General Specifications

General Specifications GS 0121F01-02E odel EJ530/H Gauge Pressure Transmitter (High ccuracy Type) [Style: S2] The gauge pressure transmitter model EJ530/H can be used to measure liquid, gas, or steam pressure. oth output a 4 to 20 m signal corresponding to the measured pressure, and also feature remote setup and monitoring through communications with the RIN terminal and ENTU S or µxl or HRT 275 host. STNR SPEIFITIONS Refer to GS 0122T02-00E for Fieldbus communication type marked with. PERFORNE SPEIFITIONS Zero-based calibrated span, linear output, wetted parts material code S and silicone oil. Reference ccuracy of alibrated Span (including the effects of zero-based linearity, hysteresis, and repeatability) 0.075 % of Span, (, and capsule) 0.12 % of Span, ( capsule) For spans below X, [0.025 0.05 X ] % of span, (, and capsule) Span X [0.03 0.09 ] % of span, ( capsule) Span Where X equals: apsule X Pa {psi} 40 kpa {5.8} 0.2 {29} 1 {145} 8 {1160} mbient Temperature Effects Total Effects per 28 (50 F) hange [0.15% Span 0.15% URL] Stability 0.1% of URL per 12 months Vibration Effects 0.1 % of URL (5 to 15Hz; 4mm peak-to-peak constant displacement, 15 to 150Hz; 2g, 150 to 2000Hz; 1g) Power Supply Effects 0.005 % per Volt (from 21.6 to 32 V, 350 ) FUNTIONL SPEIFITIONS Span & Limits easurement Span and Pa psi (/1) bar (/3) Span Span 10 to 200 kpa 0.1 to 2 1.45 to 29 14.5 to 290 0.1 to 2 1 to 20 0 to 200 kpa 0 to 2 0 to 29 0 to 290 0 to 2 0 to 20 Span 0.5 to 10 72.5 to 1450 5 to 100 0 to 10 0 to 1450 0 to 100 Span 5 to 50 720 to 7200 50 to 500 0 to 50 0 to 7200 0 to 500 kgf/cm 2 (/4) 0.1 to 2 0 to 2 1 to 20 0 to 20 5 to 100 0 to 100 50 to 500 0 to 500 T01E.EPS URL is defined as the Upper Limit from the table above. Zero djustment Limits Zero can be fully elevated or suppressed, within the Lower and Upper Limits of the capsule. External Zero djustment External zero is continuously adjustable with 0.01 % incremental resolution of span. Span may be adjusted locally using the digital indicator with range switch. ounting Position Effect Rotation in diaphragm plane has no effect. Tilting up to 90 will cause zero shift up to 0.27 kpa {1.1 inh 2 O} which can be corrected by the zero adjustment. Output Two wire 4 to 20 m output with digital communications. RIN or HRT FSK protocol are superimposed on the 4 to 20 m signal. Failure larm Output status at PU failure and hardware error; Up-scale: 110%, 21.6 m or more (standard) own-scale: -5%, 3.2 m or less Note : pplicable for Output signal code and E. Yokogawa Electric orporation 2-9-32, Nakacho, usashino-shi, Tokyo, 180-8750 Japan Phone: 81-422-52-5690 Fax.: 81-422-52-2018 GS 0121F01-02E opyright pr. 2002 5th Edition pr. 2003

amping Time onstant (1st order) The sum of the amplifier and capsule damping time constant must be used for the overall time constant. mp damping time constant is adjustable from 0.2 to 64 seconds. apsule (Silicone Oil),,, and Time onstant (approx. sec) 0.2 mbient Temperature Limits (approval codes may affect limits) -40 to 85 (-40 to 185 F) -30 to 80 (-22 to 176 F) with L isplay Process Temperature Limits (approval codes may affect limits) -40 to 120 (-40 to 248 F) mbient Humidity Limits 5 to 100 % RH @ 40 (104 F) aximum