Connector mated condition Mated height comparison (compared to conventional company products) Fig.1 Features 1. A low mated height of 1.2mm max. When connected, K.FL2 delivers a world class low mated height of 1.2mm. (Refer to Fig.1) 2. High frequency transmission This sereis offers the high performance needed to meet the requirements of many different miniature devices, featuring a DC to 6GHz capacity. 3. Automatic board placement This product is available in embossed packaging; this allows the plug and receptacles to be automatically mounted 4. Design to prevent wrong placement Different shape of shell and contact can prevent wrong placement with easy checking polarization. Product Specifications Ratings Nominal characteristic impedance Frequency range 50Ω DC to 6GHz Operating Temperature Range Storage Temperature Range -40 to +90 (RH 90% or less) -40 to +90 (RH 90% or less) Items 1.Contact resistance 2.V.S.W.R.( ) 3.Insulation resistance 4.Withstanding voltage Specifications(Plug type) 20mΩ (Inner), 20mΩ (Outer) at 10mA DC 1.3 max(dc~3ghz) 1.45max.(3GHz~6GHz) 500MΩmin. At 100V DC 200V AC r.m.s. for 1 minute V.S.W.R. Measurement System (plug type) The above V.S.W.R. specification values were measured using the measurement system shown below. Network Test Test Analyzer Set Port Test Port Cable D.U.T Termination Note1 : Cable type connectors were measured with SMA conversion adapters attached to both ends of the harness product of a suitable 100cm cable. Note2 : Board type connectors were mounted to a 50 glass epoxy board and measurements were conducted with SMA conversion adapters attached. 1
Cable Assembly (Plug) K.FL2-LP-040(Applicable cable : outer diameter (Ø0.81 or Ø0.64) Material/Finish Part Materials Finish and Remarks Shell Phosphor bronze Au plating Insulator PBT Black/UL94V-0 Contact Phosphor bronze Au plating * NOTE : This product satisfies halogen free requirements defined as 900ppm maximum chlorine. 900ppm maximum bromine and 1500ppm maximum total of chlorine and bromine. Cable Guide Description ф0.81mm Coaxial Cable ф0.64mm Coaxial Cable Cable Type 04 044 Center Conductor 7/0.05(36AWG) Silver plated annealed copper wire 7/0.05(36AWG) Silver plated annealed copper wire Dielectric Diameter ф0.40 ф0.44 Cable Specification Outer Conductor Single-layer braided wire Tin plated Fiber or paper coverd copper winding wire Tin plated How to Specify Plug Cable Assembly Jacket Diam eter ф0.81 ф0.64 Nominal Impedance 50 50 Nominal attenuation 3GHz 6GHz 5.8dB 5.8dB 9.4dB 9.4dB The dimensions of a cable assembly of the K.FL2 series should be specified as follows: [Double-Ended Cable Assembly] [Single-Ended Cable Assembly] Single ended assemblies come with a blunt cut on the non-terminated end. Please contact us if special strip requirements are needed. 2
Product Number Structure Refer to the charts below for determining specific part number characteristics. Please select connectors listed in this catalog when placing orders and be sure to check the latest delivery specifications at the time of ordering the product. Used Plug : K.FL2-LP-040 Ø0.81 Coaxial Cable Double-Ended Single-Ended K.FL2-2LP-0.4H [] T-A-(L) K.FL2- LP- 0.4H [] T-A-(L) 1Series Name: 2 Assembly type LP : Single-ended, 2LP : Double-ended 3Cable type 04H : Ø0.81 coaxial cable 4Cable color 1:White, 4:Blue, 6:Red 5Cable outer conductor T: Tin plated braided wire 6Total length L(mm) L length in mm Ø0.64 Coaxial Cable Double-Ended Single-Ended K.FL2-2LP-044H [] TS-A-(L) K.FL2-LP-044H [] TS-A-(L) 1Series Name: 2 Assembly type LP : Single-ended, 2LP : Double-ended 3Cable type 044H : Ø0.64 coaxial cable 4Cable color 1:White, 4:Blue, 6:Red 5Cable outer conductor TS : Tin plated fiber or paper covered copper winding wire 6Total length L(mm) L length in mm Standard Tolerances for (L) L(mm) Standard Tolerances(mm) 35 L 200 ±4 200 L 500 ±8 L(mm) Standard Tolerances(mm) 500 L 1000 ±12 1000< L ±1.5% 3
Receptacles Recommended PCB Mounting Pattern(*1) *1) The pattern is the same as the W.FL and W.FL2 connectors. Part No. HRS No. Packaging RoHS K.FL2-R-SMT-1(800) Reel packaging 10,000 pieces per reel Embossed Carrier Tape Dimensions(JIC-C-0806 compliant) Reel Dimensions 4
Usage Precautions 1.Plugs (1) Allowable load to a cable that is mated After the connector is mated, do not apply a load to the cable in excess of the values indicated in the figure below. When the cable is routed in such a direction that lifts the cable, it is recommended that cushioning should be placed on the plug to prevent the connector from unmating(see the example below) (2)Precautions Do not mate or unmate a connector with an excessive prying force. It may cause a failure of the connector. 5
2. Reflow conditions of receptacles and plug receptacles (1)Recommended reflow Soldering profile for lead free solder(reference) temperature profile[reference] (2)Recommended metal mask thickness (3)Reflow cycles 1. The temperatures indicated are the surface temperatures on the printed circuit board at the points of contact with the terminals. 2. Reflow soldering should be performed at a peak temperature of 250 or less at the surface of the printed circuit board. 3. The temperature profile varies depending on conditions such as the size of the printed circuit board, the solder paste type, and solder thickness. 0.1mm 2 times 3.Operating Environment and Storage Conditions (1) Operating environment This product was designed under the assumption that it would be used in a normal operating environment. Use of this connector under adverse environmental conditions may lead to discoloration or other kinds of degradation. Use of the connector in regions having exposure to excessive amounts of fine particles and dust, high densities of sulfur dioxide, hydrogen sulfide, nitrogen dioxide or other corrosive gasses (e.g., exhaust gas from automobiles or factories), is not advised environments having a large difference in temperature, such as a place near a heater. (2) Storage conditions Store the product in Hirose Electric s packaging or similar packaging conditions. Temperature: -10 to +40, humidity : 85% or less (recommended storage conditions) Use the product within six months from delivery. Products for which the storage period has expired must be tested for solderability before the use. 6