Technical Information Dosimag

TI00066D/06/EN/.5 7960 Products Solutions Services Technical Information Dosimag Electromagnetic flowmeter Flowmeter with maximum repeatability and ultra-compact sensor with hygienic design Application The measuring principle is practically independent of pressure, density, temperature and viscosity For demanding batching and dosing applications Device properties Wetted materials suitable for CIP/SIP cleaning Nominal diameter: DN to 5 (¹ ₈ to ") FDA-compliant measuring device Pulse/frequency/switch output, Modbus RS85 ATEX, ccsaus Excellent and easy-to-clean transmitter Your benefits High process safety high measuring accuracy and repeatability in shortest filling time Energy-saving flow measurement no pressure loss due to cross-section constriction Maintenance-free no moving parts Versatile and time saving wiring plug connector Industry optimized ultra compact design For hygiene requirements stainless steel housing

Table of contents Document information... 3 Symbols used... 3 Function and system design... 3 Measuring principle... 3 Measuring system... Equipment architecture... Safety... 6 Input... 6 Measured variable... 6 Measuring range... 6 Operable flow range... 7 Input signal... 7 Output... 7 Output signal... 7 Signal on alarm... 9 ow flow cut off... 9 Galvanic isolation... 9 Protocol-specific data... 9 Power supply... 0 Terminal assignment... 0 Pin assignment, device plug... Supply voltage... Power consumption... Current consumption... 5 Power supply failure... 5 Electrical connection... 5 Potential equalization... 5 Cable specification... 6 Performance characteristics... 6 Reference operating conditions... 6 Maximum measured error... 6 Repeatability... 7 Influence of ambient temperature... 7 Installation... 7 Mounting location... 7 Orientation... 8 Inlet and outlet runs... 9 Adapters... 0 Special mounting instructions... 0 Process... Medium temperature range... Conductivity... 3 Pressure-temperature ratings... 3 Pressure tightness... 3 Flow limit... Pressure loss... System pressure... Vibrations... Mechanical construction... 5 Dimensions in SI units... 5 Dimensions in US units... 3 Weight... 37 Materials... 37 Fitted electrodes... 38 Process connections... 38 Surface roughness... 38 Operability... 38 ocal operation... 38 Remote operation... 38 Certificates and approvals... 39 CE mark... 39 C-Tick symbol... 39 Ex approval... 39 Sanitary compatibility... 39 Pressure Equipment Directive... 0 Measuring instrument approval... 0 Other standards and guidelines... 0 Ordering information... 0 Accessories... 0 Device-specific accessories... Communication-specific accessories... Service-specific accessories... Supplementary documentation... Standard documentation... Supplementary device-dependent documentation... Registered trademarks... 3 Environment... Ambient temperature range... Storage temperature... Degree of protection... Shock resistance... Vibration resistance... Interior cleaning... Electromagnetic compatibility (EMC)... Endress+Hauser

Document information Symbols used Electrical symbols Symbol Meaning Symbol Meaning Direct current Direct current and alternating current Protective ground connection A terminal which must be connected to ground prior to establishing any other connections. Alternating current Ground connection A grounded terminal which, as far as the operator is concerned, is grounded via a grounding system. Equipotential connection A connection that has to be connected to the plant grounding system: This may be a potential equalization line or a star grounding system depending on national or company codes of practice. Symbols for certain types of information Symbol Meaning Permitted Procedures, processes or actions that are permitted. Preferred Procedures, processes or actions that are preferred. Forbidden Procedures, processes or actions that are forbidden. Tip Indicates additional information. Reference to documentation Reference to page Reference to graphic Visual inspection Symbols in graphics Symbol Meaning Symbol Meaning,, 3,... Item numbers,, Series of steps A, B, C,... Views A-A, B-B, C-C,... Sections - Hazardous area Flow direction. Safe area (non-hazardous area) Function and system design Measuring principle Following Faraday's law of magnetic induction, a voltage is induced in a conductor moving through a magnetic field. Endress+Hauser 3

U e I v B I A007035 Ue B I v Induced voltage Magnetic induction (magnetic field) Electrode spacing Current Flow velocity In the electromagnetic measuring principle, the flowing medium is the moving conductor. The voltage induced (U e ) is proportional to the flow velocity (v) and is supplied to the amplifier by means of two measuring electrodes. The flow volume (Q) is calculated via the pipe cross-section (A). The DC magnetic field is created through a switched direct current of alternating polarity. Formulae for calculation Induced voltage U e = B v Volume flow Q = A v Measuring system The device consists of a transmitter and a sensor. The device is available as a compact version: The transmitter and sensor form a mechanical unit. Dosimag Transmitter Materials: Transmitter housing: stainless steel.308 (30) Housing seal: EPDM Configuration: Via operating tools (e.g. FieldCare) Sensor Range of nominal diameter: DN (⁵ ₃₂"), DN 8 (³ ₈"), 5 (½"), 5 (") Materials: Sensor housing: stainless steel.308 (30) Measuring tube: stainless steel.30 (30) iner: PFA Process connection seals: EPDM, silicone, Viton Electrodes:.35 (36); option Alloy C,.60 (UNS N060), tantalum, platinum A00338 Equipment architecture Device version: Two pulse/frequency/switch outputs The device version has two pulse/frequency/switch outputs 0. Endress+Hauser

3 Options for integration into a system for batching processes Pulse/frequency/current output Pulse/frequency/current output 3 Automation system (e.g. PC) Control of valve (by automation system) A007057 Device version: Modbus RS85, one or two switch outputs (Batch) and one status input Device versions with MODBUS RS85 have one or two switch outputs for valve control for the regulation of batching processes 0. 3 5 Options for integration into a system for batching processes MODBUS RS85: Measured value (to the automation system) Status input: Control of batching process (by the automation system) 3 Automation system (e.g. PC) Switch output (batch): valve control, level 5 Switch output (batch): valve control, level A0066 Integrated batching functions The following parameters can be used to configure and monitor batching processes. Configuration Measured variable: volume flow Unit Batch quantity Fixed compensation quantity Select batch profile Drip correction mode: Off, low flow cut off or fixed time Endress+Hauser 5

