DRIVER INFORMTION & MULTIMEDI SECTION V UDIO, VISUL & NVIGTION SYSTEM C D CONTENTS E SE UDIO Symptom Table...24 F SIC INSPECTION... 5 DIGNOSIS ND REPIR WORKFLOW... 5 Work Flow...5 FUNCTION DIGNOSIS... 7 UDIO SYSTEM... 7 System Diagram...7 System Description...7 Component Parts Location...8 Component Description...8 COMPONENT DIGNOSIS... 9 POWER SUPPLY ND GROUND CIRCUIT... 9 UDIO UNIT...9 UDIO UNIT : Diagnosis Procedure...9 FRONT DOOR SPEKER...10 Description...10 Diagnosis Procedure...10 FRONT TWEETER...12 Description...12 Diagnosis Procedure...12 RER DOOR SPEKER...14 Description...14 Diagnosis Procedure...14 ECU DIGNOSIS...16 UDIO UNIT...16 Reference Value...16 Wiring Diagram...18 SYMPTOM DIGNOSIS...24 UDIO SYSTEM...24 NORML OPERTING CONDITION...25 Description...25 PRECUTION...26 PRECUTIONS...26 Precaution for Supplemental Restraint System (SRS) "IR G" and "SET ELT PRE-TEN- SIONER"...26 PREPRTION...27 PREPRTION...27 Commercial Service Tools...27 ON-VEHICLE REPIR...28 UDIO UNIT...28 Removal and Installation...28 FRONT TWEETER...29 Removal and Installation...29 FRONT DOOR SPEKER...30 Removal and Installation...30 RER DOOR SPEKER...31 Removal and Installation...31 UDIO NTENN...32 Location of udio ntenna System Component...32 Removal and Installation...32 PREMIUM UDIO (KING C) SIC INSPECTION...33 DIGNOSIS ND REPIR WORKFLOW...33 Work Flow...33 FUNCTION DIGNOSIS...35 UDIO SYSTEM...35 G H I J K L M V O P V-1
System Diagram... 35 System Description... 35 Component Parts Location... 36 Component Description... 37 HNDS-FREE PHONE SYSTEM... 38 System Diagram... 38 System Description... 38 Component Parts Location... 39 Component Description... 40 DIGNOSIS SYSTEM (UDIO UNIT)... 41 V SWITCH... 41 V SWITCH : Component Function Check... 41 DIGNOSIS SYSTEM (LUETOOTH CON- TROL UNIT)... 42 Diagnosis Description... 42 Work Flow... 42 COMPONENT DIGNOSIS... 43 POWER SUPPLY ND GROUND CIRCUIT... 43 UDIO UNIT... 43 UDIO UNIT : Diagnosis Procedure... 43 STELLITE RDIO TUNER... 43 STELLITE RDIO TUNER : Diagnosis Procedure... 43 LUETOOTH CONTROL UNIT... 44 LUETOOTH CONTROL UNIT : Diagnosis Procedure... 44 MICROPHONE... 45 MICROPHONE : Diagnosis Procedure... 45 FRONT DOOR SPEKER... 47 Description... 47 Diagnosis Procedure... 47 FRONT TWEETER... 49 Description... 49 Diagnosis Procedure... 49 RER DOOR SPEKER... 51 Description... 51 Diagnosis Procedure... 51 STEERING SWITCH... 53 Description... 53 Diagnosis Procedure... 53 COMMUNICTION SIGNL CIRCUIT... 55 STELLITE RDIO TUNER... 55 STELLITE RDIO TUNER : Description... 55 STELLITE RDIO TUNER : Diagnosis Procedure... 55 SOUND SIGNL CIRCUIT... 58 STELLITE RDIO TUNER... 58 STELLITE RDIO TUNER : Description... 58 STELLITE RDIO TUNER : Diagnosis Procedure... 58 MICROPHONE SIGNL CIRCUIT... 60 Description... 60 Diagnosis Procedure... 60 ECU DIGNOSIS... 62 UDIO UNIT... 62 Reference Value... 62 Wiring Diagram... 65 STELLITE RDIO TUNER... 76 Reference Value... 76 LUETOOTH CONTROL UNIT... 78 Reference Value... 78 SYMPTOM DIGNOSIS... 80 UDIO SYSTEM... 80 Symptom Table... 80 NORML OPERTING CONDITION... 81 Description... 81 PRECUTION... 82 PRECUTIONS... 82 Precaution for Supplemental Restraint System (SRS) "IR G" and "SET ELT PRE-TEN- SIONER"... 82 PREPRTION... 83 PREPRTION... 83 Commercial Service Tools... 83 ON-VEHICLE REPIR... 84 UDIO UNIT... 84 Removal and Installation... 84 FRONT TWEETER... 85 Removal and Installation... 85 FRONT DOOR SPEKER... 86 Removal and Installation... 86 RER DOOR SPEKER... 87 Removal and Installation... 87 STEERING SWITCH... 88 Removal and Installation... 88 LUETOOTH CONTROL UNIT... 89 Removal and Installation... 89 MICROPHONE... 91 Removal and Installation... 91 V-2
UDIO NTENN...92 Location of ntenna...92 Removal and Installation...92 STELLITE RDIO NTENN...94 Removal and Installation...94 STELLITE RDIO TUNER...95 Removal and Installation...95 PREMIUM UDIO (CREW C) SIC INSPECTION...96 DIGNOSIS ND REPIR WORKFLOW...96 Work Flow...96 FUNCTION DIGNOSIS...98 UDIO SYSTEM...98 System Diagram...98 System Description...98 Component Parts Location...99 Component Description... 100 HNDS-FREE PHONE SYSTEM... 101 System Diagram... 101 System Description... 101 Component Parts Location... 102 Component Description... 103 DIGNOSIS SYSTEM (UDIO UNIT)... 104 V SWITCH... 104 V SWITCH : Component Function Check... 104 DIGNOSIS SYSTEM (LUETOOTH CON- TROL UNIT)... 105 Diagnosis Description... 105 Work Flow... 105 COMPONENT DIGNOSIS... 106 POWER SUPPLY ND GROUND CIRCUIT... 106 UDIO UNIT... 106 UDIO UNIT : Diagnosis Procedure... 106 STELLITE RDIO TUNER... 106 STELLITE RDIO TUNER : Diagnosis Procedure... 106 UDIO MP... 107 UDIO MP : Diagnosis Procedure... 107 LUETOOTH CONTROL UNIT... 108 LUETOOTH CONTROL UNIT : Diagnosis Procedure... 108 MICROPHONE... 109 MICROPHONE : Diagnosis Procedure... 109 FRONT DOOR SPEKER... 111 Description... 111 Diagnosis Procedure...111 FRONT TWEETER... 114 Description...114 Diagnosis Procedure...114 RER DOOR SPEKER... 117 Description...117 Diagnosis Procedure...117 RER DOOR TWEETER... 120 Description...120 Diagnosis Procedure...120 SUWOOFER... 123 Description...123 Diagnosis Procedure...123 MP ON SIGNL CIRCUIT... 126 Description...126 Diagnosis Procedure...126 STEERING SWITCH... 127 Description...127 Diagnosis Procedure...127 COMMUNICTION SIGNL CIRCUIT... 129 STELLITE RDIO TUNER...129 STELLITE RDIO TUNER : Description...129 STELLITE RDIO TUNER : Diagnosis Procedure...129 SOUND SIGNL CIRCUIT... 132 STELLITE RDIO TUNER...132 STELLITE RDIO TUNER : Description...132 STELLITE RDIO TUNER : Diagnosis Procedure...132 MICROPHONE SIGNL CIRCUIT... 134 Description...134 Diagnosis Procedure...134 ECU DIGNOSIS... 136 UDIO UNIT... 136 Reference Value...136 Wiring Diagram...139 STELLITE RDIO TUNER... 153 Reference Value...153 UDIO MP... 155 Reference Value...155 LUETOOTH CONTROL UNIT... 158 Reference Value...158 SYMPTOM DIGNOSIS... 160 UDIO SYSTEM... 160 Symptom Table...160 C D E F G H I J K L M V O P V-3
