Model Name : Features : ㅡ Flickerless ㅡ Fullprotection provided: OCP/OVP/OTP/SCP/OLP ㅡ Low Power Dissipation (Standby mode : <0.5Wh ) ㅡ Wide Vout : 55 ~ 94Vdc ㅡ UL8750 / UL1310 ㅡ Compliant with CB, CE, UL safety requirements for LED lighting ㅡ Constant Current Type ㅡ IP67 E480967
Electrical specification No. 1 8 Electrical Efficiency 87 89 % 2) 9 Turnon Delay 0.5 11 13 14 16 17 STBY Power Dissipation 0.5 18 Nominal Input Voltage 120 Nominal Input Frequency 47 50/60 Total Harmonic Distortion (THD) 20 LED Output Current 665 700 735 ma LED Output Current Ripple 70 LED Output Voltage 55 94 12V Output Voltage 10.8 700 15 12V Output Voltage Ripple ± 1.2 Input to Output Min Typ Max Unit Remark 500 220 277 12 13.2 8 Vac 2 Variable Input Voltage 108 300 Vac 3 Maximum Input Current 0.8 Arms 4 5 6 10 63 Hz 7 Inrush Current 65 A 12 19 20 21 22 28 Line to Line 6 Surge 29 Line to Ground 8 s ma Wh Output Open LED Protection 150 Vdc Dielectric Withstand Voltage Power Factor (PF) 90 % Adjustable of LED Current 12V Output Current Storage Temperature 40 25 80 Operating Temperature 40 Case Temperature (Tc) 100 3.75 % 25 50 23 Humidity 20 85 % 50 85 24 Insulation Resistance 10 MΩ 25 26 27 30 31 Item Output Short Circuit Protection ESD Input to Case Output to Case Contact Discharge Air Discharge 3.75 0.5 4 Vdc ma 1) 1) @Cold Start, 3) @94Vdc Load 2) 20 MHz Bandwidth, 2) Rset Vdc 2) Vdc ma 20 MHz Bandwidth, 2) LED Off_Remote Low @Vpeak No Damage Ta = 53 500Vdc between Input & Output Apply for 1 minute 6) 4) 4) 5) 5)
Application Notes 1) Test Condition:120/277Vac 50/60Hz Input,Typical LED Load,Ambient Temperature 25, Measure at the cableend 2) Test Condition: 220Vac 60Hz Input, LED Max. Load, 30min Aging, Ambient Temperature 25 3) The interval of turn on/off should be over 1sec. 4) Surge Specification above is higher than IEC/EN 6100045 Level 4 (Differential 2, Common 4 ) 5) The metal case of the LED driver must be connected with F.G 6) ESD Specification above meets IEC/EN 6100042 Requirements (Contact Level 2, Air Level 3) 7) The metal case of the driver should be grounded. 8) Determined by Paragraph 34.1.2, UL1310 or Paragraph 8.4.2, UL8750, EN613471, EN61347213 Safety Standards Including safety requirements above, the LED driver complies with the following safety standards: No. Item Description 1 UL8750, UL1310 UL Safety Standards 2 IEC/EN 55015 Conducted and Radiated Emission Test 3 IEC/EN 6100032 Harmonic current emissions: Class C 4 IEC/EN 6100033 Voltage Fluctuations and Flicker 5 IEC/EN 6100042 Electrostatic Discharge (ESD): Contact Level 2, Air Level 3 6 IEC/EN 6100043 Radiofrequency Electromagnetic Fields 7 8 IEC/EN 6100044 IEC/EN 6100045 Electrical Fast Transients (EFT) Surges: Level 4 9 IEC/EN 6100046 Injected Currents 10 IEC/EN 6100048 Power Frequency Magnetic Fields 11 IEC/EN 61000411 Voltage Dips and Short Interruptions
Operating window Preliminary *Currently Measurement Data Life Time vs Tcase 120000 100000 Life Time [hrs] 80000 60000 40000 20000 120Vac_30S(94V) 220Vac_30S(94V) 0 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 Tc [ ] Remark) LED Driver has a rated lifetime of 50,000 hours @ Tc 70
*Currently Measurement Data Power Factor(%) 100.00% 20LED500mA 90.00% Power Factor 80.00% 20LED700mA 70.00% 30LED500mA 60.00% 30LED700mA 50.00% 120 220 277 Input Voltage (Vac) THD(%) THD 35.00% 30.00% 25.00% 20.00% 15.00% 10.00% 5.00% 0.00% 120 220 277 Input Voltage (Vac) 20LED500mA 20LED700mA 30LED500mA 30LED700mA Efficiency(%) Eff 100.00% 90.00% 80.00% 70.00% 60.00% 50.00% 120 220 277 Input Voltage (Vac) 20LED500mA 20LED700mA 30LED500mA 30LED700mA
Output Current( ma ) Preliminary *Currently Measurement Data Current 1200.00 1000.00 800.00 600.00 400.00 200.00 0.00 120 220 277 Input Voltage (Vac) 20LED500mA 20LED700mA 30LED500mA 30LED700mA Dimming curve Current 1200.00 1000.00 800.00 600.00 400.00 200.00 0.00 10 9.3 9 8 7 6 5 4 3 2 1 0 Input Voltage (Vac) 20LED500mA 20LED700mA 30LED500mA 30LED700mA Adjustable Of Current( Rset ) 750 LED Current[mA] 700 650 600 550 500 1,000 10,000 100,000 1,000,000 Rset [Ω] Rset
Mechanical Specification TOP BOTTOM Enclosure Size Unit Width Length Height Mount Length Overall Length mm 53.6 177.6 33.9 185.4 192.6 inch 2.11 6.99 1.33 7.30 7.58 Case Material : Aluminium
Wiring Diagram LIVE : Black Neutral : White Caution L N 1) Before installing LED driver, AC power should be turned off. After installing LED driver, AC power should be turned on. 2) When this LED driver are installed as an independent lamp controlgear, endcustomer should protect connecting leads of pri/sec. cable with a certified element. 3) Waterproof connector or Junction box can be assembled with output cables for operating in dry/wet/damp or outdoor environment. LED Control gear 4) Wires should be less than 1m when installed in final equipment L L E S D R V G G LED + : Red LED : Blue Vsen : White Rset : Orange DIM : Violet RMT : Green 12V : Yellow GND : Black GND : Blue 2nd Signal Description Name Feature Purpose Vsen check LED Out Voltage Monotoring LED Open/Short (for Connectivity Module) Rset Adjustable of current Control LED Output Current DIM Dimming Control Brightness RMT LED On/Off Stand by Mode 12V Control Source Supply Controller Power GND 2nd GND Signal GND GND 2nd GND Signal GND Rating Label Drawing
Barcode Label Box Label Material Code ITEM LOT No Quantity [PCS] EXP. Date REV. A** ********* MAKER 24 SOLUM 20**.**.** ~ 20**.**.** USER Model Code SOLUM Model Code SOLUM LOT NO & Quantity of Products Product Date ~ After 5 years ************* **** ********* USER Barcode
Packing Drawing 1. Out Box Dimmension Weight Quantity 540(L) 355(W) 170(H) [mm] < 14Kg 24EA / 1Box TRY BODY NIL PAD OUT BOX 2. Pallet