Measuring time drip quantity Filter depth drip median (3, 5 or 7) Average drip correction quantity Batch levels: One-level, two-level or one-level and blow out Start and stop level Blow out delay and duration Maximum batch time Maximum flow Disable time pressure shock suppression Display Total amount measured from last batching process (incl. drip quantity) Duration of last batching process (incl. measurement of drip quantity) Switch-off time: From time of switch-off to when measurement of the drip quantity is complete Current drip correction quantity (drip correction quantity for next batching process) Sum of all batching processes measured Number of batching processes. The batching process (start batch, stop batch etc.) is controlled by the automation system via the status input or the Modbus RS85. Safety IT security We only provide a warranty if the device is installed and used as described in the Operating Instructions. The device is equipped with security mechanisms to protect it against any inadvertent changes to the device settings. IT security measures in line with operators' security standards and designed to provide additional protection for the device and device data transfer must be implemented by the operators themselves. Input Measured variable Measuring range Direct measured variables Volume flow (proportional to induced voltage) Typically v = 0.0 to 0 m/s (0.03 to 33 ft/s) with specified accuracy Flow characteristic values in SI units Nominal diameter Recommended flow Factory settings Max. full scale value Pulse value ow flow cut off (v ~ 0.0 m/s) [mm] [l/s] [ml] [ml/s] 0. 0.005 0.5 8 0.5 0.0 5K ). 0. 7 5.66 0. 7 5 5 0. 6 ) Conical version (corresponds to DN ) 6 Endress+Hauser

Flow characteristic values in US units Nominal diameter Recommended flow Factory settings Max. full scale value Pulse value ow flow cut off (v ~ 0.3 ft/s) [in] [gal/s] [oz fl] [oz fl/s] ⁵ ₃₂ 0.035 0.000 0.0 ⁵ ₁₆ 0.3 0.00 0.08 ½K ) 0.3 0.00 0.5 ½ 0. 0.00 0.5.33 0.007 0.53 ) Conical version (corresponds to DN ) To calculate the measuring range, use the Applicator sizing tool Operable flow range Over 000 : Recommended measuring range "Flow limit" section Input signal Available only for device versions using the Modbus RS85 communication method 0. Status input The batching process is controlled by the automation system via the device's status input. Maximum input values Response time Input signal level Assignable functions DC 30 V 6 ma Adjustable: 0 to 00 ms ow level: 0 to.5 V High level: 3 to 30 V Off Start batching process Start and stop batching process Reset totalizers -3 separately Reset all totalizers Flow override Output Output signal Pulse/frequency/switch output Function Can be set to: Pulse Quantity-proportional pulse with pulse width to be configured. Automatic pulse Quantity-proportional pulse with on/off ratio of : Frequency Flow-proportional frequency output with on/off ratio of : Switch Contact for displaying a status Channel Redundant output of pulse output: 0, 90 or 80 Endress+Hauser 7

Version Maximum input values Voltage drop Passive, open emitter DC 30 V 5 ma At 5 ma: DC V Pulse output Pulse width Maximum pulse rate Pulse value Assignable measured variables Adjustable: 0.05 to 3.75 ms 0 000 Impulse/s Adjustable Volume flow Frequency output Output frequency Damping Adjustable: 0 to 0 000 Hz Adjustable: 0 to 999.9 s Pulse/pause ratio : Assignable measured variables Volume flow Switch output Switching behavior Number of switching cycles Assignable functions Binary, conductive or non-conductive Unlimited Off On Diagnostic behavior Alarm Alarm and warning Warning imit value: Off Volume flow Flow velocity Status ow flow cut off Modbus RS85 Physical interface In accordance with EIA/TIA-85-A standard Switch output (batch: valve control) Only available for device version with Modbus RS85 0. Depending on the device version, the device has one or two switch outputs. Switch output Version Maximum input values Switching behavior Number of switching cycles Assignable functions Active, open emitter DC 30 V 500 ma Binary, conductive or non-conductive Unlimited Open Closed Batching 8 Endress+Hauser

Signal on alarm Depending on the interface, failure information is displayed as follows: Pulse/frequency/switch output Pulse output Failure mode Choose from: Actual value No pulses Frequency output Failure mode Choose from: Actual value 0 Hz Defined value: 0 to 0 000 Hz Switch output Failure mode Choose from: Current status Open Closed Modbus RS85 Failure mode Choose from: NaN value instead of current value ast valid value ow flow cut off Galvanic isolation Protocol-specific data The switch points for low flow cut off are user-selectable. Device version: pulse/frequency/switch outputs Order code for "Output, input", option 3: Pulse/frequency/switch outputs galvanically isolated from supply potential. Pulse/frequency/switch outputs not galvanically isolated from each other. Device version: Modbus RS85, switch output (batch), status input (Order code for "Output, input": option ) Switch outputs (batch) and status input on supply potential Device version: Modbus RS85, switch outputs (batch), status input (Order code for "Output, input", option 5:) Switch outputs (batch) on supply potential. Status input, galvanically isolated. Modbus RS85 Protocol Modbus Applications Protocol Specification V. Device type Slave Slave address range to 7 Broadcast address range 0 Function codes 03: Read holding register 0: Read input register 06: Write single registers 08: Diagnostics 6: Write multiple registers 3: Read/write multiple registers 3: Read device identification Endress+Hauser 9

Broadcast messages Supported baud rate Data transfer mode Data access Supported by the following function codes: 06: Write single registers 6: Write multiple registers 3: Read/write multiple registers 00 BAUD 00 BAUD 800 BAUD 9 600 BAUD 9 00 BAUD 38 00 BAUD 57 600 BAUD 5 00 BAUD ASCII RTU Each device parameter can be accessed via Modbus RS85. For Modbus register information Power supply Terminal assignment Connection is solely by means of device plug: There are different device versions available: Order code for "Output, input": Device plug Option 3: pulse/frequency/switch outputs ) Option : Modbus RS85, switch output (batch), status input Option 5: Modbus RS85, switch outputs (batch), status input 3 Option 6: Modbus RS85 (custody transfer mode) ) Can also be used for custody transfer mode. 0 Endress+Hauser

