PANEL ANTENNAS WITH ONLY HIGH BAND ARRAYS 54 April 2015
Ultra-wideband antennas designed to handle 2G, 3G networks and MIMO configurations for LTE on 1.8 / 2.1 / 2.6 networks. HighBand April 2015 55
(2x) 1695-2180 / 2490-2690 MHz 6177600 6177600A 6177600G 6177600DG Twin Dual Band Panel Antenna (2x) XX-Pol 65 / 65 17.0 / 17.5 dbi Variable Tilt Twin dual band antenna, dual polarisation, 8 connectors Independent tilt on each band 0-12 / 0-12 Ultra compact Quadband system for MIMO applications MET and RET versions, AISG1.1 or 3GPP/AISG2.0 Fully internal RET control based on our patented technologies (field replaceable) Ordering Options Model Number Manual Electrical Tilt 6177600 Remote Electrical Tilt AISG1.1 6177600A Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator 6177600G Remote Electrical Tilt 3GPP/AISG2.0 with an MDDU RET Actuator 6177600DG Access Ports Description (Connectors) This antenna is built with two identical Dual Band Antennas, housed side-by-side in the same shroud. The antenna has 8 colour-coded connectors located at the bottom face. See image on the following page. B1 B2 Wide Band 1695-2180 MHz Ports (2x) 4.3-10 Female Long Neck Y1 Y2 LTE 2600 2490-2690 MHz Ports (2x) 4.3-10 Female Long Neck Electrical Characteristics B1-B2 Y1-Y2 Frequency Bands (MHz) 1800 2100 2600 Gain (dbi) Tilt 0 Tilt Mid Value Tilt Max Value 16.8 16.8 16.8 Input Impedance 50Ω 50Ω VSWR < 1.5 < 1.5 Polarisation ±45 ±45 Horizontal Beamwidth (-3 db) 65 63 61 Vertical Beamwidth (-3 db) 7.0 6.4 5.2 Electrical Downtilt Range 0-12 0-12 Inter/Intra Band Isolation, > 28 db from 0 to 2 tilt, > 28 db from 0 to 2 tilt Upper Sidelobe Rejection (20 sector above main beam) Front-to-Back Ratio @ 180 @ 180 ±30 17.1 17.1 17.0 17.5 17.5 17.2 18 db Typical 18 db Typical > 25 db > 25 db Maximum Power (Per Port) 200 W 200 W Intermodulation 3rd Order for 2x20W Carriers < -110 dbm < -110 dbm Electrical Downtilt Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s). Manual Electrical Tilt (MET) Remote Electrical Tilt (RET) A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counterclockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna. The remote control of the electrical tilt is managed by a Multi-Device Unit (MDCU) or a Multi-Device Dual Unit (MDDU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each band (no need for daisy chain cables between the bands). This module does not add any additional length to the antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain visible and the antenna still has manual tilt control (manual override). RET-Ready antennas are delivered with the RET Actuator (MDCU or MDDU) already installed and pre-commissioned with all antenna parameters. Every RET device is factory configured and calibrated so the antenna is ready to be used once delivered to the site which means that there is no need for further installation of RET devices or for programming their configuration or for running a calibration process. RET-Ready Actuator (one per antenna) Multi-Device Unit (MCDU) Multi-Device Dual Unit (MDDU) The MDCU is an electronic module that allows the remote control of the electrical downtilt (RET) in Amphenol antennas with factory embedded motors. Refer to ordering options. The MDDU allows two separate RET lers to independently drive the RETs in antennas with factory embedded motors (for antenna sharing or two technologies). Refer to ordering options. Environmental Operating Temperature Range -40 C to +60 C Environmental ETS 300 019 RoHS Compliant Yes 56 April 2015
