CERTIFICATE OF ACCREDITATION ANSI-ASQ National Accreditation Board 500 Montgomery Street, Suite 625, Alexandria, VA 22314, 877-344-3044 This is to certify that Micro Precision Calibration 5909 Breckenridge Parkway, Suite B Tampa FL 33610 has been assessed by ANAB and meets the requirements of international standard ISO/IEC 17025:2005 and national standards ANSI/NCSL Z540-1-1994 (R2002) and ANSI/NCSL Z540.3-2006 (R2013) while demonstrating technical competence in the field of CALIBRATION Refer to the accompanying Scope of Accreditation for information regarding the types of calibrations to which this accreditation applies. AC-1969.26 Certificate Number Certificate Valid: 07/31/2017-10/31/2018 Version No. 001 Issued: 07/31/2017 This laboratory is accredited in accordance with the recognized International Standard ISO/IEC 17025:2005. This accreditation demonstrates technical competence for a defined scope and the operation of a laboratory quality management system (refer to joint ISO-ILAC-IAF Communiqué dated April 2017).
SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005, ANSI/NCSL Z540-1-1994 (R2002), AND ANSI/NCSL Z540.3-2006 (R2013) Micro Precision Calibration 5909 Breckenridge Parkway, Suite B Tampa, FL 33610 Norma Vasquez 530-268-1860 norma.vazquez@microprecision.com CALIBRATION Valid to: October 31, 2018 Certificate Number: AC-1969.26 Electrical DC/Low Frequency Parameter / DC Voltage Generate DC Voltage Measure 1 DC Current Generate 1 Up to 220 mv 220 mv to 2.2 V (2.2 to 11) V (11 to 22) V (22 to 220) V (220 to 1100) V (0 to 100) V 100 mv to 1V (1 to 10) V (10 to 100) V (100 to 1 000) V (1 to 10) kv (10 to 20) kv (21 to 70) kv (0 to 220) µa 220 4 µa to 22 ma (22 to 220) ma 220 ma to 2.2 A (2.2 to 11) A (1 to 500) A 10 µv/v + 0.5 µv 6 µv/v + 0.8 µv 4 µv/v + 3 µv 4 µv/v + 4.5 µv 4 µv/v + 4 µv 4 µv/v + 5 µv 6.1 µv/v + 0.3 µv 5 µv/v + 0.3 µv 5 µv/v + 0.5 µv 7.3 µv/v + 30 µv 26 µv/v + 100 µv 0.1 % + 0.004 kv 0.3 % of reading 0.6 % of reading 41 na/a + 7 na 34 na/a + 8 na 35 na/a + 45 na 46 na/a + 0.8 µa 82 na/a + 13 µa 0.26 % of reading Fluke 5720A HP 3458A Vitrek 4700 Fluke 5720A w/option 03 w/ 50 turn coil Page 1 of 12
Parameter / DC Current Measure 1 Up to 100 na 100 na to 1 µa (1 to 10) µa (10 to 100) µa 100 µa to 10 ma (10 to 100) ma 100 ma to 1 A 35 µa/a + 400 µa 25 µa/a + 40 µa 25 µa/a + 10 µa 25 µa/a + 5 µa 25 µa/a + 5 µa 40 µa/a + 5 µa 0.012 % + 10 µa HP 3458A High DC Current (1 to 100) A 0.04% of reading Shunt w/3458a Resistance Generate 1 Resistance Generate 1 Fixed Points Up to 11 Ω (11 to 33) Ω (33 to 110) Ω (110 to 330) Ω (0.33 to 1.1) kω (1.1 to 3.3) kω (3.3 to 11) kω (11 to 33) kω (33 to 110) kω (110 to 330) kω 0.33 kω to 1.1 MΩ (1.1 to 3.3) MΩ (3.3 to11) MΩ (11 to 33) MΩ (33 to 110) MΩ (110 to 330) MΩ 330 MΩ to 1.1 GΩ 1.9 Ω 10 Ω 19 Ω 100 Ω 190 Ω 1 kω 1.9 kω 10 kω 19 kω 100 kω 190 kω 0.12 % of reading + 0.008 Ω 0.17 % of reading 0.018 % of reading 0.024 % of reading 90 % of reading + 0.06 Ω 0.024 % of