Cisco 642-732 Conducting Cisco Unified Wireless Site(R) Survey Download Full Version : http://killexams.com/pass4sure/exam-detail/642-732
QUESTION: 172 Which tool can best provide throughput verification? A. WLC > Monitor > Clients > LinkTest B. WaveDeploy C. InSSIDer D. Xirrus Wi-Fi Inspector QUESTION: 173 After you have run the VoWLAN Voice Readiness Tool in WCS 7.0, you see there are potential problem areas in your facility. Which two actions will help you troubleshoot these coverage areas? (Choose two.) A. Verify the green, yellow, and red regions in the RF environment only if the floor has not been calibrated. B. To prevent one-way audio, set the AP power levels to half the power of the client. This will ensure proper radio coverage. C. You need to edit the RSSI values for Cisco IP Phones so the 802.11b/g/n radios display the region map properly. D. Determine if the coverage area will have enough APs to support the VoWLAN client, since all APs must have a Tx power level that does not exceed that of the client. E. Set the AP power level to match the VoWLAN client to avoid one-way audio. Answer: D, E QUESTION: 174 What is the attenuation of a wireless signal that passes through a cider block wall? A. 3 db B. 4 db C. 6 db D. 12 db QUESTION: 175
When using WCS 7.0 to calibrate a floor, is it more important to collect 50 or more distinct locations or to collect 150+ measurements? A. 150+ measurements are more important than the locations because the information gathered is more granular. B. Collecting 50 or more distinct locations is more important because this provides a wider coverage across the floor being calibrated. C. Depending on the size of the floor 50+ distinct locations and 150+ measurements may provide divergent information that requires more data collection. D. When calibrating a floor 50 or more distinct locations will yield 150+ measurements because multiple measurements are collected at each distinct location. Answer: D QUESTION: 176 Given an AP that can transmit at 100 mw and the client at 40 mw, which power setting should be used for a site survey? A. 10 mw B. 20 mw C. 40 mw D. 60 mw E. 80 mw F. 100 mw QUESTION: 177 What is the minimum CCX version necessary on a client when adding data points during WCS Calibration? A. CCXv1 B. CCXv2 C. CCXv3 D. CCXv4 E. CCXv5 QUESTION: 178
Which three basic pieces of information will you need to perform a WLAN site survey? (Choose three.) A. How many customer user interviews will be required? B. Which network hardware vendor do they currently use for their infrastructure? C. What is the location of the facility that needs to be surveyed? D. What financial information will my company need to provide to the customer? E. How many engineers will be required to perform the work? F. What is the expected timeline to complete the project? Answer: C, E, F QUESTION: 179 Which choice best describes RF challenges for outdoor mesh site survey and deployment? A. Reflection B. Reflection, absorption C. Diffraction D. Diffraction, scattering E. Reflection, absorption, diffraction, scattering Answer: E QUESTION: 180 Which regulation is OSHA responsible for enforcing? A. safety and health regulations B. fire and other hazard regulations C. electrical and wiring regulations D. radio communication regulations Answer: A QUESTION: 181 What document is required to build the Statement of Work? A. pre-survey questionnaire B. post-survey questionnaire C. site survey report
D. installation report Answer: A QUESTION: 182 Refer to the exhibit. After performing a Layer 1 survey using Cisco Spectrum Expert, what is the result indicated by the visual screen? A. Normal 802.11b activity B. Normal 802.11g activity C. Microwave oven interference D. Video camera interference E. Bluetooth device interference QUESTION: 183 Refer to the exhibit.
What is the most likely cause of MAP1 association to MAP2 instead of directly to the RAP? A. Incorrect BGN B. Default BGN C. SNR D. Absorption and scattering caused by weather conditions. E. Incorrect radio configuration Answer: C QUESTION: 184 Which wireless tool would be most useful in planning a WLAN solution prior to performing a site survey? A. Ekahau Survey B. Air Magnet Survey C. Air Magnet Wi-Fi Analyzer D. Cisco Spectrum Expert E. Cisco WCS Answer: E QUESTION: 185 After installation of a new data-only wireless network, an engineer found that RRM has set all of the APs to a power level of 1. Which option describes the reason for this? A. APs are too far apart for the set data rates. B. EDRRM is enabled. C. APs should be manually set initially. D. TPC needs to be enabled.
E. DTPC value is set too high. F. High co-channel interference exists. Answer: A QUESTION: 186 A customer has requested site surveys for data, voice, video, and location services for their location. The customer will be using RFID tags extensively. Which type of site survey should be conducted? A. data B. voice C. video D. location-based services E. bridging F. multi-survey Answer: D QUESTION: 187 A customer wants to deploy wireless services inside a 500-seat auditorium. Given the volume of potential users in this condensed area, what is the best option for AP deployment? A. place 802.11n APs along the outside edge with dual-band directional antennas B. place 802.11n APs along the outside edge with 2.4GHz directional antennas C. place 802.11n APs along the outside edge with 5GHz directional antennas D. place 802.11n APs in the center with 2.4GHz sector antennas E. place 802.11n APs in the center with 5GHz sector antennas F. place 802.11n APs in the center with dual-band sector antennas QUESTION: 188 An outdoor mesh network is being designed with one RAP and then a single RF hop to MAP1 and another single RF hop from MAP1 to MAP2 to extend coverage. Given that the initial RF backhaul at the RAP is operating at 24 Mb/s, what is the expected RF backhaul bandwidth at MAP2? A. 24 Mb/s B. 20 Mb/s
C. 14 Mb/s D. 7 Mb/s E. 3 Mb/s F. 1 Mb/s Answer: C QUESTION: 189 Refer to the exhibit. Which type of interference would the engineer detect on the Cisco Spectrum Expert? A. Bluetooth B. Wi-Max C. DECT phone D. microwave E. analog camera Answer: D QUESTION: 190 You have completed a WLAN site survey for a customer. Which two pieces of information
will need to be included in the final customer report? (Choose two.) A. Location and placement of application servers B. The number of active users that are planned to use the system in a specific area C. The number of APs dedicated to location services D. The results from customer end user interviews E. Analysis of WLAN signals on the networks of neighboring companies, C QUESTION: 191 Which two issues do access and backhaul radios experience in mesh networks? (Choose two.) A. The access radio has to connect to two or several points. B. The access cell usually covers more area at ground level that may have more sources of reflection and interference. C. The access cell radio range is larger than the backhaul radio range, which causes the backhaul cell radio to suffer from more interference. D. Backhaul radios are a bottleneck for throughput. E. RAPs help MAPs avoid coverage holes., D QUESTION: 192 DRAG DROP Answer: QUESTION: 193
An engineer is conducting a failover test with a Mesh deployment by disconnecting the network interface of a RAP. A MAP becomes stranded even though it has an acceptable RSSI value on the link to its neighbor. What are two reasons the MAP may become stranded? (Choose two.) A. the MAP is 6 hops away B. the MAP is 9 hops away C. the SNR on the neighbor link is 5dB D. the SNR on the neighbor link is 15dB E. the throughput on the neighbor link is 18Mbps F. the throughput on the neighbor link is 24Mbps, C
For More exams visit http://killexams.com Kill your exam at First Attempt...Guaranteed!