REFERENCE GUIDE External s Guide
Xirrus External s Guide Overview To optimize the overall performance of a Xirrus WLAN in an outdoor deployment it is important to understand how to maximize coverage with the appropriate antenna selection and placement. This document is meant to serve as a guideline for anyone who wishes to use Xirrus antennas and related accessories with Xirrus outdoor wireless products (XR-520H, XR-2425H, and XH2-120). The document is organized according to the following sub-sections: Basic Technical Background Types of available Xirrus s and Accessories Design Considerations and Reference Use Cases Technical Background ISM bands: The U.S. Federal Communications Commission (FCC) authorizes commercial wireless network products to operate in the Industrial, Scientific and Medical (ISM) bands using spread spectrum modulation. The ISM bands are located at three different frequencies ranges 900MHz, 2.4GHz and 5GHz. This document covers products that operate in the 2.4 and 5GHz bands. ISM bands allow manufacturers and users to operate wireless products in the U.S. without requiring specific licenses. This requirement may vary in other countries. The products themselves must meet certain requirements in order to be certified for sale such as maximum Transmit Power (Tx Power) and Effective Isotropic Radiated Power (EIRP) ratings. Each of the ISM bands has different characteristics. The lower frequency bands exhibit better range but with limited bandwidth and hence lower data rates. Higher frequency bands have less range and are subject to greater attenuation from solid objects. Properties, Ratings and Representation At the most fundamental level an provides a wireless communication system three main attributes that are inter-related to each other and ultimately influence the overall radiation pattern produced by the antenna: Gain Directivity Polarization Gain of an is a measure of the increase in power that the antenna provides. gain is measured in decibels (db) a logarithmic unit used to express the ratio between two values of a given physical quantity. In the general case, the gain in db is a factor of the ratio of output power (or radiated power) to the input power of the antenna (that ratio is also called the efficiency of the antenna). In practice, the gain of a given antenna is commonly expressed by comparing it to the gain of an isotropic antenna. An isotropic antenna is a theoretical antenna with a perfectly uniform three-dimensional radiation pattern. When expressed relative to an isotropic antenna, the gain of a given antenna is represented in dbi (i for isotropic). By that measure, a truly isotropic antenna would have a power rating of 0 db. The U.S. FCC uses dbi in its calculations. Directivity is the factor that was referred to in the previous discussion about antenna gain and its relation to efficiency. Mathematically, the gain of an antenna is its directivity times its efficiency. And like its gain, the directivity of a given antenna is also expressed relative to an isotropic antenna. The directivity measures the power density that an antenna radiates in the direction of its strongest emission, relative to the power density radiated by an ideal isotropic antenna (which emits uniformly in all directions), when they are both radiating the same total power. Polarization of an antenna is the orientation of the electric field of the radio wave that it produces relative to the earth s surface. The polarization of an antenna is determined by the physical structure of the antenna and by its
