Owner s Manual ompano 0 ft. x 2 ft. Mural Sun Shelter Sojag code: 999-350759 UC code: 77283050759 Date of purchase: / /
Table of Contents Safety Information...2 Warranty...3 What is Covered...3 What is Not Covered...3 Operation...3 Maintenance...3 Care and Cleaning...3 re-assembly...4 lanning Assembly...4 Tools Required...4 Hardware Included...5 ackage Contents...6 Assembly... 7-27 Safety Information WARNING: KEE ALL FLAME AND HEAT SOURCES AWAY FROM THIS TENT FABRIC. This tent meets the flammability requirements of CAI-84. The fabric may burn if left in continuous contact with any flame source. The application of any foreign substance to the tent fabric may render the flame-resistant properties ineffective. It is very important to read and follow the safety precautions before assembly and during the use of the product.. Keep all children and pets away from assembly area. 2. When assembling and using this product, basic safety precautions must always be followed to reduce risk of personal injury and damage to product or surroundings. 3. Ensure that all the parts are in the box before starting the assembly. Some parts may contain sharp edges, wear protective gloves. 4. This unit will take at least 5 hours to set up. You must schedule enough time to complete the assembly. You cannot leave it unattended if not fully assembled, even if bolted to the ground. At least 3 people are required for safe assembly. 5. Always install your unit on a level platform. The unit must be anchored to either wood or concrete using the appropriate screws for that flooring. 6. Check all screws for tightness before and during usage. 7. Your shelter has been created for all four seasons and will resist to snow accumulations of 2000 lbs. However, you must remove any snow accumulation on the roof. The mosquito nets and optional curtains must also be removed for winter storage. 8. Do not place any type of heat conductor under the sun shelter or within 5 feet of the unit including but not limited to a barbeque or space heater. 2
Warranty WHAT IS COERED The ompano is guaranteed against defective materials based on normal use of the product for year. Limited warranty applicable on parts only. WHAT IS NOT COERED Damages due to vandalism, abuse or wrong use of the product. Damages due to extreme weather conditions such as a thunderstorm, windstorm and hailstorm. Rust, water infiltration, holes in polycarbonate roof panels, fabric and structure discoloration are not covered under warranty. Operation The unit is a 4 season sun shelter, meaning it may be left up year round. However, any accumulation of snow must be removed from the roof of the unit at all times. Mosquito netting and optional curtains must be removed for storage during the winter. The unit must be anchored using the appropriate screws based on the flooring which it is be anchored to. Roof panels must be installed with the U protected side facing the sun. Failure to follow any of the previously mentioned requirements will void the warranty. Maintenance If this shelter needs repairs: In case of a defective part or if a problem occurs while using the product, please contact your retailer. To order replacement parts, use the part number on the parts list and the model number of your shelter. Care and Cleaning For cleaning: Use a domestic soap or detergent and wash with warm water using a sponge or fabric. Rinse with clean water. Check all screws on a regular basis to maintain the solidity of the structure. 3
re-assembly IMORTANT: Do not remove the protective film on the polycarbonate roof panels before installation (step 0, 6 & 7). Ensure to put the U protected side facing the sun. It is a very important procedure; if not followed as described, your roof will not be covered by the warranty. LANNING ASSEMBLY It is the consumer s responsibility to comply with any building codes, ordinances, zoning limitations, or local homeowner s restrictions and obtain any required permit, before purchase and installation of the products. Ensure that all the parts are in the box before starting the assembly. Some parts may contain sharp edges, wear protective gloves. This unit will take at least 5 hours to set up. You must schedule enough time to complete the assembly. You cannot leave the sun shelter unattended if not fully assembled, even if bolted to the ground. At least 3 people are recommended for assembling the unit. Follow all instructions to assure the strength of the shelter. In order to avoid damage to the shelter and its components, use appropriate tools. Do not use the structure as a support; a stepladder is recommended. Keep instructions and parts list for further reference. TOOLS REQUIRED Not included in the box. Safety GoGgles Safety Hat hillips Screw Driver Gloves Stepladder level 4
