UNIVERSAL TRAY STAND - SMALL AASFT24 AASLH24 AASLP24
Thank you for purchasing the Active Aqua Universal Tray Stand. This 2 x 4 stand supports Active Aqua 2' x 4' flood tables (and most any other brand of 2' x 4' flood tables) and allows you to move them easily when necessary. WHAT S IN THE BOX FIGURE 1 BOTTOM STAND PARTS LIST (AASFT24) A - Corner Leg (Standard Height) w/casters V1 (2) B - Corner Leg (Standard Height) w/casters V2 (2) C - Side Rail (2) D - End Rail (2) E - Center Support Rail Assembly (1) F - Corner Retainer V1 (2) G - Corner Retainer V2 (2) 2 www.hydrofarm.com
ASSEMBLY INSTRUCTIONS (FOR BOTTOM STAND ONLY AASFT24): Remove all of the parts from the packaging and set the hardware aside. Group all of the stand parts together based on type for ease of locating and assembly, i.e. corner legs together, side rails together, end bars together, etc. All parts will be marked with a letter corresponding to the parts list on page 2. 1. Begin by inserting the Side Rails (Part C) into the Corner Legs V1 (Part A) and Corner Legs V2 (Part B), locking them into position with the spring buttons (see Image 1). Image 1 Image 2 NOTE: Be sure to install the Corner Legs V1 at two opposite corners from each other, and the Corner Legs V2 at the two remaining opposite corners. They must be installed this way or the assembly will be incorrect. NOTE: If you are adding a Light Hanger to your bottom stand, STOP HERE and continue the assembly using the section titled ASSEMBLY INSTRUCTIONS (INCLUDING LIGHT HANGER) (page 4). 2. Next, insert the End Rails (Part D) into the remaining openings in the Corner Legs V1 (Part A) and Corner Legs V2 (Part B), locking them into position with the spring buttons (see Image 2). 3. Connect your 2-Piece Center Support Rail (Part E), locking it into proper position with the spring button (see Image 3). 4. Now you can insert the Corner Retainers V1 and V2 (Parts F & G), placing them as shown in Figure 1 (be sure to place the Corner Retainers V1 at opposite corners to each other and the Corner Retainers V2 at opposite corners to each other as you did with the legs) (see Image 4). Image 3 Image 4 3
LIGHT HANGER PARTS LIST (AASLH24) A1 - Vertical Light Bar (2) B1 - Trellis Bar (2) C1 - Horizontal Light Bar (2) D1 - Butterfly thumb screw (4) E1 - Center Light Bar (1) F1 - Lynch Pin (4) ASSEMBLY INSTRUCTIONS (INCLUDING LIGHT HANGER AASLH24) Remove all of the parts from the packaging and set the hardware aside. Check to be sure that the hardware contains the Lynch Pins (quantity: 4) and Butterfly Thumb Screws (quantity: 4). Group all of the stand parts together based on type for ease of locating and assembly, i.e. corner legs together, side rails together, end bars together, etc. All parts will be marked with a letter corresponding to the parts list above. 4 www.hydrofarm.com
1. Begin by inserting the Side Rails (Part C) into the Corner Legs V1 (Part A) and Corner Legs V2 (Part B), locking them into position with the spring buttons (see Image 1). 2. Install the End Rails (Part D) into the foundation squares of the Vertical Light Bars (Part A1) (see image 6). Secure each end rail and foundation square together with one of the butterfly thumb screws (Part D1). Image 6 Image 7 3. Attach the Horizontal Light Bars (Part C1) to the Vertical Light Bars (Part A1) (see Image 7). 4. Attach Trellis Bars (Part B1) to the Vertical Light Bars (Part A1) and lock them in place using Lynch Pins (Part F1) (see Image 8). 5. Use the second pair of Lynch Pins (Part F1) to adjust the height of the light hanger by inserting them into the appropriate holes in the Vertical Light Bars (Part A1) (see Image 9). Image 8 Image 9 6. To adjoin the two vertical bar sections, insert the Center Light Bar (Part E1) into the Horizontal Light Bars (Part C1) and secure it using both Butterfly Thumb Screws (Part D1) (see Image 10). 7. Complete the assembly by inserting the Corner Retainers V1 and V2 (Parts F & G), placing them as shown in Image 4 (be sure to place the Corner Retainers V1 at opposite corners to each other and the Corner Retainers V2 at opposite corners to each other as you did with the legs). Image 10 5
