HP-2 Recessed Wall Wash Flush Tech Zone /Independent Scan QR code for helpful video(s) Step 1 Step 2 Tech Zone Collection. Center-to-center spacing Wall 0-10V Dimming.0.0.0 Tech Zone (C1) Tech Zone (C2) Tech Zone (C2T).0.0 Tech Zone (C3) Tech Zone (C3F) Remove diffuser from starter and set aside to prevent it from getting dirty or damaged. We recommend using a thin flat tool such as a putty knife. Configure to luminaire size and leave an opening for luminaire as noted above. Make sure s are aligned at 90 degrees. Position luminaires properly to illuminate the wall. Step 3 Step Tie-wire (by others) Step 5 Place starter luminaire on. Brackets #8-18 x 1/ Finelite, Inc. 30500 Whipple Road Union City, CA 9587-1530 (510) 1-1100 Fax: (510) 1-1510 www.finelite.com 1 Use #8-18 x 1/ screws to attach brackets to luminaire. Then secure luminaire to structure by using tie-wire (by others), as per code. Washer Lock Dimming (gray) Dimming (purple) Remove conduit plate from end of luminaire and insert conduit through conduit plate. Secure conduit with washer lock. 2016 FINELITE, INC. ALL RIGHTS RESERVED. Form 98336 V2. 11/16
HP-2 Recessed Wall Wash Flush Tech Zone /Independent OPTIONAL SPLICE BOX Step 6 #8-18 x 1/ Screws (2) Conduit Jam Nut Wires #8-18 x 1/ Screws (2) Wires Splice Box Door Open optional splice box door to access wiring. Splice Box Door Run power cable through knock-out. Make electrical connection. Secure conduit on to splice box with jam nut and close splice box door. Make electrical connections and reinstall conduit plate to luminaire. Step 7 Step 8 Brackets #6-20 x 1/2" Self Drilling Screws () Secure luminaire to by driving #6-20 x 1/2" self drilling screws through the brackets into the. Finelite, Inc. 30500 Whipple Road Union City, CA 9587-1530 (510) 1-1100 Fax: (510) 1-1510 www.finelite.com 2 Align Here Reinstall diffuser by A. Aligning it to the back plate as shown. B. Then press the side with a snap lobe into the luminaire until it snaps. Turn power on to luminaire. A B Lobe 2016 FINELITE, INC. ALL RIGHTS RESERVED. Form 98336 V2. 11/16
HP-2 Recessed Wall Wash Flush Tech Zone Scan QR code for helpful video(s) Step 1 Step 2 Ground Wire/Safety Straps 0-10V Dimming Back Plate Harness #8-18 x 1/ Self Drilling Screws #8-18 x 1/ Remove diffuser from joiner/ender and set aside to prevent it from getting dirty or damaged. We recommend using a thin flat tool such as a putty knife. Unplug LED harnesses. Remove extruded carrier by backing out only the two shown #8-18 x 1/ screws (one per side of the extrusion). They do not need to be removed. There are two ground wire/safety straps that the back plate assembly will hang from. Only remove the back plate that is adjacent to the joint. Step 3 Tech Zone (C1).0 Tech Zone (C3) Tech Zone Collection. Center-to-center spacing Configure to luminaire size and leave an opening for luminaire as noted above. Make sure s are aligned at 90 degrees. Position luminaires properly to illuminate the wall..0 Tech Zone (C2).0 Tech Zone (C3F).0 Tech Zone (C2T) Finelite, Inc. 30500 Whipple Road Union City, CA 9587-1530 (510) 1-1100 Fax: (510) 1-1510 www.finelite.com 1 Wall.0 Step Place luminaire on.
HP-2 Recessed Wall Wash Flush Tech Zone Step 5 Step 6 Step 7 IMPORTANT STEP Plug-Together Wiring Tie-wire (by others) Brackets Joint Sleeve #8-18 x 1/ Yoke Brackets (2) #10-32 x 5/8" Screws (2) Connect plug-together wiring. Align starter and joiner/ender and slide them together. Use #8-18 x 1/ screws to attach brackets to luminaire. Then secure luminaire to structure by using tie-wire (by others), as per code. IMPORTANT STEP: Secure joint with two yoke brackets using #10-32 x 5/8" screws. CAUTION: When installed correctly these brackets will pull luminaires together to make a tight joint. Do not over-tighten. Step 8 Step 9 Brackets #6-20 x 1/2" Self Drilling Screws Secure all luminaires to by driving #6-20 x 1/2" self drilling screws through the brackets into the. Harness Ground Wire/Safety Straps Finelite, Inc. 30500 Whipple Road Union City, CA 9587-1530 (510) 1-1100 Fax: (510) 1-1510 www.finelite.com 2 Back Plate #8-18 x 1/ Replace all back plates to starter and joiner/ender, and secure with #8-18 x 1/ screws. Plug in LED harnesses. #8-18 x 1/
HP-2 Recessed Wall Wash Flush Tech Zone IMPORTANT STEP Step 10 Step 10a Step 10b Step 11 Joiner Joiner Lobe Joiner Joiner Align Here A B IMPORTANT STEP: Install kick plate joiner at the joint of the luminaires by A. Rotating the kick plate joiner and B. Tipping it into the back plate over the kick plates at the joint. Reinstall diffuser: A. Aligning it to the back plate as shown. B. Press the side with a snap lobe into the luminaire until it snaps. Turn power on to luminaire. Finelite, Inc. 30500 Whipple Road Union City, CA 9587-1530 (510) 1-1100 Fax: (510) 1-1510 www.finelite.com 3