Overpressure apsule Pressure 4 Pa {580 psig} 4 Pa {580 psig} 20 Pa {2900 psig} 60 Pa {8500 psig} Working Pressure Limits (Silicone Oil) aximum Pressure Limit apsule Pressure 200 kpa {29 psig} 2 Pa {290 psig} 10 Pa {1450 psig} 50 Pa {7200 psig} Supply & Load Requirements (Safety approvals can affect electrical requirements, see graph below) With 24 V supply, up to a 570 load can be used. Supply Voltage 10.5 to 42 V for general use and flameproof type 10.5 to 32 V for lightning protector (Optional code /) 10.5 to 30 V for intrinsically safe, Type n, nonincendive, or non-sparking type inimum voltage limited at 16.4 V for digital communications, RIN and HRT Load (Output signal code and E) 0 to 1335 for operation 250 to 600 for digital communication E onformity Standards:, EN61326, S/NZS 2064 European Pressure Equipment irective 97/23/E ategory III, odule H, Type of Equipment: Pressure ccessory-vessel, Type of Fluid: Liquid and Gas, Group of Fluid: 1 and 2 ommunication Requirements RIN ommunication istance Up to 2 km (1.25 miles) when using EV polyethylene-insulated PV-sheathed cables. ommunication distance varies depending on type of cable used. Load apacitance 0.22 F or less (see note) Load Inductance 3.3 mh or less (see note) Input Impedance of communicating device 10 k or more at 2.4 khz. Note : For general-use and Flameproof type. For Intrinsically safe type, please refer to OPTIONL SPEIFITIONS. 2 HRT ommunication istance Up to 1.5 km (1 mile) when using multiple twisted pair cables. ommunication distance varies depending on type of cable used. R ( ) 600 External load resistance 250 R= E-10.5 0.0236 igital ommunication range Use the following formula to determine cable length for specific applications: 65 x 10 L= 6 - (R x ) ( f + 10,000) Where: L = length in meters or feet R = resistance in (including barrier resistance) = cable capacitance in pf/m or pf/ft f = maximum shunt capacitance of receiving devices in pf/m or pf/ft 10.5 16.4 24.7 42 Power supply voltage E (V ) F01E.EPS Figure 1. Relationship etween Power Supply Voltage and External Load Resistance ll Rights Reserved. opyright 2002, Yokogawa Electric orporation GS 0121F01-02E Oct. 01, 2002-00

3 PHYSIL SPEIFITIONS Wetted Parts aterials: iaphragm and Process connector Refer to OEL N SUFFIX OE. Non-wetted Parts aterials: Housing Low copper cast-aluminum alloy with polyurethane paint (unsell 0.6GY3.1/2.0) egrees of Protection IP67, NE4X, JIS 0920 immersion proof over O-rings una-n ata plate and tag SUS304 Fill Fluid Silicone, Fluorinated oil (option) Weight 1.6 kg (3.5 lb) without integral indicator, mounting bracket. onnections Refer to the model code to specify the process and the electrical connection type. < Settings When Shipped > Tag Number Output ode isplay ode Operation ode amping Time onstant alibration Lower Value alibration Higher Value alibration Units s specified in order *1 Linear Linear Normal unless otherwise specified in order 2 sec. s specified in order s specified in order Selected from mmh 2 O, mmq, mmwg, mmhg, Torr, Pa, hpa, kpa, Pa, mbar, bar, gf/cm 2, kgf/cm 2, inh 2 O, inhg, fth 2 O, psi, or atm.(only one unit can be specified) *1: Up to 16 alphanumeric characters (including - and ) for Output Signal code or up to 8 alphanumeric characters for Output Signal code E will be entered in the amplifier memory. T05E.EPS ll Rights Reserved. opyright 2002, Yokogawa Electric orporation GS 0121F01-02E Oct. 01, 2002-00

