Installation, Maintenance & Parts Manual

Installation, Maintenance & Parts Manual 00 Series End Drive Conveyors Table of Contents Warnings General Safety........................... Introduction....................................... Product Description................................. Specifications...................................... Installation........................................ RequiredTools................................... Recommended Installation Sequence................. 5 Conveyors Up to ft (96 mm)................... 5 Conveyors Longer Than ft (96 mm)............. 5 Mounting Brackets............................... 6 Return Rollers................................... 7 Cleated Belt and 6 (5 5 mm) Wide Flat Belt Conveyors............................ 7 8 (0 60 mm) Wide Flat Belt Conveyors............................ 7 Preventative Maintenance & Adjustment................ 8 Required Tools................................... 8 Standard Tools................................ 8 Special Tools.................................. 8 Checklist....................................... 8 Lubrication..................................... 8 Maintaining Conveyor Belt......................... 8 Troubleshooting............................... 8 Cleaning..................................... 8 Conveyor Belt Replacement........................ 8 Conveyor Belt Replacement Sequence.............. 8 Belt Removal for Conveyor Without Stands or Gearmotor Mounting Package.............. 9 Belt Removal for Conveyor With Stands and Gearmotor Mounting Package............. 9 Belt Installation for Conveyor Without Stands or Gearmotor Mounting Package............. 0 Belt Installation for Conveyor With Stands and Gearmotor Mounting Package............ 0 Conveyor Belt Tensioning......................... Conveyors with.5 ( mm) Diameter Pulleys.... Conveyors with Nose Bar Idlers.................. Conveyor Belt Tracking.......................... Pulley Removal................................. A Idler Pulley Removal....................... A Idler Pulley Removal....................... B Drive Pulley Removal...................... Bearing Removal & Replacement................... Pulley Replacement.............................. 5 Drive Pulley................................. 5 Idler Pulley.................................. 6 Nose Bar Bearing Replacement.................... 7 Service Parts..................................... 9 (5mm) Conveyor Assembly.................... 9 (76mm) to 6 (5mm) Conveyor Assembly........ 8 (0mm) to (605mm) Conveyor Assembly...... 8 (57mm) to (60mm) Conveyor Assembly..... Nosebar End Assembly (5mm) to (60mm).... 6 0 (76mm) Aluminum Side.................... 7 05.5 (8mm) Aluminum Side.................. 8 07 Low to Side Wiper........................... 9 09 Low to High Side........................... 0 0.5 (mm) Extruded Plastic................... Adjustable Guiding...........................5 (mm) Cleated Guiding....................... (5mm) Cleated Guiding....................... (5mm) Cleated Guiding....................... 5 Flared Side Guiding............................. 6 Flat Belt Mounting Bracket........................ 7 Cleated Belt Mounting Bracket..................... 7 Flat Belt Mounting Brackets for (60mm) Conveyors..................................... 8 Cleated Belt Mounting Brackets for (60mm) Conveyors..................................... 8 Connecting Assembly without Stand Mount.......... 9 Flat Belt Connecting Assembly without Stand Mount................................... 9 Cleated Belt Connecting Assembly without Stand Mount................................... 0 (5mm) to 6 (5mm) Flat Belt Return Roller...... 0 8 (0mm) to (60mm) Flat Belt Return Roller.... Cleated Belt Return Roller........................ Conveyor Belt Part Number Configuration........... Return Policy..................................... 85-5 Rev. B

Warnings General Safety The safety alert symbol, black triangle with white exclamation, is used to alert you to potential personal injury hazards. Gearmotors may be HOT. DO NOT TOUCH Gearmotors. Climbing, sitting, walking or riding on conveyor will cause severe injury. KEEP OFF CONVEYORS. DO NOT OPERATE CONVEYORS IN AN EXPLOSIVE ENVIRONMENT. Dorner cannot control the physical installation and application of conveyors. Taking protective measures is the responsibility of the user. When conveyors are used in conjunction with other equipment or as part of a multiple conveyor system, CHECK FOR POTENTIAL PINCH POINTS and other mechanical hazards before system start-up. Exposed moving parts can cause severe injury. LOCK OUT POWER before removing guards or performing maintenance. Loosening stand height or angle adjustment screws may cause conveyor sections to drop down, causing severe injury. SUPPORT CONVEYOR SECTIONS PRIOR TO LOOSENING STAND HEIGHT OR ANGLE ADJUSTMENT SCREWS. Introduction IMPORTANT: Some illustrations may show guards removed. DO NOT operate equipment without guards. Upon receipt of shipment: Compare shipment with packing slip. Contact factory regarding discrepancies. Inspect packages for shipping damage. Contact carrier regarding damage. Accessories may be shipped loose. See accessory instructions for installation. Dorner s Limited Warranty applies. Dorner 00 series conveyors are covered by Patent No. 5,7,5 and corresponding patents and patent applications in other countries. Dorner reserves the right to make changes at any time without notice or obligation. 85-5 Rev. B Dorner Mfg. Corp.

Product Description Refer to Figure for typical conveyor components. Typical Components A Conveyor B Gearmotor Mounting Package C Gearmotor D Guiding & Accessories E Mounting Brackets F Return Rollers G Support Stand H Variable Speed Controller I Drive End J Idler/Tension End B C D I A F E E H G J Figure Specifications Models: Flat Belt 00 Series Conveyor 0 M WW LLLL A PP BB Belt Type* Conveyor Profile* Output Shaft Position* Conveyor Length Reference Conveyor Width Reference Document Language, M = English = Flat belt with tracking cams (non V-guided belt) = Flat belt with V-guide tracking = Nose bar transfer at tension end (non V-guided belt) Cleated Belt 00 Series Conveyor C M WW LLLL A SSSS Cleat Spacing* Output Shaft Position* Conveyor Length Reference Conveyor Width Reference Document Language, M = English Cleat Type* = Cleated belt with V-guide tracking 5 = Cleated belt with tracking cams (non V-guided belt) * See Ordering and Specifications Catalog for details. Conveyor Supports: Maximum Distances: K = 8 (57 mm)** L = 6 ft (89 mm)*** M = 8 (57 mm) K L M ** For Heavy Load Bottom Mount Package, mount support under gear head. *** For conveyors longer than ft (96 mm), install support at joint. Figure Dorner Mfg. Corp. 85-5 Rev. B

Specifications Specifications: Conveyor Width Reference (WW) 0 0 0 05 06 08 0 8 Conveyor Belt Width.75 (mm).75 (70mm).75 (95mm) 5 (7mm) 6 (5mm) 8 (0mm) 0 (5mm) (05mm) 8 (57mm) (5mm) (609mm) Maximum Conveyor Load* (See NOTE Below) 0 lb (kg) 5 lb (6kg) lb (9kg) 50 lb (kg) 60 lb (7kg) 70 lb (kg) 80 lb (6kg) 80 lb (6kg) 80 lb (6kg) 80 lb (6kg) 80 lb (6kg) Conveyor Startup Torque* in-lb (0.5Nm) in-lb (0.6Nm) in-lb (0.7Nm) 6 in-lb (0.8Nm) 8 in-lb (0.9Nm) 0 in-lb (.Nm) in-lb (.Nm) in-lb (.Nm) in-lb (.Nm) in-lb (.Nm) in-lb (.Nm) Belt Travel.0 (88 mm) per revolution of pulley Maximum Belt Speed* 6 ft/minute (80.5 m/minute) Belt Takeup 0.8 (0 mm) of stroke = 0.75 (9 mm) of belt take-up Conveyor Length Reference (LL) Conveyor Length Up to 8 ft in any length to nearest 0. (mm) 0 0 0 05 06 07 08 09 0 ** ** 5** 6** 7** 8** 8-ft (586 mm)** 7-ft (58 mm)** 6-ft (877 mm)** 5-ft (57 mm)** -ft (67 mm)** -ft (96 mm)** -ft (658 mm) -ft (5 mm) 0-ft (08 mm) 9-ft (7 mm) 8-ft (8 mm) 7-ft ( mm) 6-ft (89 mm) 5-ft (5 mm) -ft (9 mm) -ft (9 mm) -ft (60 mm) NOTE: Maximum conveyor loads based on: Non-accumulating product Product moving towards gearmotor Conveyor being mounted horizontal * See Ordering and Specifications Catalog for details. ** Lengths available only in 6 (5 mm) & wider conveyors. Installation NOTE: Conveyor MUST be mounted straight, flat and level within confines of conveyor. Use a level (N of Figure ) for setup. O P Q Installation Component List Conveyor frame (two sections if longer than ft) Conveyor brackets (x) Return rollers (for longer conveyors) N Required Tools Hex-key wrenches: mm, 5 mm Level Torque wrench Figure 85-5 Rev. B Dorner Mfg. Corp.

