PRODUCT INFORMATION GUIDE IMAGESTAR SILICONE INK 3500 Series RFU Textile Inks 1500 Series Pigment Concentrate Textile Inks
COMPONENTS ImageStar 3500 Series RFU Silicone Ink Ready-For-Use Colors Color Gold IMS35610 Light Orange IMS35600 Bright Orange IMS35602 Burnt Orange IMS35606 Texas Orange IMS35604 National Red IMS35620 Crimson IMS35630 Light Maroon IMS35840 Purple IMS35662 Navy Blue IMS35684 Royal Blue IMS35220 Columbia Blue IMS35680 Color Aqua Kelly Green Dark Green Silver Gray Dark Gray Vegas Gold Old Gold Dark Brown Opaque Black Opaque White Underbase Gray* Masking Black** IMS35682 IMS35692 IMS35694 IMS35262 IMS35264 IMS35612 IMS35614 IMS35842 IMS35240 IMS35750 IMS35260 IMS35245 ImageStar 1500 Series Pigment Concentrate Silicone Ink Additives Bases Colorants Description Clear used for mixing fluorescents or HD printing IMS2100 Description Opaque used for mixing PMS colors (contains retarder) IMS3102 ImageStar additives are compatible with both 1500 Series Color Concentrate Inks and 3500 Series RFU Inks. Description Catalyst Retarder IMS2200 IMS2201 Color Blue 1 White Tint Black Tint Orange Yellow Violet Blue 2 Green Magenta IMS1522 IMS1558 IMS1559 IMS1560 IMS1561 IMS1566 IMS1568 IMS1569 IMS1583 Color Maroon Fluorescent Pink Fluorescent Green Fluorescent Yellow Fluorescent Red Fluorescent Purple Fluorescent Blue Strong Black Strong White IMS1584 IMS1590 IMS1592 IMS1594 IMS1595 IMS1598 IMS1599 IMS1524 IMS1575 Refer to the mixing recommendations on page 4 for information about incorporating catalyst or retarder with ImageStar Silicone Inks. 2 ImageStar Silicone 3500 Series and 1500 Series Textile Inks 3500 Series colors not visually represented above: Underbase Gray (IMS35260 RFU), Opaque White (IMS35750 RFU) and custom colors. Printed results of colors may vary based on production. Ink film thickness, opacity, pigment selection and substrate can all affect results. *Only needed as underbase for extremely problematic dye-migrating fabrics. ** For use as an underbase when printing on dye sublimated fabrics. Additional information can be found in Masking Black technical data sheet. Only needed to make printing black and white. Not needed if using 3500 Series RFU black and white.
The ImageStar Silicone 3500 RFU and 1500 Color System Textile Ink Series are developed for printing on performance wear and smooth polyester fabrics. The ImageStar Silicone PVC free inks exhibit superior elasticity and durability when printed on these demanding fabric types. Manufactured with a retarder addition, the inks maximize screen open time of the catalyzed product. This results in a very productionfriendly printing ink that can run up to 6 hours with minimal screen drying issues. The 3500 Series is a ready-for-use ink consisting of 23 standard colors. The 1500 Series is a base-plus-concentrate system allowing for color customization. Both the 3500 and 1500 Series are catalyzed using the 2200 Silicone Catalyst and feature low curing temperature which greatly reduces the potential for dye migration. FEATURES 100% polyester PERFECT FOR PERFORMANCE WEAR PERFECT FOR PERFORMANCE WEAR EXCELLENT SCREEN OPEN TIME IIIIIIIIIIIIIIIIIIIII 6 EXCELLENT SCREEN OPEN TIME CONVENIENT PACKAGING quarts gallons CONVENIENT PACKAGING These inks feature a very low curing temperature which greatly reduces the potential for dye migration. Also the perfect choice for printing on digital dye-sublimated camouflage performance wear. Manufactured with a retarder addition to maximize the screen open time of the catalyzed product resulting in a very production-friendly printing ink that can run up to 6 hours with minimal screen drying issues. Colors are stocked in quart and gallon containers. PVC free ENVIRONMENTALLY FRIENDLY EXCELLENT PRINTABILITY HEAT RESISTANT GREAT AESTHETICS ENVIRONMENTALLY FRIENDLY EXCELLENT PRINTABILITY HEAT RESISTANT GREAT AESTHETICS Contains no PVC, phthalates, solvents, organotins, azo-dyes, or formaldehyde. Prints through a wide range of mesh. 110-156 mesh is recommended for stretch and athletic apparel. 156-305 mesh can be used for fine detail. The printed image can be ironed and will not melt. Features a soft, matte finish with very low to non-tack feel. Extreme elongation properties for elastic fabrics. SourceOne.Nazdar.com 3
