Tall Storage Unit ssembly Instructions - Please keep for future reference 33/2536 Dimensions Width - 32.5cm Depth - 30.cm Height - 0cm Important - Please read these instructions fully before starting assembly If you need help or have damaged or missing parts, call the Customer Helpline: 0456 40000 Version 2 Date: 0/09/
Safety and Care dvice Important - Please read these instructions fully before starting assembly Check you have all the components and tools listed on pages 2 and 3. Remove all fittings from the plastic bags and separate them into their groups. eep children and animals away from the work area, small parts could choke if swallowed. Make sure you have enough space to layout the parts before starting. Do not stand on the product, this could cause damage. ssemble the item as close to its final position (in the same room) as possible. ssemble on a soft level surface to avoid damaging the unit or your floor. Parts of the assembly will be easier with 2 people. We do not recommend the use of power drill/drivers for inserting screws, as this could damage the unit. nly use hand screwdrivers. Dispose of all packaging carefully and responsibly. Note: nly apply the glue once you are sure of the assembly. lue safety - Take care when using glue, please follow the advice below Skin contact: Remove contamination by washing with soap and water. This procedure should also be followed prior to eating and drinking. ye contact: Rinse immediately with clean water for 5 minutes and seek medical advice. If swallowed: Seek medical advice immediately. Care and maintenance nly clean using a damp cloth and mild detergent, do not use bleach or abrasive cleaners. rom time to time check that there are no loose screws on this unit. This product should not be discarded with household waste. Take to your local authority waste disposal centre. Note: if required the next page can be cut out and used as reference throughout the assembly. eep this page with these instructions for future reference.
Components - Panels If you have damaged or missing components, call the Customer Helpline: 0456 40000 Please check you have all the panels listed below Pilot holes for guidance only eft side panel (7.4 x 29.9cm) Pilot holes for guidance only 2 Right side panel (7.4 x 29.9cm) Pilot holes for guidance only Pilot holes for guidance only 3 Top panel 4 ottom panel 5 Middle panel 6 Shelf x 2 (32.4 x 30cm) (29.3 x 29.cm) (29.3 x 29.cm) (29.3 x 2.4cm) 7 Top shelf (29.3 x 2.4cm) Pilot holes for guidance only Door x 3 (33 x 2.5cm) 9 ront panel (29.3 x.cm) 0 Top back panel (0.5 x 30cm) ottom back panel (66.4 x 30cm) 2
Components - ittings Note: may be supplied than are required. Wooden dowel x 20 50mm Screw x 4 D 2mm Screw x 3 4mm Screw x 9 C 30mm Screw x 6 5mm Screw x 6 Door stopper x 3 H Handle x 3 I Door hinge x 6 Hinge plug x 3 Screw cover x 4 M Wall strap x (This screw is included in the wall strap bag) x N Wall plug x lue x Plastic support x 4 P Metal plate x 3 Tools required Phillips screwdriver (medium & large) Small hammer radawl (or sharp point) 0 0 20 30 40 50 60 70 0 90 00 0 20 30 40 50 0 2 3 4 5 6 Ruler/tape measure ye protection (when using a hammer or glue) Ruler - Use this ruler to help correctly identify the screws 0 5 0 5 20 25 30 35 40 45 50 55 60 65 70 75 0 5 90 95 00 05 0 5 20 25 30 35 40 45 50 55 60 65 70 3
ssembly Instructions Step itting hinges and handles to doors a: I a: Metal plate Door. P D onto the Insert the Door hinges into the Door. I P D I Handle. H C onto the Door Use the same method as in a+b to assembly another doors. C C H 4
ssembly Instructions Step 2 itting dowels and door stopper a: Caution: lways check the assembly method is correct before applying glue. 5 a: Insert Hinge plug into the Middle panel 5. Place a small amount of lue into the dowel holes. Insert Wooden dowels into the Middle panel 5. s Door stopper Shelf 6. onto the Place a small amount of lue into the dowel holes. Insert Wooden dowels into the Shelf 6. 6 X 2 c: Insert Hinge plug into the Top shelf 7. c: Place a small amount of lue into the dowel holes. Insert Wooden dowels into the Top shelf 7. 7 5
ssembly Instructions Step 3 itting the bottom panel a: a: Place a small amount of lue into the dowel holes. Insert Wooden dowels into the ottom panel 4. 4 Insert Hinge plug into the ottom panel 4. Plastic supports onto the ront panel 9. 9 inished front edge c: ront panel 9 onto the ottom panel 4. c: inished front edge 9 4 roove underneath 6