Installation Recommended Installation Sequence Install support stands (see accessory instructions) Assemble conveyor (if required) Attach mounting brackets to conveyor Attach conveyor to stands Install return rollers on conveyor (optional) Mount gearmotor mounting package (see accessory instructions) O O Attach guides/accessories (see page 7 through 5 of Service Parts section for details) Figure 6 Conveyors Up to ft (96 mm) No assembly is required. Install mounting brackets and return rollers. Refer to Mounting Brackets on page 6 and Return Rollers on page 7.. Join conveyor sections and install connector brackets (V of Figure 7) or connector/mount brackets (VA) and screws (W) on both sides as indicated. Tighten screws to 60 in-lb (7 Nm). V Conveyors Longer Than ft (96 mm). Locate conveyor sections (O Figure ) W W O VA Figure 7 Figure. On tension end of the conveyor, identified with a label (R of Figure 5), push in head plate assembly (S): On both sides of conveyor, loosen and move cam tracking assemblies (T) (if equipped) away from head plates, then loosen fastening screws (U) and push head plate assembly inward. O 5. With a 5 mm hex-key wrench, rotate pinion gear (X of Figure 8) to tension the conveyor belt. Tighten fastening screws (U) on both sides of conveyor to 80 in-lb (9 Nm). For proper tensioning, refer to Conveyor Belt Tensioning on page. U U T X Figure 8 S Figure 5. Roll out conveyor belt and place conveyor frame sections (O of Figure 6) into belt loop. R 6. Install mounting brackets and return rollers. Refer to Mounting Brackets on page 6 and Return Roller on page 7. 7. If equipped with cam tracking assemblies (T of Figure 5), reposition and adjust belt tracking. Refer to Conveyor Belt Tracking on page. Dorner Mfg. Corp. 5 85-5 Rev. B

Installation Mounting Brackets. Locate brackets. Exploded views shown in Figures 9 & 0. Y AC. Remove screws (Y & Z of Figures 9 & 0), washers (AA), nuts (AB) and T-bars (AC) from brackets.. Insert T-bars (AC of Figures 9 & 0) into conveyor side slots (AD of Figure ). Fasten brackets (P of Figure ) to conveyor with mounting screws (Y). AD AB Y AA Z AA AB P Z Mounting Brackets for Flat Belt Conveyor Figure 9 Figure Y AC NOTE: Mounting brackets for flat belt conveyors shown. AA AB. Fasten brackets to support stand with mounting screws (Z of Figure ), washers (AA) and nuts (AB). 5. Tighten screws (Y & Z of Figure ) to 60 in-lb (7 Nm). Z Mounting Brackets for Cleated Belt Conveyor Figure 0 85-5 Rev. B 6 Dorner Mfg. Corp.

Installation Return Rollers Cleated Belt and 6 (5 5 mm) Wide Flat Belt Conveyors. Locate return rollers. Exploded views shown in Figures &. AF AE 8 (0 60 mm) Wide Flat Belt Conveyors. Locate return rollers. Exploded view shown in Figure 5. AH AG AE AF Return Rollers for Flat Belt Conveyor Figure AF AE AG AH Figure 5. Remove screws (AG of Figure 5) and clips (AH) from roller assembly.. Install roller assembly as shown (Q of Figure 6). Tighten screws (AG) to 60 in-lb (7 Nm). Q AE AF AG Return Rollers for Cleated Belt Conveyor Figure. Remove screws (AE of Figures & ) and clips (AF) from roller assembly.. Install roller assemblies (Q of Figure ) as shown. Tighten screws (AE) to 60 in-lb (7 Nm). Figure 6 AE Q Q Figure Dorner Mfg. Corp. 7 85-5 Rev. B

Preventive Maintenance and Adjustment Required Tools Standard Tools Hex-key wrenches:.5 mm, mm, 5 mm Arbor press Special Tools 807 078 Sealed Bearing Removal Tool 509 Sealed Bearing Installation Tool Checklist Keep service parts on hand (see Service Parts section for recommendations) Keep supply of belt cleaner (part # 6569) Clean entire conveyor and knurled pulley while disassembled Replace worn or damaged parts Lubrication No lubrication is required. Replace bearings if worn. Maintaining Conveyor Belt Troubleshooting Inspect conveyor belt for: Surface cuts or wear Stalling or slipping Damage to V-guide Surface cuts and wear indicate: Sharp or heavy parts impacting belt Jammed parts Improperly installed bottom wipers (if installed) Accumulated dirt in wipers (if installed) Foreign material inside the conveyor Improperly positioned accessories Bolt-on guiding is pinching belt Stalling or slipping indicates: Excessive load on belt Conveyor belt or drive timing belt are not properly tensioned Worn knurl or impacted dirt on drive pulley Intermittent jamming or drive train problems Damage to V-guide indicates: Twisted or damaged conveyor frame Dirt impacted on pulleys Excessive or improper side loading NOTE: Visit www.dorner.com for complete list of troubleshooting solutions. Cleaning IMPORTANT: Do not use belt cleaners that contain alcohol, acetone, Methyl Ethyl Ketone (MEK) or other harsh chemicals. Use Dorner Belt Cleaner (part # 6569). Mild soap and water may also be used. Do not soak the belt. For /05 woven polyester and /06 black anti-static belts, use a bristled brush to improve cleaning. Conveyor Belt Replacement Exposed moving parts can cause severe injury. LOCK OUT POWER before removing guards or performing maintenance. Conveyor Belt Replacement Sequence Remove old conveyor belt: -Conveyor without Stands or Gearmotor Mounting Package -Conveyor with Stands and Gearmotor Mounting Package Install new conveyor belt Tension conveyor belt 85-5 Rev. B 8 Dorner Mfg. Corp.

Preventive Maintenance and Adjustment Belt Removal for Conveyor Without Stands or Gearmotor Mounting Package. If equipped, remove bottom wipers (AJ of Figure 7): Remove fastening screws (AI) then remove wiper (AJ).. Place temporary support stands (AK of Figure 9) at both ends of the conveyor. Place an additional support stand under the drive motor (AL), if equipped. See WARNING. AI AI AM AJ AL AK Figure 9 AK AM Figure 7. If equipped, remove return rollers and guiding and accessories from one side of conveyor.. On tension end of the conveyor, identified with a label (R of Figure 8), push in head plate assembly (S): On both sides of conveyor, loosen and move cam tracking assemblies (T) (if equipped) away from head plates, then loosen fastening screws (U) and push head plate assembly inward. U T. Remove mounting brackets (AM of Figure 9) from one side of conveyor. (Reverse steps & of Mounting Brackets section on page 6.) If equipped with heavy load drive package, remove brackets from side opposite drive cover (AN of Figure 0).. If equipped, remove bottom wipers (AJ of Figure 7): Remove fastening screws (AI) then remove wiper (AJ).. If equipped, remove return rollers, guiding and accessories from side opposite drive cover (AN of Figure 0). S Figure 8 R AN AO. Remove conveyor belt. Belt Removal for Conveyor With Stands and Gearmotor Mounting Package AP Ç Removing mounting brackets without support under gearmotor will cause conveyor to tip, causing severe injury. PROVIDE SUPPORT UNDER- NEATH THE GEARMOTOR WHEN CHANGING THE BELT Figure 0 AO 5. If equipped with heavy load drive package, remove drive support bracket (AP of Figure 0): Remove bracket screws (AO) then remove bracket (AP). Dorner Mfg. Corp. 9 85-5 Rev. B