MIXING Recommended Mixing Ratios for 1500 Series The ImageStar 1500 Series Pigment Concentrates can be added to the base material up to a maximum of 30% by weight. A 20% addition is recommended in most formulations. Always pre-test for cure and adhesion prior to production run. Add the catalyst just prior to production to maximize the pot life of the ImageStar silicone ink. See recommendations for adding catalyst below. If catalyst is added during the color blending process, and the print production is delayed, seal the container air-tight and store in a cool, dry environment until use. Recommendations for Adding Catalyst The catalyst is the key component for curing the ImageStar Silicone Inks. The reaction of the catalyst to the base material results in the cross linking of the silicone components; this cross linking will continue until a completely cured ink film is achieved. 3% to 5% by weight of the IMS2200 Silicone Catalyst must be mixed into the 3500 Series RFU or 1500 Series Color Concentrate ink colors prior to printing. The catalyst can be manually weighed and mixed by hand or by using a mechanical mixer. The catalyst should be added and mixed with the RFU silicone right before the printing process. Only catalyze the quantity of ink you will use during an 8-hour shift of printing. The catalyzed ink pot life is primarily determined by ambient room temperature. Higher temperatures result in shorter pot life. On press, humidity has little effect on pot life of the catalyzed printing ink. Extended pot life of catalyzed inks that are not in screen can be achieved by covering the ink container and keeping in a cool location. Do not place containers near flash units. Recommendations for Adding Retarder The 1500 Series Opaque Base (item number IMS3102) and all of the 3500 Series RFU silicone ink colors already contain an addition of retarder. The retarder slows the curing process during printing; additional retarder may be needed when printing production occurs in hot environmental conditions or long printing times (>8 hours) are required. In most environments, additional retarder will not be required. The normal cross linking could begin to occur after about 45 minutes of printing; retarder allows the ink to remain screen stable and printable through an 8-hour shift. Use an additional 1% - 3% of IMS2201 Silicone Retarder by weight as needed. 4 ImageStar Silicone 3500 Series and 1500 Series Textile Inks
Printing Recommendations Printing the ImageStar Silicone Ink is not different from most other textile printing inks. When printing on dark substrates, the silicone ink can be flash cured, and colors can be printed on top of the flash plate (similar to plastisol ink processes). Depending on the artwork, wet-on-wet printing can be achieved using finer mesh counts and less ink deposit. Screen Mesh To achieve a smooth print surface, 110-156 mesh is recommended for stretch and athletic apparel. 156-305 mesh can be used for fine detail. Stencil A good EOM (emulsion over mesh) ratio with an even shirt side coating surface helps to ensure a consistent and smooth ink deposit. Utilize a quality high solids emulsion and incorporate a 2/2 coating procedure, finishing on the squeegee side of the screen. Capillary films (100-200 micron) can be used to increase the thickness of the printed ink film if desired. Squeegee 70 durometer or 60/90/60 triple durometer. Lower durometer squeegee, increased angle, and slower print speed will result in increased ink deposit for optimal opacity. Pallets Preheat the pallets to 140 F (60 C) prior to production. Flash The ImageStar Silicone ink will typically flash dry at temperatures of 180-200 F (82-93 C). Flash times are normally achieved in 4-6 seconds. For fabrics containing high levels of elastic fibers (15%- 20%) or fabrics with poor sublimation fastness, the ink surface temperature should be kept below 212 F (100 C) to prevent fabric damage or contamination from migrated dyestuff. Adding Ink to Screen Add only enough ink to be able to print for 2-3 hours. Add additional ink in small increments throughout the print run to allow for a continuous printing operation. Extreme Climates When the ambient air temperature is extremely hot, use fans on screens to keep ink cooler and add a cool down station after flash as needed. Machine Stop When the machine stops for a break, the image area must be flooded with a thick layer of silicone ink to protect the ink from curing in the mesh openings. For longer breaks: Best practice is to remove the ink from the screens and store in covered container. Wipe down the screens with solvent. Optionally, clean the image area with solvent and cover the screen with a plastic bag. End of Print Run It is recommended to use as much of the ink in the screen as possible as the production run winds down to reduce waste. Do not remove the catalyzed ink from the screen and add it back to un-catalyzed product. It is also not recommended to remove the ink from the screen and reuse it. The excess ink will continue to cross link until hardened. Screen Cleaning/Clean Up Clean the screen right after the printing operation is complete, as the ink will continue to cross link and cure with time. Uncured catalyzed ImageStar Silicone inks can generally be removed from the screens and equipment with the same cleaning agents used to remove plastisol inks. In addition, hydrocarbon-based solvents such as mineral spirits can be used. PRINTING SourceOne.Nazdar.com 5
