te7700.tif TE-7700 Series RF Wireless Room Temperature Sensing System The TE-7700 Series RF Wireless Room Temperature Sensing System consists of a TE-7710 Series RF Wireless Temperature and Set Point Transmitter, and a TE-7720 or TE-7730 Series RF Receiver. Together, these components monitor the temperature set point and zone temperature, and transmit this data to the receiver at predefined intervals. The information is translated into a control signal that works directly with a wide variety of Johnson Controls and compatible competitors digital controllers in Heating, Ventilating, and Air Conditioning (HVAC) systems. The TE-7700 Series RF Wireless Room Temperature Sensing System uses 900 MHz spread-spectrum technology to prevent accidental and unauthorized interference, and to provide better propagation characteristics within the building. Field-addressable DIP switches establish a unique, secure address between each transmitter and receiver. The TE-7700 system provides indication of RF signal strength and low battery. Indication of zone bus communication is also provided on the TE-7720 Series RF Receiver. To optimize comfort in larger zones, a single receiver can average the measured temperature of up to four transmitters in the zone, or select the highest or lowest measured temperature of the zone. Optional signal strength site survey tools are available to determine the appropriate location of the RF wireless temperature sensing system, prior to its installation. These fast-update, 5-second interval tools verify that the RF signal strength is sufficient to ensure proper operation. Refer to the TE-7700 Series Radio Frequency (RF) Wireless Room Temperature Sensing System Product Bulletin (LIT-1201503) for important product application information. te7700s_rf 1900182 9thcc:na Rev: 10/02/02 logo: TE-7700 Series Radio Frequency (RF) Wireless Room Temperature Sensing System Features RF wireless design allows for quick, economical, and low-maintenance installation, reducing total installed cost improved application flexibility provides an alternative to hardwired room temperature sensing counterparts, especially in installations where building aesthetics (such as solid walls or ceilings, temporary walls, or decorative surfaces) would normally hinder hardwiring 900 MHz spread-spectrum technology prevents accidental and unauthorized interference, and provides better propagation characteristics within the building works with Johnson Controls AS-AHU, AS-UNT, AS-VAV, DX-9100, VMA1400, and compatible competitors digital controllers, establishing a new platform for room temperature sensing communications field-addressable DIP switches establish a unique, secure address between each transmitter and receiver multiple transmitter temperature averaging and high/low selection optimizes comfort in larger zones since a single receiver can average the measured temperature of up to four transmitters in the zone, or select the highest or lowest measured temperature of the zone three-level RF signal strength Light-Emitting Diode (LED) integral to the receiver provides visual indication of adequate RF signal strength in nominal 60-second intervals, and minimizes the need for pre-installation signal strength measurements using a site survey tool zone bus activity LED (TE-7720-0 only) provides direct, visual indication of communication between the receiver and the VMA1400 Series Digital Controller low battery indication (via zone bus for TE-7720-0; via low battery relay binary output and LED for ) provides battery condition to warn supervisory equipment in advance when the battery needs to be replaced manual occupancy override pushbutton signals the receiver that the zone is occupied, to override time-of-day scheduling one-to-one control approach enhances reliability by reducing susceptibility to signal interference and by preventing a single point of failure in multiiple zone applications nominal 60-second transmissions provide optimal HVAC control, while conserving battery life universal mounting provides added flexibility since the temperature transmitter may be easily relocated after initial installation optional fast-update, 5-second transmission interval signal strength site survey tools (available to determine the appropriate temperature sensing system