Preventive Maintenance and Adjustment 6. On tension end of the conveyor, identified with a label (R of Figure ), push in head plate assembly (S): On both sides of conveyor, loosen and move cam tracking assemblies (T) (if equipped) away from head plates, then loosen fastening screws (U) and push head plate assembly inward. S U Figure 7. Remove belt (AQ of Figure ) from conveyor. AQ T R AQ Belt Installation for Conveyor with Stands and Gearmotor Mounting Package Removing mounting brackets without support under gearmotor will cause conveyor to tip, causing severe injury. PROVIDE SUPPORT UNDER- NEATH THE GEARMOTOR WHEN CHANGING THE BELT. Ensure temporary support stands (AK of Figure 9) are placed at both ends of the conveyor. Place an additional support stand under the drive motor (AL), if equipped. See WARNING.. Orient belt so splice leading fingers (AR of Figure ) point in the direction of belt travel as identified by the conveyor directional label (AS).. Install belt (AQ of Figure ) on conveyor. Lift conveyor slightly to avoid pinching belt on temporary support stands. Figure Belt Installation for Conveyor without Stands or Gearmotor Mounting Package. Orient belt so splice leading fingers (AR of Figure ) point in the direction of belt travel as identified by the conveyor directional label (AS). AR AS AQ Figure AQ. Re-install conveyor mounting brackets. Refer Mounting Brackets on page 6, steps through 5. 5. If equipped with a heavy load drive package, re-install drive support bracket (AP of Figure 0). 6. Tension belt. Refer to Conveyor Belt Tensioning on page. 7. If equipped, re-install wipers, return rollers and guiding. Figure. Slide belt onto the conveyor frame assembly.. Tension belt. Refer to Conveyor Belt Tensioning on page.. If equipped, install wipers, return rollers and guiding. 85-5 Rev. B 0 Dorner Mfg. Corp.

Preventive Maintenance and Adjustment Conveyor Belt Tensioning the end of the conveyor frame with or between the tensioning marks. See NOTE. Exposed moving parts can cause severe injury. LOCK OUT POWER before removing guards or performing maintenance. AT AU Conveyors with.5 ( mm) Diameter Pulleys. On tension end of the conveyor, identified with a label (R of Figure 5), adjust head plate assembly (S): On both sides of conveyor, loosen fastening screws (U) and rotate pinion gear (X) to adjust head plate assembly. U T Figure 6 NOTE: On pinion gear, do not exceed a torque of 5 in-lb (.8 Nm) for ( 05mm) wide conveyors and 50 in-lb (.5 Nm) for an 8 (57 60mm) wide conveyor. Over tensioning the conveyor belt could cause excessive pulley bearing load and early failure. S Figure 5. Adjust head plate assembly so end of conveyor frame aligns with or between the head plate tensioning marks (AT & AU of Figure 6). Replace belt if proper tensioning can not be obtained while aligning R X. After adjusting proper tensioning, tighten fastening screws (U of Figure 5) on both sides of conveyor to 60 in-lb (7 Nm).. If equipped with cam tracking assemblies (T of Figure 5), position against head plates and adjust belt tracking. Refer to Conveyor Belt Tracking on page. Dorner Mfg. Corp. 85-5 Rev. B

Preventive Maintenance and Adjustment Conveyors with Nose Bar Idlers. On tension end of the conveyor, identified with a label (R of Figure 7), adjust head plate assembly (S): On both sides of conveyor, loosen fastening screws (U) and rotate pinion gear (X) to adjust head plate assembly. U T Conveyor Belt Tracking V-Guided Belts V-guided belts do not require tracking adjustment. Non V-Guided Belts Non V-guided belt conveyors are equipped with belt tracking cam assemblies (T of Figure 9) for belt tracking adjustment. BELT TRAVEL U T S R X Figure 7. Adjust head plate assembly so the edge of the axle support plate (AV of Figure 8) is separated from the end of the conveyor (AW) by.5 (9 mm). Replace belt if proper tensioning can not be obtained within a distance of.50 (8 mm). See NOTE. S AY AZ AX Figure 9 AV AW.5 (9 mm) When adjusting belt tracking, always adjust the discharge end of the conveyor first. To adjust belt tracking:. Ensure head plate fastening screws (U of Figure 9) on both sides of conveyor are tightened. Figure 8 NOTE: On pinion gear, do not exceed a torque of 5 in-lb (.8 Nm) for ( 05mm) wide conveyors and 50 in-lb (.5 Nm) for an 8 (57 60mm) wide conveyor. Over tensioning the conveyor belt could cause excessive pulley bearing load and early failure.. After adjusting proper tensioning, tighten fastening screws (U of Figure 7) on both sides of conveyor to 60 in-lb (7 Nm).. If equipped with cam tracking assemblies (T of Figure 7) position against head plates and adjust belt tracking. Refer to Conveyor Belt Tracking, next section.. On both sides of conveyor, loosen two () cam fastening screws (AX). Adjust cams (AY) until indicator slots (AZ) are horizontal and facing end of conveyor. Then slide cam assemblies against head plates (S) and re-tighten cam fastening screws (AX) to 60 in-lb (7 Nm).. On the side toward which the belt is tracking, loosen head plate fastening screws (U).. With the conveyor running, use a 5 mm hex-key wrench to rotate the tracking cam (AY) in small increments until the belt tracks in the center of the conveyor. Then while holding the cam in position, re-tighten the head plate fastening screws (U) with a mm hex-key wrench to 60 in-lb (7 Nm). 85-5 Rev. B Dorner Mfg. Corp.

Preventive Maintenance and Adjustment Pulley Removal Exposed moving parts can cause severe injury. LOCK OUT POWER before removing guards or performing maintenance. Remove conveyor belt to access pulley(s). See Conveyor Belt Replacement on page 8. Remove the desired pulley following the corresponding instructions below: A Idler Pulley Removal B Drive Pulley Removal A Idler Pulley Removal. On both sides of conveyor, loosen two () fastening screws (U of Figure 0). Then slide idler pulley assembly out from the conveyor frame.. With mm hex-key wrench, loosen pulley taper screw (BB of Figure ). Steady pulley with second hex-key wrench (BC) inserted into pulley hole. Repeat procedure for opposite side of pulley. BB Figure BC. Pull head plates with bearings off from the pulley. B Drive Pulley Removal Drive shaft keyway may be sharp. HANDLE WITH CARE. U Figure 0. Remove bearing covers (BA of Figure ).. On both sides of conveyor, loosen two () fastening screws (U of Figure ). Then slide drive pulley assembly out from the conveyor frame. BA U Figure Figure Dorner Mfg. Corp. 85-5 Rev. B

Preventive Maintenance and Adjustment. Remove bearing cover (BA of Figure ) from side opposite of drive shaft. Bearing Removal & Replacement Removal. Turn bearing (BF of Figure 7) to align with slots (BG) in head plate. Then remove bearing. BG BF BA Figure. On side opposite of drive shaft, loosen pulley taper screw (BB of Figure 5) with mm hex-key wrench. Steady pulley with second hex-key wrench (BC) inserted into pulley hole. BC Figure 7 Replacement. Inspect head plate bearing surface. If worn or damaged, replace head plate. See Service Parts on page 9.. Insert bearing (BF of Figure 8) into head plate slot and twist bearing to fit into bearing enclosure. BB BF Figure 5. On side opposite of drive shaft, pull head plate with bearings off from the pulley. 5. With bearing removal tool, (BD of Figure 6), part number 807 078, remove head plate from drive shaft side of pulley. Connect tool jaws at indicated points (BE). BD Figure 8 BE Figure 6 BE 85-5 Rev. B Dorner Mfg. Corp.

