1W Single Output Switching Power Supply HLG-1H series Ⅰ IP65 IP67 SPECIFICATION MODEL OUTPUT INPUT PROTECTION LINE REGULATION LOAD REGULATION ±2.0% ±1.5% SETUP, RISE TIME Note.8 10ms,50ms/115VAC 500ms,50ms/230VAC at full load ; B type 10ms,0ms/115VAC 500ms,0ms/230VAC at 95% load HOLD UP TIME (Typ.) VOLTAGE RANGE Note.5 ms at full load 90 ~ 305VAC 230VAC / 115VAC 7 ~ 431VDC FREQUENCY RANGE 47 ~ 63Hz POWER FACTOR (Typ.) PF>0./115VAC, PF>0.95/230VAC, PF>0.93/277VAC at full load (Please refer to "Power Factor Characteristic" curve) TOTAL HARMONIC DISTORTION THD< % when output loading 50% at 115VAC/230VAC input and output loading 75% at 277VAC input EFFICIENCY (Typ.) AC CURRENT (Typ.) INRUSH CURRENT (Typ.) LEAKAGE CURRENT SAFETY STANDARDS WITHSTAND VOLTAGE SAFETY & ISOLATION RESISTANCE EMC EMC EMISSION OTHERS NOTE HLG-1H- HLG-1H-15 HLG-1H- HLG-1H-24 HLG-1H-30 HLG-1H-36 HLG-1H-42 HLG-1H-48 HLG-1H-54 DC VOLTAGE V 15V V 24V 30V 36V 42V 48V 54V CONSTANT CURRENT REGION Note.4 6 ~ V 7.5 ~ 15V 10 ~ V ~ 24V 15 ~ 30V 18 ~ 36V 21 ~ 42V 24 ~ 48V 27 ~ 54V RATED CURRENT RATED POWER 10A 1W 8A 1W 6A 1W 5A 1W 4A 1W 3.4A 2.4W 2.9A 1.8W 2.5A 1W 2.3A 4.2W RIPPLE & NOISE (max.) Note.2 150mVp-p 150mVp-p 150mVp-p 150mVp-p 0mVp-p 0mVp-p 0mVp-p 0mVp-p 0mVp-p VOLTAGE ADJ. RANGE Note.6 10.8 ~ 13.5V 13.5 ~ 17V 17 ~ 22V 22 ~ 27V 27 ~ 33V 33 ~ 40V 38 ~ 46V 43 ~ 53V 49 ~ 58V CURRENT ADJ. RANGE Can be adjusted by internal potentiometer A type only 5 ~ 10A 4 ~ 8A 3 ~ 6A 2.5 ~ 5A 2 ~ 4A 1.7 ~ 3.4A 1.4 ~ 2.9A 1.2 ~ 2.5A 1.1 ~ 2.3A VOLTAGE TOLERANCE Note.3 ±2.5% ±2.0% ±1.0% ±1.0% ±1.0% ±1.0% ±1.0% ±1.0% ±1.0% MAX. No. of PSUs on 16A CIRCUIT BREAKER OVER CURRENT SHORT CIRCUIT OVER VOLTAGE OVER TEMPERATURE WORKING TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION Note.7 92% 92% 93% 93% 93% 93% 93% 93.5% 93.5% 1.4A / 115VAC 0.6A / 230VAC 0.55A / 277VAC COLD START 60A(twidth=375μs measured at 50% Ipeak) at 230VAC 5 units (circuit breaker of type B) / 9 units (circuit breaker of type C) at 230VAC <0.75mA / 277VAC 95 ~ 108% Protection type : Constant current limiting, recovers automatically after fault condition is removed Constant current limiting, recovers automatically after fault condition is removed 14 ~ 17V 18 ~ 21V 23 ~ 27V 28 ~ V ~ 38V 41 ~ 46V 47 ~ 53V 54 ~ 63V 59 ~ 65V Protection type : Shut down o/p voltage with auto-recovery or re-power on to recovery Shut down o/p voltage, recovers automatically after temperature goes down -40 ~ +70 (Refer to "Derating Curve") ~ 95% RH non-condensing -40 ~ +80, 10 ~ 95% RH ± 0.03%/ (0 ~ 50 ) 10 ~ 500Hz, 5G min./1cycle, period for 72min. each along X, Y, Z axes UL8750(type HL ), CSA C22.2 No. 250.0-08, ENEC, TUV EN617-1, EN617-2-13 independent IP65 or IP67, J617-1, J617-2-13 approved ; design refer to UL60950-1, TUV EN60950-1 I/P-O/P:3.75KVAC I/P-FG:2KVAC O/P-FG:1.5KVAC I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 / 70% RH Compliance to EN55015, EN55022 (CISPR22) Class B, EN61000-3-2 Class C ( 50% load) ; EN61000-3-3 EMC IMMUNITY Compliance to EN61000-4-2,3,4,5,6,8,11, EN61547, EN55024, light industry level (surge 4KV), criteria A MTBF 192.2Khrs min. MIL-HDBK-217F (25 ) DIMENSION 2**mm (L*W*H) PACKING 1.Kg; pcs/14.4kg/0.74cuft File Name:HLG-1H-SPEC 15-07-23