(2x) 1695-2180 / 2490-2690 MHz 6177600 6177600A 6177600G 6177600DG Twin Dual Band Panel Antenna (2x) XX-Pol 65 / 65 17.0 / 17.5 dbi Variable Tilt Mechanical Characteristics Dimensions (Height x Width x Depth) 1390 x 265 x 114 mm Weight (Excluding Mounting Accessories) 17 kg Shroud Outdoor Fibreglass, Grey RAL7035 Wind Speed Operational: 160 km/hr Survival: 200 km/h Wind Load at 150 km/h Frontal: 420 N Lateral: 270 N Rear: 455 N Mounting Kit Options Part Number Weight All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below. Packaging Carton Box 1.61 x 0.365 x 0.23 m 0.135 m 3 27 kg Includes 0900181/00 Kit Brackets for pole 48 to 115 mm 0900181/00 3.4 kg Brackets for pole 70 to 150 mm 0900182/00 3.9 kg Kit to add mechanical tilt to above brackets 0900396/00 2.3 kg Bottom View of Antenna Tilt indicators covered by transparent caps. Manual adjustment is accessed by removing the caps. Knob colours are the same as the connectors. Location of the MDCU or MDDU for RET Installation In order to operate RET control, the transparent caps covering the tilt adjustment indicators must be engaged and locked. Do not cut them from the antenna. Always attach the antenna by the two mounting points. Do no install the antenna with the connectors facing upward. Dimensions (in mm) April 2015 57
(2x) 6177100 6177100A 6177100G Twin Single Band Panel Antenna (2x) X-Pol 65 18.0 dbi Variable Tilt Twin single band antenna, dual polarisation, 4 connectors Wide range of electrical tilt, variable 0-12 on each antenna MET and RET versions, AISG1.1 or 3GPP/AISG2.0 Fully internal RET control based on our patented technologies Ordering Options Model Number Manual Electrical Tilt 6177100 Remote Electrical Tilt AISG1.1 Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator 6177100A 6177100G Access Ports Description (Connectors) The antenna has 4 connectors located at the bottom face. See image on the following page. Ultra Wide Band LEFT Ports (2x) 7/16-DIN Female Long Neck Ultra Wide Band RIGHT Ports (2x) 7/16-DIN Female Long Neck Electrical Characteristics (General) The antenna contains two radiating arrays housed in a single mechanical structure. Isolation Between Arrays Electrical Characteristics Frequency Bands Gain Input Impedance 1710...1880...2170...2690 MHz 16.9...17.2...17.6...18.0 dbi 50Ω VSWR < 1.5 Polarisation ±45 Horizontal Beamwidth (-3 db) 65 Vertical Beamwidth (-3 db) 6 Electrical Downtilt Range 0-12 Isolation Between Ports Upper Sidelobe Rejection (20 sector above main beam) Null Fill (First Null Below Main Beam) Front-to-Back Ratio Maximum Power (Per Port) Intermodulation 3rd Order for 2x20W Carriers > 18 db < 18 db Typical 160 W < -153 dbc Electrical Downtilt Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s). Manual Electrical Tilt (MET) Remote Electrical Tilt (RET) RET Module Part Number (one per antenna) A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counterclockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna. The remote control of the electrical tilt is managed by a Multi-Device Unit (MDCU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each band (no need for daisy chain cables between the bands). This module does not add any additional length to the antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain visible and the antenna still has manual tilt control (manual override). MDCU-A0000 for AISG1.1 protocol (one unit included in 6177100A) MDCU-G0000 for 3GPP/AISG2.0 protocol (one unit included in 6177100G) Environmental Operating Temperature Range -40 C to +60 C Environmental ETS 300 019 RoHS Compliant Yes 58 April 2015
(2x) 6177100 6177100A 6177100G Twin Single Band Panel Antenna (2x) X-Pol 65 18.0 dbi Variable Tilt Mechanical Characteristics Dimensions (Height x Width x Depth) 1394 x 265 x 114 mm Weight (Excluding Mounting Accessories) 13 kg Shroud Outdoor Plastic, Grey RAL7035 Wind Speed Operational: 160 km/hr Survival: 200 km/h Wind Load (EN1991-4-1) at 150 km/h Frontal: 420 N Lateral: 270 N Rear: 455 N at 160 km/h Frontal: 478 N Lateral: 307 N Rear: 518 N Mounting Kit Options Part Number Weight All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below. Packaging Carton Box 1.61 x 0.365 x 0.23 m 0.135 m 3 23 kg Includes 0900181/00 Kit Brackets for pole 48 to 115 mm 0900181/00 3.4 kg Brackets for pole 70 to 150 mm 0900182/00 3.9 kg Kit to add mechanical tilt to above brackets 0900396/00 2.3 kg Wall mounting bracket with azimuth pan 0900183/00 1.6 kg Wall mounting brackets with mechanical tilt and azimuth pan 0900885/00 3.3 kg Bottom View of Antenna Dimensions (in mm) 265 114 Location of the MDCU for RET Tilt indicators covered by transparent caps. Manual adjustment is accessed by removing the caps. Knob colours are the same as the connectors. 