PRSSUR TRNSMITTR T SHT FKG...4 The FX 2 pressure transmitter accurately measures gauge pressure and transmits a proportional 4 to 20m signal. The transmitter utilizes a unique micromachined capacitance silicon sensor with state-of-the-art microprocessor technology to provide exceptional performance and functionality. FTURS 1. High accuracy ±0.07% 0.07% accuracy is a standard feature. Fuji s micro-capacitance silicon sensor assures this accuracy for all elevated or suppressed calibration ranges without additional adjustment. 2. Minimum environmental influence The dvance Floating ell design which protects the pressure sensor against changes in temperature, and overpressure substantially reduces total measurement error in actual field applications. 3. Fuji/HRT bilingual communications protocol and FOUNTION fieldbus and Profibus compatibility FX 2 series transmitter offers bilingual communications to speak both Fuji proprietary protocol and HRT. ny HRT compatible devices can communicate with FX 2. Further, by upgrading electronics FOUN- TION fieldbus and Profibus are also available. 4. pplication flexibility Various options that render the FX 2 suitable for almost any process applications include: nalog indicator at either the electronics side or terminal side Full range of hazardous area approvals uilt-in RFI filter and lightning arrester 5-digit L meter with engineering unit Stainless electronics housing 5. urnout current flexibility (Under Scale: 3.2 to 3.8m, Over Scale: 20.8 to 21.6m) urnout signal level is adjustable using Model FXW Hand Held ommunicator (HH) to comply with NMUR N43. 6. ry calibration without reference pressure Thanks to the best combination of unique construction of mechanical parts (Sensor unit) and high performance electronics circuit (lectronics unit), reliability of dry calibration without reference pressure is at equal level as wet calibration. SPIFITIONS Functional specifications Service: Liquid, gas, or vapour Span, range and overrange limit: Type FKG 01 FKG 02 FKG 03 FKG 04 FKG 05 Span limit [kpa] {bar} Min. 1.3 {0.013} 5 {0.05} 30 {0.3} 100 {1} 500 {5} Max. 130 {1.3} 500 {5} 3000 {30} 10000 {100} 50000 {500} Range limit [kpa] {bar} Lower limit Upper limit 130 {0.13} 500 {5} 3000 {30} 10000 {100} 50000 {500} Overrange limit [MPa] {bar} 1 {10} 1.5 {15} 9 {90} 15 {150} 75 {750} Remark: To minimize environmental influence, span should be greater than 1/40 of the max. span in most applications. Lower range limit (vacuum limit) ; Silicone fill sensor: See Fig. 1 Fluorinated fill sensor: 66kPa abs (500mmHg abs) at below 60 onversion factors to different units; 1 MPa=10 3 kpa=10bar=10.19716kgf/cm 2 = 145.0377psi 1kPa=10mbar=101.9716mmH2O =4.01463inH2O Output signal: 4 to 20m with digital signal superimposed on the 4 to 20m signal. SX5-80h ate Oct. 24, 2005
FKG...4 Power supply: Transmitter operates on 10.5V to 45V at transmitter terminals. 10.5V to 32V for the units with optional arrester. Load limitations: see figure below [Ω] 2000 1533Ω Load resistance 1500 1000 500 250 0 600Ω Operating area 24V 45V 10 16.1 50 [ V ] 10.5V Power voltage Note: For communication with HH (1) (Model: FXW), min. of 250 Ω required. Hazardous locations: uthorities Flameproof Intrinsic safety Type n Nonincendive TX x II 2 G x II 1 G x II 3 G - xd II T5/T6 - xia II T4/T5 - xn II T4/T5 Factory lass I II III lass I II III lass I II III Mutual iv. 1 iv. 1 iv. 2 Groups thru. G Groups thru. F Groups thru. G S lass I II III lass I II III lass I II III iv. 1 iv. 1 iv. 2 Groups thru. G Groups thru. G Groups thru. G TIIS x do II+H 2 T4 x ia II T4 Zero/span adjustment: Zero and span are adjustable from the HH (1). Zero and span are also adjustable externally from the adjustment