Hearts ed With Poster Frame ssembly Instructions - Please keep for future reference 2/80 /9 imensions Width - 97cm epth - 9cm Height - 89cm Important - Please read these instructions fully before starting assembly If you need help or have damaged or missing parts, call the ustomer Helpline: rgos = 0 0 0800 Issue - 08//0/
Safety and are dvice Important - Please read these instructions fully before starting assembly IMPORTNT! KEEP FOR FUTURE REFERENE Keep children and animals away from the work area, small parts could choke if swallowed. heck you have all the components and tools listed on the following pages. uring assembly do not stand or put weight on the product, this could cause damage. Remove all fittings from the plastic bags and separate them into their groups. ssemble the item as close to its final position (in the same room) as possible. Make sure you have enough space to layout the parts before starting. We do not recommend the use of power drill/drivers for inserting screws, as this could damage the unit. Only use hand screwdrivers. ssemble on a soft level surface to avoid damaging the unit or your floor. Parts of the assembly will be easier with 2 people. Unit weight: 20. kgs. are and maintenance From time to time check that there are no loose screws on this unit. This product should not be discarded with household waste. Take to your local authority waste disposal centre. Regularly check and ensure that all bolts and fittings are tightened properly. Prohibit your children from bouncing and jumping on the bed. o not use this child s bed if any part is broken, torn or missing. The recommended mattress size is L900 x W90 mm. o not place this child s bed near heat sources, windows (blind cords, curtain pulls or other strings or cords) and other furniture THIS E OMPLIES WITH S809:2008+:20 Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners. Warnings This product should only be used on firm, level ground. Make sure the legs remain in contact with the ground. Not suitable for children under years. Place the bed tight to any wall or have a gap of 00mm between the wall and the side of the bed. Handy Hints ssemble all parts and bolts loosely during assembly, only once the product is complete should you fully tighten the bolts. Manufacturer: L Packaging o. Ltd. Regularly check and ensure that all bolts and fittings are tightend properly. Note: if required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
omponents - Parts If you have damaged or missing components, call the ustomer Helpline: rgos = 0 0 0800 Please check you have all the parts listed below Headboard (9 x x.2cm) 2 Footboard (9 x 7 x.2cm) Headboard leg x 2 (8 x Ø.2cm) Siderail x 2 Headboard Upper Post x 2 Footboard Upper Post x 2 7 Top Rail Long x 2 8 Top Rail Short x 2 9 Slat x 2 (9. x x 2.cm) (20 x. x Ø.2cm) (87. x Ø.cm) (00 x. x Ø.2cm) (9 x Ø.cm) (9 x x 2.cm) 2
omponents - Fittings Please check you have all the fittings listed below Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required. M x mm olt x M x 2mm olt x M x 2mm olt x 2 E F Mattress stopper x olt nut x llen key x 2 Ruler - Use this ruler to help correctly identify the screws 0 0 20 2 0 0 0 0 70 7 80 8 90 9 00 0 0 20 2 0 0 0 0 70
ssembly Instructions Step ssembling headboard legs Insert headboard legs into holes on headboard as shown. Step 2 ssembling headboard ttach siderails to headboard & as shown and fix through holes using bolts and bolt nuts. Fasten bolts & nuts using 2 allen keys F but do not fully tighten at this stage.
ssembly Instructions Step ssembling footboard 2 ttach footboard 2 to siderails as shown and fix through2 holes using bolts. Fasten bolts using allen key F but do not fully tighten at this stage. 2 Step 8 ssembling short top rails ttach upper posts 8 & into holes on short top rail 8 as shown and fix through holes using bolts. Fasten bolts nuts using allen key F but do not fully tighten at this stage. 8
ssembly Instructions a: Step ttaching upper rails a: Insert headboard upper post onto posts of headboard as shown. b: Fix through holes Fasten bolts using allen key F but do not fully tighten at this stage. b: using bolts as shown. Repeat above steps to assemble the footboard upper post. Step ssembling top rails ttach top rails 7 to upper rails & as shown and fix through holes using bolts. Fasten bolts using allen key F but do not fully tighten at this stage. 7 7 7
ssembly Instructions Step 7 9 ttaching slats Insert each slats 9 into holes on side rails. Lock it into position by pushing firmly down with your hand. Note: Make sure the slat is aligned to the hole before pushing it firmly down. fter all slats are positioned, tighten all bolts & nuts fixed in previous steps using allen keys F. 9 x2 Step 8 ttaching mattress stoppers Insert the mattress stoppers E into holes on the side rails as shown. ssembly is complete. If you need help or have damaged or missing parts, call the ustomer Helpline: rgos = 0 0 0800 7 E