Bauar t gepruft Sicherheit egelma ge od o s be wac g www. tuv.com ID 000000000 W Constant Voltage Constant Current LED Driver F 110 M M SELV IP65 IP67 Type HL (except for BL type) (for HLGH48/54BL only) (for HLGH1~4BL only) ( Optional ) S&E Features Constant Voltage Constant Current mode output Metal housing with class I design Builtin active PFC function Class power unit IP67 / IP65 rating for indoor or outdoor installations Function options: output adjustable via potentiometer; 3 in 1 dimming; Timer dimming Typical lifetime > 00 hours 7 years warranty Applications LED street lighting LED highbay lighting Parking space lighting LED fishing lamp LED greenhouse lighting Type HL for use in Class Ⅰ, Division hazardous (Classified) location. Description is a W AC/DC LED driver featuring the dual mode constant voltage and constant current output. HLGH operates from 90~305VAC and offers models with different rated voltage rangingbetween 1V and 54V. Thanks to the high efficiency up to 91%, with the fanless design, the entire series is able to operate for 40 ~ case temperature under free air convection. The design of metal housing and IP67/IP65 ingress protection level allows this series to fit both indoor and outdoor applications. HLGH is equipped with various function options, such as dimming methodologies, so as to provide the optimal design flexibility for LED lighting system. Model Encoding HLG H 15 A Function options Rated output voltage (1V/15V/0V/4V/30V/36V/4V/48V/54V) Rated wattage Series name Type IP Level Function Note Blank IP67 Io and Vo fixed In Stock A IP65 Io and Vo adjustable through builtin potentiometer In Stock B IP67 3 in 1 dimming function (1~10VDC, 10V PWM signal and resistance) In Stock BL IP66 BType with junction box. UL8750 LISTED. Contact MEAN WELL for details By request D IP67 Timer dimming function, contact MEAN WELL for details(safety pending). By request
SPECIFICATION MODEL OUTPUT INPUT PROTECTION ENVIRONMENT SAFETY & EMC OTHERS NOTE DC VOLTAGE RATED CURRENT RATED POWER RIPPLE & NOISE (max.) Note. 150mVpp VOLTAGE ADJ. RANGE CURRENT ADJ. RANGE VOLTAGE TOLERANCE Note.3 LINE REGULATION LOAD REGULATION SETUP, RISE TIME HOLD UP TIME (Typ.) VOLTAGE RANGE FREQUENCY RANGE POWER FACTOR (Typ.) EFFICIENCY (Typ.) AC CURRENT (Typ.) INRUSH CURRENT (Typ.) LEAKAGE CURRENT OVER CURRENT OVER VOLTAGE OVER TEMPERATURE WORKING TEMP. WORKING HUMIDITY Note.6 ms,00ms/115vac 500ms,00ms/30VAC Note.5 STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS Note.8 EMC IMMUNITY MTBF 1V CONSTANT CURRENT REGION Note.4 7. ~1V TOTAL HARMONIC DISTORTION MAX. No. of PSUs on 16A CIRCUIT BREAKER SHORT CIRCUIT HLGH1 HLGH15 HLGH0 HLGH4 HLGH30 HLGH36 HLGH4 HLGH48 HLGH54 Adjustable for AType only (via builtin potentiometer) Adjustable for AType only (via builtin potentiometer) 3 ~ 5A ±.5% 16ms at full load 47 ~ 63Hz 30VAC /115VAC 88% 89% 90% 90.5% 91% 91% 91% 91% 91% 0.85A / 115VAC 0.45A / 30VAC 0.4A / 77VAC <0.75mA / 77VAC 95 ~ 108% 15V 9 ~ 15V 3 ~ 5A ±.0% Constant current limiting, recovers automatically after fault condition is removed Hiccup mode, recovers automatically after fault condition is removed 14 ~ 17V 18 ~ 4V 3 ~ 30V 8 ~ 35V 35 ~ 43V 41 ~ 49V 48 ~ 58V 54 ~ 63V 59 ~ 68V Shut down o/p voltage, repower on to recover Shut down o/p voltage, repower on to recover 0 ~ 95% RH noncondensing 40 ~, 10 ~ 95% RH ±0.03%/ (0 ~ ) 0V 1 ~ 0V.4 ~ 4A 10 ~ 500Hz, 5G 1min./1cycle, period for 7min. each along X, Y, Z axes UL8750(type HL ), CSA C. No. 50.008, UL8750 LISTED for HLGH BL; TUV EN613471, EN6134713 independent, optional models for J613471, J6134713, GB19510.1,GB19510.14,IP65 or IP67 approved ; Design refer to UL9501, TUV EN9501 Note.8 Compliance to En55015, EN3 Class C (@ load %) ; EN33,GB17743 and GB1765.1 Compliance to EN4,3,4,5,6,8,11, EN61547, light industry level (surge immunity LineEarth 4KV, LineLine KV) 357.8K hrs min. MILHDBK17F (5 ) 4V 14.4 ~ 4V.04 ~ 3.4A 1.6 ~.7A DIMENSION 195.6*61.5*38.8mm (L*W*H) PACKING 0.84Kg; 16pcs/14.4Kg/0.54CUFT 1. All parameters NOT specially mentioned are measured at 30VAC input, rated current and 5 of ambient temperature.. Ripple & noise are measured at 0MHz of bandwidth by using a 1" twisted pairwire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. Please refer to "DRIVING METHODS OF LED MODULE". 