reading 0.009 % + 0.6 Ω 0.012 % of reading 0.011 % + 6 Ω 0.013 % of reading 0.015 % of reading + 55 Ω 0.019 % of reading 0.016 % of reading 0.041 % of reading 0.058 % of reading 0.37 % of reading 1.8 % of reading 0.009 1 % of reading 0.002 4 % of reading 0.002 4 % of reading 0.001 % of reading 0.001 % of reading 0.000 85 % of reading 0.000 85 % of reading 0.000 85 % of reading 0.000 85 % of reading 0.001 % of reading 0.001 % of reading Fluke 5720A w/option 03 Page 2 of 12
Parameter / Resistance Generate 1 Fixed Points Resistance Measure 1 Capacitance Generate 1 Inductance Generate 1 Fixed Points: 1kHz Electrical Calibration of Thermocouple Indicators 1 1 MΩ 1.9 MΩ 10 MΩ 19 MΩ 100 MΩ (1 to 10) Ω (10 to 100) Ω 100 Ω to 100 kω 100 kω to 1 MΩ (1 to 10) MΩ (10 to 100) MΩ 100 MΩ to 1 GΩ (0.33 to 0.49) nf (0.50 to 1.09) nf (1.10 to 3.29) nf (3.30 to 10.9) nf (11.0 to 32.9) nf (33 to 109.9) µf (110 to 329.9) µf (0.33 to 1.09) µf (1.10 to 3.29) µf 5 mh 100 mh 1 H Type E (-250 to -100) C (-100 to 650) C (650 to 1 000) C Type J (-210 to -100) C (-100 to 760) C (760 to 1 200) C Type K (-200 to -100) C (-100 to 120) C (120 to 1 000) C (1 000 to 1 372) C 0.001 8 % of reading 0.001 8 % of reading 0.003 7 % of reading 0.004 6 % of reading 0.01 % of reading 19 µω/ω + 60 µω 15 µω/ω + 0.6 mω 13 µω/ω + 0.6 mω 18 µω/ω + 2.4 Ω 59 µω/ω + 120 Ω 0.057 % of reading + 1.1 kω 0.057 % of reading + 11 kω 3.3 % of reading 1.4 % of reading 0.73 % of reading 0.51 % of reading 0.54 % of reading 0.32 % of reading 0.32 % of reading 0.29 % of reading 0.37 % of reading 0.059 % of reading 0.062 % of reading 0.082 % of reading 0.57 C 0.18 C 0.24 C 0.31 C 0.19 C 0.26 C 0.37 C 0.18 C 0.29 C 0.04 C Fluke 5720A w/option 03 HP 3458A Genrad 1482 series Page 3 of 12
Parameter / Electrical Calibration of Thermocouple Indicators 1 Type S (0 to 250) C (250 to 1 400) C (1 400 to 1 767) C Type T (-250 to -150) C (-150 to 0) C (0 to 400) C Pt 385, 100 Ω (-200 to 0) C (0 to 100) C (100 to 400) C (400 to 630) C (630 to 800) C Pt 3926, 100 Ω (-200 to 0) C (0 to 100) C (100 to 400) C (400 to 630) C Pt 3916, 100 Ω (-200 to -190) C (-190 to 0) C (0 to 300) C (300 to 600) C (600 to 630) C Pt 385, 200 Ω (-200 to 100) C (100 to 260) C (260 to 600) C (600 to 630) C Pt 385, 500 Ω (-200 to 100) C (100 to 260) C (260 to 600) C (600 to 630) C 0.53 C 0.42 C 0.52 C 0.71 C 0.27 C 0.16 C Electrical Simulation of RTD Indicating Systems 1 0.05 C 0.07 C 0.1 C 0.12 C 0.23 C 0.05 C 0.07 C 0.1 C 0.12 C 0.25 C 0.05 C 0.08 C 0.1 C 0.23 C 0.04 C 0.05 C 0.14 C 0.16 C 0.05 C 0.06 C 0.09 C 0.11 C Page 4 of 12