NORML OPERTING CONDITION... 161 Description...161 PRECUTION...162 PRECUTIONS... 162 Precaution for Supplemental Restraint System (SRS) "IR G" and "SET ELT PRE-TEN- SIONER"...162 PREPRTION...163 PREPRTION... 163 Commercial Service Tools...163 ON-VEHICLE REPIR...164 UDIO UNIT... 164 Removal and Installation...164 UDIO MP... 165 Removal and Installation...165 FRONT TWEETER... 166 Removal and Installation...166 FRONT DOOR SPEKER... 167 Removal and Installation...167 RER DOOR SPEKER...168 Removal and Installation... 168 RER DOOR TWEETER...169 Removal and Installation... 169 STEERING SWITCH...170 Removal and Installation... 170 SUWOOFER...171 Removal and Installation... 171 LUETOOTH CONTROL UNIT...172 Removal and Installation... 172 MICROPHONE...174 Removal and Installation... 174 UDIO NTENN...175 Location of ntenna... 175 Removal and Installation... 175 STELLITE RDIO NTENN...177 Removal and Installation... 177 STELLITE RDIO TUNER...178 Removal and Installation... 178 V-4
< SIC INSPECTION > DIGNOSIS ND REPIR WORKFLOW SIC INSPECTION DIGNOSIS ND REPIR WORKFLOW Work Flow OVERLL SEQUENCE [SE UDIO] INFOID:0000000003301678 C D E F G H I J K L DETILED FLOW LNI0182G 1.GET INFORMTION FOR SYMPTOM Get detailed information from the customer about the symptom (the condition and the environment when the incident/malfunction occurred). >> GO TO 2 2.CONFIRM THE SYMPTOM Try to confirm the symptom described by the customer. Verify relation between the symptom and the condition when the symptom is detected. M V O P >> GO TO 3 3.DETECT MLFUNCTIONING PRT Y DIGNOSTIC PROCEDURE Inspect according to Diagnostic Procedure of the system. V-5
< SIC INSPECTION > DIGNOSIS ND REPIR WORKFLOW Is malfunctioning part detected? YES >> GO TO 4 NO >> GO TO 2 4.REPIR OR REPLCE THE MLFUNCTIONING PRT 1. Repair or replace the malfunctioning part. 2. Reconnect parts or connectors disconnected during Diagnostic Procedure. [SE UDIO] >> GO TO 5 5.FINL CHECK Refer to confirmed symptom in step 2, and make sure that the symptom is not detected. Has the symptom been repaired? YES >> Inspection End. NO >> GO TO 2 V-6
UDIO SYSTEM < FUNCTION DIGNOSIS > [SE UDIO] FUNCTION DIGNOSIS UDIO SYSTEM System Diagram INFOID:0000000003301679 C D E F System Description WNI0788G INFOID:0000000003301680 G UDIO SYSTEM The audio system consists of the following components udio unit Rod antenna Front door speakers Front tweeters Rear door speakers When the audio system is on, radio signals are received by the rod antenna. The audio unit then sends audio signals to the front door speakers, front tweeters and rear door speakers. Refer to Owner's Manual for audio system operating instructions. H I J K L M V O P V-7
UDIO SYSTEM < FUNCTION DIGNOSIS > [SE UDIO] Component Parts Location INFOID:0000000003301681 WNI0843G 1. Front tweeter LH M109 RH M111 4. Rear door speaker (crew cab) LH D207 RH D307 Component Description 2. udio unit M43 3. Front door speaker LH D12 RH D112 5. Rear door speaker (king cab) LH 76 RH 160 INFOID:0000000003301682 udio unit Front door speakers Front tweeters Rear door speakers Part name Description Controls audio system functions Outputs audio signal from audio unit Outputs high, mid and low range sounds Outputs audio signal from audio unit Outputs high range sounds Outputs audio signal from audio unit Outputs high, mid and low range sounds V-8
POWER SUPPLY ND GROUND CIRCUIT < COMPONENT DIGNOSIS > [SE UDIO] COMPONENT DIGNOSIS POWER SUPPLY ND GROUND CIRCUIT UDIO UNIT UDIO UNIT : Diagnosis Procedure 1.CHECK FUSES Check that the following fuses of the audio unit are not are not blown. udio unit Unit Terminals Signal name Fuse No. 19 attery power 29 7 CC or ON 4 re the fuses OK? YES >> GO TO 2 NO >> If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse. 2.POWER SUPPLY CIRCUIT CHECK 1. Disconnect audio unit connector M43. 2. Check voltage between the audio unit connector M43 ground. INFOID:0000000003301683 C D E F G Connector M43 (+) Terminal (-) OFF CC ON 7 Ground 0V 19 Ground attery voltage attery voltage attery voltage attery voltage attery voltage re the voltage results as specified? YES >> GO TO 3 NO >> Check connector housings for disconnected or loose terminals. Repair harness or connector. 3.GROUND CIRCUIT CHECK Inspect audio unit case ground. Does case ground pass inspection? YES >> Inspection end. NO >> Repair audio unit case ground. LNI0674G H I J K L M V O P V-9
FRONT DOOR SPEKER < COMPONENT DIGNOSIS > [SE UDIO] FRONT DOOR SPEKER Description The audio unit sends audio signals to the front door speakers using the front door speaker circuits. Diagnosis Procedure 1.HRNESS CHECK 1. Disconnect audio unit connector M43 and suspect speaker connector. 2. Check continuity between audio unit harness connector M43 () terminal and suspect speaker harness connector () terminal. INFOID:0000000003301684 INFOID:0000000003301685 Connector Terminal Connector Terminal M43 2 1 D12 3 2 11 1 D112 12 2 3. Check continuity between audio unit harness connector M43 () terminal and ground. Continuity Yes Connector M43 Terminal 2 3 11 12 Continuity Ground re continuity results as specified? YES >> GO TO 2 NO >> Check connector housings for disconnected or loose terminals. Repair harness or connector. 2.FRONT SPEKER SIGNL CHECK No WNI0031ZZ V-10
FRONT DOOR SPEKER < COMPONENT DIGNOSIS > [SE UDIO] 1. Connect audio unit connector M43 and front speaker connector. 2. Turn ignition to CC. 3. Push POWER. 4. Check the signal between audio unit harness connector M43 terminals with CONSULT-III or oscilloscope. (+) (-) Connector Terminal Terminal Condition Reference signal C 2 3 D M43 11 12 Receive audio signal E SKI0177E Is the audio signal voltage as specified? YES >> Replace speaker. Refer to V-30, "Removal and Installation". NO >> Replace audio unit. Refer to V-28, "Removal and Installation". WNI0032ZZ F G H I J K L M V O P V-11
FRONT TWEETER < COMPONENT DIGNOSIS > [SE UDIO] FRONT TWEETER Description INFOID:0000000003301686 The audio unit sends audio signals to the front tweeters using the front tweeter circuits. Diagnosis Procedure INFOID:0000000003301687 1.HRNESS CHECK 1. Disconnect audio unit connector M43 and suspect front tweeter connector. 2. Check continuity between audio unit harness connector M43 () and suspect front tweeter harness connector (). Connector Terminal Connector Terminal M43 2 1 M109 3 2 11 1 M111 12 2 3. Check continuity between audio unit harness connector M43 () and ground. Continuity Yes Connector M43 Terminal 2 3 11 12 Continuity Ground re the continuity results as specified? YES >> GO TO 2 NO >> Check connector housings for disconnected or loose terminals. Repair harness or connector. 2.FRONT TWEETER SIGNL CHECK No WNI0031ZZ V-12
