RIXSON ASSA ALOY Template 3/4 1/8 2- R. Max 1-7/16 1-1/32 2-2-3/4 7/8 Dia. C L Spindle Installation Instructions 3040 (05-09) 9/16 9/32 1/16 Finish Plate 1/4 1-1/4 Dia. 340 TOP PIVOT PIVOT SHOWN ENGAGED Checking Adjustments Floor Plate 1/4-20 x " FHMS or #14 x 1/2" FHWS 15/32 21/32 30-40 Floor Closer Center Hung Double Acting Non-Handed 6-3/4 1-15/32 9/32 JAM PORTION 9/32 1-5/16 12-24 x " FHMS or 9/32 #12 x 1-1/4" FHWS (2 Places) 1/4-20 x " FHMS or 1-1/8 #14 x 1-1/2" FHWS DOOR PORTION (2 Places) 4-1 5-9/32 1-9/16" Min. Clearance Required for, Plate and Shims Floor Plate Mortised 1-9/16 Deep for 7/8 1-1/4 Provide 3/8" Dia. Hole 1-9/16 Floor Plate 1/4 Threshold 1/2 Threshold 1/8 2- "" 1-1/16 15/16 11/16 F Plate H D 7-7/16 1-9/16 Dia. Spindle Shoulder Collar C Cement Case 7/16 With Threshold Use Top (2) Holes With Floor Plate Use ottom (2) Holes E Cement Case A WITH FLOOR PLATE Set Cement Case 1/8" elow Surface of Finished Floor Provide " dia. hole for alignment screw. Mortised "A" Deep for "A" Mortised 1-9/16 Deep 1/4 Threshold 1-1/8 for 1/2 Threshold 7/8 Threshold Closer Number 30 A 5-3/8 Dimensions C 5-1/2 14-9/16 D 15-1/8 E 3- F 2-5/16 WITH THRESHOLD Set Cement Case Flush with Finished Floor 40 6-1/16 6-1/8 17 Conversion from inches to metric: inch x 25.4. Suitable reinforcing by others. Rixson designed threshold available on request. Auxiliary stop required. Rixson Specialty Controls 17-1/4 4-1/16 2-9/16 www.rixson.com 1/4-20 x 1" FHMS or #14 x 2" FWHS (4 Places) 1-1/4 1-19/32 2-3/32 C L Spindle 1-25/32 1-7/32 11/32 3-1 ARM PLATE H 29/32 1-13/32 866-474-9766 Technical Department
PAGE 2 How To Determine Hand of LH RH Top Pivot Portion Top Pivot Portion Adjusting Screw IMPORTANT: Use plumb line to make sure that center line of top pivot pin lines up with center line of closer spindle. Plate H Alignment Screws Face a door swinging open away from you. If it opens to the right, it is right hand. If it opens to the left, it is left hand. NOTE: This product allows door to swing in both directions. Installation Instructions 1. Locating Closer Spindle Position Centerline of and Spindle A. Measure 2-3/4 out from door jamb on centerline of door. This is the location of the spindle center. 2-3/4 From Face of to C of Spindle L 2. Install Cement Case in Floor LEVEL IN OTH DIRECTIONS A. For floor plate application: Cement case is set 1/8 (3.2mm) below floor level.. For threshold application: Cement case is set flush with floor. C. Set cement case in floor and block in position. D. Case should be parallel with center line of door. E. CEMENT CASE SHOULD E LEVEL. Place levels per Illustration. F. Grout in cement case with closer. Cement should not get between closer and case.
3. Install Pivot and Closer PAGE 3 DOOR A. Install top pivot in door per template.. Install top pivot in jamb per template. Spindle Shims (for threshold use only) Plate H Closer in Floor C. Centerline of pivot pin should line up with centerline of spindle. Use plumb line to assure accuracy. D. Mortise door for arm, arm plate H. E. Drill two dia. holes for arm alignment screws. Drill 3/8 hole at heel edge of door for adjusting screw. F. Install arm, arm plate H, and shims if required. (If 1/2 threshold is used install 4 shims above arm plate H refer to template. If 1/4 threshold is used install (2) 1/16 shims above plate H ). Attach arm alignment screws and washers to hold arm in place. 4. Hang Top Pivot Pin Centerline of 30 Pin Retracting Screw CAUTION: Closer is shipped with "valve" screws down. DO NOT FORCE VALVE DOWN. A. Retract top pivot pin by turning retracting pin screw counter-clockwise (see illustration).. With arm on spindle, turn spindle until arm is in 30 open position (see illustration). C. Set door on spindle arm. DO NOT ATTEMPT TO CLOSE DOOR. D. Align two portions of top pivot and turn pin retracting screw clockwise to engage top pivot pin. E. Open door to 60 or more and turn valve screws counterclockwise. will then close. F. If necessary, turn adjusting screw at bottom of heel edge of door to equalize side jamb clearances. Adjusting Screw G. Adjust arm alignment screws equally from each side to center door in doorway. Alignment Screws
Closer Adjustment PAGE 4 Closing speeds can be adjusted to suit local conditions and requirements. Label on closer face designates the purpose of each adjustment screw. Adjustments are for speed control. Closer Type This closer is one of three types as follows: 1. Non hold-open factory set. No hold-open adjustments. 2. Automatic hold-open factory set. No hold-open adjustment. Spring Power Adjustments This closer can be adjusted for increased or decreased spring power. These adjustments if required should be done by an authorized repair agency. Repairs, parts replacement or internal adjustments must be done by a Rixson authorized repair agency. Consult www.rixsondoorcontrols.com for an authorized repair agency in your area. Rixson is a registered trademark of Yale Security Inc., an ASSA ALOY Group company. Copyright 2002, 2009, Yale Security Inc., an ASSA ALOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. RIXSON ASSA ALOY
