Instruction and Assembly Manual

Instruction and Assembly Manual.90m, 1.0m & 1.2m SMC ANTENNA SYSTEM WITH AZ/EL CAP MOUNT TYPE 900 -.9m TYPE 100-1.0m TYPE 120-1.2m SMC ANTENNA WITH AZ/EL CAP MOUNT (UK) Limited Premier Business Park, Croft Head Road, Off Philips Road Whitebirk Industrial Estate Blackburn, Lancashire England BB1 5UE (0254) 680444 Fax (0254) 672299 1315 Industrial Park Drive, P.O. Box 1416 Smithfield, N.C. 27577 U.S.A. (919) 989-2242 Fax (919) 989-2200 8000284 Rev. H 3/99

VSAT ANTENNA/MOUNT/LNB LIMITED TWELVE (12) MONTH WARRANTY This CHANNEL MASTER equipment is warranted to be free from defects in material and workmanship under normal use and service. CHANNEL MASTER shall repair or replace defective equipment, at no charge, or at its option, refund the purchase price, if the equipment is returned to CHANNEL MASTER not more than twelve (12) months after shipment. Removal or reinstallation of equipment and its transportation shall not be at the cost of CHANNEL MASTER except CHANNEL MASTER shall return repaired or replaced equipment freight prepaid. This Warranty shall not apply to equipment which has been repaired or altered in any way so as to affect its stability or durability, or which has been subject to misuse, negligence or accident. This Warranty does not cover equipment which has been impaired by severe weather conditions such as excessive wind, ice, storms, lightning, or other natural occurrences over which CHANNEL MASTER has no control, and this Warranty shall not apply to equipment which has been operated or installed other than in accordance with the instructions furnished by CHANNEL MASTER. Claimants under this Warranty shall present their claims along with the defective equipment to CHANNEL MASTER immediately upon failure. Non-compliance with any part of this claim procedure may invalidate this warranty in whole or in part. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER AGREEMENTS AND WARRANTIES, ANY IMPLIED WARRANTY OF MER- CHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE IS LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY. CHANNEL MASTER DOES NOT AUTHORIZE ANY PERSON TO ASSUME FOR IT THE OBLIGATIONS CONTAINED IN THIS WARRANTY AND CHANNEL MASTER NEITHER ASSUMES NOR AUTHORIZES ANY REPRESENTATIVE OR OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE EQUIPMENT DELIVERED OR PROVIDED. IN NO EVENT SHALL CHANNEL MASTER BE LIABLE FOR ANY LOSS OF PROFITS, LOSS OF USE, INTERRUPTION OF BUSINESS, OR INDIRECT, SPECIAL OR CONSEQUENTIAL DAMAGES OF ANY KIND. In no event shall CHANNEL MASTER be liable for damages in an amount greater than the purchase price of the equipment. Some states do not allow limitations on how long an implied warranty lasts, or allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you.