Pin assignment, device plug Device version: pulse/frequency/switch outputs Order code for "Output, input", option 3: Pulse/frequency/switch output RSE 8 Mx A B 8 3 3 8 7 6 5 5 7 6 A B 3 5 E + - 6 7 8 3 Connection to device A Coupling: Supply voltage, pulse/freq./switch output B Connector: Supply voltage, pulse/freq./switch output E PEV or SEV power supply to Pin assignment 8 A00598 Pin assignment Connection: Coupling (A) Connector (B) Pin Assignment + Supply voltage + Service interface RX 3 + Service interface TX - Supply voltage 5 + Pulse/frequency/switch output 6 Pulse/frequency/switch output 7 Pulse/frequency/switch output 8 Service interface GND Observe cable specifications 6. Endress+Hauser

Device version: Modbus RS85, status output and status input Order code for "Output, input", option : Modbus RS85 switch output (batch) status input RSE 8 Mx RSE 5 Mx A B C D 8 3 3 8 3 3 7 6 5 5 7 6 5 5 A B C D E + - 3 3 5 6 7 8 5 V Connection to device A Coupling: Supply voltage, Modbus RS85 B Connector: Supply voltage, Modbus RS85 C Coupling: Switch output (batch), status input D Connector: Switch output (batch), status input E PEV or SEV power supply V Valve (batch) to Pin assignment 8 A005977 Pin assignment Connection: Coupling (A) Connector (B) Connection: Coupling (C) Connector (D) Pin Assignment Pin Assignment + Supply voltage + Status input + Service interface RX Status input 3 + Service interface TX 3 Switch output (batch) - Supply voltage + Switch output (batch) 5 Not assigned 5 Not assigned 6 A Modbus RS85 7 B Modbus RS85 8 Service interface GND Observe cable specifications 6. Endress+Hauser

Device version: Modbus RS85, status outputs and status input Order code for "Output, input", option 5: Modbus RS85 switch outputs (batch) status input RSE 8 Mx RSE 5 Mx A B C D 8 3 3 8 3 3 7 6 5 5 7 6 5 5 E + - A 3 B C 3 D V 5 6 7 8 5 V 5 Connection to device A Coupling: Supply voltage, Modbus RS85 B Connector: Supply voltage, Modbus RS85 C Coupling: Switch outputs (batch), status input D Connector: Switch outputs (batch), status input E PEV or SEV power supply V Valve (batch), level V Valve (batch), level to Pin assignment 8 A005963 Pin assignment Connection: Coupling (A) Connector (B) Connection: Coupling (C) Connector (D) Pin Assignment Pin Assignment + Supply voltage + Status input + Service interface RX + Switch output (batch) 3 + Service interface TX 3 Switch outputs, status input - Supply voltage + Switch output (batch) 5 Not assigned 5 Not assigned 6 A Modbus RS85 7 B Modbus RS85 8 Service interface GND Observe cable specifications 6. Endress+Hauser 3

Device version: Modbus RS85 (custody transfer mode) Order code for "Output, input", option 6 (device version for custody transfer mode): Modbus RS85 RSE 8 Mx A B C D 8 3 3 8 7 6 5 5 7 6 A B C D E + - 3 5 6 7 8 6 Connection to device A Coupling: Supply voltage, Modbus RS85 B Connector: Supply voltage, Modbus RS85 C Coupling at device D Connector: Dongle (hardware write protection for custody transfer mode) E PEV or SEV power supply A007089 Pin assignment Connection: Coupling (A) Connector (B) Connection: Coupling (C) Connector (D) Pin Assignment Pin Assignment + Supply voltage + Service interface RX 3 + Service interface TX 3 - Supply voltage Dongle (hardware write protection for custody transfer mode) 5 Not assigned 5 6 A Modbus RS85 7 B Modbus RS85 8 Service interface GND Note cable specification 6. Supply voltage DC V (nominal voltage: DC 0 to 30 V) The power unit must be tested to ensure that it meets safety requirements (e.g. PEV, SEV). The supply voltage must not exceed a maximum short-circuit current of 50 A. Power consumption.5 W Endress+Hauser

Current consumption Order code for "Output, input": Maximum Power consumption Option 3: pulse/frequency/switch outputs 5 ma Option : Modbus RS85, switch output (batch), status input 5 ma + 500 ma ) Option 5: Modbus RS85, switch outputs (batch), status input 5 ma + 000 ma ) Option 6: Modbus RS85 (custody transfer mode) 5 ma ) Additional 500 ma per switch output (batch) used. Switch-on current: max. A (< 8 ms) Power supply failure Electrical connection Totalizers stop at the last value measured. Error messages (incl. total operated hours) are stored. Connection is solely by means of device plug: A B C D A003687 A, C Coupling B, D Plug There are different device versions available: Order code for "Output, input": Device plug Option 3: pulse/frequency/switch outputs Option : Modbus RS85, switch output (batch), status input Option 5: Modbus RS85, switch outputs (batch), status input 3 Option 6: Modbus RS85 (custody transfer mode) Grounding Grounding is by means of a cable socket. A0003838 Potential equalization Requirements No potential matching is needed for grounded steel lines. For devices intended for use in hazardous locations, please observe the guidelines in the Ex documentation (XA). Endress+Hauser 5

