6004 wall-mounted desk bdiusa.com customerservice@bdiusa.com Component List H - 4mm Hex Wrench x 1 H2-3mm Hex Wrench x 1 I -Toggle nchor Kit x 2 - Washer x 6 K - Wood Screw x 4 roduct Registration Registering your new BDI product allows us to send you important product updates, service information and helpful hints related to your BDI products. Register today, and you will be entered to win free a BIK table from BDI: www.bdiusa.com/register lacement and Maintenance Sequel Office Furniture is designed for indoor use. Clean glass with glass cleaner, and steel parts and wood veneer with a moist cloth. Your Sequel Home Office Furniture is engineered for easy assembly. Carefully follow this procedure to prevent any damage. Do not use power tools for assembly of this product. TWO ERSO SSEMBLY L - Drywall nchor x 2 M - Drywall Screw x 2 - Set Screw x 4 O - dhesive Dot x 4 Step 1 Unpack and identify the parts listed below. The assembly workspace should be a non-marring surface such as carpet. For missing hardware pieces, please contact BDI Customer Service at customerservice@ bdiusa.com. For all other concerns, please contact your BDI Retailer. - 1/4-20 x 38 mm Screw x 4 Q - 1/4-20 x 12 mm Screw x 4 G - Wire Management Lid x 1 F - Top Glass x 1 R - 1/4-20 x 6mm Screw x 4 S - Kick anel Stop x 2 - Wall ttachment Rail x 1 CR - Right Desk Side x 1 T - ower Strip Bay x 1 U - dhesive Bumper x 2 V - Drawer Liner x 1 B - Drawer ssembly x 1 W -1/4-20 x 58mm Screw x 3 E - Kick anel x 1 X - dhesive Foam/Magnet x 2 D - Wire Management Trough x 1 Designed by Matthew Weatherly. These distinctive product configurations are protected by US and international patents, trade dress, and/or copyright laws. Sequel and BDI are trademarks of Becker Designed, Inc. ll Rights reserved. 2014 Becker Designed, Inc. Made in Taiwan. 6004REV052416v4 CL - Left Desk Side x 1 1
Step 2 - The desk can be mounted at any height desired. For a sitting desk at 29 H, mark the center of the desk in its desired location 24.75 in/63 cm from the floor. For a standing desk, measure and mark 4.25 in/10.8 cm from the bottom of your elbow at a 90º position. The top of the desk will be 4.25 above the bottom of the Wall ttachment Rail. Sitting 24.75 in/ 63 cm Standing 4.25 in/ 10.8 cm Step 3 - lign the bottom of the Wall ttachment Rail () to the marked line and level. While holding the leveled Wall ttachment Rail (), allow the second person to outline the holes on the Wall ttachment Rail () and mark within each outline. TWO ERSO SSEMBLY 6004 WLL-MOUTED DESK 2
Step 4 - Determine which wall attachment method below is needed to attach Wall ttachment Rail () to the wall at each of the marks from the previous step. Follow instructions included in the Toggle nchor Kit (I) for proper installation of Toggle nchors. If installing into a masonry wall, please contact your local hardware store for preferred method of attachment. I I-S Sheet Rock: (I) Toggle nchor () Wall ttachment Rail (I-S) Toggle nchor Screw () Washer K Wooden Stud: () Wall ttacment Rail (K) Wood Screw () Washer Step 5 - Install Set Screws () into threaded holes of Wall ttachment Rail () using Hex Wrench (H2). 6004 WLL-MOUTED DESK 3
Step 6 - With the Drawer ssembly (B) upside down, attach Desk Sides (CL, CR) with Screw () using Hex Wrench (H). pply dhesive Dots (O) to the back edge of Desk Sides (CL, CR) at the top and bottom. CL O O O CL CR B O O Step 7 - Confirm that the attached Desk Sides (CL, CR) are flush with the Drawer ssembly (B). Incorrect lignment 6004 WLL-MOUTED DESK 4 Correct lignment
Step 8 - With the help of another person, carefully lower Wire Management Trough (D) between the Desk Sides (CL, CR) and align holes. ttach Wire Management Trough (D) to Desk Sides (CL, CR) with Screw (Q) using Hex Wrench (H). TWO ERSO SSEMBLY D D CR CR Q CL Q Step 9 - ttach Kick anel Stops (S) to the back holes of Drawer ssembly (B) using Screw (R) and Hex Wrench (H). B R S B 6004 WLL-MOUTED DESK 5
Step 10 - pply dhesive Bumpers (U) to the bottom of the back side of ower Strip Bay (T). U T U Step 11 - Secure ower Strip Bay (T) to Wall ttachment Rail () using Screw (R) and Hex Wrench (H). R R T 6004 WLL-MOUTED DESK 6
Step 12 - With the help of another person gently lower the Desk ssembly onto the Wall ttachment Rail (). Ensure the hooks of the Desk ssembly are fully engaged with the Wall ttachment Rail () before releasing the assembly. TWO ERSO SSEMBLY Step 13 - Center the Desk ssembly within the Wall ttachment Rail () using the indentations in the Wall ttachment Rail () as a guide. indentation 6004 WLL-MOUTED DESK 7
Step 14 - Using Hex Wrench (H), adjust Set Screws () on Wall ttachment Rail () to create a level work surface that is flush against wall before moving to Step 15. Down Up In Out Step 15 - Duplicate the wall attachment method used on the outermost screws from Step 3 for attaching Wire Management Trough (D) to the wall. If Toggle nchors were used on Step 3, use standard Drywall nchors (L) for this step. ttach Wire Management Trough (D) to wall using Screw and Washer () combination. DO OT OVERTIGHTE! B D D 6004 WLL-MOUTED DESK 8
Step 16 - With the help of another person gently lower Top Glass (F) onto Drawer ssembly (B) and fasten into place using Screw (W) and Hex Wrench (H). With the grippy side facing down, insert Drawer Liner (V) into drawer body. TWO ERSO SSEMBLY F re-installed Rubber Bumper B W W W V x 1 W x 3 re-installed Rubber Bumper 6004 WLL-MOUTED DESK 9
Step 17 (Optional) - Remove dhesive Foam/Magnets (X) from the ower Strip Bay (T). eel film from side of the dhesive Foam/Magnets (X) and attach to clean, dry back side of C power strip (not included). Cleaning of power strip surface with rubbing alcohol will ensure best adhesive bond. **ULUG OWER STRI FROM OWER SOUCE BEFORE CLEIG** ttach C power strip/surge protector (not included) on platform of ower Strip Bay (T) as shown in illustration below. 1. Use the slot holes provided to run all wire to and from the desk. Keep all wire behind the folded metal lips. Failure to do so will prevent Kick anel (E) from attaching properly. 3. 2. X X * C ower Strip ot Included T 6004 WLL-MOUTED DESK 10
Step 18 - Once all the electrical wire are routed, install Kick anel (E) as shown below. The rear side of the panel has magnets that will hold it into place. lace Wire Management Lid (G) into opening of Top Glass (F). G F E 6004 WLL-MOUTED DESK 11