orientation. A simple straight wire antenna will have one polarization when mounted vertically and a different polarization when mounted horizontally. A linear polarized antenna radiates wholly in one plain containing the direction of propagation of the radio wave while, in a circular polarized antenna, the plane of polarization rotates in a circle making one complete revolution during one period of the wave. A linear polarized antenna may be either Horizontally Polarized (if the direction of propagation is parallel to the earth s surface) or Vertically Polarized (if the direction of propagation is perpendicular to the earth s surface). A circular polarized antenna may be either Right-Hand-Circular (RHC) or Left-Hand-Circular (LHC) depending on whether the direction of rotation of the plane of propagation is clockwise or counterclockwise respectively. Polarization is an important design consideration, particularly in Line of Sight (LOS) or Point-to-Point type deployments because maximum signal strength between sending and receiving antennas occurs when both are using identical polarization. Radiation Pattern of an antenna is a plot of the relative strength of the electromagnetic field of the radio waves emitted by the antenna at different angles. The radiation pattern of the theoretical isotropic antenna, which radiates equally in all directions, would look like a sphere. Matching is an important consideration in the design of the overall wireless communication system. At each interface, depending on the impedance mismatch, some fraction of the propagating radio wave s energy will reflect back into the source. This reflecting wave is called a standing wave and the ratio of maximum power to minimum power in the standing wave is called the Voltage Standing Wave Ratio (VSWR). A VSWR of 1:1 is ideal. Types of Xirrus s The tables starting on the next page detail the specifications of the different antennas Xirrus offers for use with its Access Points, in both 2.4GHz and 5GHz. Each type of antenna will offer certain coverage capabilities suited for specific applications (as discussed in the later section of this document). As a general rule of thumb as the gain of an antenna increases, there is some tradeoff to its coverage area. High gain antennas will typically offer longer coverage distance but smaller (and more directed) coverage area. s 15 degree 2.4GHz (ANT-DIR15-2X2-2.4G-01) 15 degree 5GHz (ANT-DIR15-2X2-5.0G-01) 30 degree Dual Band* (ANT-DIR30-2X2-01) 60 degree Dual Band* (ANT-DIR60-2X2-01) 90 degree Dual Band (ANT-DIR90-2X2-01) Rubber Duck Dual Band (ANT-OMNI-1x1-02) Rubber Duck Dual Band (ANT-OMNI-1x1-03) OMNI Dual Band* (ANT-OMNI-2x2-02) OMNI Dual Band* (ANT-OMNI-2x2-03) and Cables (Per Radio) XR-520H ANT-CAB-195-10-MM XR-2425H ANT-CAB-195-10-MM XH2-120 ANT-CAB-195-10-MM-02 1 + 2 cables 1 + 2 cables 1 + 2 cables 1 + 2 cables 1 + 2 cables 1 + 2 cables 1 + 2 cables 1 + 2 cables 1 + 2 cables 1 + 2 cables 1 + 2 cables 1 + 2 cables 1 + 2 cables 1 + 2 cables 1 + 2 cables 2 s, Direct attach 2 s, Direct attach N/A N/A N/A 2 s, Direct attach 1 s Direct attach 1, Direct attach N/A N/A N/A 1 + 2 cables * Each antenna can be connected simultaneously to 2 radios on different bands (2.4GHz and 5GHz) with additional cables. Additional antennas and cables are required to connect multiple radios on the same band.
Directional s 15 for 2.4 GHz band (ANT-DIR15-2x2-2.4G-01) Front / Connectors 15 for 2.4 GHz band (ANT-DIR15-2x2-2.4G-01) 15 SINGLE BAND 2.4GHz 2x2 PANEL ANTENNA Gain Patterns Vertical Gain Pattern Horizontal Gain Pattern Frequency Range (GHz) 2.4 2.5 VSWR () 1.5 Peak Gain, dbi (2.4GHz) 17+/- 1 Polarization 2 x +/ 45 Half-Power Beamwidth AZ (H) 16 +/- 3 Half-Power Beamwidth EL (V) 15 +/- 3 50W Connector N-Female x 2 17.7in x 17.7in x 1.6in 4.4lbs -40 C to +55 C Mounting Options Pole Mount included (Pole Outer Diamater 1.6-2 ) Cable Specs XR-520H, XR-2425H XH2-120 Extension Cable (per radio) LMR-195 male RP-TNC to male N Connector, 10 length (ANT-CAB-195-10-MM) LMR-195 male N connectors at both ends, 10 length (ANT-CAB-195-10-MM-02) LMR-400 male N to female N, 10 length (ANT-CAB-400-10-MF) For use with XR-520H and XR-2425H: 1 ANT-DIR15 2x2-XXX-01 2 ANT-CAB-195-10-MM For use with XH2-120: 1 ANT-DIR15-2X2-XXX-01 2 ANT-CAB-195-10-MM-02