Cable specification Permitted temperature range 0 C ( 0 F) to +80 C (+76 F) Minimum requirement: cable temperature range ambient temperature +0 K Signal cable Cables are not included in the scope of delivery; they can be ordered as an accessory 0. Pulse/frequency/switch output Standard installation cable is sufficient. Status input and switch output (batch) Standard installation cable is sufficient. Modbus RS85 The electrical connection of the shield to the device housing must be properly implemented (e.g. using a knurled nut). Please note the following with regard to cable loading: Voltage drop due to the cable length and cable type. Valve performance. Total length of cable in the Modbus network 50 m Use a shielded cable. Example: Terminated device connector with cable: umberg RKWTH 8-99/0 Total length of cable in the Modbus network > 50 m Use shielded twisted pair cable for RS85 applications. Example: Cable: Belden item no. 98 (for -wire version, the same cable can be used for the power supply) Terminated device plug: umberg RKCS 8/9 (shieldable version) Performance characteristics Reference operating conditions In accordance with DIN EN 90 Medium temperature: +8 ± C (+8 ± F) Ambient temperature: + ± C (+7 ± F) Warm-up period:30 min Installation Inlet run > 0 DN Outlet run > 5 DN Sensor and transmitter grounded. The sensor is centered in the pipe. To calculate the measuring range, use the Applicator sizing tool Maximum measured error Error limits under reference operating conditions o.r. = of reading Volume flow ±0.5 % o.r. ± to m/s (3.3 to 3 ft/s) or ±0.5 % o.r. ± mm/s (0.0 in/s) or ±5 % o.r. Fluctuations in the supply voltage do not have any effect within the specified range. 6 Endress+Hauser

Accuracy of outputs In the case of analog outputs, the output accuracy must also be considered for the measured error, in contrast, this need not be considered in the case of fieldbus outputs (Modbus RS85). The outputs have the following base accuracy specifications. Pulse/frequency output o.r. = of reading Accuracy Max. ±50 ppm o.r. (across the entire ambient temperature range) Repeatability o.r. = of reading DN 5 (500 ml/s), DN 5 (00 ml/s), DN 8 (50 ml/s), DN (0 ml/s); 00 μs/cm Batch time t a [s] Relative standard deviation in relation to the batched volume [%].5 s < t a < 3 s 0. 3 s < t a < 5 s 0. 5 s < t a 0. DN 5K (00 ml/s); 00 μs/cm Batch time t a [s] Relative standard deviation in relation to the batched volume [%].5 s < t a < 3 s 0.5 3 s < t a < 5 s 0. 5 s < t a 0.08 Influence of ambient temperature Pulse/frequency output Temperature coefficient No additional effect. Included in accuracy. Installation No special measures such as supports are necessary. External forces are absorbed by the construction of the device. Mounting location h A00333 Preferably install the sensor in an ascending pipe, and ensure a sufficient distance to the next pipe elbow: h DN To prevent measuring errors arising from accumulation of gas bubbles in the measuring tube, avoid the following mounting locations in the pipe: Highest point of a pipeline. Directly upstream of a free pipe outlet in a down pipe. Endress+Hauser 7

Installation in down pipes Install a siphon with a vent valve downstream of the sensor in down pipes whose length h 5 m (6. ft). This precaution is to avoid low pressure and the consequent risk of damage to the measuring tube. This measure also prevents the system losing prime. For information on the liner's resistance to partial vacuum 3 h 7 Installation in a down pipe Vent valve Pipe siphon h ength of down pipe A00706 Installation in partially filled pipes A partially filled pipe with a gradient necessitates a drain-type configuration. 5 DN DN A007063 Orientation The direction of the arrow on the sensor nameplate helps you to install the sensor according to the flow direction (direction of medium flow through the piping). An optimum orientation can prevent buildup and the accumulation of gas or air in the measuring tube. Valves Never install the sensor downstream from a filling valve. If the sensor is completely empty this corrupts the measured value. Correct measurement is only possible if the pipe is completely full. Perform sample fillings before commencing filling in production. 3 3 A0003768 Measuring device Filling valve 3 Container 8 Endress+Hauser

Filling systems The pipe system must be completely full to ensure optimum measurement. 3 3 3 8 Filling system Measuring device Filling valve 3 Container A0003795 Horizontal A00587 Measuring electrodes The measuring electrode plane must be horizontal. This prevents brief insulation of the two measuring electrodes by entrained air bubbles. High temperatures 9 Recommended orientation in the event of strong heat formation A0003830 To prevent the electronics from overheating in the event of strong heat formation (e.g. CIP or SIP cleaning process), install the measuring device with the transmitter part pointing downwards. Inlet and outlet runs If possible, install the sensor upstream from fittings such as valves, T-pieces or elbows. Observe the following inlet and outlet runs to comply with accuracy specifications: Endress+Hauser 9

5 DN DN A00675 Adapters Suitable adapters to DIN EN 55 (double-flange reducers) can be used to install the sensor in largerdiameter pipes. The resultant increase in the rate of flow improves measuring accuracy with very slow-moving fluids. The nomogram shown here can be used to calculate the pressure loss caused by reducers and expanders: Calculate the ratio of the diameters d/d. From the nomogram read off the pressure loss as a function of flow velocity (downstream from the reduction) and the d/d ratio. The nomogram only applies to liquids with a viscosity similar to that of water. [mbar] 00 8 m/s 7 m/s 0 6 m/s 5 m/s max. 8 m/s d D 3 m/s m/s m/s d / D 0.5 0.6 0.7 0.8 0.9 A006359 Special mounting instructions Information for filling systems Correct measurement is possible only if the piping is completely filled. We therefore recommend that some test batches be carried out prior to production batching. 0 Endress+Hauser

Circular filling system 3 A000376 Measuring device Tank 3 Batching valve Vessel inear filling system 3 A000376 Measuring device Tank 3 Batching valve Vessel Environment Ambient temperature range Transmitter 0 to +60 C ( 0 to +0 F) Sensor 0 to +60 C ( 0 to +0 F) Temperature tables The following interdependencies between the permitted ambient and fluid temperatures apply when operating the device in hazardous areas: Endress+Hauser