5. Derating may be needed under low input voltages. Please refer to STATIC CHARACTERISTIC sections for details. 6. Length of set up time is measured at first cold start. Turning ON/OFF the driver may lead to increase of the set up time. 7. The driver is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must requalify EMC Directive on the complete installation again. 8. To fulfill requirements of the latest ErP regulation for lighting fixtures, this LED driver can only be used behind a switch without permanently connected to the mains. 9. This series meets the typical life expectancy of >6,000 hours of operation when Tcase, particularly tc point (or TMP, per DLC), is about 75 or less. 10. Please refer to the warranty statement on MEAN WELL's website at http://www.meanwell.com 1.38 ~.3A 1.17 ~ 1.95A 1.0 ~ 1.7A ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% ±.0% ±1.5% ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% 30V 18 ~ 30V 36V 1.6 ~ 36V 5A 5A 4A 3.4A.7A.3A 1.95A 1.7A 48V 8.8 ~ 48V W 75W W 81.6W 81W 8.8W 81.9W 81.6W 10.8 ~ 13.5V MAX. CASE TEMP. Tcase= WITHSTAND VOLTAGE ISOLATION RESISTANCE EMC EMISSION 150mVpp 13.5 ~ 17V 150mVpp 17 ~ V 150mVpp ~ 7V 90 ~ 305VAC 17 ~ 431VDC (Please refer to "STATIC CHARACTERISTIC" section) 00mVpp 7 ~ 33V PF 0.96/115VAC, PF 0.96/30VAC, PF 0.94/77VAC @ full load (Please refer to " POWER FACTOR (PF) CHARACTERISTIC" section) THD< 0% (@ load % / 115VAC,30VAC; @ load 75% / 77VAC) (Please refer to " TOTAL HARMONIC DISTORTION (THD)" section) I/PO/P:3.75KVAC I/PFG:KVAC O/PFG:1.5KVAC I/PO/P, I/PFG, O/PFG:M Ohms / 500VDC / 5 / 70% RH 00mVpp 33 ~ 40V COLD START 70A(twidth=485 μs measured at 50% Ipeak) at 30VAC; Per NEMA 410 3 units (circuit breaker of type B) / 6 units (circuit breaker of type C) at 30VAC Tcase= 40 ~ (Please refer to "OUTPUT LOAD vs TEMPERATURE" section) 4V 5. ~ 4V 00mVpp 38 ~ 46V 00mVpp 43 ~ 53V 54V 3.4 ~ 54V 1.5A 81W 00mVpp 49 ~ 58V 0.9 ~ 1.5A ±0.5% ±0.5%
BLOCK DIAGRAM Fosc : KHz I/P FG EMI FILTER & RECTIFIERS PFC CIRCUIT O.T.P. O.L.P. POWER SWITCHING PWM & PFC CONTROL RECTIFIERS & FILTER O.L.P. DETECTION CIRCUIT V V DIM DIM (B Type) O.V.P. DRIVING METHODS OF LED MODULE This series is able to work in either Constant Current mode (a direct drive way) or Constant Voltage mode (usually through additional DC/DC driver) to drive the LEDs. In the constant current region, the highest voltage at the output of the driver depends on the configuration of the end systems. Vo(%) (A) Constant Voltage area (B) Constant Current area Should there be any compatibility issues, please contact MEAN WELL. (min.) (C) Hiccup Protection 50 Io (%) Typical output current normalized by rated current (%)
DIMMING OPERATION FG (Green/Yellow) HLGH V(Brown) V(Blue) DIM(Gray) DIM(Black) 3 in 1 dimming function (for BType) Output constant current level can be adjusted by applying one of the three methodologies between DIM and DIM: 1 ~ 10VDC, or 10V PWM signal or resistance. Direct connecting to LEDs is suggested. It is not suitable to be used with additional drivers. Dimming source current from power supply: μa (typ.) Applying additive 1 ~ 10VDC V V DIM DO NOT connect "DIM to V" Additive Voltage Output current (%) % 90% % 70% % 50% 40% 30% 0% 10% 1V V 3V 4V 5V 6V 7V 8V 9V 10V Dimming input: Additive voltage DIM Applying additive 10V PWM signal (frequency range Hz ~ 3KHz): V V DIM Additive PWM signal DIM DO NOT connect "DIM to V" Output current (%) % 90% % 70% % 50% 40% 30% 0% 10% 10% 0% 30% 40% 50% % 70% % 90% % Duty cycle of additive 10V PWM signal dimming input Applying additive resistance: V V DIM DIM Additive Resistance Output current (%) % 90% % 70% % 50% 40% 30% DO NOT connect "DIM to V" 0% 10% 10K/N 0K/N 30K/N 40K/N 50K/N K/N 70K/N K/N 90K/N K/N (N=driver quantity for synchronized dimming operation) Dimming input: Additive resistance
Note: In the case of turning the lighting fixture down to 0% brightness, please refer to the configuration as follow, or please contact MEAN WELL for other options. N FG L Relay Switch Adjuster 10K/N~K/N Ohms resistance 1~10V DC Voltage 10V PWM Signal Green/ Yellow Brown Blue AC/L AC/N HLGH BType DIM DIM V() V() Gray Black Blue Brown LED Lighting Fixture Using a switch and relay can turn ON/OFF the lighting fixture.