1W Single Output Switching Power Supply HLG-1H series Mechanical Specification Case No.994A Unit:mm Blank:(HLG-1H) 2 A Type:(HLG-1H-_A) IP67 rated. Cable for I/O connection. 9.4 9.4.2 9.4 9.4.2 2 Vo ADJ. Io ADJ. IP65 rated. Output voltage and constant current level can be adjusted through internal potentiometer. (Can access by removing the rubber stopper on the case.) B Type:(HLG-1H-_B) 2 9.4.2 9.4 DIM+(Blue) DIM-(White) File Name:HLG-1H-SPEC 15-07-23
1W Single Output Switching Power Supply HLG-1H series D Type(option):(HLG-1H-_D) 2 9.4 9.4.2 IP67 rated. Timer dimming function, contact MEAN WELL for details. Block Diagram Fosc : 100KHz I/P FG EMI FILTER & RECTIFIERS PFC CIRCUIT PFC CONTROL O.L.P. O.T.P. POWER SWITCHING PWM CONTROL RECTIFIERS & FILTER O.V.P. O.L.P. DETECTION CIRCUIT +V -V DIM+ DIM- (B Type) Derating Curve Static Characteristics 100 80 60 100 90 80 70 LOAD (%) 40 LOAD (%) 60 50 40-40 -25-10 0 15 30 50 60 70 AMBIENT TEMPERATURE ( ) (HORIZONTAL) 90 100 5 135 145 155 165 175 180 0 230 305 INPUT VOLTAGE (V) 60Hz File Name:HLG-1H-SPEC 15-07-23
1W Single Output Switching Power Supply HLG-1H series Power Factor Characteristic PF 1.00 0. 0.96 0.94 0.92 0.90 0.88 0.86 0.84 0.82 0.80 0.78 Constant Current Mode 50% 60% 70% 80% 90% 100% (1W) LOAD 277Vac 230Vac 115Vac EFFICIENCY vs LOAD (48V Model) HLG-1H series possess superior working efficiency that up to 93.5% can be reached in field applications. 96 92 EFFICIENCY (%) 88 84 80 76 72 10% % 30% 40% 50% 60% 70% 80% 90% 100% LOAD 277Vac 230Vac 115Vac DRIVING METHODS OF LED MODULE There are two major kinds of LED drive method "direct drive" and "with LED driver". A typical LED power supply may either work in "constant voltage mode (CV) or constant current mode (CC)" to drive the LEDs. Mean Well's LED power supply with CV+ CC characteristic can be operated at both CV mode (with LED driver, at area (A) and CC mode (direct drive, at area (B). 100 In the constant current region, the highest voltage at the output of the driver depends on the configuration of the end systems. Vo(%) (A) Constant Voltage area (B) Constant Current region Should there be any compatibility issues, please contact MEAN WELL. 50 100 Io (%) Typical LED power supply I-V curve File Name:HLG-1-SPEC 15-07-23