screw (span adjustment is not available with 9th digit code L, P, Q, S ). amping: djustable from HH or local adjustment unit with L display. The time constant is adjustable between 0.12 to 32 seconds. Zero elevation/suppression: Zero can be elevated or suppressed within the specified range limit of each sensor model. Normal/reverse action: Selectable from HH (1). Indication: nalog indicator or 5-digit L meter, as specified. urnout direction: Selectable from HH (1) If self-diagnostic detect transmitter failure, the analog signal will be driven to either Output Hold, Output Overscale or Output Underscale modes. Output Hold : Output signal is hold as the value just before failure happens. Output Overscale : djustable within the range 20.8m to 21.6m from HH (1) Output Underscale : djustable within the range 3.2m to 3.8m from HH 3.2 3.8 4 20 20.8 21.6 [m] Over scale urnout Under scale urnout Normal operating range Probable under range Probable over range Loop-check output: Transmitter can be configured to provide constant signal 3.8m through 21.6m by HH. Temperature limit: mbient: 40 to +85 ( 20 to +80 for L indicator) ( 40 to +60 for arrester option) ( 10 to +60 for fluorinated oil fill transmitter) For explosionproof units (flameproof or intrinsic safety), ambient temperature must be within the limits specified by each standard. Process: 40 to +100 for silicone fill sensor 20 to +80 for fluorinated oil fill sensor Storage: 40 to +90 Humidity limit: 0 to 100% RH ommunication: With HH (1) (Model FXW, consult ata Sheet No. S8-47), following information can be remotely displayed or reconfigured. Note: HH s version must be more than 6.0 (or FXW 1 3), for FX- 2. M onformity:n61326 Items isplay Set Tag No. Model No. Serial No. ngineering unit Range limit Measuring range amping Output mode urnout direction alibration Output adjust v ata Self diagnoses Printer xternal switch lock Transmitter display Linearize Rerange 2 (Note) (1) HH: Hand Held ommunicator
Performance specifications Reference conditions, silicone oil fill, 316SS isolating diaphragms, 4 to 20m analog output in linear mode. ccuracy rating: (including linearity, hysteresis, and repeatability) Max span below 10000kPa model: For spans greater than 1/10 of URL: ±0.07% of span For spans below 1/10 of URL: 0.1 URL ± ( 0.02+0.05 Span )% of span Max span 50000kPa model: For spans greater than 1/10 of URL: ±0.1% of span For spans below 1/10 of URL: 0.1 URL ± ( 0.05+0.05 Span )% of span Stability: ± 0.1% of upper range limit (URL) for 3 years. Temperature effect: ffects per 28 change between the limits of 40 and +85 URL Zero shift: ±(0.075+0.0125 span )% URL Total effect: ±(0.095+0.0125 span )% Overrange effect: Zero shift; 0.2% of URL for any overrange to maximum limit Supply voltage effect: Less than 0.005% of calibrated span per 1V RFI effect: Less than 0.2% of URL for the frequencies of 20 to 1000MHz and field strength 30 V/m when electronics covers on. (lassification: 2-abc: 0.2% span per SM PM 33.1) Step response: Time constant: 0.2s * ) ead time: approximately 0.2s * ) (without electrical damping) *) Faster response is available as option (maximum update rate: 25 times per second). Mounting position effect: Zero shift, less than 0.1kPa {1m bar} for a 10 tilt in any plane. No effect on span. This error can be corrected by adjusting Zero. ielectric strength: 500V, 50/60Hz 1 min., between circuit and earth. Insulation resistance: More than 100MΩ at 500V. Turn-on time: 4 sec. Internal resistance for external field indicator: 12Ω or less Physical specifications lectrical connections: G1/2, 1/2-14 NPT, Pg13.5, or M20 1.5 conduit, as specified. 