INSTALLATION OF THE LOW PROFILE LEG KIT NOTE: The below instructions assume that you have already used the standard sized legs and are switching to the low profile legs. If you want to assemble the stand with the low profile legs from the start, simply use the Low Profile Corner Legs V1 and Low Profile Corner Legs V2 in place of the standard length corner legs when assembling the bottom tray stand. Be sure to install the Low Profile Corner Legs V1 at two opposite corners from each other, and the Low Profile Corner Legs V2 at the two remaining opposite corners. They must be installed this way or the assembly will be incorrect. 1. To install the Low Profile Leg Kit, first decouple all four Corner Legs (Parts A & B) from the End Rails (Part D) and Side Rails (Part C) by depressing the spring buttons and pull them away from the Side Rails and End Rails. Image 11 2. Replace the Corner Legs V1 (Part A) with the Low Profile Corner Legs V1 (Part A2) and replace the V2 Corner Legs (Part E) with the Low Profile Corner Legs V2 (Part B2). AASLP24 6 www.hydrofarm.com
7
WARRANTY LIMITED WARRANTY Hydrofarm warrants the AASFT24, AASLH24, AASLP24 to be free from defects in materials and workmanship. The warranty term is for one year beginning on the date of purchase. Misuse, abuse, or failure to follow instructions is not covered under this warranty. Hydrofarm s warranty liability extends only to the replacement cost of the product. Hydrofarm will not be liable for any consequential, indirect, or incidental damages of any kind, including lost revenues, lost profits, or other losses in connection with the product. Some states do not allow limitation on how long an implied warranty lasts or the exclusion of incidental or consequential damages, so the above limitations or exclusions may not apply to you. Hydrofarm will, at our discretion, repair or replace the AASFT24, AASLH24, AASLP24 covered under this warranty if it is returned to the original place of purchase. To request warranty service, please return the AASFT24, AASLH24, AASLP24, with original sales receipt and original packaging, to your place of purchase. The purchase date is based on your original sales receipt. GARANTIE LIMITÉE Hydrofarm garantit que le AASFT24, AASLH24, AASLP24 ne présente aucun défaut de pièces et maind œuvre. La période de garantie est d un an à partir de la date d achat. Une utilisation incorrecte, abusive, ou le non-respect des instructions n est pas couvert(e) par cette garantie. La responsabilité de la garantie Hydrofarm couvre uniquement le coût de remplacement du produit. Hydrofarm ne pourra être tenu responsable des dommages consécutifs, indirects ou fortuits de tout type, y compris les pertes de revenus, de profits ou autres en rapport avec le produit. Certains états n autorisent aucune limite concernant la durée de la garantie implicite ou l exclusion des dommages fortuits ou consécutifs ; les limites ou exclusions mentionnées ci-dessus peuvent donc ne pas être applicables à votre cas. Hydrofarm se réserve le droit de réparer ou remplacer le AASFT24, AASLH24, AASLP24 couvert par cette garantie si celui-ci est renvoyé au lieu d achat d origine. Pour solliciter le service de garantie, veuillez renvoyer le AASFT24, AASLH24, AASLP24 avec sa facture et son emballage d origine à votre lieu d achat. La date d achat est indiquée sur votre facture originale. GARANTÍA LIMITADA Hydrofarm garantiza que el AASFT24, AASLH24, AASLP24 no presentará defectos de fabricación. La garantía tendrá una duración de un año desde la fecha de compra. En caso de no respetarse estas instrucciones o de un uso inadecuado del producto, la garantía no cubrirá los posibles daños. La cobertura de la garantía ofrecida por Hydrofarm únicamente incluye los costes de sustitución del producto. Hydrofarm no será responsable de ningún daño indirecto, accidental o derivado de ningún tipo, incluyendo pérdidas de ingresos o beneficios, o cualquier otra pérdida relacionada con el producto. En algunos estados no se permiten limitaciones sobre la duración de una garantía implícita o la exclusión de los daños accidentales o derivados; en cuyo caso las limitaciones y exclusiones anteriores no serán de aplicación. Hydrofarm, a su discreción, podrá reparar o sustituir el AASFT24, AASLH24, AASLP24 cubierto por esta garantía siempre que se devuelva al lugar original de compra. Para reclamar la garantía, devuelva el AASFT24, AASLH24, AASLP24 con el ticket de compra y el embalaje original al lugar de compra. La fecha de compra será la indicada en el ticket original. 8 www.hydrofarm.com www.hydrofarm.com AASFT24, AASLH24, AASLP24 Instructions revised - November 15, 2016 3:56 PM