Parameter / Electrical Simulation of RTD Indicating Systems 1 AC Voltage Generate 1 Pt 385, 1 kω (-200 to 100) C (100 to 260) C (260 to 600) C (600 to 630) C PtNi 385, 100 Ω (-80 to 100) C (100 to 260) C Cu427, 10 Ω (-100 to 260) C (0 to 220) mv (20 to 40) Hz 40 Hz to 20 khz 100 khz to 1 MHz 220 mv to 2.2 V (20 to 40) Hz 40 Hz to 20 khz 100 khz to 1 MHz (2.2 to 22) V (20 to 40) Hz 40 Hz to 20 khz 100 khz to 1 MHz (22 to 220) V (20 to 40) Hz 40 Hz to 20 khz 100 khz to 1 MHz 0.03 C 0.05 C 0.07 C 0.23 C 0.08 C 0.14 C 0.3 C 0.055 % + 13 μv 0.021 % + 8 μv 0.011 % + 8 μv 0.037 % + 8 μv 0.085 % + 25 μv 0.34 % + 80 μv 0.05 % + 80 μv 0.016 % + 25 μv 75 µv/v + 6 μv 0.012 % + 16 μv 0.025 % + 70 μv 0.22 % + 850 μv 0.05 % + 0.8 mv 0.016 % + 0.25 mv 75 µv/v + 0.06 mv 0.012 % + 0.16 mv 0.025 % + 0.35 mv 0.34 % + 8.5 mv 0.05 % + 8 mv 0.016 % + 2.5 mv 80 µv/v + 0.8 mv 0.022 % + 3.5 mv 0.05 % + 8 mv 0.27 % + 190 mv Fluke 5720A w/option 03 Page 5 of 12
Parameter / AC Voltage Generate 1 AC Voltage Measure 1 AC Voltage Measure 1 (220 to 750) V (20 to 40) Hz 40 Hz to 20 khz 100 khz to 300 khz (220 to 1100) V (15 to 50) Hz 50 Hz to 1 khz Up to 10 mv (1 to 40) Hz 40 Hz to 1 khz (1 to 20) khz (100 to 300) khz 10 mv to 10 V (1 to 40) Hz 40 Hz to 1 khz (1 to 20) khz (100 to 300) khz 300 khz to 1 MHz (1 to 2) MHz (10 to 100) V (1 to 40) Hz 40 Hz to 1 khz (100 to 300) khz 300 khz to 1 MHz (100 to 1000) V (1 to 40) Hz 40 Hz to 1 khz (1 to 20) khz 0.05 % + 8 mv 0.016 % + 2.5 mv 80 µv/v + 0.8 mv 0.022 % + 3.5 mv 0.05 % + 8 mv 0.2 % + 90 mv 0.04 % + 16 mv 90 µv/v + 4 mv 0.03 % + 3 μv 0.02 % + 2 μv 0.03 % + 2 μv 0.12 % + 2 μv 0.58 % + 2 μv 4.6 % + 2 μv 80 µv/v + 0.4 mv 80 µv/v + 0.2 mv 0.02 % + 0.2 mv 0.03 % + 0.2 mv 0.09 % + 0.2 mv 0.35 % + 1 mv 1.2 % + 1 mv 1.7 % + 1 mv 0.02 % + 4 mv 0.02 % + 2 mv 0.04 % + 2 mv 0.14 % + 2 mv 0.46 % + 10 mv 1.7 % + 10 mv 0.05 % + 40 mv 0.05 % + 20 mv 0.07 % + 20 mv 0.14 % + 20 mv 0.35 % + 20 mv Fluke 5720A w/option 03 HP 3458A HP 3458A, synchronous sub- sampled mode Page 6 of 12
Parameter / AC Voltage Measure 1 (50 to 60) Hz AC Current Generate 1 40 Hz to 1 khz AC Current Generate 1 AC Current Generate 1 (50 to 70) Hz AC Current Measure 1 Oscilloscope 1 Level Sine Amp (1 to 10) kv (10 to 50) kv (1 to 220) μa 220 μa to 22 ma (22 to 220) ma 220 ma to 2.2 A (2.2 to 11) A 45 Hz to 65Hz 65 Hz to 500Hz 500 Hz to 1kHz 0.2 % + 0.025 kv 0.6 % + 0.11 kv 0.026 % + 9.1 na 0.023 % + 400 na 0.024 % + 2.8 µa 0.038 % + 40 µa 0.097 % + 2 000 µa 0.15 % + 2 000 µa 0.43 % + 2 000 µa Vitrek 4700 Fluke 5720 w/option 03 (0 to 500) A 0.26 % w/50 turn coil Up to 100 μa (20 to 45) Hz 45 Hz to 1 khz 100 μa to 100 ma (20 to 45) Hz (45 to 100) Hz 100 Hz to 5 khz 100 ma to 1 A (20 to 45) Hz (45 to 100) Hz 100 Hz to 5 khz 0.46 % + 0.03 µa 0.18 % + 0.03 µa 0.068 % + 0.03 µa 0.46 % + 20 µa 0.17 % + 20 µa 0.068 % + 20 µa 0.034 % + 20 µa 0.46 % + 200 µa 0.19 % + 200 µa 0.1 % + 200 µa 0.12 % + 200 µa (1 to 100) A (50 to 400) Hz 2.6 % 5 mv to 5 Vp-p 50 khz Reference 50 khz to 100 MHz (100 to 300) MHz (300 to 600) MHz 2 % + 300 µv 3.5 % + 300 µv 4 % + 300 µv 6 % + 300 µv HP 3458A Shunt monitored w/ multimeter Fluke 5820A Level Sine Flatness Relative to 50 khz Reference 5 mv to 5.5 V 50 khz to 100 MHz (100 to 300) MHz (300 to 600) MHz 1.6 % + 100 µv 2 % + 100 µv 4 % + 100 µv Page 7 of 12