location prior to installation) provide quick assurance of a strong RF transmission signal for proper operation Applications The TE-7700 Series RF Wireless Temperature Sensing System is ideal for installations where building aesthetics would normally hinder hardwiring. Recommended applications for this RF wireless system are numerous and include the following: museums, historical buildings, atriums, or other sites where building retention and its historical preservation are important office buildings, university campuses, educational facilities, correctional facilities, and other structures that incorporate brick or solid concrete walls and/or ceilings buildings featuring marble, granite, glass, mirrored, wood veneer, or other decorative surfaces that present significant challenges when attempting hardwiring office buildings, retail stores, and other commercial real estate where tenant turnover is frequent and temporary walls and ceilings are common stadiums, arenas, gymnasiums, convention centers, airports, zoos, and other locations that feature large, open spaces buildings containing asbestos walls or other biohazards that cannot be disturbed To Order Specify the code number from the selection chart on the following page. 1/6 left ft: right ft: standard Sect# = 0 seq# = 1
te77_matrix.eps Features and Options Ordering Matrices for RF Wireless Transmitters and RF Receivers Selection Chart: Transmitter and Receiver Models Available Code Number TE-7710-0N (a) TE-7710-1N (a) TE-7710-1B (a) TE-7710-2N (a) TE-7710-2B (a) TE-7720-0 (b) (b) (a) Includes one 3.0-volt lithium battery. (b) Configured and commissioned using either HVAC PRO software (Release 8.04B or later; AS-AHU, AS-UNT, AS-VAV, and VMA1400 Series Digital Controllers only), or GX-9100 Programming Tool (Release 7.02 or later; DX-9100 Series Digital Controllers only) and GX-9100 Commissioning Tool (Release 8.04 or later; DX-9100 Series Digital Controllers only). Accessories/Repair Parts Code Number RF Wireless Transmitter, No Set Point Adjustment, No Liquid Bulb Thermometer Indication RF Wireless Transmitter, Warmer/Cooler Set Point Adjustment, No Liquid Bulb Thermometer Indication RF Wireless Transmitter, Warmer/Cooler Set Point Adjustment, with Liquid Bulb Thermometer Indication RF Wireless Transmitter, Temperature Set Point Adjustment Scaled 55 to 85 F (13 to 29 C), No Liquid Bulb Thermometer Indication RF Wireless Transmitter, Temperature Set Point Adjustment Scaled 55 to 85 F (13 to 29 C), with Liquid Bulb Thermometer Indication RF Receiver for TE-7710 Series Transmitters, Includes 6 ft (1.8 m) Cable to Connect Power and Zone Bus Interface Between Receiver and Johnson Controls VMA1400 Series Digital Controllers RF Receiver for TE-7710 Series Transmitters, Includes 6 ft (1.8 m) Cable to Connect Power and Analog Interface Between Receiver and Johnson Controls AS-AHU, AS-UNT, AS-VAV, DX-9100, and Compatible Competitors Digital Controllers Duracell Ultra 123, Panasonic CR123A, Toshiba CR123A, GE/Sanyo CR123A, or Equivalent TE-7710-100 TE-7720-100 TE-77DO-601 TE-77DO-602 CBL-STAT25 CBL-STAT50 CBL-STAT75 CBL-STAT100 GRD10A-608 T-4000-119 Replacement Battery (Purchase Locally), 3.0-Volt Lithium Battery (One Required for Transmitter, One Required for Transmitter Signal Strength Site Survey Tool, and Three Required for Receiver Signal Strength Site Survey Tool) RF Wireless Transmitter Signal Strength Site Survey Tool (For Use wiith TE-7720-100 RF Wireless Receiver Signal Strength Site Survey Tool) RF Wireless Receiver Signal Strength Site Survey Tool (For Use wiith TE-7710-100 RF Wireless Transmitter Signal Strength Site Survey Tool) RF Wireless Transmitter Door Replacement Kit with Johnson Controls Logo (10 per Kit) RF Wireless Transmitter Door Replacement Kit without Johnson Controls Logo (10 per Kit) 25 ft (7.6 m) Interface Cable (a) 50 ft (15.2 m) Interface Cable (a) 75 ft (22.9 m) Interface Cable (a) 100 ft (30.5 m) Interface Cable (a) Plastic Guard with Baseplate and Mounting Ring Allen-Head Adjustment Tool (30 per Bag) (a) To connect zone bus between TE-7720 Series RF Receiver and Johnson Controls VMA1400 Series Digital Controllers (does not include power cable). 2/6
te7720.eps TE-7710 Series RF Wireless Temperature and Set Point Transmitter, TE-7720 Series RF Receiver with Zone Bus Interface, and Johnson Controls VMA1400 Series Digital Controller 3/6