FRONT TWEETER < COMPONENT DIGNOSIS > [SE UDIO] 1. Connect audio unit connector M43 and front tweeter connector. 2. Turn ignition to CC. 3. Push POWER. 4. Check the signal between audio unit harness connector M43 terminals with CONSULT-III or oscilloscope. (+) (-) Connector Terminal Terminal Condition Reference signal C 2 3 D M43 11 12 Receive audio signal E SKI0177E Is the audio signal voltage as specified? YES >> Replace the suspect front tweeter. Refer to V-29, "Removal and Installation". NO >> Replace audio unit. Refer to V-28, "Removal and Installation". WNI0032ZZ F G H I J K L M V O P V-13
RER DOOR SPEKER < COMPONENT DIGNOSIS > [SE UDIO] RER DOOR SPEKER Description The audio unit sends audio signals to the rear door speakers using the rear door speaker circuits. Diagnosis Procedure 1.HRNESS CHECK 1. Disconnect audio unit connector M43 and suspect rear door speaker connector. 2. Check continuity between audio unit harness connector M43 () and suspect rear door speaker harness connector (). INFOID:0000000003301688 INFOID:0000000003301689 Connector Terminal Connector Terminal M43 4 1 D207 5 2 13 1 D307 14 2 3. Check continuity between audio unit harness connector M43 () and ground. Continuity Yes Connector M43 Terminal 4 5 13 14 Continuity Ground re the continuity results as specified? YES >> GO TO 2 NO >> Check connector housings for disconnected or loose terminals. Repair harness or connector. 2.RER DOOR SPEKER SIGNL CHECK No WNI0033ZZ V-14
RER DOOR SPEKER < COMPONENT DIGNOSIS > [SE UDIO] 1. Connect audio unit connector and rear door speaker connector. 2. Turn ignition to CC. 3. Push POWER. 4. Check the signal between audio unit harness connector M43 terminals with CONSULT-III or oscilloscope. Connector (+) (-) Terminal Terminal 4 5 Condition Reference signal C M43 13 14 Receive audio signal D E SKI0177E Is the audio signal voltage as specified? YES >> Replace the suspect rear door speaker. Refer to V-31, "Removal and Installation". NO >> Replace audio unit. Refer to V-28, "Removal and Installation". WNI0034ZZ F G H I J K L M V O P V-15
< ECU DIGNOSIS > ECU DIGNOSIS UDIO UNIT Reference Value TERMINL LYOUT UDIO UNIT [SE UDIO] INFOID:0000000003301690 LNI0675G PHYSICL VLUES Terminal (Wire color) Description + Signal name Input/ Output Condition Reference value (pprox.) 2 (R) 3 (L) Sound signal front door speaker and front tweeter LH Output ON udio output SKI3609E 4 (G) 5 () Sound signal rear door speaker LH Output ON udio output SKI3609E 7 (G/) Ground CC power supply Input CC or ON attery voltage 8 (GR) Ground ILL control Input CC or ON 0V 9 (R) Ground Light Input CC or ON attery voltage V-16
< ECU DIGNOSIS > UDIO UNIT [SE UDIO] Terminal (Wire color) Description + Signal name Input/ Output Condition Reference value (pprox.) 11 (LG) 12 (R) Sound signal front door speaker and front tweeter RH Output ON Voice output C SKI3609E D 13 (GR) 14 (O) Sound signal rear door speaker RH Output ON Voice output E F SKI3609E 19 (Y) Ground attery power supply Input OFF attery voltage G H I J K L M V O P V-17
< ECU DIGNOSIS > Wiring Diagram UDIO UNIT [SE UDIO] INFOID:0000000003301691 WNW0140G V-18
< ECU DIGNOSIS > UDIO UNIT [SE UDIO] C D E F G H I J K L M V O WNI0674G P V-19
< ECU DIGNOSIS > UDIO UNIT [SE UDIO] WNI0675G V-20
< ECU DIGNOSIS > UDIO UNIT [SE UDIO] C D E F G H I J K L M V O WNI0676G P V-21
< ECU DIGNOSIS > UDIO UNIT [SE UDIO] WNI0677G V-22
< ECU DIGNOSIS > UDIO UNIT [SE UDIO] C D E F G H I J K L M V O WNI0678G P V-23
UDIO SYSTEM < SYMPTOM DIGNOSIS > [SE UDIO] SYMPTOM DIGNOSIS UDIO SYSTEM Symptom Table UDIO SYSTEM Inoperative ll speakers do not sound One or several speakers do not sound CD INFOID:0000000003301692 Symptom Possible cause Reference page udio unit power circuit udio unit udio unit udio unit power circuit Front door speaker Front tweeter Rear door speaker V-9 V-9 V-10 V-12 V-14 Symptom Possible cause Reference page CD cannot be inserted. CD cannot be ejected. The CD cannot be played. The sound skips, stops suddenly, or is distorted. udio unit V-9 V-24
NORML OPERTING CONDITION < SYMPTOM DIGNOSIS > [SE UDIO] NORML OPERTING CONDITION Description INFOID:0000000003301693 The majority of the audio concerns are the result of outside causes (bad CD, electromagnetic interference, etc.). NOISE The following noise results from variations in field strength, such as fading noise and multi-path noise, or external noise from trains and other sources. It is not a malfunction. Fading noise: This noise occurs because of variations in the field strength in a narrow range due to mountains or buildings blocking the signal. Multi-path noise: This noise results from the waves sent directly from the broadcast station arriving at the antenna at a different time from the waves which reflect off mountains or buildings. The vehicle itself can be a source of noise if noise prevention parts or electrical equipment is malfunctioning. Check if noise is caused and/or changed by engine speed, ignition turned to each position, and operation of each piece of electrical equipment, and determine the cause. NOTE: The source of the noise can be found easily by listening to the noise while removing the fuses of electrical components, one by one. Type of Noise and Possible Cause Occurrence condition continuous growling noise occurs. The speed of Occurs only when engine is ON. the noise varies with changes in the engine speed. The occurrence of the noise is linked with the operation of the fuel pump. Noise only occurs when various electrical components are operating. cracking or snapping sound occurs with the operation of various es. The noise occurs when various motors are operating. The noise occurs constantly, not just under certain conditions. cracking or snapping sound occurs while the vehicle is being driven, especially when it is vibrating excessively. components Possible cause Fuel pump condenser Relay malfunction, audio unit malfunction Motor case ground Motor Rear defogger coil malfunction Open circuit in printed heater Poor ground of antenna feeder line Ground wire of body parts Ground due to improper part installation Wiring connections or a short circuit C D E F G H I J K L M V O P V-25