15 for 5 GHz band (ANT-DIR15-2x2-5.0G-01) Directional s Front / Connectors 15 for 5 GHz band (ANT-DIR15-2x2-5.0G-01) 15 SINGLE BAND 5GHz 2x2 PANEL ANTENNA Gain Patterns Vertical Gain Pattern Horizontal Gain Pattern Frequency Range (GHz) 5.15-5.85 VSWR () 1.8 Peak Gain, dbi (5GHz) 17+/- 1 Polarization V/H Half-Power Beamwidth Az (H) 17 Half-Power Beamwidth El (V) 17 20W Connector N-Female x 2 10.3in x 10.3in x 1.4in 2.5lbs -40 C to +55 C Mounting Options Pole Mount included (pole outer diameter 1.6-2 ) Cable Specs XR-520H, XR-2425H XH2-120 Extension Cable (per radio) LMR-195 male RP-TNC to male N Connector, 10 length (ANT-CAB-195-10-MM) LMR-195 male N connectors at both ends, 10 length (ANT-CAB-195-10-MM-02) LMR-400 male N to female N, 10 length (ANT-CAB-400-10-MF) For use with XR-520H and XR-2425H: 1 ANT-DIR15-2x2-XXX-01 2 ANT-CAB-195-10-MM For use with XH2-120: 1 ANT-DIR15-2X2-XXX-01 2 ANT-CAB-195-10-MM-02
30 (ANT-DIR30-2x2-01) Front 30 (ANT-DIR30-2x2-01) 30 DUAL BAND 2x2 PANEL ANTENNA Gain Patterns Vertical Gain Pattern Horizontal Gain Pattern Directional s / Connectors Frequency Range (GHz) 2.4 2.5 5.15-5.825 VSWR () 2.0: 1 max. typ. Peak Gain, dbi (2.4 and 5GHz) 11.7-13.5 12.5-14.0 Polarization 2 x +/ 45, V 2 x +/ 45, V 3dB Beamwidth Az (H) 35 +/- 5 3dB Beamwidth El (V) 35 +/- 5 10 W max. Connector N-Female x 2 N-Female x 2 16.5in x 9.4in x 1.4 in 3.75lbs -40 C to +55 C Mounting Options Pole Mount included Cable Specs XR-520H, XR-2425H XH2-120 Extension Cable (per radio)* LMR-195 male RP-TNC to male N Connector, 10 length (ANT-CAB-195-10-MM) LMR-195 male N connectors at both ends, 10 length (ANT-CAB-195-10-MM-02) LMR-400 male N to female N, 10 length (ANT-CAB-400-10-MF) For use with XR-520H and XR-2425H: 1 ANT-DIR30-2x2-01 2 ANT-CAB-195-10-MM For use with XH2-120: 1 ANT-DIR30-2x2-01 2 ANT-CAB-195-10-MM-02 * Each antenna can be connected simultaneously to 2 radios on different bands (2.4GHz and 5GHz) with two additional cables. Additional antennas and cables are required to connect multiple radios on the same band.
60 (ANT-DIR60-2x2-01) Front 60 (ANT-DIR60-2x2-01) 60 DUAL BAND 2x2 PANEL ANTENNA Gain Patterns Vertical Gain Pattern Horizontal Gain Pattern Frequency Range (GHz) 2.4 2.48 5.15-5.850 Directional s / Connectors VSWR () 2.0:1 max. typ. Peak Gain, dbi (2.4 and 5GHz) 7-10 8.5-9.5 Polarization 2 x +/ 45, V 2 x +/ 45, V 3dB Beamwidth Az (H) 65 +/- 5 3dB Beamwidth El (V) 65 +/- 5 10 W max Connector N-Female x 3 N-Female x 3 8.6in x 8.6in x 1.18in 1.49lbs -40 C to +55 C Mounting Options Pole Mount included Cable Specs XR-520H, XR-2425H XH2-120 Extension Cable (per radio)* LMR-195 male RP-TNC to male N Connector, 10 length (ANT-CAB-195-10-MM) LMR-195 male N connectors at both ends, 10 length (ANT-CAB-195-10-MM-02) LMR-400 male N to female N, 10 length (ANT-CAB-400-10-MF) For use with XR-520H and XR-2425H: 1 ANT-DIR60-2x2-01 2 ANT-CAB-195-10-MM For use with XH2-120: 1 ANT-DIR60-2X2-01 2 ANT-CAB-195-10-MM-02 * Each antenna can be connected simultaneously to 2 radios on different bands (2.4GHz and 5GHz) with two additional cables. Additional antennas and cables are www.4gon.co.uk info@4gon.co.uk Tel: required +44 to connect (0)1245 multiple radios on the same 808295 band. Fax: +44 (0)1245 808299
90 (ANT-DIR90-2x2-01) Connectors Closeup 90 (ANT-DIR90-2x2-01) 90 DUAL BAND 2x2 PANEL ANTENNA Gain Patterns Vertical Gain Pattern Horizontal Gain Pattern Directional s Back Front Frequency Range (GHz) 2.4 2.5 5.15-5.85 VSWR () 2.0:1 max. typ. Peak Gain, dbi (2.4 and 5GHz) 4.0 6.5-9.5 Polarization Vertical 3dB Beamwidth Az (H) 90 typ. 3dB Beamwidth El (V) 90 typ. 10 W max Connector N-Female x 2* 98in x 9in x 1.96in 1.7lbs -40 C to +60 C Mounting Options Pole Mount Cable Specs XR-520H, XR-2425H XH2-120 (per radio) LMR-195 male RP-TNC to male N Connector, 10 length (ANT-CAB-195-10-MM) LMR-195 male N connectors at both ends, 10 length (ANT-CAB-195-10-MM-02) For use with XR-520H and XR-2425H: 1 ANT-DIR90-2x2-01 2 ANT-CAB-195-10-MM For use with XH2-120: 1 ANT-DIR90-2x2-01 2 ANT-CAB-195-10-MM-02 * Connectors apply for both 2.4 and 5GHz bands.