Preventive Maintenance and Adjustment Pulley Replacement Drive Pulley. With bearing installed in head plate, use a bearing installation tool, (BH of Figure 9), part number 509, to press the bearing onto the drive shaft. BH U Figure. With mm hex-key wrench, tighten pulley taper screw (BB of Figure ) to 5 in-lb ( Nm). Steady pulley with second hex-key wrench (BC) inserted into pulley hole. Figure 9. With bearing installed in head plate, press bearing on to non-drive shaft (BI of Figure 0) of pulley. BC BB Figure 5. Install bearing covers (BA of Figure ). BI Figure 0 NOTE: DO NOT tighten non-drive shaft bearing taper screws at this time.. Install pulley assembly on conveyor. On both sides of conveyor tighten fastening screws (U of Figure ) to 60 in-lb (7 Nm). Figure BA Dorner Mfg. Corp. 5 85-5 Rev. B

Preventive Maintenance and Adjustment Idler Pulley. With bearing installed in head plate, press bearing on to shaft (BI of Figure ) of pulley. Repeat for both sides of pulley.. On both sides of pulley, use a mm hex-key wrench to tighten pulley taper screw (BB of Figure 6) to 5 in-lb ( Nm). Steady pulley with second hex-key wrench (BC) inserted into pulley hole. BC BI Figure NOTE: DO NOT tighten shaft bearing taper screws at this time. Figure 6 BB. Install bearing covers (BA of Figure 7).. Install pulley assembly on conveyor. On both sides of conveyor, hand tighten fastening screws (U of Figure 5). BA Figure 7 U Figure 5 85-5 Rev. B 6 Dorner Mfg. Corp.

Preventive Maintenance and Adjustment Nose Bar Bearing Replacement. On both sides of conveyor, use a mm hex-key wrench to loosen cam fastening screws (BJ of Figure 8) and slide cam assemblies toward the center of the conveyor. U. Slide bearing rods (BL of Figure 9) out side of conveyor and replace bearings (BM) as necessary. BL BM BK S Figure 8. On both sides of conveyor, use a mm hex-key wrench to loosen head plate fastening screws (U) to remove belt tension. Then remove belt from end of conveyor.. On one side of conveyor, use a mm and mm hex-key wrench to remove head plate fastening screws (BK & U) and remove head plate (S). BJ Figure 9 5. After replacing bearings, re-install head plate (S of Figure 8). Use a mm hex-key wrench to tighten one () fastening screw (BK) to 0 in-lb (. Nm). Leave two () fastening screws (U) loose for belt tensioning. 6. Re-install belt on end of conveyor, then tension the belt. See Conveyor Belt Tensioning on page. 7. Re-position the cam assemblies against the head plates and adjust belt tracking. See Conveyor Belt Tracking on page. Dorner Mfg. Corp. 7 85-5 Rev. B

NOTE: For replacement parts other than those shown on this page, contact an authorized Dorner Service Center or the factory. (5mm) Wide Conveyor Assembly 6 5 6 7 9 5 8 6 6 6 0 85-5 Rev. B 8 Dorner Mfg. Corp.

05 Head Plate LH 06 Head Plate RH 07 Bearing Cover Disk 08 Bearing 5 09 Tension Slide Bar 6 00 Taper Screw 7 00 Rack Gear.5 PA x P 8 0 Pinion Pin 9 0 Pinion (5mm) 0 060 Drive Spindle (5mm) 070 Idler Spindle (5mm) See Chart Below (5mm) Frame 506SSP Sleeve,.5 Magnet Stainless Steel 808 00 Magnet.5 Dia x.5 Long 5 9069M Socket Head Screw M6 x 0mm 6 9069M Socket Head Screw M6 x mm Item : (5mm) Conveyor Frame Length Part Number (60mm) 00 0908 (9mm) 00 008 (9mm) 00 008 5 (5mm) 00 05508 6 (89mm) 00 06708 7 (mm) 00 07908 8 (8mm) 00 0908 9 (7mm) 00 008 0 (08mm) 00 508 (5mm) 00 708 (658mm) 00 908 Dorner Mfg. Corp. 9 85-5 Rev. B

(76mm) to 6 (5mm) Wide Conveyor Assembly 0 8 5 8 6 8 5 7 5 8 8 7 6 9 85-5 Rev. B 0 Dorner Mfg. Corp.

05 Head Plate LH 06 Head Plate RH 07 Bearing Cover Disk 08 Bearing 5 09 Tension Slide Bar 6 00 Taper Screw 7 00 Rack Gear.5 PA x P 8 0 Pinion Bushing 9 060 Drive Spindle (76mm) 060 Drive Spindle (0mm) 0605 Drive Spindle 5 (7mm) 0606 Drive Spindle 6 (5mm) 0 070 Idler Spindle (76mm) 070 Idler Spindle (0mm) 0705 Idler Spindle 5 (7mm) 0706 Idler Spindle 6 (5mm) 000M Gear Pinion (76mm) 000M 0005M 0006M Gear Pinion (0mm) Gear Pinion 5 (7mm) Gear Pinion 6 (5mm) See Chart Below Conveyor Frame See Chart Below Bed Plate 506SSP Sleeve,.5 Magnet Stainless Steel 5 807 07 Flat Head Screw M x 0mm 6 808 00 Magnet.5 Dia x.5 Long 7 9069M Socket Head Screw M6 x 0mm 8 9069M Socket Head Screw M6 x mm Item : Conveyor Frame Length Part Number (60mm) 0WW 0908 (9mm) 0WW 008 (9mm) 0WW 008 5 (5mm) 0WW 05508 6 (89mm) 0WW 06708 7 (mm) 0WW 07908 8 (8mm) 0WW 0908 9 (7mm) 0WW 008 0 (08mm) 0WW 508 (5mm) 0WW 708 (658mm) 0WW 908 (96mm) 0WW 06708 0WW 07908* (67mm) 0WW 06708 0WW 0908* 5 (57mm) 0WW 06708 0WW 008* 6 (877mm) 0WW 06708 0WW 508* 7 (58mm) 0WW 06708 0WW 708* 8 (586mm) 0WW 06708 0WW 908* WW = Conveyor width reference: 0, 0, 05, 06 * = 6 (5mm) and wider conveyors Item : Bed Plate Length Part Number (60mm) 05WW 090 (9mm) 05WW 00 (9mm) 05WW 00 5 (5mm) 05WW 0550 6 (89mm) 05WW 0670 7 (mm) 05WW 0790 8 (8mm) 05WW 090 9 (7mm) 05WW 00 0 (08mm) 05WW 50 (5mm) 05WW 70 (658mm) 05WW 90 (96mm) 05WW 0796 0WW 0790* (67mm) 05WW 0796 0WW 090* 5 (57mm) 05WW 0796 0WW 00* 6 (877mm) 05WW 0796 0WW 50* 7 (58mm) 05WW 0796 0WW 70* 8 (586mm) 05WW 0796 0WW 90* WW = Conveyor Width reference: 0, 0, 05, 06 * = 6 (5mm) and wider conveyors Dorner Mfg. Corp. 85-5 Rev. B

8 (0mm) to (605mm) Wide Conveyor Assembly 6 6 9 9 7 5 9 0 7 5 9 8 9 8 6 05 Head Plate LH 06 Head Plate RH 07 Bearing Cover Disk 08 Bearing 5 09 Tension Slide Bar 6 00 Taper Screw 7 00 Rack Gear.5 PA x P 8 0608 Drive Spindle 8 (0mm) 060 Drive Spindle 0 (5mm) 06 Drive Spindle (05mm) 9 0708 Idler Spindle 8 (0mm) 070 Idler Spindle 0 (5mm) 07 Idler Spindle (05mm) 0 0008M Pinion Gear 8 (0mm) 000M 00M See Chart Below See Chart Below See Chart Below Pinion Gear 0 (5mm) Pinion Gear (05mm) Side Rail RH 8 Wide (0 60mm) Side Rail LH 8 Wide (0 60mm) Center Rail 8 Wide (0 05mm) 85-5 Rev. B Dorner Mfg. Corp.

