1 OF 6
Component Parts A Fixture Pipe (3) B Coupling (3) C Canopy Pipe (3) D Middle Canopy Can E Clutch (3) F Plastic Sleeve (3) G Side Canopy Can (2) H Set Screw (3) I Middle Crossbar J #10 Screws (4) K Outer Mounting Plates (2) L Short Threaded Studs (4) M Long Threaded Studs (2) O P Fixture # 8 Screw Safety Cable Q Barrel Knobs (6) R Half Round Couplings (3) S Side Glass Cover (2) T U Middle Glass Cover Small Glass Globe V Side Plate (2) W Large Glass Globe X Accent Swoops (7) Y Hooks with otches (14) Z Anchors 2 OF 6
CAUTIO: FAILURE TO ISTALL THIS FIXTURE PROPERLY MAY RESULT I SERIOUS PERSOAL IJURY OR DEATH AD PROPERTY DAMAGE. We recommend installation by a licensed electrician. This product must be installed in accordance with applicable installation code(s), by a person familiar with the construction and operation of the product and the hazards involved.* Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture. Please ote: After installation extra hardware and accessories are possible due to our kits being used on multiple products and options. To Assemble Fixture (Figures 1, 2 & 3) CAUTIO: BE SURE POWER IS OFF AT THE MAI BREAKER BOX PRIOR TO ISTALLATIO. 1. Carefully unpack fixture from carton. 2. Slip fixture pipe (A) unpainted threads end first over any of the 3 sets of wires. 3. Apply a drop of the supplied thread locking compound to the threads of fixture pipe (A) and screw into coupling (B), being careful not to twist or pinch the wires. ote: Application of the thread locking compound is necessary to prevent the pipe from loosening during regular maintenance and cleaning of the fixture. Be certain to apply the compound. 4. Repeat steps 2 & 3 for the two remaining fixture pipes (A). 5. Run the wires from the center fixture pipe (A) through the canopy pipe (C) attached to the middle canopy can (D). 6. Unscrew the clutch (E) from the canopy pipe (C); slide it across the wires and onto the fixture pipe (A). Follow this with the plastic sleeve (F), oriented so the tapered end nests in the clutch (E) (Figure 2). 7. Repeat steps 5 & 6 for the side canopy cans (G) and the two remaining fixture pipes (A). 8. Slide the canopy pipe (C) as far as necessary to achieve the total height of fixture desired. Be careful not to scratch the pipe surfaces and to pull excess wire up through the canopy pipe (C). There must be a minimum 1-1/2" of inner pipe inside the outer pipe. Screw clutch (E) onto canopy pipe (C). Tighten the set screw (H) firmly with hex wrench provided. 9. Repeat this for the two remaining canopy pipes (C) being sure to keep the notches in the swivels facing the same direction (Figure 3). 10. Follow steps on following page to make wiring connections. Yeah, you got this! 3 OF 6
To Make Wiring Connections (Figures 1, 2 & 3) 1. Making sure to keep the two outside mounting plates (K) in the orientation desired and the middle crossbar (I) over the electric box, mark the location of all the anchors (Z) on the ceiling. Set the crossbar aside. 2. Drill 1/4 holes in the locations marked on the ceiling. Place the tapered ends of all anchors (Z) into the holes and gently tap flush with a hammer. 3. Using two machine screws (not provided), attach the middle crossbar (I) to the electric box. ote: A new electric box comes with screws. When replacing a fixture, retain the existing screws for use with the new fixture. 4. Thread the #10 screws through the outside mounting plates (K) and into the anchors (Z) to secure the outside mounting plates (K) to the ceiling. Be careful not to over tighten or strip the anchors. 5. Thread the short threaded studs (L) into the outer mounting plates (K). Thread the long threaded studs (M) into the middle crossbar (I). 6. Raise the fixture () to the ceiling and using one of the #8 screws (O) found in the kitbag attach the safety cable (P) to the middle crossbar (I) and suspend the fixture Caution: The cable is intended to temporarily suspend the fixture while wiring connections are made. ever depend on it to support weight with the fixture installed. 7. Run the black, white, and green ground wires from each side canopy can (G) through the square tube toward the middle crossbar (I). 8. Slide the side canopy can (G) over the short threaded studs (L) and secure to the outside mounting plate (K) with barrel knobs (Q). Be sure barrel knobs (Q) are fully seated onto the short threaded studs (L). 9. Repeat this for the second side canopy can (G) on the opposite outside mounting plate (K) making sure to keep the notches in the swivel facing the same direction as the other swivel. 10. Using suitable wire connectors (not provided), connect the fixture wires from all three cans to supply wires (white to white supply, black to black supply). Connect all ground wires (bare copper or green to bare copper or green). Push wires back into outlet box. Be sure to leave slack in the wires to allow for final height adjustments. Caution: Make sure wire connectors are twisted on securely, and no bare wire is exposed. 11. Slide middle canopy can (D) over long threaded studs (M) until flush against the ceiling and secure with barrel knobs (Q). Make sure no wires are pinched between the can and the ceiling. 12. Small adjustments in height may be made at this time by loosening the set screw (H) and clutch (E). Be sure to retighten after adjusting. 13. Install a bulb (not included) in each socket. ote: Using a slightly higher wattage bulb in the middle socket will make the fixture light more evenly 14. Follow instructions on page 6 to complete installation. 4 OF 6
MACHIE SCREWS Z I O P M D K J L G Q (Figure 1) C F H E A B (Figure 2) (Figure 3) 5 OF 6
To Complete Installation (Figure 4) 1. Loosen all 3 of the half round couplings (R) fully to allow the side glass covers (S) and middle glass cover (T) to be raised up. 2. While holding the side glass cover (S) up, slide the small globe glass (U) over the side plate (V) until the small globe glass is centered on the side plate (V). 3. When the small globe glass (U) is centered, allow side glass cover (S) to cover the opening in the top of glass. Retighten the half round coupling (R) to secure the small glass globe (U). ote: Tighten half round couplings (R) until snug. Overtightening can cause the glass to crack. 4. Repeat this step for the other small globe glass (U) and side glass cover (S) and the large glass globe (W) and the middle glass cover (T). 5. When all 3 glass globes have been secured follow the orientation in figure 4 to install all of the accent swoops (X). 6. Accent plates (X) all have hooks with notches (Y) that loop over and rest in the notch (AA) on fixture (). ote: The accent swoops (X) will only fit in the orientaion show in figure 4. 7. Restore electricity at main breaker. (Figure 4) R T Y W R S V U AA R S X (Figure 5) If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased this product. We hope you enjoy your fixture! * Vermont Modern / Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture. 6 OF 6