ssembly Instructions Step 4 itting left side panel a: Place a small amount of lue into the dowel a: panel panel panel. 4 5 and Middle onto eft side using Screws Plastic supports onto the eft side panel. 4 5 Use Screw covers to cover the Screw heads. Place a small amount of lue into the dowel holes. 4 Position Door onto the unit, locating the hinges into plug on ottom panel 4 and Shelf 6 and corresponding hole. 6 c: Place a small amount of lue into the dowel holes. Position Door onto the unit, locating the hinges into plug on Middle panel 5 and Shelf 6 and corresponding hole. c: 5 6 Continued on next page. 7
ssembly Instructions Step 4 - continued d: Place a small amount of lue into the dowel holes. d: Position Top shelf 7 and Shelves 6 onto eft side panel using Screws. Use Screw covers to cover the Screw heads. 6 6 7 Step 5 itting the back panels Note: It would be useful to ask someone to help you at this stage. Place a small amount of lue into the groove. Carefully slide the Top and ottom back panel 0 and onto the unit. 0
ssembly Instructions Step 6 itting the right side panel Place a small amount of lue into the dowel holes and groove. Use side panel unit. 2 onto the 2 Plactic Support onto the Right side panel 2. Use Screw covers to cover the Screw heads. Step 7 itting the top panel a: a: s Door stopper Top panel 3. onto the 3 Place a small amount of lue into the groove. Position Door onto the unit, locating the hinge into the plug on Top shelf 7 & Top panel 3 and corresponding holes. Position Top panel onto the unit using Screws. 3 7 Use Screw covers to cover the screw heads. 3 9
ssembly Instructions Step ixing to wall It is recommended that the M N wall Note: Wall plugs supplied are for solid wall only. be used for your wall, seek professional advice if in doubt M M M N strap M onto the top panel. With help, move unit into position. Top panel Warning: The unit is heavy. ift with care. remove unit. Drill a hole and insert Wall plug N. Warning: efore drilling, check wall for hidden pipes and cables. strap using Screw M. Note: efore use allow the lue to dry for 24 hours and make sure the unit is secure. If you need help or have damaged or missing parts, call the Customer Helpline: 0456 40000 0
uide to - Wall Mounting & ixings Important: When drilling into walls always Important note: If plastic wall plugs are supplied with your product: check that there are no hidden wires or pipes etc. Make sure that the screws and wall plugs being used are suitable for supporting your unit. Consult a qualified tradesperson if you are unsure. Hints: - these are only suitable for use in masonry walls. If you are in any doubt about the correct wall plugs for your wall, seek professional advice. ailure of the product due to responsibility of the installer. Types of walls : eneral rule: lways use a larger screw and wall plug if you are not sure. 2: nsure you use the recommended drill bit to match the wall plug and hole size. 3: nsure you drill the hole horizontally, do not force the drill or enlarge the hole. 4: Take extra care when drilling high walls, ceilings and ceramic tiles. nsure wall plugs are inserted beyond the thickness of the ceramic tiles to avoid the tiles splitting or cracking. 5: drilled hole. You can use one of the following types of wall plug if your walls are made of brick, breeze block, concrete, stone or wood. No. eneral Purpose wall plug No.3 Cavity ixing wall plug No.5 Hammer ixing wall plug enerally aerated blocks should not be used to support heavy loads, use or use with plasterboard partitions or hollow wooden doors. or use with walls stuck with loads, general purpose wall plugs can be used. No.2 Plasterboard wall plug or use when attaching light loads on to plasterboard partitions. Care & Maintenance is secure to the retaining wall. No.4 Cavity ixing-heavy Duty wall plug heavy loads such as shelving, wall cabinets and coat racks. Safety: lways check the fitting and location to ensure your safety in and around the home. No.6 Shield nchor wall plug Heavy loads or use with heavier loads such as TV & Hii speakers and satelite dishes etc. itting: rom time to time check the fitting to ensure the wall plugs or screws do not become loose. Revision 2-7/0/09