< PRECUTION > PRECUTION PRECUTIONS PRECUTIONS [SE UDIO] Precaution for Supplemental Restraint System (SRS) "IR G" and "SET ELT PRE-TENSIONER" INFOID:0000000003221781 The Supplemental Restraint System such as IR G and SET ELT PRE-TENSIONER, used along with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain types of collision. This system includes seat belt inputs and dual stage front air bag modules. The SRS system uses the seat belt es to determine the front air bag deployment, and may only deploy one front air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted. Information necessary to service the system safely is included in the SR and S section of this Service Manual. WRNING: To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in the event of a collision which would result in air bag inflation, all maintenance must be performed by an authorized NISSN/INFINITI dealer. Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system. For removal of Spiral Cable and ir ag Module, see the SR section. Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness connectors. V-26
< PREPRTION > PREPRTION PREPRTION PREPRTION [SE UDIO] Commercial Service Tools INFOID:0000000003221782 Tool name Description Loosening bolts and nuts C Power tool D PIC0191E E F G H I J K L M V O P V-27
UDIO UNIT < ON-VEHICLE REPIR > [SE UDIO] ON-VEHICLE REPIR UDIO UNIT Removal and Installation INFOID:0000000003301744 REMOVL 1. Remove the cluster lid C. Refer to IP-10, "Removal and Installation". 2. Remove the audio control unit screws, using power tool. 3. Pull out the audio control unit from the instrument panel and disconnect the audio control unit connectors. INSTLLTION Installation is in the reverse order of removal. LKI0582E V-28
FRONT TWEETER < ON-VEHICLE REPIR > [SE UDIO] FRONT TWEETER Removal and Installation INFOID:0000000003301745 REMOVL CUTION: Use a suitable tool to prevent damage to the front tweeter speaker grille trim and the instrument panel. 1. Remove the front tweeter grille. 2. Remove the front tweeter screws (). 3. Pull out the front tweeter speaker (1) and disconnect front tweeter connector, then remove the front tweeter speaker (1). C D E INSTLLTION Installation is in the reverse order of removal. LNI1074ZZ F G H I J K L M V O P V-29
FRONT DOOR SPEKER < ON-VEHICLE REPIR > [SE UDIO] FRONT DOOR SPEKER Removal and Installation INFOID:0000000003301746 REMOVL 1. Remove the front door finisher. Refer to INT-13, "Removal and Installation". 2. Remove the front door speaker screws (). 3. Pull out the front door speaker (1), and disconnect the front door speaker connector and remove the front door speaker (1). INSTLLTION Installation is in the reverse order of removal. LNI0347ZZ V-30
RER DOOR SPEKER < ON-VEHICLE REPIR > [SE UDIO] RER DOOR SPEKER Removal and Installation REMOVL 1. Remove the rear door finisher. Refer to INT-13, "Removal and Installation". 2. Remove the rear door speaker screws (). 3. Remove rear door speaker (1), disconnect rear door speaker connector (). NOTE: King cab shown, crew cab similar. INFOID:0000000003302258 C D E INSTLLTION Installation is in the reverse order of removal. LNI1071ZZ F G H I J K L M V O P V-31
UDIO NTENN < ON-VEHICLE REPIR > [SE UDIO] UDIO NTENN Location of udio ntenna System Component INFOID:0000000003301748 WNI0844G 1. udio antenna 2. ntenna feeder 3. udio unit M43 Removal and Installation INFOID:0000000003301749 REMOVL 1. Remove lower glove box. Refer to IP-10, "Removal and Installation". 2. Disconnect audio antenna cable from antenna feeder. 3. Remove antenna rod. 4. Remove rubber seal. 5. Remove cowl top. Refer to EXT-19, "Removal and Installation". 6. Remove fender protector. Refer to EXT-22, "Removal and Installation of Front Fender Protector". 7. Remove antenna base bolts. 8. Remove antenna base and cable. INSTLLTION Installation is in the reverse order of removal. CUTION: lways properly tighten the antenna rod during installation or the antenna rod may bend or break during vehicle operation. EL610C V-32
DIGNOSIS ND REPIR WORKFLOW < SIC INSPECTION > [PREMIUM UDIO (KING C)] SIC INSPECTION DIGNOSIS ND REPIR WORKFLOW Work Flow OVERLL SEQUENCE INFOID:0000000003301764 C D E F G H I J K L DETILED FLOW LNI0182G 1.GET INFORMTION FOR SYMPTOM Get detailed information from the customer about the symptom (the condition and the environment when the incident/malfunction occurred). >> GO TO 2 2.CONFIRM THE SYMPTOM Try to confirm the symptom described by the customer. Verify relation between the symptom and the condition when the symptom is detected. M V O P >> GO TO 3 3.DETECT MLFUNCTIONING PRT Y DIGNOSTIC PROCEDURE Inspect according to Diagnostic Procedure of the system. V-33
DIGNOSIS ND REPIR WORKFLOW < SIC INSPECTION > [PREMIUM UDIO (KING C)] Is malfunctioning part detected? YES >> GO TO 4 NO >> GO TO 2 4.REPIR OR REPLCE THE MLFUNCTIONING PRT 1. Repair or replace the malfunctioning part. 2. Reconnect parts or connectors disconnected during Diagnostic Procedure. >> GO TO 5 5.FINL CHECK Refer to confirmed symptom in step 2, and make sure that the symptom is not detected. Was the repair confirmed? YES >> Inspection End. NO >> GO TO 2 V-34
UDIO SYSTEM < FUNCTION DIGNOSIS > [PREMIUM UDIO (KING C)] FUNCTION DIGNOSIS UDIO SYSTEM System Diagram INFOID:0000000003301765 C D E F G H I J System Description WNI0845G INFOID:0000000003301766 K UDIO SYSTEM The audio system consists of the following components udio unit udio amp. Rod antenna Steering wheel audio control es Front door speakers Front tweeters Rear door speakers When the audio system is on, radio signals are received by the rod antenna. The audio unit then sends audio signals to the audio amp. The audio amp. amplifies the audio signals before sending them to the front door speakers, front tweeters and rear door speakers. Refer to Owner's Manual for audio system operating instructions. STELLITE RDIO SYSTEM The satellite radio system consists of the following components Satellite antenna Satellite radio tuner When the satellite radio system is on, radio signals are supplied to the satellite radio tuner from the satellite antenna. The satellite radio tuner then sends audio signals to the audio unit. Refer to Owner's Manual for satellite radio system operating instructions. SPEED SENSITIVE VOLUME SYSTEM L M V O P V-35