CURING & STORAGE Curing Recommendations After printing, the printed image should be oven cured at 248-284 F (120-140 C) for one to two minutes to ensure full cure and wash fastness. For heat sensitive fabrics or for energy saving purposes, lower temperatures can be used for longer dwell times. Materials such as tin complexes, sulfur and amines are known to interfere with curing so contamination by these must be avoided. Pre-treatment of printed fabric with an amino-silicone softener will result in an incomplete cure. Dark garment colors such as blacks, browns, and dark blues may contain sulfur dyes and can inhibit the silicone ink from curing thus resulting in insufficient adhesion. Avoid any potential for cross-contamination with PVC containing products. It is recommended that ImageStar Silicone inks are printed and cured on a production line that is dedicated strictly to the use of silicone inks. Screen printing pallets must be free of any non-silicone ink residue. Even a slight PVC plastisol ink deposit on the pallet can release plasticizer under heat that will inhibit the curing of the silicone ink. Storage Recommendations It is extremely important to test all fabrics for adequate adhesion before beginning a production run. Store original unopened containers at or below 86 F (30 C). Ink taken from the press should not be returned to the original container to avoid contamination and curing of fresh ink. Store unused catalyzed inks in closed containers at cool temperatures (~77 F or 25 C). The ink can be kept for extended periods (up to several days) and reused when necessary. Cooler temperatures (~45 F or 7 C) can result in longer useable life of product. Do not place ink from screen back into the container containing unused catalyzed inks or risk affecting pot life of unused inks. Relative humidity has little effect on pot life of the catalyzed printing ink, however, if un-catalyzed IMS Silicone Inks are exposed to humid air during storage, the pot life of the subsequently catalyzed ink will be shortened, even when no significant changes in viscosity are noticed. To avoid shortening of pot life, the containers of ImageStar Silicone Inks must be sealed well. Once the containers are opened, a PE, PP, or PVDC film should be placed over and in contact with the un-catalyzed printing ink to prevent moisture absorption and then sealed appropriately. This helps prevent moisture from coming into contact with the silicone ink. ImageStar Silicone inks have a usable life of 12 months from the date of manufacture when stored at or below the recommended temperature of 86 F (30 C). 6 ImageStar Silicone 3500 Series and 1500 Series Textile Inks
Special Considerations for Printing on Cotton and Blends As a general rule, silicone inks do not exhibit good fiber mat down properties. Therefore, printing on hairy fabrics such as some 100% cotton or brushed polyesters garments is not recommended. The standard smoothing screen process as utilized in plastisol printing on the flashed underbased ink is not effective as the silicone ink is not thermoplastic and will not re-melt. A smooth print surface on these fabrics can be achieved by utilizing a multi-step printing process: Print the underbase, apply a Teflon sheet to the wet ink film. Print the smoothing screen and flash cure. Finally remove the Teflon sheet. The resultant print will be significantly glossier than standard. If you have in-line heat press capabilities, or if you are manually printing, the following method can be used: Apply a Teflon coating to a heat press/hot plate and set the temperature to 250-300 F (120-150 C). Print the underbase, apply the heat press for ~10 seconds. Print the additional colors on top of the pressed underbase. The resultant print will be significantly glossier than standard. An effective process for less severe fabrics is simpler: Print a thin neutral ink film layer (160-180 mesh) as an underbase. The IMS3102 Base can be used. A fast squeegee stroke will lay minimal material down to seal the air space between the garment fibers. Flash Print ImageStar Silicone white/color on top of neutral flash plate through coarser (110-140) mesh. CONSIDERATIONS For more information about this product or to place your order, visit us online at SourceOne.Nazdar.com or scan the code with your smart phone SourceOne.Nazdar.com 7
SourceOne.Nazdar.com cserv@nazdar.com 888-578-5713 2016 Nazdar. All Rights Reserved. SourceOne, CATZper and ImageStar are registered trademarks of Nazdar. All other trademarks are the property of their respective owners. Pricing and specifications are subject to change without notice. S1LIT0104 v01042016