Ex na SI units T5 [00 C] T [35 C] T3 [00 C] T [300 C] T [50 C] Ambient temperature T a 60 50 5 5 5 Maximum medium temperature T m 70 05 30 30 30 US units T5 [ F] T [75 F] T3 [39 F] T [57 F] T [8 F] Ambient temperature T a 0 3 3 3 Maximum medium temperature T m 58 66 66 66 The minimum temperature of the medium is 0 C ( F). The minimum ambient temperature is 0 C ( 0 F). Storage temperature Degree of protection The storage temperature corresponds to the ambient temperature range of the transmitter and sensor. Protect the measuring device against direct sunlight during storage in order to avoid unacceptably high surface temperatures. Select a storage location where moisture cannot collect in the measuring device as fungus or bacteria infestation can damage the liner. If protection caps or protective covers are mounted these should never be removed before installing the measuring device. As standard: IP67, type X enclosure Shock resistance Acceleration up to g based on IEC 60068--6 Vibration resistance Acceleration up to g based on IEC 60068--6 Interior cleaning Cleaning in place (CIP) Sterilization in place (SIP) Observe the maximum medium temperatures Electromagnetic compatibility (EMC) According to IEC/EN 636 For details, refer to the Declaration of Conformity. Process Medium temperature range Sensor 0 to +30 C ( to +66 F) Cleaning +50 C (+30 F) / 60 min for CIP and SIP processes Seals EPDM: 0 to +30 C ( to +66 F) (max. +50 C (30 F) for cleaning Silicon: 0 to +30 C ( to +66 F) Viton: 0 to +50 C (+3 to +30 F) Endress+Hauser

[ F] T A [ C] 0 0 00 80 60 0 0 0 60 0 0 0-0 30 50-0 0 0 80 0 60 0 66 30 80 60 0 30 [ C] T M [ F] A000805 T A T M Ambient temperature Medium temperature ight-gray area: standard fluid temperature range Dark-gray area: fluid temperature range for cleaning Conductivity Pressure-temperature ratings 5 μs/cm for liquids in general 0 μs/cmfor demineralized water Permitted process pressure: 6 bar (3 psi) Process connection: Welded connection as per EN 0357 (DIN 850), ODT/SMS; clamp AM7 [psi] 300 00 00 0 [bar] 5 0 PN6 5 0 5 0-60 -0-0 0 0 0 60 80 00006080 [ C] -0 0 00 00 300 360 [ F] 0 Process connection material:.0 (36) (with molded seal) A0090-EN Pressure tightness iner: PFA Nominal diameter imit values for absolute pressure in [mbar] ([psi]) for fluid temperatures: [mm] [in] +5 C (+77 F) +50 C (+30 F) to 5 ⁵ ₃₂ to > mbar (0.0 inh O) (0) > mbar (0.0 inh O) (0) Endress+Hauser 3

Flow limit Pressure loss The diameter of the pipe and the flow rate determine the nominal diameter of the sensor. The optimum flow velocity is between to 3 m/s (6.56 to 9.8 ft/s). Also match the velocity of flow (v) to the physical properties of the fluid: v < m/s (6.56 ft/s): For abrasive media (e.g. cleaning agents) v > m/s (6.56 ft/s): For media that produce buildup (e.g. liquids containing oil and sugar) A necessary increase in the flow velocity can be achieved by reducing the sensor nominal diameter. For an overview of the full scale values for the measuring range, see the "Measuring range" section 6 For DN 8 (5/6"), DN 5 (½") and DN 5 (") no pressure loss occurs if the sensor is installed in a pipe with the same nominal diameter. Pressure losses for configurations incorporating adapters according to DIN EN 55 0 System pressure A00559 Never install the sensor on the pump suction side in order to avoid the risk of low pressure, and thus damage to the liner. Furthermore, install pulse dampers if reciprocating, diaphragm or peristaltic pumps are used. For information on the liner's resistance to partial vacuum 3 For information on the shock resistance of the measuring system For information on the vibration resistance of the measuring system Vibrations In the event of very strong vibrations, the pipe and sensor must be supported and fixed. For information on the shock resistance of the measuring system For information on the vibration resistance of the measuring system Measures to avoid device vibrations ( > 0 m (33 ft)) A00666 Endress+Hauser

Mechanical construction Dimensions in SI units Compact version Order code for "Housing", option B "Compact IP67 NEMAX, stainless steel", DN to 5 (⁵ ₃₂ to ½") A B C H M6 F G K I J D E A000386 A B C D E F G H I J K [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] 33 33. 00 80 86 50 70 90 0 0 d Measuring tube dimensions A00087 DN ) d [mm] [mm] [mm] 9.5 8 9 9 5K ) 9 5 9 6 ) Total installation length depends on process connections ) Conical version (corresponds to DN ) Endress+Hauser 5

Order code for "Housing", option B "Compact IP67 NEMAX, stainless steel", DN 5 (") A B C H M6 I G F K J D E A005867 A B C D E F G H I J K [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] 33 33. 00 80 86 55 0 90 7 55.5 0 d 3 Measuring tube dimensions A005957 DN ) d [mm] [mm] [mm] 5 9.6(ASME) 5 9 6 (DIN) ) Total length depends on process connections Welded connections 6 Endress+Hauser

With O-ring seal G di H B A000557 Welded connection as per DIN EN ISO 7.0 (36) Order code for "Process connection", option B DN Suitable for pipe DIN EN ISO 7 di G H B [mm] [mm] [mm] [mm] [mm] [mm] 8 3.5.6 0.3 3.5 0.3 6 5K ) 5.3.6 8..3 0.3 6 Total length = ( ) + 86 mm ) Conical version (corresponds to DN ) G di H B A000558 Welded connection as per ODT/SMS.0 (36) Order code for "Process connection", option C DN Suitable for pipe ODT/SMS di G H B [mm] [mm] [mm] [mm] [mm] [mm] 8 3.5.30 9 3.5 0.3 6 5K ) 5.3.65 6.3 0.3 6 Total length = ( ) + 86 mm ) Conical version (corresponds to DN ) Endress+Hauser 7

With aseptic molded seal: G di H B A0003870 Welded connection EN 0357 (DIN 850).0 (36): Order code for "Process connection", option U DN sensor Suitable for pipe EN 0357 (DIN 850) di G H x B [mm] [mm] [mm] [mm] [mm] [mm] 8 5K ) 5 3.5 0 3 3 60 9.5 6 9 3 60 5 30 6 30 3.3 7 55 Total length = ( ) + 86 mm It is essential to take the internal diameters of the measuring tube and process connection (di) into account when cleaning with pigs! ) Conical version (corresponds to DN ) G di H B A000387 Weld-in nipple ODT/SMS.0 (36): Order code for "Process connection", option V DN sensor Suitable for pipe ODT/SMS di G H x B [mm] [mm] [mm] [mm] [mm] [mm] 8 5K ) 5.7.65 9.7 6. 60 9..65 6 9. 6. 60 8 Endress+Hauser

