warnings and instructions may result in fire, explosion and/or serious injuries. 05
06 a. Always keep the hot glue gun out of reach of children. b. Keep the hot glue gun away from your face and away from your clothing when lighting. c. The nozzle and other accessible parts are very hot even after the flame has gone out. Do not touch. d. Do not expose the hot glue gun to heat more than 50 C or to sunlight for a long time. e. The hot glue gun is designed for private use in the hobby and craft area and for brief durations and is not suitable for long-duration use. Switch off the hot glue gun during breaks and after a maximum of half an hour of usage for complete cooling by closing the gas supply regulator. f. Never work overhead. Hot, molten glue could drip down and injure you. g. Use the hot glue gun only in well-ventilated places and away from ignition sources or flammable objects. h. Do not use the hot glue gun if it is leaking or damaged, or if it is not working properly. i. Do not disassemble or open the hot glue gun. j. Do not make any modifications to the hot glue gun. The assembly and factory settings should not be altered. Only replacement parts recommended by the manufacturer may be used. It can be dangerous to modify the settings or make changes to the hot glue gun, to remove parts or to use replacement parts other than those recommended by the manufacturer. k. Repairs to the hot glue gun should only be carried out by the manufacturer or by an authorised service centre. l. Switch off the hot glue gun and place it in its stand during breaks and when not in use. m. Wait for one minute after refilling before lighting the hot glue gun. n. Be careful when using the hot glue gun near flammable materials and remember that heat can be conducted to concealed flammable materials. o. Never leave the hot glue gun unattended when switched on. p. Ensure that the flame is completely extinguished after use. Open the stand of the hot glue gun and allow the hot glue gun to cool down completely on the stand before putting it away. Otherwise there is risk of fire. q. The filled gas tank contains flammable pressurised gas. Take care not to heat the refillable gas tank. Do not expose the hot glue gun to temperatures exceeding 50 C / 120 F or to prolonged sunlight. Otherwise there is risk of bursting or explosion. r. Read the refilling instructions carefully. Incorrect refilling may lead to accidents.
s. Do not use the hot glue gun in surroundings where flammable fumes, flammable liquids or explosive materials are present. Otherwise there is risk of fire or explosion. t. Do not light the hot glue gun near your face, hands, clothing or flammable materials. Do not light and direct the hot glue gun at others. Otherwise there is risk of burns. u. Maintain a safe distance of at least 0.5 m on the side from all objects, as well as a min. distance of 1 m from objects over the device. v. The air outlet of the hot glue gun releases hot air. Ensure that the hot glue gun is always switched off and placed on the integrated stand even during short breaks, to avoid igniting the work surface or other objects. Do not direct the hot air outlets towards your eyes, face or others. Otherwise there is risk of burns. w. Do not inhale the fumes, as they may be poisonous. x. The glue nozzle becomes extremely hot during and remains hot for a period after use. Take care to protect yourself from accidental burns. y. Risk of burns! Do not touch the hot glue or the nozzle with your fingers. Never point the hot glue gun towards others or animals - the hot glue should not come into contact with persons or animals. z. If hot glue comes into contact with your skin, hold the affected area under cold running water. Do not attempt to pull off any glue which is stuck to the skin. aa. Never attempt to pull glue sticks out of the device. bb. Never use inflammable liquids to clean the workpieces. cc. This device is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge. Children should be supervised to ensure that they do not play with the device. 07
4. Before Use Checking the product and scope of delivery Take the hot glue gun and accessories out of the packaging Check whether the delivery is complete (see chapter "Scope of delivery / parts list") Check the hot glue gun and accessories for damages. Do not use the hot glue gun if it is damaged or parts are missing. Contact the manufacturer via the service centre listed in the "Warranty" chapter. Filling the gas tank (Fig. A) Caution! Danger of fire, burning and/or explosion! Switch off the hot glue gun by closing the gas supply regulator and ensure that the flame is off. Allow the hot glue gun to cool completely. Fill the tank in a well ventilated place, in an area free of flames or sources of ignition and at a safe distance from others. Smoking is prohibited when filling the tank. Use only butane refill cartridges, for example commercially available cigarette lighter gas. Do not use pure isobutane or propanebutane mixes. Place the nozzle of the gas canister against the gas refill valve (6) and press it in. Use a suitable adapter if necessary. Take the nozzle of the gas canister out of the refill valve of the device before the gas begins to flow out. Wait for at least a minute before igniting the gun for the first time to allow the gas to stabilise. Inserting the glue stick (Fig. B) Insert a glue stick into the glue port (2) as shown. 08
5. Usage Lighting the hot glue gun (Fig. C) Push the gas supply regulator (4) upwards and turn it to the right using your thumb until the valve is completely open. Now press the piezo ignition (9) immediately. Look through the inspection glass (11) to see if the hot glue gun has ignited successfully. If yes, the heating chamber will be glowing red. The brightness may vary slightly depending on the level of the gas in the tank and depending on the quality of the gas used. DANGER! In case the hot glue gun does not ignite successfully after numerous five attempts, close the gas supply regulator immediately to stop the gas flow and refer to the "Troubleshooting" chapter. 1 Gas supply open Inspection glass 3 2 Ignition Note! Risk of damage! Always switch off the hot glue gun and place it on the integrated stand even during short breaks. Never use the hot glue gun for more than 30 minutes. After this, allow the hot glue gun to cool down completely before using it again. 09