OUTPUT LOAD vs TEMPERATURE 30VAC Input only LOAD (%) 40 0 LOAD (%) 40 0 40 5 10 0 15 30 50 70 (HORIZONTAL) 40 5 0 0 45 55 65 75 (HORIZONTAL) AMBIENT TEMPERATURE,Ta ( ) Tcase ( ) STATIC CHARACTERISTICS POWER FACTOR(PF) CHARACTERISTIC Tcase at 70 Constant Current Mode LOAD (%) 90 70 50 40 90 15 135 145 155 165 175 1 00 30 305 INPUT VOLTAGE (V) Hz PF 1.00 0.98 0.96 0.94 0.9 0.90 0.88 0.86 0.84 0.8 0. 0.78 50% % 70% % 90% % LOAD (W) 77Vac 30Vac 115Vac Derating is needed under low input voltage. TOTAL HARMONIC DISTORTION (THD) 48V Model, Tcase at 70 18 16 EFFICIENCY vs LOAD possess superior working efficiency that up to 91% can be reached in field applications. 48V Model, Tcase at 70 9 14 88 THD(%) 1 10 8 6 4 77VAC 30VAC 115VAC EFFICIENCY (%) 84 76 7 77Vac 30Vac 115Vac 68 0 64 50% % 70% % 90% % 10% 0% 30% 40% 50% % 70% % 90% % LOAD LOAD
LIFE TIME 10 LIFETIME(Kh) 40 0 0 5 30 35 40 45 50 55 65 70 75 Tcase ( )
MECHANICAL SPECIFICATION Blank/DType Case No.997A Unit:mm 1 9.6 195.6 171.8 300±0 FG (Green/Yellow) SJOW 17AWG&H05RNF 1.0mm 3C 3 46.5 61.5 T case 30.75 tc 85.9 ψ4. 4PL 300±0 V(Brown) V(Blue) SJOW 17AWG&H05RNF 1.0mm C tc : Max. Case Temperature 38.8 AType 1 9.6 195.6 171.8 300±0 300±0 T case 85.9 V(Brown) tc FG (Green/Yellow) V(Blue) SJOW 17AWG&H05RNF 1.0mm 3C SJOW 17AWG&H05RNF 1.0mm C Io Vo ADJ. ADJ. 3 46.5 61.5 tc : Max. Case Temperature 38.8 BType 300±0 FG (Green/Yellow) SJOW 17AWG&H05RNF 1.0mm 3C tc : Max. Case Temperature 38.8 30.75 ψ4. 4PL 195.6 1 171.8 9.6 3 46.5 61.5 T case tc 30.75 85.9 300±0 SJOW 17AWG&H05RNF 1.0mm C SJOW 17AWG&H05RNF 1.0mm C ψ4. 4PL V(Brown) V(Blue) DIM(Gray) DIM(Black)
WATERPROOF CONNECTION Waterproof connector Waterproof connector can be assembled on the output cable of HLGH to operate in dry/wet/damp or outdoor environment. AC source I/P HLGH O/P Size Pin Configuration (Female) Size Pin Configuration (Female) M1 Order No. Suitable Current 4PIN 5A/PIN M104 10A max. 5PIN 5A/PIN M105 10A max. M15 Order No. Suitable Current PIN 1A/PIN M150 1A max. LED Lamp Cable Joiner 66 6 0 CJ041 suitable for 14AWG~16AWG CJ04 suitable for 18AWG~AWG ψ5 Up to four wires can be connected through this cable joiner by soldering or clamping by tools. LED Lamp HLGH O/P Wires CJ04 cable joiner can be purchased independently for user's own assembly. MEAN WELL order No. : CJ041, CJ04. Junction Box Option 171.8 334 76 10 5 FG (Green/Yellow) SJTW 18AWG 3C 35 38.8 61.5 61 6 3 8.5 8.5 V(Brown) V(Blue) SJOW 17AWG& H05RNF 1.0mm C ψ5 3 PF 1/" 150±0 3 PF 1/" 150±0 86 Junction box option is available for A / B / Blank Type. Please contact MEAW WELL for details. HLGH BL models with junction box on both input and output sides are UL LISTED approved(modified by B type only). INSTALLATION MANUAL Please refer to : http://www.meanwell.com/manual.html