Parameter / Oscilloscope 1 Square Wave 10 Hz to 10 khz 1 MΩ 50 Ω 1mV to ± 130 V ± 1 mv to ± 6.6 V 0.06 % + 5 µv 0.25 % + 40 µv Time Marker Output Into 50 Ω 2 ns to 20 ms 50 ms to 5 s 0.33 parts in 10 6 s (2.5 parts in 10 6 s) + 5 µhz Fluke 5820A Pulse Rise Time 0.5 V, 1Vp-p Oscilloscope Bandwidth 10 MHz 1 MHz (0 to 6) Vpp (0.05 to 300) MHz (2 to 50) GHz 100 ps 100 ps 72 mv 0.09% of reading HP8482 HP8487A Electrical - RF/Microwave Parameter / RF Tuned Power, Relative Measure 1 (2.5 MHz to 26.5 GHz) RF Power Absolute RF, Measure 1 100 khz to 4.2 GHz 10 MHz to 18 GHz 10 MHz to 18 GHz 10 MHz to 26.5 GHz 10 MHz to 50 GHz (-10 to 0) db (-20 to -10) db (-40 to -10) db (-50 to -40) db (-80 to -50) db (-90 to -80) db (-110 to -90) db (-127 to -110) db (-30 to 20) dbm (-70 to -20) dbm (-30 to 20) dbm (-30 to 20) dbm (-30 to 20) dbm 0.06 db 0.08 db 0.11 db 0.14 db 0.2 db 0.26 db 0.3 db 0.4 db 0.06 dbm 0.09 dbm 0.06 dbm 0.07 dbm 0.08 dbm HP 8902A, HP 11793A HP 438A, 8902A, E4419B w 8482A, 8484A, 8481A, 8485A 8487A Page 8 of 12
Electrical - RF/Microwave Parameter / RF Power Generate 1 10 khz to 20 MHz 20 MHz to 2 GHz (-127 to 13) dbm 1.2 db 1.2 db HP 8657A, HP 83650L (2 to 20) GHz (20 to 50) GHz Amplitude Modulation 1 Measure 150 khz to 10 MHz (-110 to 10) dbm Rate: 50 Hz to 10 khz Rate: 20 Hz to 100 khz Depth:(5 to 99) % 1.3 db 1.9 db 2.5 % Depth 3.6 % Depth HP 8902A 10 MHz to 1300 MHz (1.3 to 26.5) GHz Frequency Modulation 1 Measure 50 Hz to 10 khz Rate: 50 Hz to 50 khz Rate: 20 Hz to 100 khz Depth: (5 to 99) % Rate: 20 Hz to 100 khz Depth: (5 to 99) % Rate: 250 khz to 10 MHz Dev: 40 khz 1.6 % Depth 3.6 % Depth 3.7% Depth 2.5 % Deviation HP 8902A w/11793a HP 8902A 50 Hz to 100 khz 20 Hz to 200 khz Rate: 10 MHz to 1.3 GHz Dev: 400 khz 7.7 % Deviation 1.8 % Deviation 20 Hz to 100 khz 50 Hz to 100 khz Harmonic Measurements 1 30 Hz to 50 GHz Phase Modulation 1 Rate: 200 Hz to 20 khz Rate: (1.3 to 26.5) GHz 7.7 % Deviation 1.8 % Deviation HP 8902A w/ 11793A (-90 to 0) db 1.5 db HP 8565E 10 MHz to 1.3 GHz 3.6 % Deviation HP 8902A Rate: 200 Hz to 20 khz Distortion Measure 1 (50 to 500) khz (1.3 to 26.5) GHz (0 to 99.9) db 20 Hz to 20 khz 4.3 % Deviation 1.3 db HP 8902A with 11793A Agilent 8903B (50 to 500) khz (20 to 100) khz 2.4 db Page 9 of 12
Length Dimensional Metrology Parameter / Calipers 1 (0.1 to 36) in (577 +.9L) µin Gage blocks Height Gages 1 (0.1 to 48) in (46 + 1.2L) µin Gage blocks, surface plate Cylindrical Plug Gages & Pin Universal length measuring Up to 2 in 32 µin Gages machine Thread Plug Gages Universal length measuring Pitch (0.1 to 8) in (62 + 1.2L) µin machine and thread wires Major (0.1 to 8) in (30 + 1.2L) µin Indicators, Resolution 20 µin 50 µin 100 µin Up to 6 in 14 µin 30 µin 74 µin End Measuring Rods (0 to 12) in 24 µin Pin Gages, Diameter (0.02 to 2.00) in (12 + 0.34L) µin Internal Threads Up to 4 in (66 + 1.2L) µin Micrometers 1 Length and Flatness 50 µin 100 µin Up to 8 in Up to 36 in (32 + 10L) µin (66 + 10L) µin Profile Projector/ Measuring Microscope 1 Length (0.1 to 