1-port (standard) or 2-port with each conduit, as spcified. Process connections: 1/4-18 NPT or Rc1/4 on 54mm centers, as specified. Meet IN 19213 Process-wetted parts material: Material code (7th digit in ode symbols) V J H M T L U Process cover (*1) (*1) (*1) (*1) (*1) iaphragm 316L stainless 316L stainless +u coating Wetted sensor body Vent/drain Note: *(1) SS14 per JIS G 5121 Remark: Sensor O-rings: Viton O-ring and teflon gasket selectable vailability of above material design depends on ranges. Refer to ode symbols. Non-wetted parts material: lectronics housing: Low copper die-cast aluminum alloy finished with epoxy/ polyurethane double coating (standard), or (SS14 per JIS G5121), as specified. olts and nuts: r-mo alloy (standard), or 304 stainless (630 stainless for 50MPa unit). Fill fluid: Silicone oil (standard) or fluorinated oil Mounting bracket: 304 stainless nvironmental protection: I IP67 and NM 6/6P Mounting: On 60.5mm (JIS 50) pipe using mounting bracket, direct wall mounting, or direct process mounting. Mass {weight}: Transmitter approximately 3.4kg without options. dd; 0.5kg for mounting bracket 0.8kg for indicator option 4.5kg for stainless housing option 3
FKG...4 Optional features Indicator: plug-in analog indicator (2.5% accuracy) can be housed in the electronics compartment or in the terminal box of the housing. n optional 5-digit L meter with engineering unit is also available. Local adjustment unit with L display: n optional 5-digit L meter with Zero/ Span adjustment function, loop-check function and damping adjustment function, is available. rrester: built-in arrester protects the electronics from lightning surges. Lightning surge immunity: 4kV (1.2 50µs) Oxygen service: Special cleaning procedures are followed throughout the process to maintain all process wetted parts oil-free. The fill fluid is fluorinated oil. hlorine service: The fill fluid is fluorinated oil. egreasing: Process-wetted parts are cleaned, but the fill fluid is standard silicone oil. Not for use on oxygen or chlorine measurement. N specification: Metallic materials for all pressure boundary parts comply with N MR-01-75. STM 7M or L7M bolts and 2HM nuts (lass II) are available. Vacuum service: Special silicone oil and filling procedure are applied. See Fig.1. Optional tag plate: n extra stainless tag with customer tag data is wired to the transmitter. oating of cell: ell s surface is finished with epoxy/polyurethane double coating. Specify if environment is extermely corrosive. [kpa abs] {mbar abs} 101 {1010} Operating pressure 20 {200} 4 {40} Silicone oil (ode:y,g,n) Silicone oil (ode:r) Operating area SSORIS Oval flanges: (Model FFP, refer to ata Sheet No. S6-10) onverts process connection to 1/2-14 NPT or to Rc1/2; in carbon or in 316 stainless. Hand-held communicator: (Model FXW, refer to ata Sheet No. S8-47) Z/S board: Parts No.=ZZPFX4-070 When Z/S board is mounted on the FX 2 amplifier unit, external adjustment screw will be available for zero and span adjustment. The product conforms to the requirements of the lectromagnetic compatibility irective 94/9/ as detailed within the technical construction file number TN513035. The applicable standards used to demonstrate compliance are : MI (mission) N61326 : 1997 lass (standard for Industrial Location) Frequency range Reference MHz Limits standard 30 to 230 230 to 1000 Phenomenon lectrostatic discharge 40d (µv/m) quasi peak, measured at 10m distance 47d (µv/m) quasi peak, measured at 10m distance Test value asic standard ISPR16-1 and ISPR16-2 MI (Immunity) N61326: 1997 nnex (standard for Industrial Location) lectromagnetic field Rated power frequency magnetic field urst Surge 4kV (ontact) 8kV (ir) 80 to 1000MHz 10V/m 80%M (1kHz) 30/m 50Hz 2kV 5kHz 1.2µs/50µs 1kV (Line to line) 2kV (Line to ground) N61000-4-2 N61000-4-3 N61000-4-8 N61000-4-4 N61000-4-5 Performance criteria onducted RF 0.15 to 80MHz 3V 80%M (1kHz) N61000-4-6 Note) efinition of performance criteria : uring testing, normal performance within the specification limits. : uring testing, temporary degradation, or loss of function or performance which is self-recovering. 2.7 {27} -operating area 40 15 60 85 120 Process temperature[ ] Fig. 1 Relation between process temperature and operating pressure 4