Weld-in nipple ODT/SMS.0 (36): Order code for "Process connection", option V DN sensor Suitable for pipe ODT/SMS di G H x B [mm] [mm] [mm] [mm] [mm] [mm] 5 5..65.6 5. 6. 7 55 Total length = ( ) + 86 mm It is essential to take the internal diameters of the measuring tube and process connection (di) into account when cleaning with pigs! ) Conical version (corresponds to DN ) Clamp connections G di H B A000387 Tri-Clamp AM7.0 (36): Order code for "Process connection", option DN sensor Suitable for pipe ODT di G H x B [mm] [mm] [mm] [mm] [mm] [mm] 8 5K ) 5.7.65 9. 5.0 8.5 60 9..65 5.8 5.0 8.5 60 5 5..65. 50. 8.5 7 55 Total length = ( ) + 86 mm It is essential to take the internal diameters of the measuring tube and process connection (di) into account when cleaning with pigs! ) Conical version (corresponds to DN ) Endress+Hauser 9

Tri-Clamp " AM7.0 (36): Order code for "Process connection", option 8 DN sensor Suitable for pipe ODT di G H x B [mm] [mm] [mm] [mm] [mm] [mm] 5K ) 5 Pipe 5..65. 50. 8.5 7 55 5 Pipe 5..65. 50. 8.5 7 55 Total length = ( ) + 86 mm It is essential to take the internal diameters of the measuring tube and process connection (di) into account when cleaning with pigs! ) Conical version (corresponds to DN ) d G d H x B A0003878 Tri-Clamp 3/" (conical) AM7.0 (36): Order code for "Process connection", option DN sensor Suitable for pipe ODT d d G H x B [mm] [mm] [mm] [mm] [mm] [mm] [mm] 8 Pipe 9..65 9 5.8 5.0 8.5 60 Total length = ( ) + 86 mm It is essential to take the internal diameters of the measuring tube and process connection (di) into account when cleaning with pigs! Cable glands With O-ring seal S D di G H B A0005565 30 Endress+Hauser

internal thread as per ISO 8/DIN 999.0 (36) Order code for "Process connection", option DN Suitable for external thread ISO 8 / DIN 999 di G D S H B [mm] [in] [mm] [in] [mm] [mm] [mm] [mm] 8 Rp 3/8 9 3/8 5 3 6 5K ) 5 Rp ½ 6 ½ 7 5 6 Total length = ( ) + 86 mm ) Conical version (corresponds to DN ) Dimensions in US units Compact version Order code for "Housing", option B "Compact IP67 NEMAX, stainless steel", DN to 5 (⁵ ₃₂ to ½") A B C H M6 F G K I J D E A000386 A B C D E F G H I J K [in] [in] [in] [in] [in] [in] [in] [in] [in] [in] [in] [in] 5..3 3.9 0.7 3.5 3.39.97.76 3.5 8.7.65 0.39 Endress+Hauser 3

d Measuring tube dimensions A00087 DN ) d [in] [in] [in] ⁵ ₃₂ 3.70 0.7 ⁵ ₁₆ 3.70 0.35 ½K ) 3.70 0.7 ½ 3.70 0.63 ) Total length depends on process connections ) Conical version (corresponds to DN ) Order code for "Housing", option B "Compact IP67 NEMAX, stainless steel", DN 5 (") A B C H M6 I G F K J D E A005867 A B C D E F G H I J K [in] [in] [in] [in] [in] [in] [in] [in] [in] [in] [in] [in] 5..3 3.9 0.7 3.5 3.39.7.0 3.5 9.7.9 0.39 3 Endress+Hauser

d 5 Measuring tube dimensions A005957 DN ) d [in] [in] [in] 3.70 0.89 (ASME) 3.70.0 (DIN) ) Total length depends on process connections Welded connections With O-ring seal G di H B A000558 Welded connection as per ODT/SMS.0 (36) Order code for "Process connection", option C DN Suitable for pipe ODT/SMS di G H B [in] [in] [in] [in] [in] [in] ⁵ ₁₆ 0.53 0.09 0.35 0.53 0.80..65 ½K ) ½ 0.8 0.0 0.63 0.8 0.80..65 Total length = ( ) + 3.39 in ) Conical version (corresponds to DN ) Endress+Hauser 33

With aseptic molded seal: G di H B A0003870 Welded connection EN 0357 (DIN 850).0 (36): Order code for "Process connection", option U DN sensor Suitable for pipe EN 0357 (DIN 850) di G H x B [in] [in] [in] [in] [in] [in] ⁵ ₃₂ ⁵ ₁₆ ½K ) ½ 0.5 0.06 0.39 0.5 0.9.36.65 0.75 0.06 0.63 0.75 0.9.36.65.8 0.08.0.8 0.9.83.6 Total length = ( ) + 3.39 in It is essential to take the internal diameters of the measuring tube and process connection (di) into account when cleaning with pigs! ) Conical version (corresponds to DN ) G di H B A000387 Weld-in nipple ODT/SMS.0 (36): Order code for "Process connection", option V DN sensor Suitable for pipe ODT/SMS di G H x B [in] [in] [in] [in] [in] [in] ⁵ ₃₂ ⁵ ₁₆ ½K ) ½ 0.50 0.06 0.35 0.50 0.63.36.65 0.75 0.06 0.63 0.75 0.63.36.65 3 Endress+Hauser