See Chart Below Bed Plate 5 506SSP Sleeve.5 Magnet Stainless Steel 6 807 07 Flat Head Screw M x 0mm 7 808 00 Magnet.5 DIA x.5 Long 8 9069M Socket Head Screw M6 x 0mm 9 9069M Socket Head Screw M6 x mm Item : Side Rail RH 8 Wide (0 60mm) Length Part Number (60mm) 0 0908 (9mm) 0 008 (9mm) 0 008 5 (5mm) 0 05508 6 (89mm) 0 06708 7 (mm) 0 07908 8 (8mm) 0 0908 9 (7mm) 0 008 0 (08mm) 0 508 (5mm) 0 708 (658mm) 0 908 (96mm) 0 0700 0 07908 (67mm) 0 0700 0 0908 5 (57mm) 0 0700 0 008 6 (877mm) 0 0700 0 508 7 (58mm) 0 0700 0 708 8 (586mm) 0 0700 0 908 Item : Side Rail LH 8 Wide (0 60mm) Length Part Number (60mm) 0 0908 (9mm) 0 008 (9mm) 0 008 5 (5mm) 0 05508 6 (89mm) 0 06708 7 (mm) 0 07908 8 (8mm) 0 0908 9 (7mm) 0 008 0 (08mm) 0 508 (5mm) 0 708 (658mm) 0 908 (96mm) 0 0700 0 07908 (67mm) 0 0700 0 0908 5 (57mm) 0 0700 0 008 6 (877mm) 0 0700 0 508 7 (58mm) 0 0700 0 708 8 (586mm) 0 0700 0 908 Item : Center Rail 8 Wide (0 05mm) Length Part Number (60mm) 0 07 (9mm) 0 07 (9mm) 0 067 5 (5mm) 0 087 6 (89mm) 0 0607 7 (mm) 0 077 8 (8mm) 0 087 9 (7mm) 0 0967 0 (08mm) 0 087 (5mm) 0 07 (658mm) 0 7 (96mm) 0 0700 0 077 (67mm) 0 0700 0 087 5 (57mm) 0 0700 0 0967 6 (877mm) 0 0700 0 087 7 (58mm) 0 0700 0 07 8 (586mm) 0 0700 0 7 Item : Bed Plate Length Part Number (60mm) 05WW 090 (9mm) 05WW 00 (9mm) 05WW 00 5 (5mm) 05WW 0550 6 (89mm) 05WW 0670 7 (mm) 05WW 0790 8 (8mm) 05WW 090 9 (7mm) 05WW 00 0 (08mm) 05WW 50 (5mm) 05WW 70 (658mm) 05WW 90 (96mm) 05WW 0796 05WW 0790 (67mm) 05WW 0796 05WW 090 5 (57mm) 05WW 0796 05WW 00 6 (877mm) 05WW 0796 05WW 50 7 (58mm) 05WW 0796 05WW 70 8 (586mm) 05WW 0796 05WW 90 WW = Conveyor Width reference: 08, 0, Dorner Mfg. Corp. 85-5 Rev. B

8 (57mm) to (60mm) Wide Conveyor Assembly 7 5 0 6 0 0 8 6 7 8 5 0 9 9 0 5 7 05 Head Plate LH 06 Head Plate RH 07 Bearing Cover Disk 08 Bearing 5 09 Tension Slide Bar 6 00 Taper Screw 7 07 Center Rail Cross Support 8 (57mm) 08 Center Rail Cross Support (5mm) 09 Center Rail Cross Support (60mm) 8 00 Rack Gear.5 PA x P 9 068 Drive Spindle 8 (57mm) 06 Drive Spindle (5mm) 06 Drive Spindle (60mm) 0 078 Idler Spindle 8 (57mm) 07 Idler Spindle (5mm) 07 Idler Spindle (60mm) 008M Pinion Gear 8 (57mm) 00M 00M See Chart Below See Chart Below See Chart Below Pinion Gear (5mm) Pinion Gear (60mm) Side Rail RH 8 Wide (0 60mm) Side Rail LH 8 Wide (0 60mm) Center Rail 8 Wide (0 05mm) 5 See Chart Below Bed Plate 6 506SSP Sleeve.5 Magnet Stainless Steel 85-5 Rev. B Dorner Mfg. Corp.

7 807 07 Flat Head Screw M x 0mm 8 808 00 Magnet.5 DIA x.5 Long 9 9069M Socket Head Screw M6 x 0mm 0 9069M Socket Head Screw M6 x mm Item : Side Rail RH 8 Wide (0 60mm) Length Part Number (60mm) 0 0908 (9mm) 0 008 (9mm) 0 008 5 (5mm) 0 05508 6 (89mm) 0 06708 7 (mm) 0 07908 8 (8mm) 0 0908 9 (7mm) 0 008 0 (08mm) 0 508 (5mm) 0 708 (658mm) 0 908 (96mm) 0 0700 0 07908 (67mm) 0 0700 0 0908 5 (57mm) 0 0700 0 008 6 (877mm) 0 0700 0 508 7 (58mm) 0 0700 0 708 8 (586mm) 0 0700 0 908 Item : Side Rail LH 8 Wide (0 60mm) Length Part Number (60mm) 0 0908 (9mm) 0 008 (9mm) 0 008 5 (5mm) 0 05508 6 (89mm) 0 06708 7 (mm) 0 07908 8 (8mm) 0 0908 9 (7mm) 0 008 0 (08mm) 0 508 (5mm) 0 708 (658mm) 0 908 (96mm) 0 0700 0 07908 (67mm) 0 0700 0 0908 5 (57mm) 0 0700 0 008 6 (877mm) 0 0700 0 508 7 (58mm) 0 0700 0 708 8 (586mm) 0 0700 0 908 Item : Center Rail 8 Wide (0 05mm) Length Part Number (60mm) 0 00998 (9mm) 0 098 (9mm) 0 098 5 (5mm) 0 098 6 (89mm) 0 05798 7 (mm) 0 06998 8 (8mm) 0 0898 9 (7mm) 0 0998 0 (08mm) 0 0598 (5mm) 0 798 (658mm) 0 998 (96mm) 0 06700 0 06998 (67mm) 0 06700 0 0898 5 (57mm) 0 06700 0 0998 6 (877mm) 0 06700 0 0598 7 (58mm) 0 06700 0 798 8 (586mm) 0 06700 0 998 Item 5: Bed Plate Length Part Number (60mm) 05WW 090 (9mm) 05WW 00 (9mm) 05WW 00 5 (5mm) 05WW 0550 6 (89mm) 05WW 0670 7 (mm) 05WW 0790 8 (8mm) 05WW 090 9 (7mm) 05WW 00 0 (08mm) 05WW 50 (5mm) 05WW 70 (658mm) 05WW 90 (96mm) 05WW 0796 05WW 0790 (67mm) 05WW 0796 05WW 090 5 (57mm) 05WW 0796 05WW 00 6 (877mm) 05WW 0796 05WW 50 7 (58mm) 05WW 0796 05WW 70 8 (586mm) 05WW 0796 05WW 90 WW = Conveyor Width reference: 08, 0, Dorner Mfg. Corp. 5 85-5 Rev. B

Nosebar End Assembly (5mm) to (60mm) Wide 6 9 0 8 0 7 5 0965 Mounting Block, PLT Spindle 0760 Flex Link Bar (5mm) 0760 Flex Link Bar (76mm) 0760 Flex Link Bar (0mm) 07605 Flex Link Bar 5 (7mm) 07606 Flex Link Bar 6 (5mm) 07608 Flex Link Bar 8 (0mm) 0760 Flex Link Bar 0 (5mm) 076 Flex Link Bar (05mm) 0768 Flex Link Bar 8 (57mm) 076 Flex Link Bar (5mm) 076 Flex Link Bar (60mm) 5 Outer Side Plate 6 Inner Side Plate LH 5 7 Inner Side Plate RH 6 8 Head Plate Bar 7 0 Nosebar (5mm) 0 Nosebar (76mm) 0 Nosebar (0mm) 05 Nosebar 5 (7mm) 06 Nosebar 6 (5mm) 08 Nosebar 8 (0mm) 0 Nosebar 0 (5mm) Nosebar (05mm) 8 Nosebar 8 (57mm) Nosebar (5mm) Nosebar (60mm) 8 0 Nosebar Rod (5mm) 0 Nosebar Rod (76mm) 0 Nosebar Rod (0mm) 05 Nosebar Rod 5 (7mm) 06 Nosebar Rod 6 (5mm) 08 Nosebar Rod 8 (0mm) 0 Nosebar Rod 0 (5mm) Nosebar Rod (05mm) 8 Nosebar Rod 8 (57mm) Nosebar Rod (5mm) Nosebar Rod (60mm) 9 00695P Knurl Pin.5 DIA x.97 Lg 0 80 Nose Bar Roller 9058M Sockety Head Screw M5 x 8mm 9059M Socket Head Screw M5 x 6mm 9069M Socket Head Screw M6 x mm 905M Flat Head Screw M5 x mm 85-5 Rev. B 6 Dorner Mfg. Corp.