1394 1127,5 Y1 Y2 Installation In order to operate RET control, the transparent caps covering the tilt adjustment indicators must be engaged and locked. Do not cut them from the antenna. Always attach the antenna by the two mounting points. Do no install the antenna with the connectors facing upward. April 2015 59
(3x) 6177400 6177400A 6177400G Triple Band Panel Antenna (3x) X-Pol 65 18.0 dbi Variable Tilt Triple Ultra Wideband antenna, dual polarisation, 6 connectors Wide range of electrical tilt, variable 0-12 on each antenna MET and RET versions, AISG1.1 or 3GPP/AISG2.0 Fully internal RET control based on our patented technologies Ordering Options Model Number Manual Electrical Tilt 6177400 Remote Electrical Tilt AISG1.1 Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator 6177400A 6177400G Access Ports Description (Connectors) The antenna has 6 connectors located at the bottom face. See image on the following page. Ultra Wide Band LEFT Ports (2x) 7/16-DIN Female Long Neck Ultra Wide Band CENTER Ports (2x) 7/16-DIN Female Long Neck Ultra Wide Band RIGHT Ports (2x) 7/16-DIN Female Long Neck Electrical Characteristics (General) The antenna contains three radiating arrays housed in a single mechanical structure. Isolation Between Arrays Electrical Characteristics Frequency Bands Gain Input Impedance 1710...1880...2170...2690 MHz 16.9...17.2...17.6...18.3 dbi 50Ω VSWR < 1.5 Polarisation ±45 Horizontal Beamwidth (-3 db) 65 Vertical Beamwidth (-3 db) 6 Electrical Downtilt Range 0-12 Isolation Between Ports Upper Sidelobe Rejection (20 sector above main beam) Null Fill (First Null Below Main Beam) Front-to-Back Ratio Maximum Power (Per Port) Intermodulation 3rd Order for 2x20W Carriers > 28 db > 18 db < 18 db Typical 160 W < -153 dbc Electrical Downtilt Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s). Manual Electrical Tilt (MET) Remote Electrical Tilt (RET) RET Module Part Number (one per antenna) A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counterclockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna. The remote control of the electrical tilt is managed by a Multi-Device Unit (MDCU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each band (no need for daisy chain cables between the bands). This module does not add any additional length to the antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain visible and the antenna still has manual tilt control (manual override). MDCU-A0000 for AISG1.1 protocol (one unit included in 6177400A) MDCU-G0000 for 3GPP/AISG2.0 protocol (one unit included in 6177400G) Environmental Operating Temperature Range -40 C to +60 C Environmental ETS 300 019 RoHS Compliant Yes 60 April 2015
(3x) 6177400 6177400A 6177400G Triple Band Panel Antenna (3x) X-Pol 65 18.0 dbi Variable Tilt Mechanical Characteristics Dimensions (Height x Width x Depth) 1394 x 392 x 114 Weight (Excluding Mounting Accessories) 22.5 kg Shroud Outdoor Plastic, Grey RAL7035 Wind Speed Operational: 160 km/hr Survival: 200 km/h Wind Load (EN1991-4-1) at 150 km/h Frontal: 625 N Lateral: 250 N Rear: 678 N at 160 km/h Frontal: 712 N Lateral: 285 N Rear: 771 N Mounting Kit Options Part Number Weight All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below. Packaging Carton Box 1.61 x 0.35 x 0.25 m 0.13 m 3 28 kg Brackets for pole 48 to 115 mm 0900181/00 3.4 kg Brackets for pole 70 to 150 mm 0900182/00 3.9 kg Kit to add mechanical tilt to above brackets 0900396/00 2.3 kg Wall mounting bracket with azimuth pan 0900183/00 1.6 kg Wall mounting brackets with mechanical tilt and azimuth pan 0900885/00 3.3 kg Bottom View of Antenna Dimensions (in mm) Location of the MDCU for RET 392 114 Tilt indicators covered by transparent caps. Manual adjustment is accessed by removing the caps. Knob colours are the same as the connectors. 