O SYMOLS igit 4 6, 7 <onnections> Process connection Rc1/4 Rc1/4 <Span and materials> Span limit Process cover [kpa]{bar}(*2) 1.3 130 {0.013 1.3} 5 500 {0.05 5} 30 3000 {0.3 30} 100 10000 {1 100} 500 50000 {5 500} Oval flange screw M10 (or M12)(*1) M10 (or M12)(*1) M10 (or M12)(*1) M10 (or M12)(*1) escription onduit connection G1/2 ( 1) 1/2-14NPT ( 1) Pg13.5 ( 1) M20 1.5 ( 1) Pg13.5 ( 1) G1/2 ( 2) 1/2-14NPT ( 2) Pg13.5 ( 2) M20 1.5 ( 2) Pg13.5 ( 2) iaphragm +u coating +u coating +u coating +u coating +u coating ombination with 12th digit code ",, P, Q" are not available. Wetted cell body stee stee stee 9 <Indicator and arrester> Indicator rrester Z/S board nalog, 0 to 100% linear scale attached. nalog, custom scale pproval Yes pending for nalog, 0 to 100% linear scale Yes 10th digit nalog, custom scale Yes code "G, H, igital, 0 to 100% J, K, P" igital, custom scale igital, 0 to 100% Yes igital, custom scale Yes igital, 0 to 100% (Local adjustment unit with L display) pproval igital, custom scale (Local adjustment unit with L display) pending for 10th digit igital, 0 to 100% (Local adjustment unit with L display) Yes code ",, G, H, J, K, igital, custom scale (Local adjustment unit with L display) Yes P" Note 1 : (*1) For 50MPa {500bar} units, M12 is provided rather than M10. Note 2 : (*2) 100: 1 turn down is possible, but should be used at the span greater than 1/40 of the maximum span for better performance. Note Note 1 Note 1 Note 1 Note 1 Note 2 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 21 igit No. F KG 0 4 of code S T V W X 1V 1J 1H 1M 1T 1 1L 1U 2V 2J 2H 2M 2T 2 2L 2U 3V 3J 3H 3M 3T 3 3L 3U 4V 4J 4H 4M 4T 4 4L 4U 5V 5J F H L P Q S 1 2 4 5 5
FKG...4 igit escription 10 <pprovals for hazardous locations> (for ordinary locations) TIIS, Flameproof (onduit seal) (vailable for 4th digit code "", "S") TIIS, Flameproof (able gland seal) (vailable for 4th digit code "", "S") FM, Flameproof (or explosionproof) (vailable for 4th digit code "", "T") S, Flameproof (or explosionproof) (vailable for 4th digit code "", "T") TX, Flameproof TIIS, Intrinsic safety (pproval pending) FM, Intrinsic safety and Nonincendive S, Intrinsic safety and Nonincendive TX, Intrinsic safety TX, Type n 11 <Vent/ drain and mounting bracket> Vent/drain Mounting bracket Standard Specify "", or "" for the 7th Standard Yes, stainless digit code "", "L", or "U" Side Side Yes, stainless 12 <Options> xtra SS tag plate Stainless elec. housing oating of cell Yes Yes Yes (*3) Yes Yes Yes Yes Yes Yes Yes Yes Yes 13 <Special applications and fill fluid> Treatment Fill fluid Standard Silicone oil Standard Fluorinated oil egreasing Silicone oil Oxygen service Fluorinated oil (7th digit code "V", "J" only) hlorine service Fluorinated oil (7th digit code "H", "T","", "U") N specification Silicone oil (Not available for 6th digit code "5", 7th digit code "T", "U", 15th digit code "", "") Vacuum service Silicone oil for vacuum use 14 <Sensor O-ring / Gasket> Viton (O-ring) Teflon (gasket) 15 <olt/nut> r-mo alloy hexagon socket head cap screw/carbon nut r-mo alloy hexagon bolt/nut N bolt/nut (STM 193 7M/194 2HM) Not available for 6th digit N bolt/nut (STM 320 L7M/194 2HM) code "5" 304 stainless bolt/304 stainless nut 630 stainless