DANGER!!! WATCH FOR WIRES! Installation of this product near power lines is dangerous. For your own safety, follow these important safety rules. 1. Perform as many functions as possible on the ground. 2. Watch out for overhead power lines. Check the distance to the power lines before starting installation. We recommend you stay a minimum of 6 meters (20 feet) from all power lines. 3. Do not use metal ladders. 4. Do not install antenna or mast assembly on a windy day. 5. If you start to drop antenna or mast assembly, get away from it and let it fall. 6. If any part of the antenna or mast assembly comes in contact with a power line, call your local power company. DO NOT TRY TO REMOVE IT YOURSELF! They will remove it safely. 7. Make sure that the mast assembly is properly grounded. WARNING!!! Assembling dish antennas on windy days can be dangerous. Because of the antenna surface, even slight winds create strong forces. For example, a 1.0m antenna facing a wind of 32 km/h (20 mph) can undergo forces of 269 N (60 lbs). Be prepared to safely handle these forces at unexpected moments. Do not attempt to assemble, move or mount a dish on windy days or serious, even fatal accidents may occur. Channel Master is not responsible or liable for damage or injury resulting from antenna installations. This manual covers the installation of the Channel Master 1.0m & 1.2m SMC antenna system with AZ/EL cap mount and Ku-single polarity feed. INTRODUCTION ASSEMBLY TOOLS REQUIRED SITE SELECTION For best results in the assembly process, perform each step in the same sequence as listed in this manual. The following list of tools are those required for hand assembly and installation of the antenna. 1 - Ratchet Wrench (³ ₈ Drive) 1-10mm Nut Driver 1-13mm Socket (³ ₈ Drive) 1-13mm Open/Box End Wrench 1 - Phillips Screwdriver 1 - Compass The first and most important consideration when choosing a prospective antenna site is whether or not the area can provide an acceptable look angle at the satellites. A site with a clear, unobstructed view from a suitable roof or wall facing south, southeast or southwest is required.your antenna site must be selected in advance so that you will be able to receive the strongest signal available. To avoid obstructions, it is important to conduct an on-site survey with a portable antenna. As with any type of construction, a local permit may be required before installing an antenna. It is the owner s responsibility to obtain any and all permits. BOLT TORQUE GRADE 8.8 (8G) - YELLOW COLOR GRADE 2 - SILVER COLOR M6 M8 M10 M12 M16 M20 #10 ¹ ₄ IN. ⁵ ₁₆ IN. ³ ₈ IN. ¹ ₂ IN. ⁵ ₈ IN. ³ ₄ IN. 1 IN. 7 18 32 58 144 260 32 6 11 20 43 92 124 259 FT-LBS FT-LBS FT-LBS FT-LBS FT-LBS FT-LBS FT-LBS FT-LBS FT-LBS FT-LBS FT-LBS FT-LBS FT-LBS FT-LBS 9.5 24 43 79 195 353 3.6 8 15 27 58 125 168 351 N-m N-m N-m N-m N-m N-m N-m N-m N-m N-m N-m N-m N-m N-m APPLY 24 N-m (18 FT-LBS) OF TORQUE TO M8 BOLT APPLY 11 FT-LBS (15 N-m) OF TORQUE TO ⁵ ₁₆ BOLT

PIER FOUNDATIONS 37 72 GRADE 36 OVAL END d MIN. DIA. GROUND POLE INSTALLATION 2³ ₈ O.D. x 72 LONG 2³ ₈" O.D. 1" to 2" SLOPE FOR WATER RUN OFF BELOW FROST LINE PIER FOUNDATIONS DEEP FROST LINE FOUNDATIONS 37 72 1" to 2" SLOPE FOR WATER RUN OFF GRADE, 48" OVAL END d MIN. DIA. 2³ ₈" O.D. NOTE: 48" may be increased, concrete and length of rebar will increase accordingly. 2" (SEE NOTE) 1-1.5" APPROX. BELOW FROST LINE (4) #3 x 24" MIN. AT 90 APART (SEE NOTE) DEEP FROST LINE FOUNDATIONS ANT WIND VEL. DIM d CONC VOL. DIM d CONC VOL. GROUND POLE 80 MPH 9 1.5 FT 3 7 1.2 FT 3 90 MPH 11 2.2 FT 3 7 1.2 FT 3 Mo. 611652931.90M 100 MPH 13 3.0 FT 3 8 1.5 FT 3 110 MPH 15 4.0 FT 3 10 2.4 FT 3 SEE NOTE 1 125 MPH 18 5.8 FT 3 12 3.5 FT 3 80 MPH 10 1.8 FT 3 7 1.2 FT 3 Mo. 611652931 1.0M 90 MPH 13 3.0 FT 3 8 1.5 FT 3 100 MPH 15 4.0 FT 3 9 1.9 FT 3 SEE NOTE 2 108 MPH 16 4.6 FT 3 10 2.4 FT 3 POLE SPECIFICATIONS: 2 SCH 40 2³ ₈ O.D. x.154 Wall x 72 Long Steel - CM PN 611652931 w/oval End and Powder Paint Finish. 1. When wind velocity exceeds 108 MPH on the.90m antenna at heights shown, the ground pole must be a heavy wall pipe as follows: 2 pipe (2³ ₈ O.D.) Schedule 80 (.218 wall thickness) and purchased locally. Field weld ¹ ₄ x 1¹ ₂ x 5 key as shown in Fig. 1.0 to prevent rotation in the concrete or use 3 O.D. ground pole and AZ/EL cap. 2. These charted values based on using Model 611652931 ground pole, 2.375 O.D. x 1.54 wall. When wind velocity exceeds 108 MPH, use 3 O.D. ground pole and AZ/EL cap. 3. Pole and foundation design based on the following criteria: (a) Uniform Building Code Exposure C and 1.5 stability factor, (b) Vertical soil pressure of 2000 pounds per square foot, (c) Lateral soil pressure of 400 pounds per square foot, (d) Concrete compressive strength of 2500 pounds per square inc h in 28 days. 4. CAUTION - The foundation design shown does not represent an appropriate design for any specific locality since soil conditions vary and may not meet design criteria given in Note 1.You should consult a local professional engineer to determine your soil conditions and appropriate foundation. KEY ¹ ₄ x 1¹ ₂ x 5, FIG. 1.0.21.21 FIELD WELD 6" APPROX.