Weld-in nipple ODT/SMS.0 (36): Order code for "Process connection", option V DN sensor Suitable for pipe ODT/SMS di G H x B [in] [in] [in] [in] [in] [in] 0.06 0.89 0.63.83.6 Total length = ( ) + 3.39 in It is essential to take the internal diameters of the measuring tube and process connection (di) into account when cleaning with pigs! ) Conical version (corresponds to DN ) Clamp connections G di H B A000387 Tri-Clamp AM7.0 (36): Order code for "Process connection", option DN sensor Suitable for pipe ODT di G H x B [in] [in] [in] [in] [in] [in] ⁵ ₃₂ ⁵ ₁₆ ½K ) ½ ODT ½ 0.37 0.98..36.65 ODT ¾ 0.6 0.6..36.65 ODT 0.87.98..83.6 Total length = ( ) + 3.39 in It is essential to take the internal diameters of the measuring tube and process connection (di) into account when cleaning with pigs! ) Conical version (corresponds to DN ) Endress+Hauser 35

Tri-Clamp " AM7.0 (36): Order code for "Process connection", option 8 DN sensor Suitable for pipe ODT di G H x B [in] [in] [in] [in] [in] [in] ½K ) ½ 0.87.98..83.6 0.87.98..83.6 Total length = ( ) + 3.39 in It is essential to take the internal diameters of the measuring tube and process connection (di) into account when cleaning with pigs! ) Conical version (corresponds to DN ) d G d H x B A0003878 Tri-Clamp 3/" (conical) AM7.0 (36): Order code for "Process connection", option DN sensor Suitable for pipe ODT d d G H x B [in] [in] [in] [in] [in] [in] [in] ⁵ ₃₂ ⁵ ₁₆ ODT ¾ 0.35 0.6..36.65.36.65 Total length = ( ) + 3.39 in It is essential to take the internal diameters of the measuring tube and process connection (di) into account when cleaning with pigs! Cable glands With O-ring seal S D di G H B A0005565 36 Endress+Hauser

internal thread as per ISO 8/DIN 999.0 (36) Order code for "Process connection", option DN Suitable for external thread ISO 8 / DIN 999 di G D S H B [in] [in] [in] [in] [in] [in] [in] [in] ⁵ ₁₆ Rp 3/8 0.35 3/8 0.87.77 0.5..65 ½K ) ½ Rp ½ 0.63 ½.06.77 0.55..65 Total length = ( ) + 3.39 in ) Conical version (corresponds to DN ) Weight Compact version Weight in SI units DN [mm] Weight [kg].8 8.8 5.8 5.3 Weight in US units DN [in] Weight [lbs] ⁵ ₃₂ 6.7 ⁵ ₁₆ 6.7 ½ 6.7 9.8 Materials Transmitter housing Acid and alkali-resistant outer surface Stainless steel.308 (30) Device plugs Electrical connection Plug Mx Material Socket: Stainless steel,.0 (36) Contact housing: Polyamide Contacts: Gold-plated brass Sensor housing Acid and alkali-resistant outer surface Stainless steel.30 (30) Measuring tube Stainless steel.30 (30) iner PFA Endress+Hauser 37

Electrodes.35 (36) Alloy C,.60 (UNS N060) Platinum Tantalum Process connections Weld-in nipple:.0 (36) Weld-in nipple, aseptic:.0 (36) Tri-Clamp:.0 (36) Couplings:.0 (36) ist of all available process connections 38 Seals Molded seal (EPDM, silicone, Viton) Fitted electrodes Process connections Standard: stainless steel.35 (36) Optional: Alloy C,.60 (UNS N060), platinum, tantalum With O-ring seal Welded connections DIN EN ISO 7 ODT/SMS Coupling ISO 8/DIN 999 With aseptic molded seal: Welded connections EN 0357, DIN 850 ODT/SMS Tri-Clamp AM7 For information on the different materials used in the process connections 38 Surface roughness Stainless steel electrodes,.35 (30); Alloy C,.60 (UNS N060), platinum, tantalum: 0.3 to 0.5 µm (.8 to 9.7 µin) iner with PFA: 0. µm (5.7 µin) Process connection: 0.8 µm (3 µin) (All data relate to parts in contact with fluid) Operability ocal operation Remote operation This device cannot be operated locally using a display or operating elements. Via service adapter and Commubox FXA9 The Endress+Hauser service and configuration software FieldCare or DeviceCare can be used for operation and configuration. The device is connected by means of a service adapter and a Commubox FXA9 to the computer's USB interface. 38 Endress+Hauser

3 + - 5 A00038 Supply voltage V DC Service adapter 3 Dosimag Commubox FXA9 5 Computer with "FieldCare" or "DeviceCare" operating tool The service adapter, cable and Commubox FXA9 are not included in the delivery. These components can be ordered as accessories 0. Certificates and approvals CE mark C-Tick symbol Ex approval The measuring system is in conformity with the statutory requirements of the applicable EC Directives. These are listed in the corresponding EC Declaration of Conformity along with the standards applied. Endress+Hauser confirms successful testing of the device by affixing to it the CE mark. The measuring system meets the EMC requirements of the "Australian Communications and Media Authority (ACMA)". The measuring device is certified for use in hazardous areas and the relevant safety instructions are provided in the separate "Safety Instructions" (XA) document. Reference is made to this document on the nameplate. The separate Ex documentation (XA) containing all the relevant explosion protection data is available from your Endress+Hauser sales center. ATEX, IECEx Currently, the following versions for use in hazardous areas are available: Ex na Category II3G Type of protection Ex na IIC T5 to T Gc ccsaus Currently, the following versions for use in hazardous areas are available: Class I Division Groups ABCD Sanitary compatibility 3A approval and EHEDG-certified Seals FDA-compliant Endress+Hauser 39