te7730.eps TE-7710 Series RF Wireless Temperature and Set Point Transmitter, TE-7730 Series RF Receiver with Analog Interface, and Johnson Controls AS-AHU, AS-UNT, AS-VAV, DX-9100, or Compatible Competitors Digital Controller HVAC PRO Applications that Support the TE-7720-0 and RF Receivers Application Group Name RF Receiver TE-7720-0 Air Handlers 100% OA Dual Path Dual Duct Hot/Cold Deck Reset Air Handlers 100% OA Dual Path Dual Duct Zone Control Yes Air Handlers 100% OA Dual Path Multizone Hot/Cold Deck Reset Air Handlers 100% OA Dual Path Multizone Zone Control Yes Air Handlers 100% OA Single Path Constant Discharge Air Temperature Air Handlers 100% OA Single Path Exhaust Air Temp Control Air Handlers 100% OA Single Path Room Control Yes Air Handlers 100% OA Single Path Room Control Cooling/Room Reset Heating Yes Air Handlers 100% OA Single Path Supply Air Reset from Zone Temperature Yes Air Handlers MA Dual Path Dual Duct Hot/Cold Deck Reset 4/6
HVAC PRO Applications that Support the TE-7720-0 and RF Receivers Application Group Name RF Receiver TE-7720-0 Air Handlers MA Dual Path Dual Duct Zone Control Yes Air Handlers MA Dual Path Multizone Hot/Cold Deck Reset Air Handlers MA Dual Path Multizone Zone Control Yes Air Handlers MA Single Path Constant Discharge Air Temperature Air Handlers MA Single Path Return Air Control Air Handlers MA Single Path Room Control Yes Air Handlers MA Single Path Room Control Cooling/Room Reset Heating Yes Air Handlers MA Single Path Supply Air Reset from Return Temperature Air Handlers MA Single Path Supply Air Reset from Zone Temperature Yes Central Plant Applications Pump Lead/Lag Control Commercial Zoning Applications Damper Assembly (VAV) Yes Commercial Zoning Applications Damper Assembly (VMA) Commercial Zoning Applications Rooftop (UNT) (a) Yes Generic Input/Output Point Multiplexer (b) Yes N2 Dial Applications N2 Dial Module Configuration Rooftop Applications Packaged Rooftop Yes Terminal Unit Applications Fan Coil Yes Terminal Unit Applications Heat Pump Yes Terminal Unit Applications TC Fan Coil Terminal Unit Applications Unit Vent Yes VAV Applications Dual Duct Yes VAV Applications Single Duct Yes VAV Applications VMA Dual Duct VAV Applications VMA Single Duct Yes (a) Only the UNT11xx Series has enough binary inputs to support the battery status for this application. (b) The user must define a sideloop with the appropriate ranging to use the for this application. Interfaces, Applications, and Features for the TE-7720-0 and RF Receivers RF Receiver TE-7720-0 Interface Zone Bus Output 0 to 5 VDC Analog Output Applications (See table above for supported HVAC PRO applications.) Works with Johnson Controls VMA-1400 Series Digital Controllers Works with Johnson Controls AS-AHU, AS-UNT, AS-VAV, DX-9100, and Compatible Competitors Digital Controllers Power On and RF Signal Strength Indication Via RF Signal LED Via RF Signal LED Zone Bus Activity Via Zone Bus LED N/A Zone Temperature Via Zone Bus Via 0 to 5 VDC Analog Output Temperature Set Point Via Zone Bus Via 0 to 5 VDC Analog Output (If Required) Low Battery Indication Via Zone Bus Via Low Battery Relay Binary Output and Low Battery LED Occupancy Status Via Zone Bus Via Occupancy Relay Binary Output (If Required) Specifications Digital Controller Interface Power Requirements Addressing (Transmitter, Receiver, and Site Survey Tools) TE-7700 Series RF Wireless Room Temperature Sensing System TE-7720-0 Power and Zone Bus Interface Between TE-7720-0 RF Receiver and VMA1400 Series Digital Controllers Power and Analog Interface Between RF Receiver and AS-AHU, AS-UNT, AS-VAV, DX-9100, and Compatible Competitors Digital Controllers One 3.0-Volt Lithium Battery Included with Each Transmitter; Battery Life: 36 Months Typical (24 Months Transmitter Minimum); Battery Condition Transmitted Approximately Every 60 Seconds (a) Receiver 24 VAC +10%/-15%, 50/60 Hz, 4.5 VA, Class 2 Transmitter Site Survey Tool One 3.0-Volt Lithium Battery Included with Each Site Survey Tool (a) Receiver Site Survey Tool Three 3.0-Volt Lithium Batteries Included with Each Site Survey Tool (a) DIP Switches, Field Adjustable for Up to 510 Unique Addresses (For addresses 0 and 511, the TE-7720-0 TE-7720-0 matches the N2 address of the associated VMA1400 for its actual address.) DIP Switches, Field Adjustable for Up to 510 Unique Addresses (Addresses 0 and 511 are invalid.) (a) Replacement batteries: Duracell Ultra 123, Panasonic CR123A, Toshiba CR123A, GE/Sanyo CR123A, or equivalent (purchase locally). 5/6