PIER FOUNDATIONS A L #3 REBAR X DIA. OF PIER, INSERT THRU HOLE IN TUBE & CENTER OPTIONAL d MIN. DIA. 3" O.D. NOTE: Clearance increases at elevations greater than 23. 1" to 2" SLOPE FOR WATER RUN OFF GRADE 36 (B) PIER FOUNDATIONS GROUND POLE INSTALLATION 3 O.D. x 68 & 72 LONG (SEE NOTE 2) BELOW FROST LINE DEEP FROST LINE FOUNDATIONS #3 REBAR LENGTH = d MIN LESS 1" INSERT THROUGH HOLE IN TUBE & CENTER A L 1" to 2" SLOPE FOR WATER RUN OFF, (4) #3 x 24" MIN. AT 90 APART (SEE NOTE) d MIN. DIA. 3" O.D. NOTE: 48" may be increased, concrete and length of rebar will increase accordingly. 2" GRADE 48" (B) 1-1.5" APPROX. BELOW FROST LINE DEEP FROST LINE FOUNDATIONS ANT WIND VEL. DIM L DIM A DIM d CONC VOL. DIM L DIM A DIM d CONC VOL. GROUND POLE 80 MPH 9 1.5 FT 3 7 1.2 FT 3 90 MPH 11 2.2 FT 3 7 1.2 FT 3.90M 110 MPH 68 37 13 3.0 FT 3 68 37 8 1.5 FT 3 Mo. 611652731 110 MPH 15 4.0 FT 3 10 2.4 FT 3 See Note 2 125 MPH 18 5.8 FT 3 12 3.5 FT 3 80 MPH 10 1.8 FT 3 7 1.2 FT 3 90 MPH 13 3.0 FT 3 8 1.5 FT 3 1.0M 110 MPH 68 37 15 4.0 FT 3 68 37 10 2.4 FT 3 Mo. 611652731 110 MPH 17 5.2 FT 3 11 2.9 FT 3 See Note 2 125 MPH 20 7.2 FT 3 14 4.7 FT 3 80 MPH 14 3.5 FT 3 9 1.9 FT 3 90 MPH 17 5.2 FT 3 11 2.9 FT 3 1.2M 110 MPH 72 39 19 6.5 FT 3 72 39 13 4.1 FT 3 Mo. 611685101 110 MPH 22 8.7 FT 3 15 5.4 FT 3 See Note 2 125 MPH 25 11.2 FT 3 19 8.7 FT 3 POLE SPECIFICATIONS: 3 O.D. x.120 Wall x 68 Long Steel w/powder Paint Finish - CM PN 611652731. 3 O.D. x.148 Wall x 72 Long Steel w/powder Paint Finish - CM PN 611685101. 1. Pole and foundation design based on the following criteria: (a) Uniform Building Code Exposure C and 1.5 stability factor, (b) Vertical soil pressure of 2000 pounds per square foot, (c) Lateral soil pressure of 400 pounds per square foot, (d) Concrete compressive strength of 2500 pounds per square inch in 28 days. 2. If Model 6851 (3 x 72 ) is used for.90m and 1.0m Antenna Dimension B on pier foundation must be increased by 4 and concrete volume will increase accordingly. 3. CAUTION - The foundation design shown does not represent an appropriate design for any specific locality since soil conditions vary and may not meet design criteria given in Note 1. You should consult a local professional engineer to determine your soil conditions and appropriate foundation.