Pressure Equipment Directive Measuring instrument approval Other standards and guidelines With the PED/G/x (x = category) marking on the sensor nameplate, Endress+Hauser confirms compliance with the "Essential Safety Requirements" specified in Annex I of the Pressure Equipment Directive 97/3/EC. Devices bearing this marking (PED) are suitable for the following types of medium: Media in Group and with a vapor pressure greater than, or smaller and equal to0.5 bar (7.3 psi) Devices not bearing this marking (PED) are designed and manufactured according to good engineering practice. They meet the requirements of Art.3 Section 3 of the Pressure Equipment Directive 97/3/EC. The range of application is indicated in tables 6 to 9 in Annex II of the Pressure Equipment Directive. Dosimag is suitable as an (optional) component for recording volume in legally regulated measuring systems for AdBlue / DEF (Diesel Exhaust Fluid) in accordance with Appendix MI-005 of the European Measuring Instruments Directive 0/3/EU. Dosimag is certified in accordance with OIM R7-:007 / OIM R7-:0 and has an MID evaluation certificate confirming conformity with the basic requirements of the Measuring Instruments Directive. EN 6059 Degrees of protection provided by enclosures (IP code) EN 600- Safety Requirements for Electrical Equipment for Measurement, Control and aboratory Use IEC/EN 636 Emission in accordance with Class A requirements. Electromagnetic compatibility (EMC requirements). CAN/CSA C. No. 600-- Safety Requirements for Electrical Equipment for Measurement, Control and aboratory Use, Part : General Requirements ANSI/ISA-600- (8.0.0) Safety Requirements for Electrical Equipment for Measurement, Control and aboratory Use Part : General Requirements Ordering information Detailed ordering information is available from the following sources: In the Product Configurator on the Endress+Hauser website: www.endress.com Select your country Products Select measuring technology, software or components Select the product (picklists: measurement method, product family etc.) Device support (right-hand column): Configure the selected product The Product Configurator for the selected product opens. From your Endress+Hauser Sales Center: www.addresses.endress.com Product Configurator - the tool for individual product configuration Up-to-the-minute configuration data Depending on the device: Direct input of measuring point-specific information such as measuring range or operating language Automatic verification of exclusion criteria Automatic creation of the order code and its breakdown in PDF or Excel output format Ability to order directly in the Endress+Hauser Online Shop Accessories Various accessories, which can be ordered with the device or subsequently from Endress+Hauser, are available for the device. Detailed information on the order code in question is available from your local Endress+Hauser sales center or on the product page of the Endress+Hauser website: www.endress.com. 0 Endress+Hauser

Device-specific accessories For the sensor Accessories Description Order code Seal set For regular replacement of the seals on the process connections. DK5G**-*** Housing seal To seal the transmitter 500857 Mounting set Consists of: process connections Screws Seals DKH**-**** Communication-specific accessories Accessories FieldCare DeviceCare Commubox FXA9 Adapter connection Connecting cable RSE8 Description FDT-based plant asset management tool from Endress+Hauser. It can configure all smart field units in your system and helps you manage them. By using the status information, it is also a simple but effective way of checking their status and condition. For details, see Operating Instructions BA0007S and BA00059S Tool for connecting and configuring Endress+Hauser field devices. For details, see Innovation brochure IN007S Connects Endress+Hauser field devices with a CDI interface (= Endress+Hauser Common Data Interface) and the USB port of a computer or laptop. For details, see the "Technical Information" document TI05C/07 Adapter connections for installation on other electrical connections: Adapter FXA9 (order number: 7035809) Adapter RSE8 (order number: 500769) RSE8 connection jack, 8-pin adapter (RSE8), V DC, pulse, status Adapter RSE5 (order number: 500768 ) RSE8 connection jack, 5-pin adapter (RSE5), V DC, pulse, status Adapter RSE (order number: 500767) RSE8 connection jack, -pin adapter (RSE), V DC, pulse Cable RKWTN8-56/5 P9, length: 5 m (Order number: 5007895) Service-specific accessories Accessories Description Applicator W@M Software for selecting and sizing Endress+Hauser measuring devices: Calculation of all data required to determine the optimum flowmeter: e.g. nominal diameter, pressure loss, accuracy or process connections. Graphic illustration of the calculation results Administration, documentation and access to all project-related data and parameters throughout the entire life cycle of a project. Applicator is available: Via the Internet: https://wapps.endress.com/applicator On CD-ROM for local PC installation. ife cycle management for your plant W@M supports you with a wide range of software applications over the entire process: from planning and procurement, to the installation, commissioning and operation of the measuring devices. All the relevant information is available for every measuring device over time entire life cycle, such as the Device status, spare parts, device-specific documentation. The application already contains the data of your Endress+Hauser device. Endress +Hauser also takes care of maintaining and updating the data records. W@M is available: Via the Internet: www.endress.com/lifecyclemanagement On CD-ROM for local PC installation. Endress+Hauser

FieldCare DeviceCare Commubox FXA9 FDT-based plant asset management tool from Endress+Hauser. It can configure all smart field units in your system and helps you manage them. By using the status information, it is also a simple but effective way of checking their status and condition. For details, see Operating Instructions BA0007S and BA00059S Tool for connecting and configuring Endress+Hauser field devices. For details, see Innovation brochure IN007S Connects Endress+Hauser field devices with a CDI interface (= Endress+Hauser Common Data Interface) and the USB port of a computer or laptop. For details, see "Technical Information" TI0005C Supplementary documentation For an overview of the scope of the associated Technical Documentation, refer to the following: The CD-ROM provided for the device (depending on the device version, the CD-ROM might not be part of the delivery!) The W@M Device Viewer : Enter the serial number from the nameplate (www.endress.com/deviceviewer) The Endress+Hauser Operations App: Enter the serial number from the nameplate or scan the -D matrix code (QR code) on the nameplate. Standard documentation Brief Operating Instructions Measuring device Dosimag Documentation code KA075D Operating Instructions Measuring device Documentation code Pulse/frequency/status output Option 3 Modbus RS85 Options, 5 and 6 Dosimag BA00098D BA03D Description of device parameters Measuring device Documentation code Pulse/frequency/status output Option 3 Modbus RS85 Options, 5 and 6 Dosimag GP009D GP008D Supplementary devicedependent documentation Safety Instructions Contents Documentation code ATEX/IECEx Ex na ccsaus U Class Division XA033D FES03 XA0377D Endress+Hauser

Special Documentation Contents Information on Custody Transfer Measurement Documentation code SD05D Registered trademarks Modbus Registered trademark of SCHNEIDER AUTOMATION, INC. TRI-CAMP Registered trademark of adish & Co., Inc., Kenosha, USA Applicator, FieldCare, DeviceCare Registered or registration-pending trademarks of the Endress+Hauser Group Endress+Hauser 3

www.addresses.endress.com