UDIO SYSTEM < FUNCTION DIGNOSIS > [PREMIUM UDIO (KING C)] Volume level of this system goes up and down automatically in proportion to the vehicle speed. The control level can be selected by the customer. Refer to Owner's Manual for operating instructions. Component Parts Location INFOID:0000000003301767 :FRONT 1. Front tweeter LH M109 2. Combination meter M24 3. udio unit M42, M43, M44, M45 4. Front tweeter RH M111 5. ux jack M85 6. Satellite radio tuner M41, M129 V-36 WNI0846ZZ
UDIO SYSTEM < FUNCTION DIGNOSIS > [PREMIUM UDIO (KING C)] 7. Steering wheel audio control es 10. luetooth control unit 141 (view with passenger front seat removed) Component Description 8. Front door speaker LH D12 RH D112 9. Rear door speaker LH D207 RH D307 11. Microphone R8 12. luetooth ON indicator R6 INFOID:0000000003301768 Part name udio unit udio amp. Steering wheel audio control es Front door speakers Front tweeters Rear door speakers Satellite radio tuner Satellite antenna Description Controls audio system and satellite radio system functions Receives power (amp ON) and audio signals from udio unit and outputs audio signals to each speaker. Start a voice recognition session nswer and end telephone calls djust the volume level Outputs audio signal from audio amp. Outputs high, mid and low range sounds Outputs audio signal from audio amp. Outputs high range sounds Outputs audio signal from audio amp. Outputs high, mid and low range sounds Receives radio signals from satellite antenna Sends audio signals to udio unit udio signal (satellite radio) is received and output to udio unit. C D E F G H I J K L M V O P V-37
HNDS-FREE PHONE SYSTEM < FUNCTION DIGNOSIS > [PREMIUM UDIO (KING C)] HNDS-FREE PHONE SYSTEM System Diagram INFOID:0000000003301769 WNI0848G System Description INFOID:0000000003301770 Refer to the Owner's Manual for luetooth telephone system operating instructions. NOTE: Cellular telephones must have their wireless connection set up (paired) before using the luetooth telephone system. luetooth telephone system allows users who have a luetooth equipped cellular telephone to make a wireless connection between their cellular telephone and the luetooth control unit. Hands-free cellular telephone calls can be sent and received. Some luetooth cellular telephones may not be recognized by the luetooth control unit. When a cellular telephone or the luetooth control unit is replaced, the telephone must be paired with the luetooth control unit. Different cellular telephones may have different pairing procedures. Refer to the cellular telephone operating manual. LUETOOTH CONTROL UNIT When the ignition is turned to CC or ON, the luetooth control unit will power up. During power up, the luetooth control unit is initialized and performs various self checks. Initialization may take up to 10 seconds. During this time, the luetooth ON indicator will flash until initialization is complete. If a phone is present in the vehicle and paired with the luetooth control unit, Nissan Voice Recognition will then become active. luetooth telephone functions can be turned off using the Nissan Voice Recognition system. STEERING WHEEL UDIO CONTROL SWITCHES When buttons on the steering wheel audio control are pushed, the resistance in steering wheel audio control circuit changes depending on which button is pushed. The luetooth control unit uses this signal to perform various functions while navigating through the voice recognition system. The following functions can be performed using the steering wheel audio control : Initiate Self Diagnosis of the luetooth telephone system Start a voice recognition session nswer and end telephone calls djust the volume of calls MICROPHONE The microphone is located in the roof console assembly. The microphone sends a signal to the luetooth control unit. The microphone can be actively tested during self-diagnosis. UDIO UNIT The audio unit receives signals from the luetooth control unit and sends audio signals to the speakers. LUETOOTH ON INDICTOR The luetooth ON indicator is located in the overhead console. The indicator will flash during power up whilethe luetooth control unit is initializing. This process may take up to 10 seconds. If a phone is present in thevehicle and paired with the luetooth control unit, the indicator will remain on to indicate that the system isready for voice commands. The indicator flashes during self-diagnosis. V-38
HNDS-FREE PHONE SYSTEM < FUNCTION DIGNOSIS > [PREMIUM UDIO (KING C)] Component Parts Location INFOID:0000000003302293 C D E F G H I J K L M V O P WNI0846ZZ :FRONT 1. Front tweeter LH M109 2. Combination meter M24 3. udio unit M42, M43, M44, M45 4. Front tweeter RH M111 5. ux jack M85 6. Satellite radio tuner M41, M129 V-39
HNDS-FREE PHONE SYSTEM < FUNCTION DIGNOSIS > [PREMIUM UDIO (KING C)] 7. Steering wheel audio control es 10. luetooth control unit 141 (view with passenger front seat removed) Component Description 8. Front door speaker LH D12 RH D112 9. Rear door speaker LH D207 RH D307 11. Microphone R8 12. luetooth ON indicator R6 INFOID:0000000003301772 Part name udio unit Front door speaker Front tweeter Steering wheel audio control es Microphone luetooth control unit luetooth antenna luetooth ON indicator Description Receives telephone voice signal from luetooth control unit Sends telephone voice and voice guidance signals to the speakers Receives telephone voice and voice guidance signals from the audio amp. Start a voice recognition session nswer and end telephone calls djust the volume level Sends voice signals to luetooth control unit Controls hands-free phone functions Sends telephone voice signal to luetooth control unit Controlled by the luetooth control unit V-40
DIGNOSIS SYSTEM (UDIO UNIT) < FUNCTION DIGNOSIS > [PREMIUM UDIO (KING C)] DIGNOSIS SYSTEM (UDIO UNIT) V SWITCH V SWITCH : Component Function Check INFOID:0000000003301773 STRTING THE SELF-DIGNOSIS MODE 1. Turn ignition from OFF to CC. 2. Press and hold the DISP/CLOCK and turn the volume control dial clockwise or counterclockwise for 30 clicks or more. C D E F G Then the self-diagnosis operates. single beep indicates self-diagnosis mode is active. 3. Initially, all display segments will be illuminated. 4. Press each. When each is pressed, its name and communication code will be displayed NOTE: CD player LOD and EJECT buttons are not included in this test and will not change the display when pressed. DIGNOSIS FUNCTION It can check for continuity of the es by sounding the beep when each audio unit and steering is pressed. It can check for continuity of harness between audio unit and steering. EXITING THE SELF-DIGNOSIS MODE Turn ignition OFF. Then the self-diagnosis ends. WKI5819E H I J K L M V O P V-41