20) in (73 + 1.3L) µin Inspection Fixtures Riser Blocks, Angle Blocks, Straight Edges, Bar Parallels, V-Blocks Up to 24 in Up to 40 in (15 + 1.5L) μin (25 + 1.5L) μin Gage blocks Universal length measuring machine Universal length measuring machine Universal Length Measuring Machine, Gage Blocks Mitutoyo gage blocks CMI long blocks, optical flat, monochromic light source Glass Scales, Gage Blocks Universal Length Measuring Machine, Electric Comparator, Gage Blocks, Granite Surface Plate, Profile Projector, Hand Tools, Inclinometer, Cylindrical Square Page 10 of 12
Mass Parameter / Torque Measuring 1 Scales and Balances 1 Pressure Measuring 1 Pressure Measuring 1 Force Compression and Tension (0 to 400) ozf in (0 to 50) lbf in (0 to 150) lbf in (0 to 400) lbf in (0 to 600) lbf ft Up to 500 mg 500 mg to 200 g (200 to 1 000) g (1 000 to 5 000) g (5 to 20) kg Up to 50 lb (50 to 100) lb (100 to 500) lb (500 to 1 000) lb (-15 to 0.001) psi (0.001 to 100) psi (100 to 1 000) psi (1 000 to 10 000) psi (-7 to 0.0001) in H2O (0.0001 to 7) in H2O (0.0001 to 30 psi (30 to 200) psi (201 to 600) psi (601 to 1500) psi (1501 to 3 000) psi (0.01 to 500) lbf 0.83 % of rdg 0.92 % of rdg 0.7 % of rdg 0.66 % of rdg 0.68 % of rdg 4 µg 0.07 mg 0.8 mg 2 mg 4 mg 0.015 lb 0.03 lb 0.15 lb 1.6 lb 0.1 % of reading 0.1 % of reading 0.09 % of reading 0.15 % of reading 0.01 % of reading 0.01 % of reading 0.0042 % of reading 0.04 % of reading 0.06 % of reading 0.043 % of reading 0.032 % of reading 0.83 % of reading CDI torque system Class 1 weights, Class 2 weights Class F weights Fluke 700 series pressure transducers Heise in H2O Mensor DPI 145 Heise 901A Heise 901B Heise 901B Heise 901B Class F weights with stand Thermodynamic Parameter / Humidity Measuring 1 Temperature Measuring (20 to 90) % RH 1.5 % RH Vaisala HMI41 (-200 to 660) C 0.08 C SPRT Page 11 of 12
Time and Frequency Parameter / Frequency Measuring Frequency 1 Measure 10 MHz 6 10-12 Hz/Hz HP 58503A 0.1 Hz to 225 MHz 2.3 10-11 Hz/Hz GPS, HP 58503B 500 MHz to 40 GHz 5 10-9 Hz/Hz 0.01 Hz to 10 MHz 5.7 10-11 Hz/Hz 10 MHz to 50.0 GHz 1.1 10-11 Hz/Hz Agilent 53132A Agilent 5352B GPS, HP 58503B HP 3325B GPS, HP 58503B Agilent 83650L Calibration and Measurement Capability (CMC) is expressed in terms of the measurement parameter, measurement range, expanded uncertainty of measurement and reference standard, method, and/or equipment. The expanded uncertainty of measurement is expressed as the standard uncertainty of the measurement multiplied by a coverage factor of 2 (k=2), corresponding to a confidence level of approximately 95%. Notes: 1. On-site calibration service is available for this parameter, since on-site conditions are typically more variable than those in the laboratory, larger measurement uncertainties are expected on-site than what is reported on the accredited scope 2. This scope is formatted as part of a single document including Certificate of Accreditation No. AC-1969.26. Page 12 of 12