Rubber Duck (ANT-OMNI-1x1-02) Connector Closeup Rubber Duck (ANT-OMNI-1x1-02) Gain Patterns 360 DUAL BAND(OMNI DIRECTIONAL) 1X1 ANTENNA (only with XR-520H and XR-2425H) Vertical Gain Pattern Omni-Directional s Frequency Range (GHz) 2.4 2.5 5.15-5.825 VSWR () 2.0:1 max. typ. Peak Gain, dbi (2.4 and 5GHz) -1.54-0 -1.7 Polarization 4 x Vertical 3dB Beamwidth Az (H) 360 3dB Beamwidth El (V) 90 60 10 W max. Connector RP-TNC-male x 1* 6.1in x 0.5in (Diameter) 0.05lbs -10 C to +70 C Mounting Options direct mount to AP (per radio) For use with XR-520H and XR-2425H: 2 ANT-OMNI-1x1-02 * Connectors apply for both 2.4 and 5GHz bands.
Rubber Duck (ANT-OMNI-1X1-03) Connector Closeup Rubber Duck (ANT-OMNI-1x1-03) Gain Patterns 360 DUAL BAND (OMNI DIRECTIONAL) 1x1 ANTENNA (only for the XH2-120) Vertical Gain Pattern Omni-Directional s Frequency Range (GHz) 2.4 2.5 5.15-5.35, 5.725-5.85 MHz VSWR () 2.0:1 max. typ. Peak Gain, dbi (2.4 and 5GHz) 2.0 4.0 Polarization Linear Vertical 3dB Beamwidth Az (H) 360 (Omnidirectional) 3dB Beamwidth El (V) 90 60 10 W max. Connector N-Male x 1* 7.59in x 0.5in (Diameter) 0.1lbs -10 C to +70 C Mounting Options direct mount to AP (per radio) For use with XH2-120: 2 ANT-OMNI-1x1-03 * Connectors apply for both 2.4 and 5GHz bands.
2x2 Omni (ANT-OMNI-2x2-02) Connectors Closeup 2x2 Omni (ANT-OMNI-2x2-02) Gain Patterns 360 DUAL BAND (OMNI DIRECTIONAL) 2x2 ANTENNA (only for XR-520H and XR-2425H) Vertical Gain Pattern Omni-Directional s Mounts Frequency Range (GHz) 2.4 2.5 5.15-5.825 VSWR () 2.0:1 max. typ. Peak Gain, dbi (2.4 and 5GHz) 2.3 5 Polarization 4 x V(Linear, Vertical) 3dB Beamwidth Az (H) 360 3dB Beamwidth El (V) 60 10 W Connector RP-TNC male x 2 RP-TNC male x 2 8.6in x 6.3in (Diameter) 3lbs -30 C to +70 C Ingress Protection IP-54 Mounting Options 1.5 stud mount Universal wall and mast mountable with included articulating mount. All tools and hardware included. Mounts to mast up to 1-1/2 in diameter. Ceiling mountable to 1 thick ceiling tile with jam nut. Also includes rubber washer for mounting to smooth surfaces such as NEMA enclosures. (per radio)* For use with XR-520H and XR-2425H: 1 ANT-OMNI-2x2-02 * Each antenna can be connected simultaneously to 2 radios on different bands (2.4GHz and 5GHz). Additional antennas and cables are required to connect www.4gon.co.uk info@4gon.co.uk Tel: multiple +44 radios on (0)1245 the same band. 808295 Fax: +44 (0)1245 808299
2x2 Omni (ANT-OMNI-2x2-03) 2x2 Omni (ANT-OMNI-2x2-03) Gain Patterns 360 DUAL BAND (OMNI DIRECTIONAL) 2x2 ANTENNA (only for XH2-120) Vertical Gain Pattern Omni-Directional s Frequency Range (GHz) 2.4 2.5 5.15-5.85 VSWR () 1.7 max. typ. 2.0 max. typ. Peak Gain, dbi (2.4 and 5GHz) 2.3 3.5 Polarization 4 x Vertical 3dB Beamwidth Az (H) 360 360 3dB Beamwidth El (V) 60 50 50 W Connector N-Female x 2 N-Female x 2 7.87in X 4.44in (Diameter) 1.43lbs -40 C to + 55 C Rated Wind Velocity 36.9 (m/s) 82.5 mph Mounting Options Pole mount: 40-70mm OD, 1.6-2.75in OD Cable Specs XH2-120 Extension Cable (per radio)* LMR-195 male N connectors at both ends, 10 length (ANT-CAB-195-10-MM-02) LMR-400 male N to female N, 10 length (ANT-CAB-400-10-MF) For use with XH2-120: 1 ANT-OMNI-2x2-03 2 ANT-CAB-195-10-MM-02 * Each antenna can be connected simultaneously to 2 radios on different bands (2.4GHz and 5GHz) with two additional cables. Additional antennas and cables are www.4gon.co.uk info@4gon.co.uk Tel: required +44 to connect (0)1245 multiple radios on the same 808295 band. Fax: +44 (0)1245 808299
Design Considerations and Reference Use Cases There are several factors that impact the performance of a Wireless LAN and must be kept in mind while designing for a deployment. Some of the key considerations are as follows: Mobility of the Application: The mobility of the clients that will be connecting to the Array through the antenna system is the first thing to think about when planning a deployment. An application that has a lot of mobile users, such as a convention center is best served by a large number of omnidirectional microcells while a point-to-point application, which connects two or more stationary users may be best served by a directional antenna. Physical Environment: Some of the things to watch for in the environment where the WLAN deployment is planned include: Building construction The density of the materials used in a building s construction