DIGNOSIS SYSTEM (LUETOOTH CONTROL UNIT) < FUNCTION DIGNOSIS > [PREMIUM UDIO (KING C)] DIGNOSIS SYSTEM (LUETOOTH CONTROL UNIT) Diagnosis Description INFOID:0000000003301774 The luetooth control unit has two diagnostic checks. The first diagnostic check is performed automatically every ignition cycle during control unit initialization. The second diagnostic check is performed by the technician using the steering wheel audio control es prior to trouble diagnosis. LUETOOTH CONTROL UNIT INITILIZTION CHECKS Internal control unit failure luetooth antenna connection open or shorted Steering wheel audio control es [SEND( )/END( )] stuck closed Vehicle speed pulse count Microphone connection test (with playback to operator) luetooth inquiry check OPERTION PROCEDURE 1. Turn ignition to CC or ON. 2. Wait for the luetooth system to complete initialization. This may take up to 10 seconds. 3. Press and hold the steering wheel audio control button for at least 5 seconds. The luetooth system will begin to play a verbal prompt. LNI0448G 4. While the prompt is playing, press and hold the steering wheel audio control button until you hear the Diagnostics mode prompt. The luetooth system will sound a 5 second beep. 5. While the beep is sounding, press and hold the steering wheel audio control button again until you hear prompts. 6. The luetooth system has now entered into the diagnostic mode. Results of the diagnostic checks will be verbalized to the technician and the luetooth ON indicator will flash. Refer to V- 42, "Work Flow". 7. fter the failure records are reported, an interactive microphone test will be performed. Follow the voice prompt. If the microphone test fails refer to V-42, "Work Flow". 8. Self-diagnosis mode is complete when the voice prompt says ll diagnostic functions completed. Work Flow LNI0449G INFOID:0000000003301775 Failure Message Internal failure ction Replace luetooth control unit. Refer to V-89, "Removal and Installation". luetooth antenna open 1. Inspect harness connection. luetooth antenna shorted Phone/Send for Hands Free System is stuck 2. Replace luetooth antenna. Refer to V-89, "Removal and Installation". Check steering wheel audio control es. Refer to V-53, "Description". Phone/End for the Hands Free System is stuck Microphone test (failed interactive test) 1. Inspect harness between luetooth control unit and microphone. 2. Replace microphone. Refer to V-91, "Removal and Installation". V-42
POWER SUPPLY ND GROUND CIRCUIT < COMPONENT DIGNOSIS > [PREMIUM UDIO (KING C)] COMPONENT DIGNOSIS POWER SUPPLY ND GROUND CIRCUIT UDIO UNIT UDIO UNIT : Diagnosis Procedure 1.CHECK FUSES Check that the following fuses of the audio unit are not are not blown. udio unit Unit Terminals Signal name Fuse No. 6 attery power 29 10 CC or ON 4 re the fuses OK? YES >> GO TO 2 NO >> If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse. 2.POWER SUPPLY CIRCUIT CHECK 1. Disconnect audio unit connector M43. 2. Check voltage between the audio unit connector M43 and ground. INFOID:0000000003301776 C D E F G Connector M43 (+) Terminal re the voltage results as specified? YES >> GO TO 3 NO >> Check connector housing for disconnected or loose terminals. Repair harness or connector. 3.GROUND CIRCUIT CHECK Inspect audio unit case ground. Does case ground pass inspection? YES >> Inspection End. NO >> Repair audio unit case ground. STELLITE RDIO TUNER (-) OFF CC ON 6 Ground 0V 10 Ground attery voltage attery voltage attery voltage attery voltage attery voltage STELLITE RDIO TUNER : Diagnosis Procedure 1.CHECK FUSES Check that the following fuses of the satellite radio tuner (factory installed) are not blown. LNI0695G INFOID:0000000003301777 H I J K L M V O Unit Terminals Signal name Fuse No. Satellite radio tuner (factory installed) 32 attery power 17 36 CC or ON 4 re the fuses OK? YES >> GO TO 2 NO >> If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse. 2.POWER SUPPLY CIRCUIT CHECK P V-43
POWER SUPPLY ND GROUND CIRCUIT < COMPONENT DIGNOSIS > [PREMIUM UDIO (KING C)] 1. Turn ignition OFF. 2. Disconnect satellite radio tuner (factory installed) connector M41. 3. Check voltage between the satellite radio tuner (factory installed) and ground. Connector M41 (+) Terminal re the voltage readings as specified? YES >> GO TO 3 NO >> Check connector housings for disconnected or loose terminals. Repair harness or connector. 3.GROUND CIRCUIT CHECK Inspect satellite radio tuner (factory installed) case ground. Does case ground pass inspection? YES >> Inspection End. NO >> Repair satellite radio tuner (factory installed) case ground. LUETOOTH CONTROL UNIT (-) OFF CC ON attery 32 voltage Ground 36 0V attery voltage attery voltage attery voltage attery voltage LUETOOTH CONTROL UNIT : Diagnosis Procedure WKI4539E INFOID:0000000003301779 1.CHECK FUSE Check that the following fuses for the luetooth control unit are not blown. luetooth control unit Unit Terminal Signal name Fuse No. 1 attery power 29 2 CC or ON 4 3 ON or STRT 12 Is inspection result OK? YES >> GO TO 2. NO >> e sure to eliminate cause of malfunction before installing new fuse. 2.CHECK POWER SUPPLY CIRCUIT Check voltage between luetooth control unit harness connector 141 and ground. Connector 141 (+) Terminal 1 (-) OFF ON CC attery voltage 2 Ground 0V 3 0V attery voltage attery voltage attery voltage attery voltage attery voltage Is battery voltage present as specified? YES >> GO TO 3. NO >> Check harness between luetooth control unit and fuse. 3.CHECK GROUND CIRCUIT 0V LNI0323G V-44