System Accuracy Transmitter Sensor Transmitter Temperature Indicator Transmitter Temperature Set Point Transmission Range (Transmitter, Receiver, and Site Survey Tools) Transmissions Receiver Outputs Mounting Hardware Ambient Operating Temperature Limits Specifications TE-7700 Series RF Wireless Room Temperature Sensing System Measured Temperature ±1F (±0.6C ) Over a Range of 55 to 85 F (13 to 29 C); ±1.5F (±0.9C ) Over a Range of 32 to 55 F (0 to 13 C) and 85 to 110 F (29 to 43 C) Temperature Set Point ±1.5F (±0.9C ) Over a Range of 55 to 85 F (13 to 29 C) Internal Negative Temperature Coefficient Thermistor Type Liquid-Filled Bulb Thermometer Range 55 to 85 F or 13 to 29 C Resolution Fahrenheit Scale Graduated in 10F Intervals; Celsius Scale Graduated in 5C Intervals Adjustment Single Temperature, Scaled F/ C Resolution Fahrenheit Scale Graduated in 5F Intervals; Celsius Scale Graduated in 2C Intervals 1 Mile or 5,280 ft (1,609.3 m) Maximum in Open Air; 1,000 ft (304.8 m) Maximum for Indoor Line-of-Sight; 200 ft (61 m) Practical Average Indoors Transmitter Every 60 Seconds (±20 Seconds) Site Survey Every 5 Seconds (±2 Seconds) Tools TE-7720-0 One Zone Bus Output for Temperature, Set Point, Field Strength Measurements, and Low Battery Indication Two Analog Outputs for Zone Temperature and Set Point: 0 to 5 VDC, 2 ma Maximum; Two Binary Outputs for Occupancy and Low Battery Indication: Dry Contacts Rated for 24 VAC, 50 ma Maximum Transmitter Two Expandable Wall Anchors (Preferred Mounting Method) or Double-Sided Adhesive Foam Tape Receiver Four No. 6 Sheet Metal Screws Transmitter and Transmitter 0 to 122 F (-18 to 50 C) Site Survey Tool Receiver and Receiver Site 32 to 122 F (0 to 50 C) Survey Tool Ambient Storage Temperature Limits -40 to 160 F (-40 to 71 C) (Transmitter, Receiver, and Site Survey Tools) Ambient Humidity Limits Operating 5 to 95% RH, Noncondensing (Transmitter, Receiver, Storage 5 to 90% RH, Noncondensing and Site Survey Tools) Materials Compliance Receiver Terminations Cable Between Receiver and Johnson Controls Digital Controller Dimensions (L x W x H) Transmitter and Transmitter NEMA 1 White Plastic Housing Site Survey Tool Receiver and Receiver Site Gray Plastic Housing with UL94-5VB Flammability Rating Survey Tool Intended for NEC Class 2 Connection UL Listed, File E107041, CCN PAZX UL94-5VB Flammability Rating (Receiver Housing is Plenum Rated per UL 1995, Heating and Cooling United States Equipment) FCC Compliant to CFR 47, Part 15, Subpart B, Class A Transmission Complies with FCC Part 15.247 Regulations for Low Power Unlicensed Transmitters (Transmitter FCC Identification: L2V AX630) Intended for CEC Class 2 Connection UL Listed, File E107041, CCN PAZX7 Canada UL94-5VB Flammability Rating (Receiver Housing is Plenum Rated per CSA C22.2 No. 236, Heating and Cooling Equipment) Industry Canada (Transmitter Industry Canada Identification: IC 279A-TE7710XX) Australia and New Zealand Australia/NZ Emissions Compliant (C-Tick Mark) TE-7720-0 Two Spade Terminals that Accept One Two-Position, Screw-Terminal Pluggable Block (b) TE-7720-0 Eight Spade Terminals that Accept One Two-Position and Two Three-Position, Screw-Terminal Pluggable Blocks (b) 6 ft (1.8 m) Power and Zone Bus Interface Cable Included with Each Receiver; Maximum Recommended Cable Length: 300 ft (91.4 m) Cables to Connect Zone Bus Only (No Power) Measuring 25 ft (7.6 m), 50 ft (15.2 m), 75 ft (22.9 m), and 100 ft (30.5 m) are Available 6 ft (1.8 m) Power and Analog Interface Cable Included with Each Receiver; Maximum Recommended Cable Length: 100 ft (30.5 m) Transmitter and Transmitter 3-3/16 in. x 3-3/16 in. x 1-13/32 in. (81 mm x 81 mm x 36 mm) Site Survey Tool Receiver and Receiver Site 4-23/32 in. x 5-29/32 in. x 1-31/32 in. (120 mm x 150 mm x 50 mm) Survey Tool (b) (a) Pluggable Replacement block(s) batteries: included Duracell with Ultra receiver. 123, Panasonic CR123A, Toshiba CR123A, GE/Sanyo CR123A, or equivalent (purchase locally). 6/6