ASSEMBLY AND INSTALLATION The AZ/EL Cap Mount can be installed on a 2³ ₈ or 3 O.D. ground tube, roof, or wall mount depending on model. The appropriate mount should be assembled and in place before installing the AZ/EL cap. As the AZ/EL cap mount is factory preassembled, there is no assembly required for the mount. ASSEMBLING ANTENNA TO CAP MOUNT Install four M8 x 60mm (2³ ₈ ) carriage bolts (1) into holes in center of reflector and assemble to cap mount flanges. (Reference Fig. 2.0) Install four lock washers (2) and hex nuts (3) on bolts. Tighten and torque to 11 ft.-lbs (15 N-m). IMPORTANT! Bottom feed leg hole to be located as shown in Fig. 2.0. INSTALLING CAP MOUNT ON MOUNT TUBE Lift reflector/cap mount assembly and slide cap mount onto mount tube (Reference Fig. 2.1). Swivel antenna assembly until reflector faces southward. Tighten M8 clamp nuts so that the antenna assembly is held stationary on tube, but can be swiveled with slight pressure. FEED AND FEED LEGS INSTALLATION Assemble feed assembly and feed legs to antenna as shown in Fig. 2.2. Insert bottom feed leg (4) into hole in bottom edge of antenna (5). NOTE: Bottom feed leg is the one with a slight bend on one end of leg, lance on opposite end, and is shorter than the two side legs (6). Install side legs (6) to antenna. From back side of antenna, secure with M6 x 30mm (¹ ₄ x 1³ ₁₆ ) hex bolts and ¹ ₄ special (⁷ ₈ O.D.) flat washer (7 & 8). Do not tighten. Insert bottom leg (4) into hole on center of junction block* (9) until lance on leg is engaged. Insert one side leg (6) into junction block* (9) and secure with M6 x 30mm (¹ ₄ x 1³ ₁₆ ) hex bolts and ¹ ₄ flat washer (7 & 10). Do not tighten. Insert opposite side leg (6) into junction block* (9) and secure with M6 x 30mm hex bolt and ¹ ₄ flat washer (7 & 10). Tighten and torque bolts securing side legs to junction block and antenna to 4 ft-lbs (5.4 N-m). Tighten self tapping screw (31) with bottom feed leg (make sure screw engages hole in leg). Refer to feed instructions packed with feed to assemble and install the feed assembly. *NOTE: Junction block (9) is packed with feed assembly. 1 2 3 ANTENNA BOTTOM FEED LEG HOLE MOUNT ASSEMBLY FIG. 2.0 - ASSEMBLING REFLECTOR TO AZ/EL CAP MOUNT S MOUNT TUBE MOUNT ASSEMBLY FIG. 2.1 - INSTALLING ANTENNA/MOUNT ASSEMBLY ONTO MOUNT TUBE CLAMP NUT 3

CLAMP SURFACE 12 11 13 9 14 6 5 6 4 8 6 9 7 7 15 10 Junction Block (9) FIG. 2.2 - INSTALLATION OF FEED AND FEED SUPPORT LEGS TO ANTENNA IMPORTANT: Sealing RF coaxial connector: The copper-plated center conductor in the RF coaxial cable, which connects receiver to LNB, can experience electrolysis corrosion at the LNB connector. Moisture and DC current cause this type of corrosion. To prevent corrosion, apply a moderate coat of silicon grease to the center conductor and then wrap the entire connection with COAX-SEAL tape to seal. (COAX-SEAL IS A REGISTERED TRADEMARK OF UNIVERSAL ELECTRONICS, INC.) GROUNDING *Coaxial Cable To Receiver *Ground Block NEC SECTION 810-20 ALL INSTALLATIONS TO CONFORM TO THE LATEST ISSUE OF THE NATIONAL ELECTRIC CODE. *Groundwire NEC SECTION 810-20 *Coaxial Cable From LNB *Items Not Supplied Ground pole, antenna mount assembly and feed cables must be grounded in accordance with current National Electric Code and local electric codes to protect from surges due to nearby lightning strikes. The illustration below illustrates a typical grounding method. FIG. 2.3 - GROUNDING FEED CABLES Clamps that provide a solid connection between ground wire and ground source should be used.

