Medium Storage Unit ssembly Instructions - lease keep for future reference 833/47 Dimensions Width - 3.5cm Depth - 30.cm Height - 9.cm Important - lease read these instructions fully before starting assembly If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800 Version Date: 6/09/
Safety and Care dvice Important - lease read these instructions fully before starting assembly Check you have all the components and tools listed on pages and 3. Remove all fittings from the plastic bags and separate them into their groups. eep children and animals away from the work area, small parts could choke if swallowed. Make sure you have enough space to layout the parts before starting. Do not stand on the product, this could cause damage. ssemble the item as close to its final position (in the same room) as possible. ssemble on a soft level surface to avoid damaging the unit or your floor. arts of the assembly will be easier with people. We do not recommend the use of power drill/drivers for inserting screws, as this could damage the unit. nly use hand screwdrivers. Dispose of all packaging carefully and responsibly. Note: nly apply the glue once you are sure of the assembly. Glue safety - Take care when using glue, please follow the advice below Skin contact: Remove contamination by washing with soap and water. This procedure should also be followed prior to eating and drinking. ye contact: Rinse immediately with clean water for 5 minutes and seek medical advice. If swallowed: Seek medical advice immediately. Care and maintenance nly clean using a damp cloth and mild detergent, do not use bleach or abrasive cleaners. From time to time check that there are no loose screws on this unit. This product should not be discarded with household waste. Take to your local authority waste disposal centre. Note: if required the next page can be cut out and used as reference throughout the assembly. eep this page with these instructions for future reference.
Components - anels If you have damaged or missing components, call the Customer Helpline: 08456 400800 lease check you have all the panels listed below ilot holes for guidance only eft side panel (7.6 x 9.9cm) 9 ack panel (07.9 x 30cm) ilot holes for guidance only Right side panel (7.6 x 9.9cm) 0 Drawer right Drawer left side panel x side panel x (6. x.5cm) (6. x.5cm) Drawer front 3 Drawer back panel x panel x (8.8 x 6.4cm) (6. x.5cm) 3 Top panel (3.4 x 30cm) 4 Middle panel x (9.3 x 8.4cm) ilot holes for guidance only 4 Drawer bottom panel x (7 x 5.7cm) 5 ottom panel (9.3 x 9.8cm) 6 Shelf (9.3 x 8.4cm) ilot holes for guidance only ilot holes for guidance only 7 Door (8.5 x 33cm) 8 Front panel (9.3 x 8.8cm)
Components - Fittings Note: may be supplied than are required. Wooden dowel x 6 50mm Screw x D mm Screw x 4mm Screw x 9 C 30mm Screw x 4 F 5mm Screw x G Door stopper x H Handle x 3 I Door hinge x J Hinge plug x Screw cover x Glue x M ocking pin x 8 ocking nut x 8 S Wall strap x (This screw is included in the wall strap bag) x N T Wall plug x lastic support x 4 (This screw is included in the runner bag.) R Runner x 4 mm Screw x mm Screw x 4 U Metal plate x Tools required hillips screwdriver (medium & large) Small hammer radawl (or sharp point) 0 0 0 30 40 50 60 70 80 90 00 0 0 30 40 50 0 3 4 5 6 Ruler/tape measure ye protection (when using a hammer or glue) Ruler - Use this ruler to help correctly identify the screws 0 5 0 5 0 5 30 35 40 45 50 55 60 65 70 75 80 85 90 95 00 05 0 5 0 5 30 35 40 45 50 55 60 65 70 3
ssembly Instructions Step Fitting hinges and handle to door a: Metal plate Door 7. U D onto the a: I Insert the Door hinges into the Door 7. I U D 7 I Handle 7. H C onto the Door 7 C C H 4
ssembly Instructions Step Fitting dowels and door stopper a: Caution: lways check the assembly method is correct before applying glue. F G 6 F G a: s Door stopper Shelf 6. F G onto the lace a small amount of Glue into the dowel holes. Insert Wooden dowels into the Shelf 6. lace a small amount of Glue into the dowel holes. Insert Wooden dowels into the Middle panels 4. 4 X 5
ssembly Instructions Step 3 Fitting the bottom panel a: a: lace a small amount of Glue into the dowel holes. Insert Wooden dowels into the ottom panel 5. J 5 J Insert Hinge plug J into the ottom panel 5. lastic supports onto the Front panel 8. 8 Finished front edge c: Front panel 8 onto the ottom panel 5. c: Finished front edge 8 5 Groove underneath 6
ssembly Instructions Step 4 a: ttaching runners a: osition the Runners in from front edge of the Right side panel. Middle hole Slide top of the runners back. 7mm Runners on the Right side panel. Note: The front part of the Runner should be approximately.7cm from the front edge of the panel. Front edge Slide top of the Runners forward. ilot holes for runner position Runners on the Right side panel. Middle hole Front edge Continued on next page. 7