1W Single Output Switching Power Supply HLG-1H series DIMMING OPERATION(for B-type only) HLG-1H DIM+(Blue) DIM-(White) Built-in 3 in 1 dimming function, IP67 rated. Output constant current level can be adjusted through output cable by connecting a resistance or 1 ~ 10Vdc or 10V PWM signal between DIM+ and DIM-. Please DO NOT connect "DIM-" to "-V". Reference resistance value for output current adjustment (Typical) Single driver 10KΩ KΩ 30KΩ 40KΩ 50KΩ 60KΩ 70KΩ 80KΩ 90KΩ 100KΩ OPEN Resistance value Multiple drivers (N=driver quantity for synchronized 10K Ω/N K Ω/N 30K Ω/N 40K Ω/N 50K Ω/N 60K Ω/N 70K Ω/N 80K Ω/N 90K Ω/N 100K Ω/N ----- dimming operation) Percentage of rated current 10% % 30% 40% 50% 60% 70% 80% 90% 100% 95%~108% 1 ~ 10V dimming function for output current adjustment (Typical) Dimming value Percentage of rated current 1V 2V 3V 4V 5V 6V 7V 8V 9V 10V 10% % 30% 40% 50% 60% 70% 80% 90% 100% OPEN 95%~108% 10V PWM signal for output current adjustment (Typical): Frequency range :100Hz ~ 3KHz Duty value 10% % 30% 40% 50% 60% 70% 80% 90% 100% OPEN Percentage of rated current 10% % 30% 40% 50% 60% 70% 80% 90% 100% 95%~108% Using the built-in dimming function on B-type model can't turn the lighting fixture totally dark. Please refer to the connection method below to achieve 0% brightness of the lighting fixture connecting to the LED power supply unit. Direct connecting to LEDs is suggested, but is not suitable for using additional drivers. Dimming connection diagram for turning the lighting fixture ON/OFF : N FG L Relay Switch Adjuster 0~100K Ohms resistance 1~10V DC Voltage 10V PWM Signal Green/ Yellow Brown Blue AC/L AC/N HLG-1H BType DIM+ DIM- V(-) V(+) Blue White Black Red LED Lighting Fixture Using a switch and relay can turn ON/OFF the lighting fixture. 1.Output constant current level can be adjusted through output cable by connecting a resistance or 1~10Vdc or 10V PWM signal between DIM+ and DIM-. 2.The LED lighting fixture can be turned ON/OFF by the switch. File Name:HLG-1H-SPEC 15-07-23
1W Single Output Switching Power Supply HLG-1H series WATERPROOF CONNECTION Waterproof connector Waterproof connector can be assembled on the output cable of HLG-1H to operate in dry/wet/damp or outdoor environment. AC source I/P HLG-1H O/P Size Pin Configuration (Female) Size Pin Configuration (Female) M Order No. Suitable Current 4-PIN 5A/PIN M-04 10A max. 5-PIN 5A/PIN M-05 10A max. M15 Order No. Suitable Current 2-PIN A/PIN M15-02 A max. LED Lamp Cable Joiner 66 26 CJ04-1 suitable for 14AWG~16AWG CJ04-2 suitable for 18AWG~22AWG ψ25 Up to four wires can be connected through this cable joiner by soldering or clamping by tools. LED Lamp HLG-1H O/P Wires CJ04 cable joiner can be purchased independently for user's own assembly. MEAN WELL order No. : CJ04-1, CJ04-2. Junction Box(Option ) 358 76 10 5 61 8.5 32 8.5 6 2-ψ5 3- PF 1/2" 150± 35 3- PF 1/2" 150± Optional junction box available for A / Blank - type, please contact MEAW WELL for details. 86 File Name:HLG-1H-SPEC 15-07-23