FEATURES Progrmmle output voltge (0%~05%) Progrmmle output current (0%~05%) Universl AC input / Full rnge Constnt current limiting Optionl glol control vi RS3 Selectle +5V / 0.5A or +9V / 0.3A uxiliry output Forced current shring t prllel opertion Power OK signl Optionl remote setting multiple PSU vi RS3, RS485 & I²C Remote ON/OFF, Remote sense function SPECIFICATION Input Voltge Rnge: 90~64VAC, 7-370VDC (Note 4) Input Frequency: 47~63Hz Power Fctor: 30VAC / 0.95, 5VAC / 0.98 t full lod Input AC Current: 9.3A / 00VAC, 3.7A / 30VAC Inrush Current: 30A / 5VAC, 60A / 30VAC Lekge Current: Less thn.0ma / 40VAC Over Lod Protection: 05% rted output power Protection Type: Constnt current limit Over Voltge Protection: Vrile OVP, 0 ±7% Vout. Protection type: Ltch-style (Recovery fter reset AC power ON or inhiit); Refer to VS OVP curve. Over Temperture Protection: 85 ± 5 C detect on NTC Protection type: Auto recovery fter temperture goes down. Auxiliry Power: Selectle +5V / 0.5A or +9V / 0.3A uxiliry output Remote ON/OFF Control: By externl switch Power OK Signl: Open drin signl low when PSU turns on. Mx. sink current: 0mA; Mx. drin voltge: 40V Output Voltge Trim: Adjustment of output voltge is etween 0~05% of rted output. Output Current Trim: Adjustment of output current is etween 0~05% of rted output. Prllel Current Shring: Plese refer to pge 6 (Note 5) Address Setting: Up to 8 units cn e set using n ddress switch (sw), 0~7. Working Temperture: -0 ~ +60 C (Refer to de-rting curve) Working Humidity: 0 ~ 90% RH non-condensing Voltge Adjustment Rnge: ±5% typicl djustment y potentiometer (VR) Voltge Tolernce: Lod Regultion: ±.0% Line Regultion: ±.0% Hold-up time: 4ms / 30VAC t full lod Set-up, Rise-time: 800ms, 00ms t full lod Storge Temperture Humidity: -40 ~ +85 C, 0 ~ 95% RH Temperture Coefficient: ±0.0% / C (0~50 C) Virtion: 0 ~ 500Hz, G 0min. / cycle, period for 60min ech long X, Y, Z xes. Complince to IEC68--6, IEC 68--64 Sfety Stndrds: UL 60950-, EN60950- Withstnd Voltge: I/P-O/P: 3KVAC (44DC); I/P-FG:.5KVAC (CD); O/P-FG: 0.5KVAC (707DC) (Note 7) Isoltion Resistnce: I/P-O/P, I/P-FG, O/P-FG: 00MOhm / 500VDC EMI Conduction & Rdition: Certified EN550, EN604-3, EN6000-6-3 Hrmonic Current: Certified EN6000-3-, EN6000-3-3 EMS Immunity: Certified EN5504, EN604-3, EN6000-6- IEC 6000-4-, 3, 4, 5, 6, 8, Cooling: Lod nd temperture control fn Wrrnty: 4 months ±.0% (Note 3)
Output Voltge / Current Rting Chrt: Mesured t output power connection Model Input Voltge Output Voltge Rted Power Rted Current Efficiency Mx. Ripple & Noise (Note ) AE800-90~64VAC V 800W 66.7A 89% 0mVp-p AE800-5 90~64VAC 5V 80W 53.4A 90% 50mVp-p AE800-4 90~64VAC 4V 804W 33.5A 9% 40mVp-p AE800-30 90~64VAC 30V 80W 6.7A 9% 300mVp-p AE800-36 90~64VAC 36V 80.8W.3A 9% 360mVp-p AE800-48 90~64VAC 48V 80.6W 6.7A 9% 480mVp-p AE800-60 90~64VAC 60V 804W 3.4A 93% 600mVp-p Note ) All prmeters NOT specilly mentioned re mesured t 30VAC input, rted lod nd 5 C of mient temperture. Note ) Ripple & noise re mesured t 0MHz of ndwidth y using " twisted pir-wire terminted with 0.uf & 47uf prllel cpcitor. Note 3) Tolernce includes setup time tolernce, line regultion nd lod regultion. Note 4) De-rting my pply in low input voltge. Plese check the de-rting curve for more detils. Note 5) In prllel connection, only one unit operte if the totl output lod is less thn 5% of rted lod condition. Note 6) The power supply is intended for instlltion s component of system. The finl equipment must e re-confirmed tht it still meets EMC directives. Note 7) This test is done without enclosure.