ssembly Instructions Step 4 - continued c: osition the Runners in from front edge of the eft side panel. c: Middle hole Slide top of the runners back. 7mm Runners panel. on the eft side Note: The front part of the Runner should be approximately.7cm from the front edge of the panel. Front edge d: Slide top of the Runners forward. Runners on the eft side panel. d: Middle hole ilot holes for runner position Front edge 8
ssembly Instructions Step 5 Fitting left side panel a: lace a small amount of Glue into the dowel holes. osition ottom panel onto eft side 5 panel using Screws. a: 5 lastic supports onto the eft side panel. Use Screw cover to cover the Screw heads. lace a small amount of Glue into the dowel holes. osition Door 7 onto the unit, locating the hinges into plug on ottom panel 5 and Shelf 6 and corresponding holes. 5 7 6 c: lace a small amount of Glue into the dowel holes. c: osition Middle panels 4 & Shelf 6 onto eft side panel using Screws. Use Screw covers to cover the Screw heads. 6 4 4 Continued on next page. 9
ssembly Instructions Step 6 Fitting the back panel Note: It would be useful to ask someone to help you at this stage. lace a small amount of Glue into the groove. Carefully slide the ack panel 9 onto the unit. 9 Step 67 Fitting the right side panel lace a small amount of Glue into the dowel holes and groove. Use side panel unit. onto the lactic Support onto the Right side panel. Use Screw covers to cover the Screw heads. Step 8 Fitting the top panel lace a small amount of Glue into the groove. Groove underneath Top panel unit. 3 onto the Use Screw covers to cover the screw heads. 3 0
ssembly Instructions Step 9 Drawer assembly a: GC a: Fix Drawer right and left side panels 0 & to Drawer back panel 3 using Screws C. 3 0 GC lace a small amount of Glue into the grooves. Carefully slide the Drawer 4 bottom panel into the unit. 4 c: Screw ocking pins M into the Drawer front panel. c: GM GM Note: Insert ocking pins as far as shown. Do not over tighten. GM GM M d: lace a small of Glue into the groove. osition the Drawer front panel onto the drawer sides. d: together without any gaps. Fix the Handle H onto the Drawer front panel using Screws C. H C Continued on next page.
ssembly Instructions Step 9 - continued e: Insert 4 ocking nuts N into the holes in the drawer sides(they will only insert one way). e: N N N Use a screwdriver to turn ocking nuts N clockwise to lock. Repeat with remaining drawer. N N Step 0 Inserting drawers a: a: Slide the assembled drawers fully onto the runners so the runners butt up against the back of the drawer front. R R R through drawer sides into the runners using Screws R.
ssembly Instructions Step Fixing to wall S T wall Note: Wall plugs supplied are for solid wall only. It is recommended that the S be used for your wall, seek professional advice if in doubt strap S onto the back of top panel. Top panel S S T With help, move unit into position. Warning: The unit is heavy. ift with care. remove unit. Drill a hole and insert Wall plug T. Warning: efore drilling, check wall for hidden pipes and and cables. strap using Screw S. Wall Note: efore use allow the Glue to dry for 4 hours and make sure the unit is secure. If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800 3
Guide to - Wall Mounting & Fixings Important: When drilling into walls always Important note: If plastic wall plugs are supplied with your product: check that there are no hidden wires or pipes etc. Make sure that the screws and wall plugs being used are suitable for supporting your unit. Consult a qualified tradesperson if you are unsure. Hints: - these are only suitable for use in masonry walls. If you are in any doubt about the correct wall plugs for your wall, seek professional advice. Failure of the product due to responsibility of the installer. Types of walls : General rule: lways use a larger screw and wall plug if you are not sure. : nsure you use the recommended drill bit to match the wall plug and hole size. 3: nsure you drill the hole horizontally, do not force the drill or enlarge the hole. 4: Take extra care when drilling high walls, ceilings and ceramic tiles. nsure wall plugs are inserted beyond the thickness of the ceramic tiles to avoid the tiles splitting or cracking. 5: drilled hole. You can use one of the following types of wall plug if your walls are made of brick, breeze block, concrete, stone or wood. No. General urpose wall plug No.3 Cavity Fixing wall plug No.5 Hammer Fixing wall plug Generally aerated blocks should not be used to support heavy loads, use For use with plasterboard partitions or hollow wooden doors. For use with walls stuck with loads, general purpose wall plugs can be used. No. lasterboard wall plug For use when attaching light loads on to plasterboard partitions. Care & Maintenance is secure to the retaining wall. No.4 Cavity Fixing-Heavy Duty wall plug heavy loads such as shelving, wall cabinets and coat racks. Safety: lways check the fitting and location to ensure your safety in and around the home. No.6 Shield nchor wall plug Heavy loads For use with heavier loads such as TV & HiFi speakers and satelite dishes etc. Fitting: From time to time check the fitting to ensure the wall plugs or screws do not become loose. Revision - 7/0/09