Gluing applications Before gluing The surfaces to be glued must be clean, dry and free of grease. Clean the gluing surfaces before applying the glue if necessary. Polished or shiny surfaces should be roughened before gluing. Gluing Note! Practice before you start working with the glue gun. Carry out trials on waste material. The correct amount of glue and the feed rate for each application depend on the size and properties of the materials you wish to glue and can only be determined by carrying out trials. Insert a glue stick into the glue port as described above. Press the trigger (7) to move the glue stick into the heating chamber. Allow the heating chamber and the glue stick to heat up for 2-3 minutes until the glue melts. Press the trigger to apply glue to the gluing surface. After gluing After applying glue, bring the workpieces together and press them firmly. Use a clamp or similar fixture if required. The clamping fixture can be removed after about 5 minutes. Allow any surplus glue to cool down completely and subsequently remove it with a knife. 6. After finishing work Note! Risk of damage! After completing the work, switch off the hot glue gun and press the trigger repeatedly to completely use up any residue of the glue stick that may be present, thus emptying the heating chamber. Place the hot glue gun on the integrated stand and allow it to cool completely. 10
7. Storage and transport Clean the hot glue gun before storage. If the hot glue gun is not being used, keep it in a safe, cool, dry and well-ventilated place, out of the reach of children. Store the hot glue gun and accessories in its original packaging or similar suitable packaging. 8. Maintenance and spare parts Maintenance and repairs The product requires very little maintenance. Repairs should only be carried out by qualified technicians or by an authorised service centre. Qualified technicians must have relevant training and experience, be familiar with the design and construction requirements of the product and understand and follow the safety regulations. Cleaning Caution! NEVER immerse the hot glue gun in water. Allow the hot glue gun to cool completely before you start cleaning. Clean the product with a moist cloth. Never use strong and / or abrasive cleaning agents or solvents. Allow all the parts to dry completely. Ensure that water does not get into the product. 11
9. Troubleshooting Problem Possible cause Solutions, tips The hot glue gun is not The gas tank is empty. Allow the device to cool and fill the igniting. gas tank. The gas supply regulator (2) is not open or not open sufficiently. Catalyst is used up. Open the gas supply regulator (or open further if necessary). The hot glue gun is provided with a palladium-loaded catalyst which allows the gas to burn flamelessly. The catalyst is designed for long service life. Once the catalyst is used up, the device can either be disposed of or you can get a new catalyst installed at the service centre by paying the corresponding charges. 10. Technical specifications Model: Device category: Rated power: Consumption: Operating temperature: Diameter of the glue sticks: PHKPG 150 A1 Direct pressure butane 128 W approx. 10 g / h +10 c +40 c 11 mm 12
11. Disposal Disposing of the used device If the product can no longer be used, then all the consumers are required by law to bring the old device to a separate waste collection point, for example in their community or district, and not to dispose of it in the household waste. This ensures that the old devices are properly recycled and negative impact on the environment is avoided. Disposal of packaging Dispose of the packaging material according to the type of material and according to any local regulations. Instructions for disposal of the gas cartridge Do not forcibly open the gas cartridge or burn it after use. Gas cartridges which are completely empty can be sent to the municipal waste collection centre or disposed of along with domestic waste. Gas cartridges which are not completely empty should be disposed of as special waste according to the waste disposal regulations. Please contact your local municipal authority for further information. 12. Warranty Warranty provided by Walter Werkzeuge Salzburg GmbH Dear customer, This device comes with a 3 year warranty from the date of purchase. In case of defects in the product you may be entitled to legal claims against the seller of the product. These legal claims are not restricted by the following warranty. Conditions of warranty The warranty period begins with the date of purchase. Please preserve the original sales receipt. This document is required as proof of purchase. If a material or fabrication defect occurs in this product within three years from the date of purchase, the product shall be 13
repaired or replaced free of cost at our discretion. Within the three year period the warranty requires the defective product and the purchase document (sales receipt) to be provided with a brief written description of where the defect lies and when it occurred. If the defect is covered by our warranty, the repaired product or a new product shall be returned to you. A new warranty period does not begin with the repair or exchange of the product. Warranty period and legal claims based on defects The warranty period is not extended by the warranty. This also applies to replaced and repaired parts. Any damages and defects that may exist at the time of purchase must be notified immediately after removal from packaging. Any repairs arising after the expiry of the warranty period are chargeable. Scope of the warranty The device has been manufactured according to strict quality guidelines and tested diligently before delivery. The warranty applies to material or fabrication defects. This warranty does not cover product parts that are subject to normal wear and tear and therefore can be considered as parts subject to wear and tear or for the damage to fragile parts, e.g switch, batteries or those made of glass. This warranty is void if the product is damaged, not used or maintained properly. All the instructions provided in the operating manual must be followed exactly for proper use of the product. The purpose of use and actions which are advised or warned against must necessarily be avoided. The product is intended solely for private use and not for professional use. The warranty is void in case of misuse or improper handling, use of force and changes that have not been carried out by our authorised service centre. Processing a warranty case To ensure quick processing of your issue, please follow the below instructions: Please be ready with the sales receipt and the product number (e.g. IAN 12345) as proof or purchase for all queries. You can refer the product number from the type label,, an engraving, on the cover sheet of your operating instructions (below left) or as sticker on the back or lower side. If functional or other defects occur, first call or email the following service department. You can then send a product recorded as defective postage free along the the sales receipt and information about where the defect lies and when it has occurred, to the service centre address provided to you. This and many other manuals, product videos and software can be downloaded at www. lidl-service.com 14
Service Walter Tools (GB) Ltd. E-Mail: service@walteronline.com Tel.: 00800 925 837 88 IAN 285747 Supplier: Please note that the following address is not a service centre address Please contact the above-mentioned service centre first. Walter Werkzeuge Salzburg GmbH Gewerbeparkstrasse 9 5081 Anif Austria 15
Walter Werkzeuge Salzburg GmbH Gewerbeparkstrasse 9 5081 Anif, Austria V. 1.0 Last Information Update: 06/2017 IAN 285747