0 (76mm) Aluminum Side For Conveyors For 8 Conveyors 00 Guide Retaining Clip See Chart Below 00 Guide (76mm) HS 00695P Single Drop in Tee Bar 9069M Socket Head Screw M6 x 0mm Item : 00 Guide (76mm) HS Length End Guide End Guide (60mm) Left Hand 800 000 N/A Right Hand 800 000 N/A (9mm) Left Hand 800 0600 N/A Right Hand 800 0600 N/A (9mm) Left Hand 800 0800 N/A Right Hand 800 0800 N/A 5 (5mm) Left Hand 800 06000 N/A Right Hand 800 06000 N/A 6 (89mm) Left Hand 800 0700 N/A Right Hand 800 0700 N/A 7 (mm) Left Hand 800 0800 N/A Right Hand 800 0800 N/A 8 (8mm) Left Hand 800 09600 N/A Right Hand 800 09600 N/A 9 (7mm) Left Hand 800 0800 N/A Right Hand 800 0800 N/A 0 (08mm) Left Hand 800 000 N/A Right Hand 800 000 N/A (5mm) Left Hand 800 00 N/A Right Hand 800 00 N/A (658mm) Left Hand 800 00 N/A Right Hand 800 00 N/A (96mm) Left Hand 800 07500 800 0800 Right Hand 800 07500 800 0800 (67mm) Left Hand 800 07500 800 0900 Right Hand 800 07500 800 0900 5 (57mm) Left hand 800 07500 800 0500 Right Hand 800 07500 800 0500 6 (877mm) Left Hand 800 07500 800 700 Right Hand 800 07500 800 700 7 (58mm) Left Hand 800 07500 800 900 Right Hand 800 07500 800 900 8 (586mm) Left Hand 800 07500 800 00 Right Hand 800 07500 800 00 Dorner Mfg. Corp. 7 85-5 Rev. B

05.5 (8mm) Aluminum Side For Conveyors For 8 Conveyors 00 Guide Retaining Clip See Chart Below 00 Guide.5 (mm) HS 6997M Single Drop in Tee Bar 9069M Socket Head Screw M6 x 0mm Item : 00 Guide.5 (mm) HS Length End Guide End Guide (60mm) Left Hand 8050 000 N/A Right Hand 8050 000 N/A (9mm) Left Hand 8050 0600 N/A Right Hand 8050 0600 N/A (9mm) Left Hand 8050 0800 N/A Right Hand 8050 0800 N/A 5 (5mm) Left Hand 8050 06000 N/A Right Hand 8050 06000 N/A 6 (89mm) Left Hand 8050 0700 N/A Right Hand 8050 0700 N/A 7 (mm) Left Hand 8050 0800 N/A Right Hand 8050 0800 N/A 8 (8mm) Left Hand 8050 09600 N/A Right Hand 8050 09600 N/A 9 (7mm) Left Hand 8050 0800 N/A Right Hand 8050 0800 N/A 0 (08mm) Left Hand 8050 000 N/A Right Hand 8050 000 N/A (5mm) Left Hand 8050 00 N/A Right Hand 8050 00 N/A (658mm) Left Hand 8050 00 N/A Right Hand 8050 00 N/A (96mm) Left Hand 8050 07500 8050 0800 Right Hand 8050 07500 8050 0800 (67mm) Left Hand 8050 07500 8050 0900 Right Hand 8050 07500 8050 0900 5 (57mm) Left hand 8050 07500 8050 0500 Right Hand 8050 07500 8050 0500 6 (877mm) Left Hand 8050 07500 8050 700 Right Hand 8050 07500 8050 700 7 (58mm) Left Hand 8050 07500 8050 900 Right Hand 8050 07500 8050 900 8 (586mm) Left Hand 8050 07500 8050 00 Right Hand 8050 07500 8050 00 85-5 Rev. B 8 Dorner Mfg. Corp.

07 Low to Side Wiper For Conveyors For 8 Conveyors 5 00 Guide Retaining Clip See Chart Below 00 Guide.5 (mm) HS 00 Side Wiper Nylatron (per foot) 6997M Single Drop in Tee Bar 5 9069M Socket Head Screw M6 x 0mm Item : 00 Guide.5 (mm) HS Length End Guide End Guide (60mm) Left Hand 8090 000 N/A Right Hand 8090 000 N/A (9mm) Left Hand 8090 0600 N/A Right Hand 8090 0600 N/A (9mm) Left Hand 8090 0800 N/A Right Hand 8090 0800 N/A 5 (5mm) Left Hand 8090 06000 N/A Right Hand 8090 06000 N/A 6 (89mm) Left Hand 8090 0700 N/A Right Hand 8090 0700 N/A 7 (mm) Left Hand 8090 0800 N/A Right Hand 8090 0800 N/A 8 (8mm) Left Hand 8090 09600 N/A Right Hand 8090 09600 N/A 9 (7mm) Left Hand 8090 0800 N/A Right Hand 8090 0800 N/A 0 (08mm) Left Hand 8090 000 N/A Right Hand 8090 000 N/A (5mm) Left Hand 8090 00 N/A Right Hand 8090 00 N/A (658mm) Left Hand 8090 00 N/A Right Hand 8090 00 N/A (96mm) Left Hand 8090 07500 8090 0800 Right Hand 8090 07500 8090 0800 (67mm) Left Hand 8090 07500 8090 0900 Right Hand 8090 07500 8090 0900 5 (57mm) Left hand 8090 07500 8090 0500 Right Hand 8090 07500 8090 0500 6 (877mm) Left Hand 8090 07500 8090 700 Right Hand 8090 07500 8090 700 7 (58mm) Left Hand 8090 07500 8090 900 Right Hand 8090 07500 8090 900 8 (586mm) Left Hand 8090 07500 8090 00 Right Hand 8090 07500 8090 00 Dorner Mfg. Corp. 9 85-5 Rev. B

09 Low to High Side For Conveyors For 8 Conveyors 00 Guide Retaining Clip See Chart Below 00 Guide.5 (mm) HS 6997M Single Drop in Tee Bar 9069M Socket Head Screw M6 x 0mm Item : 00 Guide.5 (mm) HS Length End Guide End Guide (60mm) Left Hand 8090 000 N/A Right Hand 8090 000 N/A (9mm) Left Hand 8090 0600 N/A Right Hand 8090 0600 N/A (9mm) Left Hand 8090 0800 N/A Right Hand 8090 0800 N/A 5 (5mm) Left Hand 8090 06000 N/A Right Hand 8090 06000 N/A 6 (89mm) Left Hand 8090 0700 N/A Right Hand 8090 0700 N/A 7 (mm) Left Hand 8090 0800 N/A Right Hand 8090 0800 N/A 8 (8mm) Left Hand 8090 09600 N/A Right Hand 8090 09600 N/A 9 (7mm) Left Hand 8090 0800 N/A Right Hand 8090 0800 N/A 0 (08mm) Left Hand 8090 000 N/A Right Hand 8090 000 N/A (5mm) Left Hand 8090 00 N/A Right Hand 8090 00 N/A (658mm) Left Hand 8090 00 N/A Right Hand 8090 00 N/A (96mm) Left Hand 8090 07500 8090 0800 Right Hand 8090 07500 8090 0800 (67mm) Left Hand 8090 07500 8090 0900 Right Hand 8090 07500 8090 0900 5 (57mm) Left hand 8090 07500 8090 0500 Right Hand 8090 07500 8090 0500 6 (877mm) Left Hand 8090 07500 8090 700 Right Hand 8090 07500 8090 700 7 (58mm) Left Hand 8090 07500 8090 900 Right Hand 8090 07500 8090 900 8 (586mm) Left Hand 8090 07500 8090 00 Right Hand 8090 07500 8090 00 85-5 Rev. B 0 Dorner Mfg. Corp.