HArdware Kit NOTE: arts not shown to actual size and not to scale. N N X4 O 2 X6 Q Q Q2 X4 Item Description Qty U X4 06 N Base 2 N Anchoring Support 4 N2 Base 2 O Iron angle 2 Iron angle 2 W X6 X X32 Iron angle 6 Q Finishing End Q Finishing End Y 2 Y 2 Q2 Finishing End 4 U Screw & Nut M60 4 Screw M66 06 W Screw M60 6 Z X Screw M65 32 Y Nut 2 N2 Y Nut 2 Z Allen Key Z Z Wrench 5
Arts List Item Description NOTE: arts not shown to actual size and not to scale. A D2 A B F2 B2 X4 B3 C G3 K 0 C D Ka D F K2a F G G G2 H Kb X4 K2b H I I I2 L J J 6 M R X38 J2 X4 M X5 S X4 Qty A Column A Column B Column 2 B2 Winter Solidifying Column B3 Winter Solidifying Column C Track C Track D Track D Track D2 Junction Bar F Structure Bar F Structure Bar F2 Junction Bar 4 G Structure Bar G Structure Bar G2 Solidifying Bar 4 G3 Junction Bar 2 H Roof Finishing Bar (back) H Roof Finishing Bar (back) I Roof Finishing Bar (front) I Roof Finishing Bar (front) I2 Roof Finishing Bar (back) J Roof Bar (corner) J Roof Bar (corner) J2 Roof Bar (middle) 4 K Roof anel 0 Ka Roof anel K2a Roof anel Kb Roof anel K2b Roof anel L Roof Support Bar 5 M Side Finishing End M Side Finishing End R Hook 38 S Mosquito Netting 4
NOTE: Ensure that the rim of Bases (N) faces the front of the columns as illustrated. Step. Install the Anchoring Supports (N) on the Column (A) and the Column (A) using the Screws (U)..2 Install the Column (A) and the Column (A) on the Bases (N) using the Screws ()..3 Install the Columns (B) on the Bases (N2) using the Screws (). A N N A N U N U A A N B N N B A B N2 N N2 N2 N N2 A 6 N X4 U X4 A B 7
NOTE: Ensure the ends of the hooks are facing away from the tracks. NOTE: The sun shelter has double tracks for use of mosquito nettings and curtains. The curtains and extra hooks are sold separately while quantity last. Hooks for curtains will be placed into the track closest to the ogee following the same quantity used for the mosquito nettings. Step 2 2. Insert 2 Hooks (R) into the Track (C) and 2 Hooks (R) into the Track (C) by sliding them into the outer track. 2. Insert 7 Hooks (R) into the Track (D) and 7 Hooks (R) into the Track (D) by sliding them into the outer track. C & C C & C R 2 D & D D & D R X7 R X38 D D C C 8
Step 3 3. Insert the junction bar (D2) half way into the track (D) and insert the screws (). 3.2 Insert the other half of the junction bar (D2) into the track (D) and insert the screws (). Ensure that the screws are tightened. D D2 D D D D D X8 D D2 D 9
Step 4 4. Insert two Junction Bars (F2) half way into the track (F) and insert the Screws (). 4.2 Insert the other halves of the Junction Bars (F2) into the Track (F) and insert the Screws (). Ensure that the screws are tightened. F2 F F2 F F F X8 F F2 F 0
Step 5 5. Insert two Junction Bars (F2) half way into the Track (G) and insert the Screws (). 5.2 Insert the other halves of the Junction Bars (F2) into the Track (G) and insert the Screws (). Ensure that the screws are tightened. F2 G F2 G G G X8 G F2 G
Step 6 6. Insert the Junction Bar (G3) half way into the Solidifying Bars (G2) and insert Screws (). 6.2 Insert the other half of the Junction Bar (G3) into the Solidifying Bars (G2) and insert Screws (). Ensure that the screws are tightened. Repeat twice. G2 G3 G2 G2 G2 X8 G3 G2 X4 2
Step 7 7. Install the complete Track (D & D) between two (2) Columns (B) using the Screws (X). 7.2 Install the complete structure Bar (F & F) between the Columns (A & A) using the Screws (X). 7.3 Install the Track (C) between the Columns (A & B) and the Track (C) between the Columns (A & B) using the Screws (X) so that the tracks are facing the inside of the shelter. F X F C A C D D A X B B X X X X32 C C 3
Step 8 8. Install an Iron Angle (O) on the Tracks (C) using the Screws (). 8.2 Install an Iron Angle (O) on the Tracks (C) using the Screws (). 8.3 Install the Structure Bars (G & G) onto the Iron Angles (O) using the Screws (). O O C G C O G O X6 4
NOTE: The longer pre-inserted screws found on the Roof Bar (J) and the Roof Bar (J) will be used in step 4. Step 9 9. Install the Iron Angles () on each end of the Structure Bars (D & D), (F & F) and (G & G) using the Screws (). 9.2 Install the Roof Bars (J & J) by inserting the 2 pre-installed screws found at their centers into the pre-drilled holes in the Iron Angles () installed on the Structure Bars (G & G). Secure with the Nuts (Y). 9.3 Secure the ends of the Roof Bars (J & J) with the Screws () through the pre-drilled holes on the top of the Iron Angles (). J F F J G G D D Y 0 Y J X6 J 5