4 OEL N SUFFIX OES odel EJ530 odel EJ530 Output Signal easurement span (capsule) Wetted parts material Process connection Electrical connection Integral indicator ounting bracket High accuracy Optional codes Suffix odes.................... -................. -E................. -F..................................................................................... S............... H............... 4.............. 7.............. 8.............. 9.............. N............ -0........... 0.......... 2.......... 3.......... 4.......... 5.......... 7.......... 8.......... 9.................. E........ N........ E....... F....... N....... /H... escription Gauge pressure transmitter 4 to 20 m with digital communication (RIN protocol) 4 to 20 m with digital communication (HRT protocol, refer to GS 0122T01-00E) igital communication (FOUNTION Fieldbus protocol, refer to GS 0122T02-00E) 10 to 200 kpa{0.1 to 2 kgf/cm 2 } 0.1 to 2 Pa{1 to 20 kgf/cm 2 } 0.5 to 10 Pa{5 to 100 kgf/cm 2 } 5 to 50 Pa{50 to 500 kgf/cm 2 } [Process onnection] [iaphragm] SUS316L Hastelloy -276 Hastelloy -276 Hastelloy -276 1/2 NPT female 1/2 NPT male G 1/2 IN 16 288 male 2031.5 IN 16 288 male lways N lways 0 G1/2 female, one electrical connection 1/2 NPT female, two electrical connections without blind plug Pg 13.5 female, two electrical connections without blind plug 20 female, two electrical connections without blind plug G1/2 female, two electrical connections and a blind plug 1/2 NPT female, two electrical connections and a blind plug Pg 13.5 female, two electrical connections and a blind plug 20 female, two electrical connections and a blind plug igital indicator igital indicator with the range setting switch * 1 (None) SE arbon steel 2-inch pipe mounting SUS304 2-inch pipe mounting (None) lways /H / Optional specification T02E.EPS The marks indicate the most typical selection for each specification. Example: EJ530-S4N-02NN/H/ *1: Not applicable for Output signal code F ll Rights Reserved. opyright 2002, Yokogawa Electric orporation GS 0121F01-02E July 01, 2002-00

5 OPTIONL SPEIFITIONS (For Explosion Protected types ) For FOUNTION Fieldbus explosion protected type, see GS 0122T02-00E. Item escription ode Factory utual (F) ENELE TEX anadian Standards ssociation (S) Standards ssociation of ustralia (S) F Explosionproof pproval * 1 * 3 Explosionproof for lass I, ivision 1, Groups, and ust-ignitionproof for lass II/III, ivision 1, Groups E, F and G Hazardous (classified) locations, indoors and outdoors (NE 4X) Temperature class: T6 mb. Temp.: 40 to 60 ( 40 to 140 F) F Intrinsically safe pproval * 1 * 3 Intrinsically Safe for lass I, ivision 1, Groups,, &, lass II, ivision 1, Groups E, F & G and lass III, ivision 1 Hazardous Locations. Nonincendive for lass I, ivision 2, Groups,, &, lass II, ivision. 