ANTENNA ALIGNMENT PROCEDURE Alignment with the satellite is obtained by setting polarization, elevation and azimuth. Charts 1, 2 & 3 are to determine the values for your earth station antenna site. L is the difference between the earth station antenna site longitude and the satellite longitude. Use L and your earth station latitude to obtain polarization, elevation or azimuth setting. POLARIZATION OF FEED Loosen feed horn M6 clamp bolts (12) and turn feed clockwise or counterclockwise, depending on being east or west of the satellite as shown on Chart 1. Align marks on the horn clamp and appropriate mark on the horn scale clamp is installed with arrow pointed toward antenna as shown in Fig. 3.0. Keep cable groove on header in the down position when adjusting polarization. NOTE: Single Polarity Feed is factory assembled for vertical polarity. If horizontal polarity is desired, rotate feed 90 (clockwise or counterclockwise). ELEVATION FEED ASSEMBLY FIG. 3.0 12 ALIGNMENT MARK -40 0 +40 FIG. 3.0 - POLARIZATION OF THE FEED ARROW To obtain elevation value for your satellite, refer to chart 2. Loosen bolts in curved slots of AZ/EL Housing ¹ ₈ to ¹ ₄ a turn (Ref. Fig. 3.1). Turn elevation adjustment bolt clockwise to decrease elevation and counterclockwise to increase elevation. Align the pointer with appropriate mark at the desired elevation reading (Ref. Fig. 3.1). NOTE: Degree values shown on elevation scale are Beam; that is when the antenna face is vertical mechanical elevation is 0, while the Beam Elevation (signal) is 22.6. This will be an approximate setting. Optimum setting achieved when fine tuning. Temporarily tighten elevation bracket nuts. AZIMUTH 20 30 0 10 20 30 40 50 60 70 ELEVATION ADJUSTING BOLT POINTER PIVOT BOLT AZ/EL HOUSING CLAMP BOLT Use Chart 3 and determine your azimuth setting. Values in chart must be adjusted for magnetic deviation for your location for correct compass reading. Rotate the antenna and mount, pointing it to the correct compass reading for your location and satellite (Ref. Fig. 3.2). Slowly sweep the antenna in azimuth until a signal is found. If the desired signal is not found, increase or decrease elevation setting and repeat the azimuth sweep. FIG. 3.1 - SETTING ANTENNA ELEVATION FINE TUNING Use a signal strength measuring device for final adjustments to obtain maximum antenna performance. Alternate between elevation and azimuth fine tuning to reach maximum signal strength until no improvement can be detected. Tighten all hardware. Torque for M8 round head, square neck bolts is 15 N-m (11 ft-lbs). FIG. 3.2 - ROTATING ANTENNA FOR AZIMUTH

POLARIZATION CHART " L" IS THE DIFFERENCE BETWEEN THE EARTH STATION ANTENNA SITE LONGITUDE AND THE SATELLITE LONGITUDE 90 POLARIZATION CHART SIGN VALUES (+ OR -) NORTHERN SOUTHERN HEMISPHERE HEMISPHERE ANTENNA SITE WEST OF SATELLITE LONGITUDE - + ANTENNA SITE EAST OF SATELLITE LONGITUDE + - 80 ANTENNA 70 + POLARIZATION + OR (SEE ILLUSTRATION) 60 50 40 30 20 30 40 60 Feed Rotation (Facing Antenna) 75 FEED For + Polarization, Rotate CCW (Counter Clockwis For - Polarization, Rotate CW (Clockwise) 15 20 10 10 5 0 0 10 20 30 40 50 60 70 80 EARTH STATION LATITUDE IN DEGREES NORTH OR SOUTH OF EQUATOR

ELEVATION CHART " L" IS THE DIFFERENCE BETWEEN THE EARTH STATION ANTENNA SITE LONGITUDE AND THE SATELLITE LONGITUDE 90 50 47.5 125 120 115 110 105 100 95 90 85 80 75 70 65 50 47.5 80 70 5 10 15 20 45 42.5 40 37.5 35 32.5 30 27.5 25 30 27.5 25 45 42.5 40 37.5 35 32.5 60 25 ELEVATION IN DEGREES 50 40 30 35 40 45 30 50 55 20 60 65 10 70 75 0 0 10 20 30 40 50 60 70 80 EARTH STATION LATITUDE IN DEGREES NORTH OR SOUTH OF EQUATOR CHART 2

AZIMUTH CHART " L" IS THE DIFFERENCE BETWEEN THE EARTH STATION ANTENNA SITE LONGITUDE AND THE SATELLITE LONGITUDE NORTHERN HEMISPHERE SOUTHERN HEMISPHERE EARTH STATION ANTENNA AZIMUTH (IN DEGREES) 180 190 200 210 220 230 240 250 260 180 170 160 150 140 130 120 110 90 75 70 65 55 60 30 35 40 45 50 0 5 10 15 20 25 0 10 20 30 40 50 60 70 80 360 350 340 330 320 310 300 290 280 270 270 90 270 EAST WEST 0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 WEST EAST EARTH STATION ANTENNA LATITUDE (IN DEGREES NORTH OR SOUTH OF EQUATOR) [AZIMUTH COLUMN READING WHEN EARTH STATION IS WEST OF SATELLITE] [AZIMUTH COLUMN READING WHEN EARTH STATION IS EAST OF SATELLITE] CHART 3