POWER SUPPLY ND GROUND CIRCUIT < COMPONENT DIGNOSIS > [PREMIUM UDIO (KING C)] 1. Turn ignition OFF. 2. Disconnect luetooth control unit connector. 3. Check continuity between luetooth control unit harness connector 141 and ground. Connector Terminal Continuity 141 re continuity results as specified? YES >> Inspection End. NO >> Repair harness or connector. MICROPHONE 4 20 22 Ground MICROPHONE : Diagnosis Procedure 1.CHECK POWER SUPPLY CIRCUIT (MICROPHONE SIDE) 1. Turn ignition ON. 2. Check voltage between microphone harness connector R8 terminal 4 and ground. Yes WNI0853ZZ INFOID:0000000003301780 C D E F G (+) (-) Value (pprox.) Connector Terminal R8 4 Ground 5V Is approximately 5V present? YES >> GO TO 3 NO >> GO TO 2 2.CHECK POWER SUPPLY CIRCUIT (CONTINUITY) 1. Turn ignition OFF. 2. Disconnect microphone and luetooth control unit harness connectors. 3. Check continuity between microphone harness connector R8 () terminal 4 and luetooth control unit harness connector 141 () terminal 29. WKI5796E H I J K L Continuity Connector Terminal Connector Terminal R8 4 141 29 Yes 4. Check continuity between microphone harness connector R8 () terminal 4 and ground. LNI0320G M V Connector Terminal Continuity R8 4 Ground No re the continuity test results as specified? YES >> Replace the luetooth control unit. Refer to V-89, "Removal and Installation". NO >> Repair harness or connector. 3.CHECK GROUND CIRCUIT O P V-45
POWER SUPPLY ND GROUND CIRCUIT < COMPONENT DIGNOSIS > [PREMIUM UDIO (KING C)] 1. Turn ignition OFF. 2. Disconnect microphone harness connector R8 and luetooth control unit harness connector 141. 3. Check continuity between microphone harness connector R8 () terminal 2 and luetooth control unit harness connector 141 () terminal 8. Connector Terminal Connector Terminal Continuity R8 2 141 8 Yes Does continuity exist? YES >> Inspection End. NO >> Repair harness or connector. LNI0322G V-46
FRONT DOOR SPEKER < COMPONENT DIGNOSIS > [PREMIUM UDIO (KING C)] FRONT DOOR SPEKER Description INFOID:0000000003301781 The audio unit sends audio signals to the front door speakers using the audio signal circuits. Diagnosis Procedure 1.SPEKER HRNESS CHECK 1. Disconnect audio unit connector M43 and suspect speaker connector. 2. Check continuity between audio unit harness connector M43 () and suspect speaker harness connector (). Connector Terminal Connector Terminal M43 3. Check continuity between audio unit harness connector M43 () and ground. Connector M43 1 2 D12 2 1 3 2 D112 4 1 Terminal 1 2 3 4 re continuity test results as specified? YES >> GO TO 2 NO >> Check connector housings for disconnected or loose terminals. Repair harness or connector. 2.SPEKER SIGNL CHECK Continuity Yes Continuity Ground No INFOID:0000000003301782 WNI0849ZZ C D E F G H I J K L M V O P V-47
FRONT DOOR SPEKER < COMPONENT DIGNOSIS > [PREMIUM UDIO (KING C)] 1. Connect audio unit connector and audio amp. connector. 2. Turn ignition CC. 3. Push POWER. 4. Check the signal between audio unit harness connector M43 terminals with CONSULT-III or oscilloscope. Connector Terminals (+) (-) Condition Reference signal 1 2 M43 3 4 Receive audio signal SKI0177E re the audio signal voltage readings as specified? YES >> Replace suspect speaker. Refer to V-86, "Removal and Installation". NO >> Replace audio unit. Refer to V-84, "Removal and Installation". LNI0721G V-48
FRONT TWEETER < COMPONENT DIGNOSIS > [PREMIUM UDIO (KING C)] FRONT TWEETER Description INFOID:0000000003301783 The audio unit sends audio signals to the tweeters using the audio signal circuits. Diagnosis Procedure 1.SPEKER HRNESS CHECK 1. Disconnect audio unit connector M43 and suspect speaker connector. 2. Check continuity between audio unit harness connector M43 () and suspect speaker harness connector (). Connector Terminal Connector Terminal M43 3. Check continuity between audio unit harness connector M43 () and ground. Connector M43 1 2 M109 2 1 3 2 M111 4 1 Terminal 1 2 3 4 re continuity test results as specified? YES >> GO TO 2 NO >> Check connector housings for disconnected or loose terminals. Repair harness or connector. 2.SPEKER SIGNL CHECK Continuity Yes Continuity Ground No INFOID:0000000003301784 WNI0849ZZ C D E F G H I J K L M V O P V-49
FRONT TWEETER < COMPONENT DIGNOSIS > [PREMIUM UDIO (KING C)] 1. Connect audio unit connector and audio amp. connector. 2. Turn ignition CC. 3. Push POWER. 4. Check the signal between audio unit harness connector M43 terminals with CONSULT-III or oscilloscope. Connector Terminals (+) (-) Condition Reference signal 1 2 M43 3 4 Receive audio signal SKI0177E re the audio signal voltage readings as specified? YES >> Replace suspect speaker. Refer to V-85, "Removal and Installation". NO >> Replace audio unit. Refer to V-84, "Removal and Installation". LNI0721G V-50
RER DOOR SPEKER < COMPONENT DIGNOSIS > [PREMIUM UDIO (KING C)] RER DOOR SPEKER Description INFOID:0000000003301785 The audio unit sends audio signals to the rear door speakers using the audio signal circuits. Diagnosis Procedure 1.SPEKER HRNESS CHECK 1. Disconnect audio unit connector M44 and the suspect speaker connector. 2. Check continuity between audio unit harness connector M44 () and suspect speaker harness connector (). Connector Terminal Connector Terminal M44 3. Check continuity between audio unit harness connector M44 () and ground. Connector M44 13 2 76 14 1 15 2 160 16 1 Terminal 13 14 15 16 re the continuity test results as specified? YES >> GO TO 2 NO >> Check connector housings for disconnected or loose terminals. Repair harness or connector. 2.SPEKER SIGNL CHECK Continuity Yes Continuity Ground No INFOID:0000000003301786 WNI0851ZZ C D E F G H I J K L M V O P V-51
RER DOOR SPEKER < COMPONENT DIGNOSIS > [PREMIUM UDIO (KING C)] 1. Connect audio unit connector M44 and audio amp. connector 159. 2. Turn ignition to CC. 3. Push POWER. 4. Check the signal between audio unit harness connector M44 terminals with CONSULT-III or oscilloscope. Connector Terminals (+) (-) Condition Reference signal 13 14 M44 15 16 Receive audio signal SKI0177E Is the audio signal voltage reading as specified? YES >> Replace suspect speaker. Refer to V-87, "Removal and Installation". NO >> Replace audio unit. Refer to V-84, "Removal and Installation". LNI0730G V-52