0.5 (mm) Extruded Plastic For Conveyors For 8 Conveyors 5 00 Guide Retaining Clip 0005P Snap On Guide (per foot) See Chart Below 00 Guide 6997M Single Drop in Tee Bar 5 9069M Socket Head Screw M6 x 0mm Item : 00 Guide Length End Guide End Guide (60mm) Left Hand 800 000 N/A Right Hand 800 000 N/A (9mm) Left Hand 800 0600 N/A Right Hand 800 0600 N/A (9mm) Left Hand 800 0800 N/A Right Hand 800 0800 N/A 5 (5mm) Left Hand 800 06000 N/A Right Hand 800 06000 N/A 6 (89mm) Left Hand 800 0700 N/A Right Hand 800 0700 N/A 7 (mm) Left Hand 800 0800 N/A Right Hand 800 0800 N/A 8 (8mm) Left Hand 800 09600 N/A Right Hand 800 09600 N/A 9 (7mm) Left Hand 800 0800 N/A Right Hand 800 0800 N/A 0 (08mm) Left Hand 800 000 N/A Right Hand 800 000 N/A (5mm) Left Hand 800 00 N/A Right Hand 800 00 N/A (658mm) Left Hand 800 00 N/A Right Hand 800 00 N/A (96mm) Left Hand 800 07500 800 0800 Right Hand 800 07500 800 0800 (67mm) Left Hand 800 07500 800 0900 Right Hand 800 07500 800 0900 5 (57mm) Left hand 800 07500 800 0500 Right Hand 800 07500 800 0500 6 (877mm) Left Hand 800 07500 800 700 Right Hand 800 07500 800 700 7 (58mm) Left Hand 800 07500 800 900 Right Hand 800 07500 800 900 8 (586mm) Left Hand 800 07500 800 00 Right Hand 800 07500 800 00 Dorner Mfg. Corp. 85-5 Rev. B

Adjustable Guiding 8 7 9 5 0 6 098 Aluminum Profile Guide (60mm) 098 Aluminum Profile Guide (9mm) 0985 Aluminum Profile Guide (9mm) 0986 Aluminum Profile Guide 5 (5mm) 0987 Aluminum Profile Guide 6 (89mm) 0988 Aluminum Profile Guide 7 (mm) 0989 Aluminum Profile Guide 8 (8mm) 0990 Aluminum Profile Guide 9 (7mm) 099 Aluminum Profile Guide 0 (08mm) 099 Aluminum Profile Guide (5mm) 099 Aluminum Profile Guide (658mm) 099 Aluminum Profile Guide (96mm) 0080M Drop In Tee Bar 000 Mounting Bracket 007M Guide Mounting Shaft Vertical 5 008M Guide Moutning Shaft Horizontal 6 6775MP Square Nut 7 807 65 Cross Block 8 807 98 Vinyl Shaft Cap 9 6068P Flat Extruded Guide (per foot) 0 906M Socket Head Screw M6 x mm 9066M Socket Head Screw M6 x 6mm 85-5 Rev. B Dorner Mfg. Corp.

.5 (mm) Cleated Guiding For Conveyors For 8 Conveyors 00 Guide Retaining Clip See Chart Below 00 Guide.7 (mm) Cleated 6997M Drop In Tee Bar 9069M Socket Head Screw M6 x 0mm Item : 00 Guide Length End Guide End Guide (60mm) Left Hand 860 056 N/A Right Hand 860 056 N/A (9mm) Left Hand 860 056 N/A Right Hand 860 056 N/A (9mm) Left Hand 860 0656 N/A Right Hand 860 0656 N/A 5 (5mm) Left Hand 860 05856 N/A Right Hand 860 05856 N/A 6 (89mm) Left Hand 860 07056 N/A Right Hand 860 07056 N/A 7 (mm) Left Hand 860 0856 N/A Right Hand 860 0856 N/A 8 (8mm) Left Hand 860 0956 N/A Right Hand 860 0956 N/A 9 (7mm) Left Hand 860 0656 N/A Right Hand 860 0656 N/A 0 (08mm) Left Hand 860 856 N/A Right Hand 860 856 N/A (5mm) Left Hand 860 056 N/A Right Hand 860 056 N/A (658mm) Left Hand 860 56 N/A Right Hand 860 56 N/A (96mm) Left Hand 860 078 860 0808 Right Hand 860 078 860 0808 (67mm) Left Hand 860 078 860 098 Right Hand 860 078 860 098 5 (57mm) Left hand 860 078 860 08 Right Hand 860 078 860 08 6 (877mm) Left Hand 860 078 860 68 Right Hand 860 078 860 68 7 (58mm) Left Hand 860 078 860 88 Right Hand 860 078 860 88 8 (586mm) Left Hand 860 078 860 08 Right Hand 860 078 860 08 Dorner Mfg. Corp. 85-5 Rev. B

(5mm) Cleated Guiding For Conveyors For 8 Conveyors 00 Guide Retaining Clip See Chart Below 00 Guide (5mm) Cleated 6997M Drop In Tee Bar 9069M Socket Head Screw M6 x 0mm Item : 00 Guide Length End Guide End Guide (60mm) Left Hand 870 056 N/A Right Hand 870 056 N/A (9mm) Left Hand 870 056 N/A Right Hand 870 056 N/A (9mm) Left Hand 870 0656 N/A Right Hand 870 0656 N/A 5 (5mm) Left Hand 870 05856 N/A Right Hand 870 05856 N/A 6 (89mm) Left Hand 870 07056 N/A Right Hand 870 07056 N/A 7 (mm) Left Hand 870 0856 N/A Right Hand 870 0856 N/A 8 (8mm) Left Hand 870 0956 N/A Right Hand 870 0956 N/A 9 (7mm) Left Hand 870 0656 N/A Right Hand 870 0656 N/A 0 (08mm) Left Hand 870 856 N/A Right Hand 870 856 N/A (5mm) Left Hand 870 056 N/A Right Hand 870 056 N/A (658mm) Left Hand 870 56 N/A Right Hand 870 56 N/A (96mm) Left Hand 870 078 870 0808 Right Hand 870 078 870 0808 (67mm) Left Hand 870 078 870 098 Right Hand 870 078 870 098 5 (57mm) Left hand 870 078 870 08 Right Hand 870 078 870 08 6 (877mm) Left Hand 870 078 870 68 Right Hand 870 078 870 68 7 (58mm) Left Hand 870 078 870 88 Right Hand 870 078 870 88 8 (586mm) Left Hand 870 078 870 08 Right Hand 870 078 870 08 85-5 Rev. B Dorner Mfg. Corp.