PARTS AND HARDWARE LISTING 2 1 3 16 17 18 19 3 26 17 2 25 19 2 20 3 23 24 21 3 23 2 17 22 FIG. 4.0 - AZ/EL CAP MOUNT ITEM PART NO. DESCRIPTION QTY. 1 2070022-01 BOLT-ROUND HEAD, SQUARE NECK M8X60 4 2 2603300-01 WASHER-LOCK M8 (⁵ ₁₆) 8 3 2460800-01 NUT-HEX M8 4 16 2010105-03 HOUSING AZ/EL 1 17 2503300-01 WASHER FLAT M8 (⁵ ₁₆) 5 18 2060006-01 BOLT-HEX M8 x 130 1 19 2070022-03 BOLT-ROUND HEAD, SQUARE NECK M8 x 20 3 20 2070022-05 BOLT-ROUND HEAD, SQUARE NECK M8 X 35, MO. 6031 3 21 2020343-02 CLAMP-WELDMENT, 2³ ₈ O.D. 1 21 2020322-02 CLAMP-WELDMENT, 3 O.D. 1 22 1010047-01 PAD - ABRASIVE 1 23 2380075-01 NUT-ELASTIC STOP M8, MO. 6031 4 24 2380067-02 NUT-SWIVEL/SPECIAL 1 25 2010119-01 POINTER 1 26 2509002-01 WASHER-SPHERICAL 1 6010213-01 MOUNT ASSY. 2³ ₈ O.D. 6010017-01 MOUNT ASSY. 3 O.D.

PARTS AND HARDWARE LISTING CLAMP SURFACE 12 11 13 9 14 6 5 6 4 8 6 9 7 7 15 10 Junction Block (9) FIG. 4.1 - ANTENNA, ANTENNA FEED (LNB) & FEED SUPPORT LEGS ITEM PART NO. DESCRIPTION QTY. 4 2020329-07 LEG BOTTOM (.90m) 1 4 2020329-02 LEG-BOTTOM-FEED (1.0m) 1 4 2020329-03 LEG-BOTTOM-FEED (1.2m) 1 5 3040642-02 REFLECTOR-SMC-1.0m 1 5 3040646-02 REFLECTOR-SMC-1.2m 1 5 3040681-02 REFLECTOR-SMC.90m 1 6 6010100-05 LEG-SIDE-FEED (1.0m) 2 6 6010100-06 LEG-SIDE-FEED (1.2m) 2 6 6010100-07 LEG-SIDE-FEED (.90m) 2 7 2060008-01 BOLT-HEX M6 x 30 4 8 2509010-01 WASHER, FLAT ¹ ₄ x ⁷ ₈ 2 9* 3040667-04 BLOCK-JUNCTION 1 10 2502700-01 WASHER-FLAT ¹ ₄ x ³ ₄ O.D. 2 11* 3040663-01 CLAMP-HALF-JCT. 1 12* 2050610-20 BOLT HH M6 x 20 2 13* 2480600-01 WASHER-FLAT M6 x ¹ ₂ O.D. 2 14* VARIES KU-FEED ASSY. 1 15 2060009-01 SCREW-TPG-SPL M6 1 *Provided in feed assembly.

HARDWARE SORTER M8 x 60mm Round Head Square Neck Bolt Item 1, PN 2070022-01 M6 Tapping Screw Item 15, PN 2060009 M6 x 30mm Hex Head Bolt Item 7, PN 2060008 M8 x 20mm Round Head Square Neck Bolt Item 19, PN 20700022-03 M4 x 12mm Phillips Head Screw PN 2430070-04 M8 x 35mm Round Head Square Neck Bolt Item 20, PN 2070022-05 M4 x 10mm Phillips Head Screw PN 2430070 Washer, Flat - ¹ ₄" x ³ ₄" OD Item 10, PN 2502700-01 Washer, Flat - ¹ ₄" x ⁷ ₈" OD Item 8, PN 2509010-01 Hardware illustrations are true size. Place actual hardware on top of illustration to identify.