2, Groups E, F & G, and lass III, ivision 1 Hazardous Locations. Enclosure: "NE 4X", Temp. lass: T4, mb. Temp.: 40 to 60 ( 40 to 140 F) Intrinsically Safe pparatus Parameters [Groups,,,, E, F and G] Vmax=30 V, Imax=165 m, Pmax=0.9 W, i=22.5 nf, Li=730 H [Groups,, E, F and G] Vmax=30 V, Imax=225 m, Pmax=0.9 W, i=22.5 nf, Li=730 H ombined FF1 and FS1 * 1 * 3 ENELE TEX (KE) Flameproof pproval * 2 * 3 II 2G EExd II T4, T5, T6 mb. Temp.: T5; 40 to 80 ( 40 to 176 F), T4 and T6; 40 to 75 ( 40 to 167 F) ax. process Temp.: T4; 120 (248 F), T5; 100 (212 F), T6; 85 (185 F) ENELE TEX (KE) Intrinsically safe pproval * 2 * 3 II 1G EEx ia II T4, mb. Temp.: 40 to 60 ( 40 to 140 F) Ui=30 V, Ii=165 m, Pi=0.9 W, i=22.5 nf, Li=730 H ombined KF2, KS2 and Type n * 2 * 3 Type n: II 3G Ex nl II T4, mb. Temp.: 40 to 60 ( 40 to 140 F) Ui=30 V, i=22.5 nf, Li=730 H ust: II 1 maximum surface temperature T65 (149 F) {Tamb.: 40 (104 F)}, T85 (185 F) {Tamb.: 60 (140 F)}, T105 (221 F) {Tamb.: 80 (176 F)} S Explosionproof pproval * 1 * 3 Explosionproof for lass I, ivision 1, Groups, and ustignitionproof for lass II/III, ivision 1, Groups E, F and G ivision2 'SELS NOT REQUIRE', Temp. lass: T4, T5, T6 Encl Type 4x ax. Process Temp.: T4; 120 (248 F), T5; 100 (212 F), T6; 85 (185 F) mb. Temp.: 40 to 80 ( 40 to 176 F) S Intrinsically safe pproval * 1 * 3 lass I, Groups,, and lass II and III, Groups E, F and G Encl Type 4x, Temp. lass: T4, mb. Temp.: 40 to 60 ( 40 to 140 F) Vmax=30 V, Imax=165 m, Pmax=0.9 W, i=22.5 nf, Li=730 H ombined F1 and S1 * 1 * 3 S Flameproof, Intrinsically safe and Non-sparking pproval * 3 * 4 Ex d II T4/T5/T6, IP67, mb. Temp.: 40 to 80 ( 40 to 176 F) ax. Process Temp.: T4; 120 (248 F), T5; 100 (212 F), T6; 85 (185 F) Ex ia II T4, IP67 Ex n II T4, IP67 Ui=30 V, Ii=165 m, Wi=0.9 W, mb. Temp.: 40 to 60 ( 40 to 140 F) *1: pplicable for Electrical connection code 2 and 7 (1/2 NPT female). *2: pplicable for Electrical connection code 2, 4, 7 and 9 (1/2 NPT and 20 female). *3: pplicable for Output signal code and E. For intrinsically safe approval, use the safety barrier certified by the testing laboratories (R-400 is not applicable). *4: pplicable for Electrical connection code 2, 3, 4, 7, 8 and 9 (1/2 NPT, Pg 13.5, and 20 female). FF1 FS1 FU1 KF2 KS2 KU2 F1 S1 U1 SU1 T03E.EPS ll Rights Reserved. opyright 2002, Yokogawa Electric orporation GS 0121F01-02E pr. 01, 2003-00

6 OPTIONL SPEIFITIONS Painting Lightning protector Oil-prohibited use alibration units * 1 Fast response * 9 Item escription ode olor change oating change Failure alarm down-scale * 2 NUR NE43 compliant * 2 * 10 Stainless steel amplifier housing * 3 ill ertificate Pressure test/leak test ertificate mplifier cover only Epoxy resin-baked coating Transmitter power supply voltage: 10.5 to 32 V (10.5 to 30 V for intrinsically safe type, 9 to 32 V for Fieldbus communication type.) llowable current: ax. 6000 (1 40 ms), Repeating 1000 (1 40 ms) 100 times egrease cleansing treatment egrease cleansing treatment and with fluorinated oil filled capsule. Operating temperature 20 to 80 P calibration (psi unit) bar calibration (bar unit) calibration (kgf/cm 2 unit ) Update time: 0.125 sec or less mplifier damping time constant: 0.1 to 64 sec in 9 increments Response time (with min. damping time constant): max. 0.3 sec Output status at PU failure and hardware error is 5%, 3.2 m or less. Output signal limits: 3.8 m to 20.5 m Process connector (See Table for Span and Limits.) mplifier housing material; SS14 stainless steel (equivalent to SUS316 cast stainless steel or ST F-8) Test Pressure: 200 kpa (2 kgf/cm 2 ) * 4 Test Pressure: 2 Pa (20 kgf/cm 2 ) * 5 Test Pressure: 10 Pa (100 kgf/cm 2 ) * 6 Test Pressure: 50 Pa (500 kgf/cm 2 ) * 7 Failure alarm down-scale: output status at PU failure and hardware error is 5%, 3.2 m or less. Failure alarm up-scale: output status at PU failure and hardware error is 110%, 21.6 m or more. Stainless steel tag plate SUS304 stainless steel tag plate wired onto transmitter N4 European Pressure Equipment irective * 11 PE 97/23/E ategory: III, odule: H, Type of Equipment: Pressure ccessory-vessel, Type of Fluid: Liquid and Gas, Group of Fluid: 1 and 2 Nitrogen (N 2 ) Gas or Water * 8 Retention time: 10 minutes *1: The unit of WP (ax. working pressure) on the name plate of a housing is the same unit as specified by Optional code 1, 3 and 4. *2: pplicable for Output signal code and E. The hardware error indicates faulty amplifier or capsule. When combining with Optional code F1, output status for down-scale is 2.5%, 3.6 m or less. *3: pplicable for Electrical connection code 2, 3, 4, and 7. Not applicable for Optional code P and X1. *4: pplicable for apsule code. *5: pplicable for apsule code. *6: pplicable for apsule code. *7: pplicable for apsule code. *8: Pure nitrogen gas or pure water is used for oil-prohibited use (Optional code K1 and K2) *9: pplicable for Output signal code and E. onsult Yokogawa when combining with Optional code for explosion protected type. *10: Not applicable for Optional code 1. *11: Lower limit of process temperature is 30 when olts and nuts material code is selected. P X1 K1 K2 1 3 4 F1 1 2 3 E1 PE3 15 T05 T06 T07 T08 T04E.EPS ll Rights Reserved. opyright 2002, Yokogawa Electric orporation GS 0121F01-02E Oct. 01, 2002-00

7 IENSIONS odel EJ530 With Process onnection code 7 Unit: mm(pprox. inch) 96(3.77) 41(1.61) onduit connection 12 (0.47) 110(4.33) 45 (1.77) Ground terminal 127(5.0) 170(6.69) 78 (3.07) Zero adjustment LOK ZERO LOK 111(4.37) 124(4.88) dapter Pipe(Open to atmosphere) *1 47 (1.85) 44(1.73) 91(3.58) 2-inch pipe (O.. 60.5 mm) ounting bracket *1: pplied to odel EJ530 with easurement span code,, and. For Process onnection code 4 163(6.41) For Process onnection code 8 and 9 5(0.19) 20(0.78) 176(6.92) φ6(0.23) F02E.EPS Terminal onfiguration Terminal Wiring + SUPPLY Power supply and output terminal HEK + External indicator(ammeter) terminal *2 ommunication Terminals(T200 etc.) onnection hook SUPPLY HEK HEK ETER onnection hook *2 Ground terminal *2: When using an external indicator or a check meter, the internal resistance must be 10 or less. Not available for Fieldbus communication (Output signal code F). F03E.EPS ll Rights Reserved. opyright 2002, Yokogawa Electric orporation GS 0121F01-02E July 01, 2002-00