(5mm) Cleated Guiding For Conveyors For 8 Conveyors 00 Guide Retaining Clip See Chart Below 00 Guide. Cleated 6997M Drop In Tee Bar 9069M Socket Head Screw M6 x 0mm Item : 00 Guide Length End Guide End Guide (60mm) Left Hand 890 056 N/A Right Hand 890 056 N/A (9mm) Left Hand 890 056 N/A Right Hand 890 056 N/A (9mm) Left Hand 890 0656 N/A Right Hand 890 0656 N/A 5 (5mm) Left Hand 890 05856 N/A Right Hand 890 05856 N/A 6 (89mm) Left Hand 890 07056 N/A Right Hand 890 07056 N/A 7 (mm) Left Hand 890 0856 N/A Right Hand 890 0856 N/A 8 (8mm) Left Hand 890 0956 N/A Right Hand 890 0956 N/A 9 (7mm) Left Hand 890 0656 N/A Right Hand 890 0656 N/A 0 (08mm) Left Hand 890 856 N/A Right Hand 890 856 N/A (5mm) Left Hand 890 056 N/A Right Hand 890 056 N/A (658mm) Left Hand 890 56 N/A Right Hand 890 56 N/A (96mm) Left Hand 890 078 890 0808 Right Hand 890 078 890 0808 (67mm) Left Hand 890 078 890 098 Right Hand 890 078 890 098 5 (57mm) Left hand 890 078 890 08 Right Hand 890 078 890 08 6 (877mm) Left Hand 890 078 890 68 Right Hand 890 078 890 68 7 (58mm) Left Hand 890 078 890 88 Right Hand 890 078 890 88 8 (586mm) Left Hand 890 078 890 08 Right Hand 890 078 890 08 Dorner Mfg. Corp. 5 85-5 Rev. B

Flared Side Guiding 7 5 6 00 Guide Retaining Clip 0 0 0 05 06 Side Flare Mounting Guide (60mm) Side Flare Mounting Guide (9mm) Side Flare Mounting Guide (9mm) Side Flare Mounting Guide 5 (5mm) Side Flare Mounting Guide 6 (89mm) 05M Flared Guide 5 (60mm) 05M Flared Guide 5 (9mm) 05M Flared Guide 5 (9mm) 05M Flared Guide 5 5 (5mm) 05M Flared Guide 5 6 (89mm) 6997 Drop In Tee Bar 5 90506M Button Head Screw M5 x 6mm 6 9 5 Washer 7 9069M Cap Low Head Screw M6 x 0mm 85-5 Rev. B 6 Dorner Mfg. Corp.

Flat Belt Mounting Brackets 6 5 08 Stand Mount 0050M Drop In Tee Bar 60579P Washer 807 90 Square Nut M6 5mm x 0mm 5 9060M Socket Head Screw M6 x 0mm 6 9069M Socket Head Screw M6 x mm Cleated Belt Mounting Brackets 6 5 086 Cleated Mounting Assembly 0050M Drop In Tee Bar 60579P Washer 807 90 Square Nut M6 5mm x 0mm 5 9060M Socket Head Screw M6 x 0mm 6 9069M Socket Head Screw M6 x mm Dorner Mfg. Corp. 7 85-5 Rev. B

Flat Belt Mounting Brackets for (60mm) Conveyors 5 6 7 08 Stand Mount, LH (60mm) 08 Stand Mount, RH (60mm) 60579P Washer Cleated Belt Mounting Brackets for (60mm) Conveyors 6997M Drop In Tee Bar 5 807 90 Square Nut M6 5mm x 0mm 6 9060M Socket Head Screw M6 x 0mm 7 9069M Socket Head Screw M6 x mm 5 7 6 085 085 60579P Washer Cleated Stand Bracket Assembly LH (60mm) Conveyor Cleated Stand Bracket Assembly RH (60mm) Conveyor 6997M Drop In Tee Bar 5 807 90 Square Nut M6 5mm x 0mm 6 9060M Socket Head Screw M6 x 0mm 7 9069M Socket Head Screw M6 x mm 85-5 Rev. B 8 Dorner Mfg. Corp.

Connecting Assembly without Stand Mount 0 Frame Bar Connector Flat Belt Connecting Assembly with Stand Mount 005M Intermediate Clamp Plate 9069M Socket Head Screw M6 x mm 6 5 0 Frame Connector Bar 087 Stand Mount Joint 60579P Washer 807 90 Square Nut M6 5mm x 0mm 5 9060M Socket Head Screw M6 x 0mm 6 9069M Socket Head Screw M6 x mm Dorner Mfg. Corp. 9 85-5 Rev. B

Cleated Belt Connecting Assembly with Stand Mount 6 5 0 Frame Connector Bar 086 Cleat Stand Bracket Assembly 60579P Washer 807 90 Square Nut M6 5mm x 0mm 5 9060M Socket Head Screw M6 x 0mm 6 9069M Socket Head Screw M6 x mm (5mm) to 6 (5mm) Flat Belt Return Roller 5 085 Short Return Roller Guard 087 Return Roller Clip 80 Bearing 9 00 Dowel Pin 5 9069M Socket Head Screw M6 x 6mm 85-5 Rev. B 0 Dorner Mfg. Corp.

8 (0mm) to (60mm) Flat Belt Return Roller 5 086 Return Roller 087 Return Roller Clip 0908 Return Roller Guard 8 (0mm) 090 Return Roller Guard 0 (5mm) 09 Return Roller Guard (05mm) 098 Return Roller Guard 8 (57mm) 09 Return Roller Guard 8 (5mm) 09 Return Roller Guard (60mm) 008 Return Roller Rod 8 (0mm) 00 Return Roller Rod 0 (5mm) 0 Return Roller Rod (05mm) 08 Return Roller Rod 8 (57mm) 0 Return Roller Rod (5mm) 0 Return Roller Rod (60mm) 5 9069M Socket Head Screw M6 x 6mm Cleated Belt Return Roller 5 085 Short Return Roller Guard 088 Cleated Return Roller Clip 80 Bearing 9 00 Dowel Pin 5 9069M Socket Head Screw M6 x 6mm Dorner Mfg. Corp. 85-5 Rev. B

Conveyor Belt Part Number Configuration Flat Belt Conveyor Model Number 0 M WW LLLL A PP BB Cleated Belt Conveyor Model Number C M WW LLLL A SSSS Figure 50 Flat Belt Part Number Configuration Refer to Dorner patent plate (Figure 50). From the model number, determine conveyor width ( WW ), length ( LLLL ) and belt type ( BB ). Use data to configure belt part number as indicated below. *Add V for V-guided belts. - WW LLLL / BB V* - (Fill In) / V * Cleated Belt Part Number Configuration Refer to Dorner patent plate (Figure 50). From the model number, determine conveyor width ( WW ), length ( LLLL ), cleat type ( C ) and cleat spacing ( SSSS ). Use data to configure belt part number as indicated below. *Add V for V-guided belts. - WW LLLL C SSSS V* - (Fill In) V * 85-5 Rev. B Dorner Mfg. Corp.

Notes Dorner Mfg. Corp. 85-5 Rev. B

Return Policy No returns will be accepted without prior written factory authorization. When calling for authorization, please have the following information ready for the Dorner Factory representative or your local distributor:. Name and address of customer.. Item(s) being returned.. Reason for return.. Customer s original order number used when ordering the item(s). 5. Dorner or distributor invoice number. A representative will discuss action to be taken on the Returned items and provide a Returned Goods Authorization Number to reference. There will be a 5% restocking charge on all new items returned for credit where Dorner was not at fault. These will not be accepted after 60 days from original invoice date. The restocking charge covers inspection, cleaning, disassembly, and reissuing to inventory. If a replacement is needed prior to evaluation of returned item, a purchase order must be issued. Credit (if any) is issued only after return and evaluation is complete. Dorner has representatives throughout the world. Feel free to contact Dorner for the name of your local representative. Our technical sales and service staff will gladly help with your questions on Dorner products. For a copy of Dorner s Limited Warranty, contact factory, distributor, service center or visit our website at www.dorner.com. For replacement parts, contact an authorized Dorner Service Center or the factory. Dorner Mfg. Corp. reserves the right to change or discontinue products without notice. All products and services are covered in accordance with our standard warranty. All rights reserved. Dorner Mfg. Corp. 000 DORNER MFG. CORP. 975 Cottonwood Ave., PO Box 0 Hartland, WI 509-000 USA USA TEL -800-97-866 (USA) FAX -800-69-0 (USA) Outside the USA: TEL -6-67-7600, FAX -6-67-587 DORNER Arnold-Sommerfeld-Ring D-599 Baesweiler Germany TEL (00) 80 5 90 FAX (00) 80 5 9 Internet: www.dorner.com 85-5 Rev. A Printed in U.S.A. 00