STEERING SWITCH < COMPONENT DIGNOSIS > [PREMIUM UDIO (KING C)] STEERING SWITCH Description INFOID:0000000003301793 When one of the steering wheel audio control es is pushed, the resistance in the steering wheel audio control circuit changes depending on which button is pushed. Diagnosis Procedure INFOID:0000000003301794 C 1.CHECK STEERING WHEEL UDIO CONTROL SWITCH RESISTNCE 1. Turn ignition OFF. 2. Disconnect steering wheel audio control connector M102. 3. Check resistance between steering connector terminals. D E Terminal Signal name Condition Resistance (Ω) (pprox.) F Seek (down) Depress. 165 16 17 20 17 Volume (down) Depress VOL down. 487 Mode/end Depress. 0 Seek (up) Depress. 165 Volume (up) Depress VOL up. 487 WKI4457E G H Phone/send Depress. 0 Do the steering wheel audio control es check OK? YES >> GO TO 2 NO >> Replace steering wheel audio control. Refer to V-88, "Removal and Installation". 2.CHECK HRNESS 1. Disconnect luetooth control unit harness connector 141 and spiral cable harness connector M30. 2. Check continuity between luetooth control unit harness connector 141 () and spiral cable harness connector M30 (). Connector Terminal Connector Terminal 12 24 141 13 M30 32 14 31 Continuity 3. Check continuity between luetooth control unit connector 141 () and ground. Yes LNI0735G I J K L M V Connector 141 re the continuity results as specified? YES >> GO TO 3 NO >> Repair harness. 3.SPIRL CLE CHECK Terminal 12 13 14 Continuity Ground No O P V-53
STEERING SWITCH < COMPONENT DIGNOSIS > [PREMIUM UDIO (KING C)] 1. Disconnect spiral cable connector M102. 2. Check continuity between spiral cable harness connector M30 () and M102 (). Connector Terminal Connector Terminal Continuity 24 20 M30 31 M102 17 Yes 32 16 Does the spiral cable check OK? YES >> Inspection End. NO >> Replace spiral cable. Refer to SR-6, "Removal and Installation". WNI0797ZZ V-54
COMMUNICTION SIGNL CIRCUIT < COMPONENT DIGNOSIS > [PREMIUM UDIO (KING C)] COMMUNICTION SIGNL CIRCUIT STELLITE RDIO TUNER STELLITE RDIO TUNER : Description INFOID:0000000003301795 Communication signals are exchanged between the audio unit and satellite radio tuner using the communication circuits. STELLITE RDIO TUNER : Diagnosis Procedure INFOID:0000000003301796 C 1.CHECK HRNESS - REQ1 1. Turn ignition OFF. 2. Disconnect satellite radio tuner (factory installed) connector M41 and audio unit connector M42. 3. Check continuity between satellite radio tuner (factory installed) harness connector M41 () terminal 28 and audio unit harness connector M42 () terminal 48. Continuity Connector Terminal Connector Terminal M41 28 M42 48 Yes 4. Check continuity between satellite radio tuner (factory installed) harness connector M41 () terminal 28 and ground. Connector Terminal Continuity M41 28 Ground No re continuity results as specified? YES >> GO TO 2 NO >> Repair harness or connector. 2.CHECK HRNESS - TXD 1. Check continuity between satellite radio tuner (factory installed) harness connector M41 () terminal 29 and audio unit harness connector M42 () terminal 49. Continuity Connector Terminal Connector Terminal M41 29 M42 49 Yes 2. Check continuity between satellite radio tuner (factory installed) harness connector M41 () terminal 29 and ground. Connector Terminal Continuity M41 29 Ground No re continuity results as specified? YES >> GO TO 3 NO >> Repair harness or connector. 3.CHECK HRNESS - RXD LNI0709G LNI0707G D E F G H I J K L M V O P V-55
COMMUNICTION SIGNL CIRCUIT < COMPONENT DIGNOSIS > [PREMIUM UDIO (KING C)] 1. Check continuity between satellite radio tuner (factory installed) harness connector M41 () terminal 30 and audio unit harness connector M42 () terminal 50. Continuity Connector Terminal Connector Terminal M41 30 M42 50 Yes 2. Check continuity between satellite radio tuner (factory installed) harness connector M41 () terminal 30 and ground. LNI0708G Connector Terminal Continuity M41 30 Ground No re continuity results as specified? YES >> GO TO 4 NO >> Repair harness or connector. 4.CHECK REQ1 SIGNL 1. Connect satellite radio tuner (factory installed) connector and audio unit connector. 2. Turn ignition to CC 3. Check signal between satellite radio tuner (factory installed) harness connector M41 terminal 28 and ground with CONSULT-III or oscilloscope. Connector (+) Terminal (-) Reference signal M41 28 Ground WKI4544E SKI3825E re voltage readings as specified? YES >> GO TO 5 NO >> Replace audio unit. Refer to V-84, "Removal and Installation". 5.CHECK TXD SIGNL Check signal between satellite radio tuner (factory installed) harness connector M41 terminal 29 and ground with CONSULT-III or oscilloscope. Connector (+) Terminal (-) Reference signal M41 29 Ground WKI4545E re the voltage readings as specified? SKI3824E V-56
COMMUNICTION SIGNL CIRCUIT < COMPONENT DIGNOSIS > [PREMIUM UDIO (KING C)] YES >> GO TO 6 NO >> Replace satellite radio tuner. 6.CHECK RXD SIGNL Check signal between satellite radio tuner (factory installed) harness connector M41 terminal 30 and ground with CONSULT-III or oscilloscope. Connector (+) Terminal (-) Reference signal C D M41 30 Ground WKI4546E E SKI3826E re the voltage readings as specified? YES >> Replace satellite radio tuner. Refer to V-95, "Removal and Installation". NO >> Replace audio unit. Refer to V-84, "Removal and Installation". F G H I J K L M V O P V-57
SOUND SIGNL CIRCUIT < COMPONENT DIGNOSIS > [PREMIUM UDIO (KING C)] SOUND SIGNL CIRCUIT STELLITE RDIO TUNER STELLITE RDIO TUNER : Description INFOID:0000000003301797 Left and right channel audio signals are supplied from the satellite radio tuner to the audio unit through the sound signal circuits. STELLITE RDIO TUNER : Diagnosis Procedure LEFT CHNNEL 1.CHECK HRNESS 1. Turn ignition OFF. 2. Disconnect satellite radio tuner (factory installed) connector M41 and audio unit connector M42. 3. Check continuity between satellite radio tuner (factory installed) connector M41 () and audio unit connector M42 (). INFOID:0000000003301798 Continuity Connector Terminal Connector Terminal 21 41 M41 M42 Yes 22 42 4. Check continuity between satellite radio tuner (factory installed) connector M41 () and ground. LNI0710G Connector M41 Terminal 21 22 Continuity Ground re continuity results as specified? YES >> GO TO 2 NO >> Repair harness or connector. 2.CHECK LEFT CHNNEL UDIO SIGNL 1. Connect satellite radio tuner (factory installed) and audio unit. 2. Turn ignition ON. 3. Check signal between satellite radio tuner (factory installed) connector M41 terminals 21 and 22 with CONSULT-III or oscilloscope. No Connector (+) Terminal (-) Reference signal 21 M41 22 Ground WKI4548E SKI3609E re voltage readings as specified? YES >> Replace audio unit. Refer to V-84, "Removal and Installation". NO >> Replace satellite radio tuner. Refer to V-95, "Removal and Installation". RIGHT CHNNEL V-58