8 SELETION GUIE pplication ifferential Pressure Flow ifferential Pressure & Liquid Level with Remote Seals Type Traditional-ounting *1 Integral Orifice Extended Flush ombination Traditional-ounting *1 Traditional-ounting *1 Traditional-ounting *1 odel EJ110 EJ115 EJ118N EJ118W EJ118Y raft Traditional-ounting *1 EJ120 ifferential Pressure & Liquid Level Traditional-ounting *1 EJ130 Liquid Level, losed or Open Tank bsolute (vacuum) Pressure Gauge Pressure Gauge Pressure with Remote Seal Gauge Pressure with Remote Seal High Gauge bsolute & Gauge Pressure *3 Flush Extended Extended Flush irect-ounting EJ210 EJ220 EJ310 EJ430 EJ438N EJ438W EJ440 EJ510 EJ530 apsule L HV L H H E H H easurement Span kpa 0.5 to 10 1 to 100 5 to 500 0.14 to 14Pa 1 to 10 2 to 100 20 to 210 2.5 to 100 25 to 500 inh 2 O 2 to 40 4 to 400 20 to 2000 20 to 2000 psi 4 to 40 8 to 400 80 to 830 10 to 400 100 to 2000 0.1 to 1 0.4 to 4 1 to 100 5 to 500 1 to 100 5 to 500 L 0.67 to 10 *2 1.3 to 130 *2 0.03 to 3 Pa *2 0.03 to 3 Pa 0.14 to 14 0.06 to 3 Pa 0.46 to 7 0.06 to 3 Pa 0.46 to 7 5 to 32 Pa 5 to 50 Pa 10 to 200 0.1 to 2 Pa 0.5 to 10 Pa 5 to 50 Pa 4 to 400 20 to 2000 4 to 400 20 to 2000 2.67 to 40 *2 0.38 to 38 inhg *2 4.3 to 430 psi *2 4.3 to 430 psi 20 to 2000 psi 9 to 430 psi 66 to 1000 psi 8 to 430 psi 66 to 2000 psi 720 to 4500 psi 720 to 7200 psi 1.45 to 29 psi 14.5 to 290 psi 72.5 to 1450 psi 720 to 7200 psi aximum Working Pressure Pa 16 *4 16 16 16 3.5 14 14 psi 2250 * 4 2250 2250 2250 500 2000 2000 ased on Flange Rating 50 kpa 7.25 32 32 4500 4500 ased on Flange Rating 10 kpa *2 3000 kpa *2 430 *2 130 kpa *2 40 in H 2 18.65 O*2 3 14 430 2000 ased on Flange Rating ased on Flange Rating 32 50 200 kpa 2 10 50 *1: Traditional-mounting is 1/4-18 NPTF process connections ( 1/2-14 NPTF with process adapters ) on 2-1/8" centers. *2: easurement values in absolute. *3: easurement values in absolute for EJ510. *4: When combined with Wetted parts material code H,, T,,, and, the value is 3.5 Pa (500 psi). 4500 7200 29 290 1450 7200 T06E.EPS < Ordering Information > Specify the following when ordering 1. odel, suffix codes, and optional codes 2. alibration range and units: 1) alibration range can be specified with range value specifications up to 5 digits (excluding any decimal point) for low or high range limits within the range of -32000 to 32000. 2) Specify only one unit from the table, Settings when shipped. 3. Select linear or square root for output mode and display mode. Note: If not specified, the instrument is shipped set for linear mode. 4. Select normal or reverse for operation mode Note: If not specified, the instrument is shipped in normal operation mode. 5. isplay scale and units (for transmitters equipped with integral indicator only) Specify either 0 to 100 % or engineering unit scale and and Unit for engineering units scale: Scale range can be specified with range limit specifications up to 5 digits (excluding any decimal point) for low or high range limits within the range of -19999 to 19999. 6. Tag Number (if required) < Related Instruments > Power istributor: Refer to GS 0104T01-02E or GS 0104T02-00E RIN TERINL: Refer to GS 010011-00E < Reference > 1. Teflon; Trademark of E.I. upont de Nemours & o. 2. Hastelloy; Trademark of Haynes International Inc. 3. HRT; Trademark of the HRT ommunication Foundation. 4. FOUNTION ; Trademark of Fieldbus Foundation. aterial ross Reference Table SUS316L ISI 316L SUS316 SUS304 ISI 316 ISI 304 S25 ISI 1025 S435 ISI 4137 SUS630 ST630 SS14 ST F-8 T07E.EPS < Specification onformance > The model EJ530 maintain a specification conformance to at least 3. ll Rights Reserved. opyright 2002, Yokogawa Electric orporation GS 0121F01-02E Oct. 01, 2002-00