bolt/304 stainless nut vailable for 6th digit code "5" 21 <Other options> (*4) Instruction manual unattached Note Note3 Note4 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 21 igit No. F KG 0 4 of code X G H J K P F Y M N P Q Y W G N R F L Note 3 : (*3) Note 4 : (*4) ostomer tag number can be engraved on standartd stainless name plate. If extra tag plate is required, select "Yes". If other option is not necessary, 21st digit code is blank. In case of 21st digit code is blank, instruction manual attached. ORRING INFORMTION When ordering this instrument, specify. 1. O SYMOLS 2. Measuring range 3. Output orientation (burnout direction) when abnormality is occured in the transmitter. Hold/Overscale (21.6m)/Overscale (3.2m) Unless otherwise specified, output hold function is supplied. 4. Indication method (indicated value and unit) in case of the actual scale (code,h,p,s on 9th digit). 5. Tag No.(up to 26 alphanumerical characters), if required. 6
OUTLIN IGRM (Unit:mm) < 7th digit code : V, J, H, M, T, J > Vent/drain plug (When the vent/drain plug attatched on the upper side of the detector) Note2) In case of 4th digit code... In case of 4th digit code S.V.W.X MTG. Pipe JIS 50 (2) 70 Press. conn. 94.5 In case of 4th digit code T Zero J. screw φ80 105 8 105 10 Up 130 120 43.5 Fastener (Flameproof only) φ80 52.5 own 41 U - bolt M8 4 holes 9 dia. H 38 58 37 etail (Press. conn.) φ18.5 φ7 See Table 1 Vent / drain plug 8 2.5 Note3) 210 (189) etail (onduit conn.) φ15 See Table 1 F (27) 88 With field ind. (option) onduit conn. etail G 1/2 φ13 17 Note1) able gland (option) arth terminal Oval flange screw See Table 1 41.3 onduit conn. 154 59 43 Note3) Side vent (option) 231 (210) lectronics unit Sensor unit 4th digit of the code symbols, S, T, V, W, X onduit conn. Press. conn. F H Oval flange screw G1/2 17 8 Rc1/4 1/2-14NPT 16 5 Pg13.5 8 4.5 M10 M10 M20 1.5 16 5 Pg13.5 8 4.5 Table 1 ONNTION IGRM + K+ K + 4-M8 12 27 70 104 54 Note1) Note2) able gland is supplied in case of flamproof packing type. φ11 cable is suitable. The pressure connector is located on the down side surface of the detector, when the vent / drainplug is attatched on the upper side of the detector. (When the 21st digit of the code symbols :, or ). Note3) In case of 6th digit code 5 7
FKG...4 MTG. Pipe JIS 50 (2) 70 < 7th digit code :, L, U > In case of 4th digit code... U - bolt M8 41.3 94.5 In case of 4th digit code T Zero J. screw φ80 In case of 4th digit code S.V.W.X 8 105 105 10 Up 104 43.5 Fastener (Flameproof only) φ80 52.5 own 4 holes 9 dia. 38 58 40 213 (27) With field ind. 88 onduit conn. able gland (option) Note) onduit conn. 1 etail (Press. conn.) 4th digit code,s φ16 φ12 +0.2 +0.1 2 0-0.1 etail (onduit conn.) φ15 etail φ13 arth terminal 155 60 43 φ4 F H 17 etail 4th digit code,,,, T,V,W,X φ16 See Table 1 G 1/2 Vent / drain plug View from P L.P. 234 P 10 Oval flange screw See Table1 4-M8 12 H.P. 41.3 41 lectronics unit Sensor unit Note 1) φ4 4th digit of the code symbols, S, T, V, W, X onduit conn. F H G1/2 17 8 1/2-14NPT 16 5 Pg13.5 8 4.5 M20 1.5 16 5 Pg13.5 8 4.5 Table 1 Oval flange screw M10 M10 or Press. conn. able gland is supplied in case of flamproof packing type. φ11 cable is suitable. 98 54 70 120 ONNTION IGRM + K+ K + aution on Safety *efore using this product, be sure to read its instruction manual in advance. Head Office Gate ity Ohsaki, ast Tower, 11-2, Osaki 1-chome, Shinagawa-ku, Tokyo 141-0032, Japan http://www.fesys.co.jp/eng Instrumentation iv. International Sales ept. No.1, Fuji-machi, Hino-city, Tokyo, 191-8502 Japan Phone: 81-42-585-6201, 6202 Fax: 81-42-585-6187 http://www.fic-net.jp/eng Information in this catalog is subject to change without notice. Printed in Japan