CAUTION: One side of the roof panels is U protected. Ensure to put the U protected side facing the outside of the shelter. It is a very important procedure; if not followed as described, your roof will not be covered by the warranty. NOTE: The roof panels are covered with a plastic film identifying which side has a U protector. Once the plastic film is removed it is impossible to know which side has the U protector. We recommend removing the film one at a time just prior to installing the roof panel. Step 0 0. Insert the Roof anel (Ka) and the Roof anel (Kb) into the end of the Tracks. 0.2 Insert the Roof anel (K2a) and the Roof anel (K2b) behind previously inserted roof panels until they are flush. K2b J Kb K2a J Ka J Ka K2a Ka Kb K2b 6
Step. Screw the Iron Angles () on the Structure Bars (D, D, F, F, G & G) using the Screws (). D G D G F F 2 2 4 7
NOTE: The longer pre-inserted screws will be used to install solidifying bars in step 3. Step 2 2. Install the Roof Bars (J2) by aligning the pre-inserted short screws found at their centers with the pre-drilled holes in the Iron Angles () on the Stucture Bars (G & G) and secure with the Nuts (Y). 2.2 Secure the ends of the Roof Bars (J2) to the bars (D, D, F and F) with the Screws () through the pre-drilled holes in the Iron angles (). Y J2 J2 J2 J2 D X4 D G G F F X8 X8 Y X4 J2 X4 8
NOTE: Ensure that the solidifying bars are well centered before tightening the Nuts (Y). Step 3 3. Install the Solidifying Bars (G2) using the longer pre-inserted screws found along the Roof Bars (J2) and securing them with the Nuts (Y). G2 G2 G2 G2 G2 G2 Y 2 2 Y 2 9
Step 4 4. Install the Roof Finishing Bar (H) and the Roof Finishing Bar (H) using the Screws (). X4 H H H X6 H 20
Step 5 5. Install the Side Finishing End (M) and the Side Finishing End (M) using the Screws (). M M M or M M M X4 2
CAUTION: One side of the roof panels is U protected. Ensure to put the U protected side facing up towards the sun. It is a very important procedure; if not followed as described, your roof will not be covered by the warranty. NOTE: The roof panels are covered with a plastic film identifying which side has a U protector. Once the plastic film is removed it is impossible to know which side has the U protector. We recommend removing the film one at a time just prior to installing the roof panel. Step 6 6. Slide one row of the Roof anels (K) to upper tracks of the Roof Bars. Repeat 5 times. K K K K K K This side up X5 K X5 22
Step 7 7. Slide the Roof Support Bars (L) into the lower tracks of the Roof Bars until flush with the Roof anels (K). 7.2 Slide the remaining anels (K) into lower tracks of the Roof Bars until flush with the Roof Support Bars (L). L L L L L K L This side up X5 K X5 L X5 K X5 23
Step 8 NOTE: 2 people are required for this step. 8. From the left side of the shelter, insert a Screw (W) at the end of the first three Roof Bars (J, J2 & J2). Install the Roof Finishing Bar (I) by inserting the pre-inserted Screws (W) found on the Roof Bars into the pre-drilled holes. lace a Finishing End (Q) over the first Screw (W) and secure with Nut (Y). lace a Finishing End (Q2) over the next screw and secure with Nut (Y). A Finishing End (Q2) will be installed at the end of the second Roof Bar (J2) in step 8.3. 8.2 From the right side of the shelter, insert a Screw (W) at the end of each Roof Bar (J, J2 & J2). Install the Roof Finishing Bar (I), using the same process as described in 8.. lace a Finishing End (Q) over the last Screw (W) and secure with Nut (Y). lace a Finishing End (Q2) over the next Screw (W) and secure with Nut (Y). A Finishing End (Q2) will be installed at the end of the second to last Roof Bar (J2) in step 8.3. 8.3 Install the Roof Finishing Bar (I2) in the center of the unit, over the 2 remaining Screws (W). lace 2 Finishing Ends (Q2) over the Screws (W) and secure with Nuts (Y). J W Q I Y J Draw X4 W J2 W J W W J I Q Q2 I Q2 W I2 Q2 J2 I Q2 Q Q Y Y Q2 X4 Q Y X6 I I Q Q2 X4 W X6 I2 24
Note: The 2 shorter panels of the Mosquito Netting (S) are installed next to the posts which are closest to the home. When installing long panel, ensure the corner of the mosquito net matches with Columns (B). Step 9 NOTE: For optional curtains, install the curtains first on the track closest to the ogee than install the mosquito netting on the track closest to the inside of the shelter. 9. Install the Mosquito Netting (S) on inner track s Hooks (R). Wrap elcro band on the Mosquito Netting (S) around columns (B). S S B S R S B S X4 25
Note: On this picture we have removed to roof panels in order to show you where the Winter Solidifying Columns (B2 & B3) go. Step 20 This next step is only to be done for the winter season. 20. Install the Winter Solidifying Column (B2) and the Winter Solidifying Column (B3) under the respective cross beams (the second and fourth crossbeans) before the winter season in order to solidify the roof due to heavy snow. B3 B2 B2 B3 26
Note 27
rinted in China Made in CHINA