1394 1127,5 Y1 Y2 Y3 Installation In order to operate RET control, the transparent caps covering the tilt adjustment indicators must be engaged and locked. Do not cut them from the antenna. Always attach the antenna by the two mounting points. Do no install the antenna with the connectors facing upward. April 2015 61
6176100 6176100A 6176100G Single Band Panel Antenna X-Pol 65 18.3 dbi Variable Tilt Ultra wide band antenna, dual polarisation, 2 connectors Wide range of electrical tilt, variable 0-12 MET and RET versions, AISG1.1 or 3GPP/AISG2.0 RET module fully inserted inside the antenna (field replaceable) Ordering Options Model Number Manual Electrical Tilt 6176100 Remote Electrical Tilt AISG1.1 Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator 6176100A 6176100G Access Ports Description (Connectors) The antenna has 2 colour-coded connectors located at the bottom face. See image on the following page. YELLOW Rings Ultra Wide Band Ports (2x) 7/16-DIN Female Long Neck Electrical Characteristics Frequency Bands Gain Input Impedance 1710...1880...2170...2690 MHz 16.9...17.2...17.6...18.3 dbi 50Ω VSWR < 1.5 Polarisation ±45 Horizontal Beamwidth (-3 db) 65 Vertical Beamwidth (-3 db) 6 Electrical Downtilt Range 0-12 Isolation Between Ports Upper Sidelobe Rejection (20 sector above main beam) Null Fill (First Null Below Main Beam) Front-to-Back Ratio Maximum Power (Per Port) Intermodulation 3rd Order for 2x20W Carriers > 18 db < 18 db Typical 160 W < -153 dbc Electrical Downtilt The tilt indicator is covered by a removable transparent cap. Manual Electrical Tilt (MET) Remote Electrical Tilt (RET) RET Module Part Number (one per antenna) A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour is identical to the connector colour as defined above. To access the knob, remove the cap by turning it counterclockwise. It is re-installed by opposite rotation. Do not remove the transparent cap from the antenna. The remote control of the electrical tilt is managed by a Multi-Device Unit (MDCU) inserted in the bottom of the antenna. This module does not add any additional length to the antenna. For RET control, the transparent cap must be in place and locked. The tilt angle indicator always remains visible and the antenna still has manual tilt control (manual override). MDCU-A0000 for AISG1.1 protocol (one unit included in 6176100A) MDCU-G0000 for 3GPP/AISG2.0 protocol (one unit included in 6176100G) Environmental Operating Temperature Range -40 C to +60 C Environmental ETS 300 019 RoHS Compliant Yes 62 April 2015
6176100 6176100A 6176100G Single Band Panel Antenna X-Pol 65 18.3 dbi Variable Tilt Mechanical Characteristics Dimensions (Height x Width x Depth) Weight (Excluding Mounting Accessories) Shroud 1390 x 170 x 100 mm 7 kg Outdoor Plastic, Grey RAL7035 Wind Speed Operational: 160 km/hr Survival: 200 km/h Wind Load at 160 km/h Frontal: 288 N Side: 167 N Mounting Kit Options Part Number Weight All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below. Brackets for pole 48 to 115 mm 0900181/00 3.4 kg Kit to add mechanical tilt to above brackets 0900188/00 1.5 kg Bottom View of Antenna Dimensions (in mm) Location of the MDCU for RET 100 170 Tilt indicator covered by transparent caps. Manual adjustment is accessed by removing the caps. Knob colours are the same as the connectors. 1390 YELLOW Installation In order to operate RET control, the transparent caps covering the tilt adjustment indicators must be engaged and locked. Do not cut them from the antenna. 77 Always attach the antenna by the two mounting points. Do no install the antenna with the connectors facing upward. April 2015 63