determines the number of walls the RF signal can pass through and still maintain adequate coverage. The following is a good reference but the actual effect of the walls on RF must be tested through a site survey. A thick metal wall, such as an elevator reflects signals, resulting in poor penetration of the signal and low quality of reception on the other side. Solid walls and floors and precast concrete walls can limit signal penetration to one or two walls without degrading coverage, but, this can vary greatly depending on the amount of steel reinforcing within the concrete. Concrete and concrete block walls will likely limit signal penetration to three or four walls. Wood or dry wall will typically allow for adequate signal penetration through five or six walls. Paper and Vinyl walls have little effect on signal penetration. Ceiling height Internal obstructions Product inventory and racking are factors to consider in a indoor environment, such as a warehouse. In outdoor environments, many objects can affect antenna patterns, including trees, vehicles and buildings. Available mounting locations. In addition, consideration some consideration should also be given to aesthetic appearance. Access to network connections (minimize cable runs): Cabling between the Array or AP and the antenna introduces losses in the system, therefore the length of this cable run must be minimized as much as possible. Warehouse Use Case: In most cases, these installations require a large coverage area. Experience has shown that multiple omnidirectional antennas (such as ANT-OMNI-1x1-01 or ANTOMNI-2x2-02) mounted at 20 or 25 feet typically provide the best coverage. Of course this is also affected by the height of the racking, the material in the racks and your ability to locate the antenna at this height. The antenna should be placed in the center of the desired coverage cell an in an open area for best performance. In cases where the ceiling is too high and the Array or AP will be located against a wall, a directional antenna may be used. Small Office or Small Retail Store: An omnidirectional dipole antenna (such as ANT-OMNI-1x1-01 or ANT-OMNI-2x2-02) will provide best coverage for type of scenario. Enterprise or Large Retail Store: In most such deployments, there is a need for a fairly large coverage area and a combination of omnidirectional and directional antennas must be used. Omnidirectional antennas located just below the ceiling girders or just below the drop ceiling and directional antennas located at the corners. Also, for areas that are long and narrow such as long store aisles a directional antenna at one end may provide better coverage. Keep in mind that the radiation angle of the antenna will also affect the coverage area. Apartment Complex Backhaul (Point-to-Point): For an application where last mile connectivity is being provided using Wi-Fi (such as apartment complexes or senior living complexes that may not have traditional wiring infrastructure), point-to-point connections are common. When establishing point to point connections in outdoor environments, the distance, obstructions
IB HigherEdu 1115-001 and antenna locations must be considered. For short distances (several hundred feet), a standard dipole antenna may be used. For very large distances (1/2 mile or more) high-gain directional antennas must be used. The antennas must be installed as high as possible, above obstructions such as trees, buildings and similar. If directional antennas are used, they must be aligned so that their main radiated power lobes are directed at each other. Support & Maintenance Xirrus is committed to the success of our customers and provides warranties and support options to best fit your needs.. For further information on the Xirrus hardware warranties, software support and premium support offerings visit: http://www.xirrus.com/support/ About Xirrus To organizations who depend on wireless access to transform their business, Xirrus is the wireless network solution provider that provides the world s most powerful, scalable, and trusted solutions. Through product invention and system design, commitment to customer success, and the industry s best price performance, Xirrus gives you confidence that your wireless network performs under even the most demanding circumstances. Xirrus is a privately held company headquartered in Thousand Oaks, CA.