Mechnicl Specifictions: 49(L) x 7(W) x 4(H)mm;.7kg 4[.64] 3-M4 L=4[0.57] CN Address Switch 3 CN 4 6 8 0 4 6 8 0 4 3 5 7 9 3 5 7 9 6-M4(Both Sides) L=6[0.36] AC Input Terminl Pin No. Assignment Pin No. 3 Assignment ACL ACN Function Description Pin No. 3 4 5 6 7 8 9 0 Function Description Pin No. Function Description Remote sense (+) Positive output voltge Remote sense (-) Negtive output voltge Power OK Prllel opertion current shre Aux output setting Inhiit ON/OFF (-) Inhiit ON/OFF (+) +5V / 0.5A or +9V / 0.3A Auxiliry power 3 4 5 6 7 8 9 0 3 4.. I Progrm V Progrm +5V / 0.5A or +9V / 0.3A Auxiliry power Seril Clock used in the I C interfce Seril Dt used in the I C interfce +5V / 0.5A or +9V / 0.3A Auxiliry power For RS3 Trnsmission function For RS3 Receiver function Mting Housing / Contct JST PHDR-4VS or equivlent JST SPHD-00T-P0.5 or equivlent
LED Sttus Solid(Green) Solid(Ornge) Slow Blink(Green) Fst Blink(Red) Solid(Red) Slow Blink(Red) LED LED Signl Sttus Intermittent Blink(Red) Interlce Blink(Red) Power OK (Locl mode) Power OK (Remote mode) Power Stndy Over Voltge Protection ( OVP ) Over Lod Protection ( OLP ) Over Temperture Protection ( OTP ) Fn Filure Power Filure De-rting Curve Lod V.S Temp. Lod V.S I/P Voltge T=5 C Lod (%) 00 80 60 50 40 0 Lod (%) 00 90 80 70 60 50 40-0 0 0 0 30 40 50 60 70 Amient Temperture ( C) CMD VS Output Curve 90 00 0 0 64 Input Voltge (Vc) VS OVP Curve OVP 00% 96% 0% 4% V K 0.5V 0.75V 4.5V 4.8V 0.75V (Output 6.5%) 4.5V (Output 00%) CN 3 4 Exteml Voltge VDC CN 3 4 Exteml Resistor KÙ I. II. III. CTRL IC ma I-Shrink MIN ma / A/D PWM IC ma IC ma 0R CTRL / CTRL 0~5Vdc / Power Supply Power Supply Power Supply VC=IC. R R=5K
Remote ON/OFF (A) Defult Setting (B) (C) KÙ SW OFF Power OFF sw ON Power ON (A) Using internl 5V uxiliry source KÙ Power Supply Power Supply Power Supply Ctrl (B) ON / OFF Control y NPN trnsistor Tr L H Ctrl Power OFF Power ON KÙ SW OFF Power OFF sw ON Power ON (C) Using externl voltge source Externl DC source (MAX=9V dc) Power OK Signl * The grounding of "" power should e connected to "" port. If " V-" is connected s ing, mke sure to short the nd V- ports. *Plce n dditionl cpcitor to hve etter performnce of uxiliry power opertion. Open(Defult Setting) 5V Short To 9V 470 F 6V. LOAD DC / DC 5V/0.5A or 9V/0.3A nd P.OK Signl. Remote Sense. Locl Sense (Defult setting) Lod 3 CN 4 3 CN 4 Lod, Compenstion Voltge < 0.5V
3. Current Shring with Remote Sensing(Prllel Connection) 3 4 3 4 3 4 3 4 4. Current Shring with Locl Sensing 3 4 3 4 3 4 3 4
800W PFC INDUSTRIALPOWER SUPPLY Instlltion Instructions. Mounting Directions - Recommended stndrd mounting methods () () 3-M4 L=4[0.57] 3-M4 L=4[0.57] 3-M4 L=4[0.57]. Mounting Method - There re ventilting holes on the front nd ck side pnels, do not ostruct; llow 50mm t lest for ir flow. - Recommended the torque of mounting screw: M4 screw:.7n m (3.0kgf cm) More thn 50mm More thn 50mm FAN Air flow FAN
GERMANY Johnn-Friedrich-Boettger-Str. 633 Roedermrk Phone: +49 6074 6985-0 Fx: +49 6074 6985-0 E-Mil: sles.de@hitekpower.com Revision 08/04