RIXSON ASSA ALOY Template 3/4 1/8 2- R. Max 1-7/16 1-1/32 2-2-3/4 7/8 Dia. C L Spindle Installation Instructions 3040W (05-09) 9/16 9/32 1/16 Finish Plate 1/4 1-1/4 Dia. 340 TOP PIVOT PIVOT SHOWN ENGAGED Checking Adjustments Floor Plate 1/4-20 x " FHMS or #14 x 1/2" FHWS 15/32 21/32 W30-W40 Floor Closer Center Hung Double Acting Non-Handed Wood Installation 6-3/4 1-15/32 9/32 JAM PORTION 9/32 1-5/16 12-24 x " FHMS or 9/32 #12 x 1-1/4" FHWS (2 Places) 1/4-20 x " FHMS or 1-1/8 #14 x 1-1/2" FHWS DOOR PORTION (2 Places) 4-1 5-9/32 1-3/8 Min. Clearance Required for, Plate and Shims Floor Plate Mortised 1-7/8 Deep for 1-1/4 1-1/4 1/8 2-7-7/16 2-1/4 9 Mortised Provide Shim 3/8" Dia. Plate H Hole 1-7/16 Floor Plate 1/4 Threshold 1/2 Threshold "" 1-1/16 15/16 11/16 D 1-9/16 Dia. Spindle Shoulder Collar Cement Case 7/16 Wood Plate Use Top (2) Holes E Cement Case A WITH FLOOR PLATE Set Cement Case 1/8" elow Surface of Finished Floor Provide 9/16 dia. hole for alignment screw. Mortised "A" Deep for Closer Number 30 A 5-3/8 F Dimensions C 5-1/2 14-9/16 C D 15-1/8 E 3- F 2-5/16 "A" " 1/4 Threshold 1-3/4 1-1/8 1/2 Threshold 1-1/2 7/8 WITH THRESHOLD Set Cement Case Flush with Finished Floor Threshold 40 6-1/16 6-1/8 17 17-1/4 4-1/16 2-9/16 C L Spindle WOOD DOOR ARM PLATE Conversion from inches to metric: inch x 25.4. Suitable reinforcing by others. Rixson designed threshold available on request. Auxiliary stop required. 2-3/32 4-7/32 1-25/32 1-7/32 9/32 9/16 1-19/32 1-13/32 6-7/32 10-1/2 Holes for (6) 2-1/2-14 FHWS 11/16 C L 1-3/8
PAGE 2 How To Determine Hand of LH RH Top Pivot Portion Top Pivot Portion Adjusting Screw IMPORTANT: Use plumb line to make sure that center line of top pivot pin lines up with center line of closer spindle. Wood Plate Face a door swinging open away from you. If it opens to the right, it is right hand. If it opens to the left, it is left hand. NOTE: This product allows the door to swing in both directions. Shim Plate H Alignment Screws Installation Instructions 1. Locating Closer Spindle Position Centerline of and Spindle A. Measure 2-3/4 out from door jamb on centerline of door. This is the location of the spindle center. 2-3/4 From Face of to C of Spindle L 2. Install Cement Case in Floor LEVEL IN OTH DIRECTIONS A. For floor plate application: Cement case is set 1/8 (3.2mm) below floor level.. For threshold application: Cement case is set flush with floor. C. Set cement case in floor and block in position. D. Case should be parallel with center line of door. E. CEMENT CASE SHOULD E LEVEL. Place levels per Illustration. F. Grout in cement case with closer. Cement should not get between closer and case.
3. Install Pivot and Closer PAGE 3 DOOR Shim Wood Plate A. Install top pivot in door per template.. Install top pivot in jamb per template. C. Centerline of pivot pin should line up with centerline of spindle. Use plumb line to assure accuracy. Spindle Plate H Closer in Floor D. Mortise door for arm and arm plates. Install arm plate, shim, and arm. (If threshold is used, refer to template). E. Drill two 9/16 dia. holes for arm alignment screws. Drill 3/8 hole at heel edge of door for adjusting screw. 4. Hang Top Pivot Pin Centerline of 30 Pin Retracting Screw CAUTION: Closer is shipped with "valve" screws down. DO NOT FORCE VALVE DOWN. A. Retract top pivot pin by turning retracting pin screw counter-clockwise (see illustration).. With arm on spindle, turn spindle until arm is in 30 open position (see illustration). C. Set door on spindle. DO NOT ATTEMPT TO CLOSE DOOR. D. Align two portions of top pivot and turn pin retracting screw clockwise to engage top pivot pin. E. Open door to 60 or more and turn valve screws counterclockwise. will then close. F. If necessary, turn adjusting screw at bottom of heel edge of door to equalize side jamb clearances. Adjusting Screw G. Adjust arm alignment screws equally from each side to center door in doorway. Alignment Screws
Closer Adjustment PAGE 4 Closing speeds can be adjusted to suit local conditions and requirements. Label on closer face designates the purpose of each adjustment screw. Adjustments are for speed control. Closer Type This closer is one of three types as follows: 1. Non hold-open factory set. No hold-open adjustments. 2. Automatic hold-open factory set. No hold-open adjustment. Spring Power Adjustments This closer can be adjusted for increased or decreased spring power. These adjustments if required should be done by an authorized repair agency. Repairs, parts replacement or internal adjustments must be done by a Rixson authorized repair agency. Consult www.rixsondoorcontrols.com for an authorized repair agency in your area. Rixson is a registered trademark of Yale Security Inc., an ASSA ALOY Group company. Copyright 2002, 2009, Yale Security Inc., an ASSA ALOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. RIXSON ASSA ALOY